When having a decrementor interrupt pending, the dequeuing happens manually
through an mtdec instruction. This instruction simply calls dequeue on that
interrupt, so the int_pending hint doesn't get updated.

This patch enables updating the int_pending hint also on dequeue, thus
correctly enabling guests to stay in guest contexts more often.
Signed-off-by: NAlexander Graf <agraf@suse.de>

Now that the actual mtsr doesn't do anything anymore, we can move the sr
contents over to the shared page, so a guest can directly read and write
its sr contents from guest context.
Signed-off-by: NAlexander Graf <agraf@suse.de>

Right now we're examining the contents of Book3s_32's segment registers when
the register is written and put the interpreted contents into a struct.

There are two reasons this is bad. For starters, the struct has worse real-time
performance, as it occupies more ram. But the more important part is that with
segment registers being interpreted from their raw values, we can put them in
the shared page, allowing guests to mess with them directly.

This patch makes the internal representation of SRs be u32s.
Signed-off-by: NAlexander Graf <agraf@suse.de>

When hitting a no-execute or read-only data/inst storage interrupt we were
flushing the respective PTE so we're sure it gets properly overwritten next.

According to the spec, this is unnecessary though. The guest issues a tlbie
anyways, so we're safe to just keep the PTE around and have it manually removed
from the guest, saving us a flush.
Signed-off-by: NAlexander Graf <agraf@suse.de>

When the guest jumps into kernel mode and has the magic page mapped, theres a
very high chance that it will also use it. So let's detect that scenario and
map the segment accordingly.
Signed-off-by: NAlexander Graf <agraf@suse.de>

We have a debug printk on every exit that is usually #ifdef'ed out. Using
tracepoints makes a lot more sense here though, as they can be dynamically
enabled.

This patch converts the most commonly used debug printks of EXIT_DEBUG to
tracepoints.
Signed-off-by: NAlexander Graf <agraf@suse.de>

Add kvm_release_page_clean() after is_error_page() to avoid
leakage of error page.
Signed-off-by: NWei Yongjun <yjwei@cn.fujitsu.com>
Signed-off-by: NAvi Kivity <avi@redhat.com>

We need to override EA as well as PA lookups for the magic page. When the guest
tells us to project it, the magic page overrides any guest mappings.

In order to reflect that, we need to hook into all the MMU layers of KVM to
force map the magic page if necessary.
Signed-off-by: NAlexander Graf <agraf@suse.de>
Signed-off-by: NAvi Kivity <avi@redhat.com>

On PowerPC it's very normal to not support all of the physical RAM in real mode.
To check if we're matching on the shared page or not, we need to know the limits
so we can restrain ourselves to that range.

So let's make it a define instead of open-coding it. And while at it, let's also
increase it.
Signed-off-by: NAlexander Graf <agraf@suse.de>

v2 -> v3:

  - RMO -> PAM (non-magic page)
Signed-off-by: NAvi Kivity <avi@redhat.com>

When the guest turns on interrupts again, it needs to know if we have an
interrupt pending for it. Because if so, it should rather get out of guest
context and get the interrupt.

So we introduce a new field in the shared page that we use to tell the guest
that there's a pending interrupt lying around.
Signed-off-by: NAlexander Graf <agraf@suse.de>
Signed-off-by: NAvi Kivity <avi@redhat.com>

When running in hooked code we need a way to disable interrupts without
clobbering any interrupts or exiting out to the hypervisor.

To achieve this, we have an additional critical field in the shared page. If
that field is equal to the r1 register of the guest, it tells the hypervisor
that we're in such a critical section and thus may not receive any interrupts.
Signed-off-by: NAlexander Graf <agraf@suse.de>
Signed-off-by: NAvi Kivity <avi@redhat.com>

To communicate with KVM directly we need to plumb some sort of interface
between the guest and KVM. Usually those interfaces use hypercalls.

This hypercall implementation is described in the last patch of the series
in a special documentation file. Please read that for further information.

This patch implements stubs to handle KVM PPC hypercalls on the host and
guest side alike.
Signed-off-by: NAlexander Graf <agraf@suse.de>
Signed-off-by: NAvi Kivity <avi@redhat.com>

When in kernel mode there are 4 additional registers available that are
simple data storage. Instead of exiting to the hypervisor to read and
write those, we can just share them with the guest using the page.

This patch converts all users of the current field to the shared page.
Signed-off-by: NAlexander Graf <agraf@suse.de>
Signed-off-by: NAvi Kivity <avi@redhat.com>

The SRR0 and SRR1 registers contain cached values of the PC and MSR
respectively. They get written to by the hypervisor when an interrupt
occurs or directly by the kernel. They are also used to tell the rfi(d)
instruction where to jump to.

