Some PRM functions will need to be called by the hwmod code early in
kernel init.  To handle this, split the PRM initialization code into
early and late phases.  The early init is handled via mach-omap2/io.c,
while the late init is handled by subsys_initcall().
Signed-off-by: NPaul Walmsley <paul@pwsan.com>

Add SoC reset functions into the PRM code.  These functions are based
on code from mach-omap2/prcm.c.  They reset the SoC using the CORE DPLL
reset method (as opposed to one of the other two or three chip reset
methods).

Adding them here will facilitate their removal from
arch/arm/mach-omap2/prcm.c.  (prcm.c is deprecated.)
Signed-off-by: NPaul Walmsley <paul@pwsan.com>
Tested-by: NVaibhav Hiremath <hvaibhav@ti.com>

The OMAP watchdog timer driver needs to determine what caused the SoC
to reset for its GETBOOTSTATUS ioctl.  So, define a set of standard
reset sources across OMAP SoCs.  For OMAP2xxx, 3xxx, and 4xxx SoCs,
define mappings from the SoC-specific reset source register bits to
the standardized reset source IDs.  Create SoC-specific PRM functions
that read the appropriate per-SoC register and use the mapping to
return the standardized reset bits.  Register the SoC-specific PRM
functions with the common PRM code via prm_register().  Create a
function in the common PRM code, prm_read_reset_sources(), that
calls the SoC-specific function, registered during boot.

This patch does not yet handle some SoCs, such as AM33xx.  Those SoCs
were not handled by the code this will replace.
Signed-off-by: NPaul Walmsley <paul@pwsan.com>

Move the low-level SoC-specific clockdomain control functions into
cm*.c and prm*.c.  For example, OMAP2xxx low-level clockdomain
functions go into cm2xxx.c.  Then remove the unnecessary
clockdomain*xxx*.c files.

The objective is to centralize low-level CM and PRM register accesses
into the cm*.[ch] and prm*.[ch] files, and then to export an OMAP
SoC-independent API to higher-level OMAP power management code.
Signed-off-by: NPaul Walmsley <paul@pwsan.com>
Cc: Rajendra Nayak <rnayak@ti.com>
Cc: Vaibhav Hiremath <hvaibhav@ti.com>
Acked-by: NRajendra Nayak <rnayak@ti.com>
Reviewed-by: NRuss Dill <Russ.Dill@ti.com>
Acked-by: NSantosh Shilimkar <santosh.shilimkar@ti.com>

Move OMAP3xxx-specific PRM functions & macros into prm3xxx.[ch] and
OMAP2xxx-specific macros into prm2xxx.h.  (prm2xxx.c will be created
by a subsequent patch when it's needed.)  Move basic PRM register
access functions into static inline functions in prm2xxx_3xxx.h, leaving
only OMAP2/3 hardreset functions in prm2xxx_3xxx.c.

Also clarify the initcall function naming to reinforce that this code
is specifically for the PRM IP block.

This is in preparation for the upcoming powerdomain series and the
upcoming move of this code to drivers/.
Signed-off-by: NPaul Walmsley <paul@pwsan.com>
Reviewed-by: NRuss Dill <Russ.Dill@ti.com>
Acked-by: NSantosh Shilimkar <santosh.shilimkar@ti.com>