Because it only gets touched on defined events that, it's very simple to
share with the guest. Hypervisor and guest both have full r/w access.

This patch converts all users of the current field to the shared page.
Signed-off-by: NAlexander Graf <agraf@suse.de>
Signed-off-by: NAvi Kivity <avi@redhat.com>

The DAR register contains the address a data page fault occured at. This
register behaves pretty much like a simple data storage register that gets
written to on data faults. There is no hypervisor interaction required on
read or write.

This patch converts all users of the current field to the shared page.
Signed-off-by: NAlexander Graf <agraf@suse.de>
Signed-off-by: NAvi Kivity <avi@redhat.com>

The DSISR register contains information about a data page fault. It is fully
read/write from inside the guest context and we don't need to worry about
interacting based on writes of this register.

This patch converts all users of the current field to the shared page.
Signed-off-by: NAlexander Graf <agraf@suse.de>
Signed-off-by: NAvi Kivity <avi@redhat.com>

One of the most obvious registers to share with the guest directly is the
MSR. The MSR contains the "interrupts enabled" flag which the guest has to
toggle in critical sections.

So in order to bring the overhead of interrupt en- and disabling down, let's
put msr into the shared page. Keep in mind that even though you can fully read
its contents, writing to it doesn't always update all state. There are a few
safe fields that don't require hypervisor interaction. See the documentation
for a list of MSR bits that are safe to be set from inside the guest.
Signed-off-by: NAlexander Graf <agraf@suse.de>
Signed-off-by: NAvi Kivity <avi@redhat.com>

For transparent variable sharing between the hypervisor and guest, I introduce
a shared page. This shared page will contain all the registers the guest can
read and write safely without exiting guest context.

This patch only implements the stubs required for the basic structure of the
shared page. The actual register moving follows.
Signed-off-by: NAlexander Graf <agraf@suse.de>
Signed-off-by: NAvi Kivity <avi@redhat.com>

We just introduced generic functions to handle shadow pages on PPC.
This patch makes the respective backends make use of them, getting
rid of a lot of duplicate code along the way.
Signed-off-by: NAlexander Graf <agraf@suse.de>
Signed-off-by: NMarcelo Tosatti <mtosatti@redhat.com>

Instead of instantiating a whole thread_struct on the stack use only the
required parts of it.
Signed-off-by: NAndreas Schwab <schwab@linux-m68k.org>
Tested-by: NAlexander Graf <agraf@suse.de>
Signed-off-by: NMarcelo Tosatti <mtosatti@redhat.com>

All vcpu ioctls need to be locked, so instead of locking each one specifically
we lock at the generic dispatcher.

This patch only updates generic ioctls and leaves arch specific ioctls alone.
Signed-off-by: NAvi Kivity <avi@redhat.com>

Signed-off-by: NAvi Kivity <avi@redhat.com>

vmx and svm vcpus have different contents and therefore may have different
alignmment requirements.  Let each specify its required alignment.
Signed-off-by: NAvi Kivity <avi@redhat.com>

Signed-off-by: NStephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: NMarcelo Tosatti <mtosatti@redhat.com>

When we're on a paired single capable host, we can just always enable
paired singles and expose them to the guest directly.

This approach breaks when multiple VMs run and access PS concurrently,
but this should suffice until we get a proper framework for it in Linux.
Signed-off-by: NAlexander Graf <agraf@suse.de>
Signed-off-by: NAvi Kivity <avi@redhat.com>

When in split mode, instruction relocation and data relocation are not equal.

So far we implemented this mode by reserving a special pseudo-VSID for the
two cases and flushing all PTEs when going into split mode, which is slow.

Unfortunately 32bit Linux and Mac OS X use split mode extensively. So to not
slow down things too much, I came up with a different idea: Mark the split
mode with a bit in the VSID and then treat it like any other segment.

This means we can just flush the shadow segment cache, but keep the PTEs
intact. I verified that this works with ppc32 Linux and Mac OS X 10.4
guests and does speed them up.
Signed-off-by: NAlexander Graf <agraf@suse.de>
Signed-off-by: NAvi Kivity <avi@redhat.com>

When we get a performance counter interrupt we need to route it on to the
Linux handler after we got out of the guest context. We also need to tell
our handling code that this particular interrupt doesn't need treatment.

So let's add those two bits in, making perf work while having a KVM guest
running.
Signed-off-by: NAlexander Graf <agraf@suse.de>
Signed-off-by: NAvi Kivity <avi@redhat.com>

There are some pieces in the code that I overlooked that still use
u64s instead of longs. This slows down 32 bit hosts unnecessarily, so
let's just move them to ulong.
Signed-off-by: NAlexander Graf <agraf@suse.de>
Signed-off-by: NAvi Kivity <avi@redhat.com>

We have a define on what the highest bit of IRQ priorities is. So we can
just as well use it in the bit checking code and avoid invalid IRQ values
to be triggered.
Signed-off-by: NAlexander Graf <agraf@suse.de>
Signed-off-by: NAvi Kivity <avi@redhat.com>

Some code we had so far required defines and had code that was completely
Book3S_64 specific. Since we now opened book3s.c to Book3S_32 too, we need
to take care of these pieces.

So let's add some minor code where it makes sense to not go the Book3S_64
code paths and add compat defines on others.
Signed-off-by: NAlexander Graf <agraf@suse.de>
Signed-off-by: NAvi Kivity <avi@redhat.com>

Book3S_32 doesn't know about segment faults. It only knows about page faults.
So in order to know that we didn't map a segment, we need to fake segment
faults.

We do this by setting invalid segment registers to an invalid VSID and then
check for that VSID on normal page faults.
Signed-off-by: NAlexander Graf <agraf@suse.de>
Signed-off-by: NAvi Kivity <avi@redhat.com>

The host shadow mmu code needs to get initialized. It needs to fetch a
segment it can use to put shadow PTEs into.

That initialization code was in generic code, which is icky. Let's move
it over to the respective MMU file.
Signed-off-by: NAlexander Graf <agraf@suse.de>
Signed-off-by: NAvi Kivity <avi@redhat.com>

We already have some inline fuctions we use to access vcpu or svcpu structs,
depending on whether we're on booke or book3s. Since we just put a few more
registers into the svcpu, we also need to make sure the respective callbacks
are available and get used.

So this patch moves direct use of the now in the svcpu struct fields to
inline function calls. While at it, it also moves the definition of those
inline function calls to respective header files for booke and book3s,
greatly improving readability.
Signed-off-by: NAlexander Graf <agraf@suse.de>
Signed-off-by: NAvi Kivity <avi@redhat.com>

Cell can't handle MSR_FE0 and MSR_FE1 too well. It gets dog slow.
So let's just override the guest whenever we see one of the two and mask them
out. See commit ddf5f75a for reference.
Signed-off-by: NAlexander Graf <agraf@suse.de>
Signed-off-by: NAvi Kivity <avi@redhat.com>

On most systems we need to emulate dcbz when running 32 bit guests. So
far we've been rather slack, not giving correct DSISR values to the guest.

This patch makes the emulation more accurate, introducing a difference
between "page not mapped" and "write protection fault". While at it, it
also speeds up dcbz emulation by an order of magnitude by using kmap.
Signed-off-by: NAlexander Graf <agraf@suse.de>
Signed-off-by: NAvi Kivity <avi@redhat.com>

The FPU/Altivec/VSX enablement also brought access to some structure
elements that are only defined when the respective config options
are enabled.

Unfortuately I forgot to check for the config options at some places,
so let's do that now.

Unbreaks the build when CONFIG_VSX is not set.
Signed-off-by: NAlexander Graf <agraf@suse.de>
Signed-off-by: NAvi Kivity <avi@redhat.com>

MOL uses its own hypercall interface to call back into userspace when
the guest wants to do something.

So let's implement that as an exit reason, specify it with a CAP and
only really use it when userspace wants us to.

The only user of it so far is MOL.
Signed-off-by: NAlexander Graf <agraf@suse.de>
Signed-off-by: NAvi Kivity <avi@redhat.com>

Mac OS X has some applications - namely the Finder - that require alignment
interrupts to work properly. So we need to implement them.

But the spec for 970 and 750 also looks different. While 750 requires the
DSISR and DAR fields to reflect some instruction bits (DSISR) and the fault
address (DAR), the 970 declares this as an optional feature. So we need
to reconstruct DSISR and DAR manually.
Signed-off-by: NAlexander Graf <agraf@suse.de>
Signed-off-by: NAvi Kivity <avi@redhat.com>

When trying to read or store vcpu register data, we should also make
sure the vcpu is actually loaded, so we're 100% sure we get the correct
values.
Signed-off-by: NAlexander Graf <agraf@suse.de>
Signed-off-by: NAvi Kivity <avi@redhat.com>

When the guest activates the FPU, we load it up. That's fine when
it wasn't activated before on the host, but if it was we end up
reloading FPU values from last time the FPU was deactivated on the
host without writing the proper values back to the vcpu struct.

This patch checks if the FPU is enabled already and if so just doesn't
bother activating it, making FPU operations survive guest context switches.
Signed-off-by: NAlexander Graf <agraf@suse.de>
Signed-off-by: NAvi Kivity <avi@redhat.com>