Migrate to using functionally-reduced I2C master contained in the DWC
HDMI. Therefore drop the GPIO bitbanging based i2cddc definition and
modify resp. pinctrl.

While at it re-order the I2C aliases to start with the generic, followed
by the camera and concluded by the power I2C one.
Signed-off-by: NMarcel Ziswiler <marcel.ziswiler@toradex.com>
Signed-off-by: NShawn Guo <shawnguo@kernel.org>

Signed-off-by: NMarcel Ziswiler <marcel.ziswiler@toradex.com>
Signed-off-by: NShawn Guo <shawnguo@kernel.org>

Signed-off-by: NMarcel Ziswiler <marcel.ziswiler@toradex.com>
Signed-off-by: NShawn Guo <shawnguo@kernel.org>

Signed-off-by: NMarcel Ziswiler <marcel.ziswiler@toradex.com>
Signed-off-by: NShawn Guo <shawnguo@kernel.org>

Signed-off-by: NMarcel Ziswiler <marcel.ziswiler@toradex.com>
Signed-off-by: NShawn Guo <shawnguo@kernel.org>

Signed-off-by: NMarcel Ziswiler <marcel.ziswiler@toradex.com>
Signed-off-by: NShawn Guo <shawnguo@kernel.org>

Split the pinctrl property for usdhc1 into a 4-bit SD interface
and an extension to 8-bit. This is required to support both 8-bit
and 4-bit interface on usdhc1 as per the carrier board.
Signed-off-by: NSanchayan Maity <maitysanchayan@gmail.com>
Signed-off-by: NShawn Guo <shawnguo@kernel.org>

The SD1 pinctrl-0 property is overridden but only the card detect pin
is muxed, the control and data signals are not referenced at all.
It worked because the bootloader muxed them to a sensible state though.
Fix this.
Signed-off-by: NSanchayan Maity <maitysanchayan@gmail.com>
Signed-off-by: NShawn Guo <shawnguo@kernel.org>

Support proper system power-off, which disables main regulator. This
results in much lower power consumption and support of power-on issued
by button press.
Signed-off-by: NMarcin Niestroj <m.niestroj@grinn-global.com>
Signed-off-by: NShawn Guo <shawnguo@kernel.org>

The CX9020 differs from i.MX53 Quick Start Board by:
- use uart2 instead of uart1
- DVI-D connector instead of VGA
- no audio
- no SATA connector
- CCAT FPGA connected to emi
- enable rtc
Signed-off-by: NPatrick Bruenn <p.bruenn@beckhoff.com>
Signed-off-by: NShawn Guo <shawnguo@kernel.org>

UART2 on EIM_D26 - EIM_D29 pins supports interchanging RXD/TXD pins
and RTS/CTS pins.
One board using these alternate settings is Beckhoff CX9020. Add the
alternative configuration here, to make it available to others, too.
Signed-off-by: NPatrick Bruenn <p.bruenn@beckhoff.com>
Signed-off-by: NShawn Guo <shawnguo@kernel.org>

The i.MX53 has an integrated secure real time clock. Add it to the dtsi.
Signed-off-by: NPatrick Bruenn <p.bruenn@beckhoff.com>
Signed-off-by: NShawn Guo <shawnguo@kernel.org>

Add a devicetree entry for the Random Number Generator Version B (RNGB).
The driver for RNGC supports version B as well.
Signed-off-by: NSteffen Trumtrar <s.trumtrar@pengutronix.de>
Signed-off-by: NMartin Kaiser <martin@kaiser.cx>
Signed-off-by: NShawn Guo <shawnguo@kernel.org>

MX6UL_PAD_SNVS_TAMPER0__GPIO5_IO00 is connected to the INT1 pin of
the FXLS8471Q accelerometer, so remove it from the unrelated ENET
group.
Signed-off-by: NFabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: NShawn Guo <shawnguo@kernel.org>

Add support for Flexcan.
Signed-off-by: NFabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: NShawn Guo <shawnguo@kernel.org>

The Colibri iMX7 modules come with 512MB on-module SLC NAND flash
populated. Make use of it by enabling the GPMI controller.
Signed-off-by: NStefan Agner <stefan@agner.ch>
Tested-by: NFabio Estevam <fabio.estevam@nxp.com>
Acked-by: NHan Xu <han.xu@nxp.com>
Signed-off-by: NShawn Guo <shawnguo@kernel.org>

Add i.MX 7 APBH DMA and GPMI NAND modules.
Signed-off-by: NStefan Agner <stefan@agner.ch>
Tested-by: NFabio Estevam <fabio.estevam@nxp.com>
Acked-by: NHan Xu <han.xu@nxp.com>
Signed-off-by: NShawn Guo <shawnguo@kernel.org>

Declared as a regulator since the driver doesn't have a reset-gpios
property for this.

This ensures that the PHY is woken up, not depending on the state the
second stage bootloader leaves the pin.

This is a workaround until a proper mechanism is provided to reset such
devices like the pwrseq library [1] for instance.

[1] https://lkml.org/lkml/2017/2/10/779Signed-off-by: NGary Bisson <gary.bisson@boundarydevices.com>
Reviewed-by: NFabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: NShawn Guo <shawnguo@kernel.org>

Declared as a regulator since the driver doesn't have a reset-gpios
property for this.

This ensures that the PHY is woken up, not depending on the state the
second stage bootloader leaves the pin.

This is a workaround until a proper mechanism is provided to reset such
devices like the pwrseq library [1] for instance.

[1] https://lkml.org/lkml/2017/2/10/779Signed-off-by: NGary Bisson <gary.bisson@boundarydevices.com>
Reviewed-by: NFabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: NShawn Guo <shawnguo@kernel.org>

gpio-line-names may help to make work with GPIOs from user space easier.
Following examples are provided with libgpiod
https://github.com/brgl/libgpiod :
|# Toggle a GPIO by name, then wait for the user to press ENTER.
|$ gpioset --mode=wait `gpiofind "USR-LED-2"`=1
|# Pause execution until a single event of any type occurs. Don't print
|# anything. Find the line by name.
|$ gpiomon --num-events=1 --silent `gpiofind "USR-IN"`

Used names was taken from RIoTboard schematics, version 1 (2013.12.07).
Signed-off-by: NOleksij Rempel <o.rempel@pengutronix.de>
Signed-off-by: NShawn Guo <shawnguo@kernel.org>

The Micrel PHY has its interrupt pin connected to a GPIO line. Wire
this up in the device tree.
Signed-off-by: NAndrew Lunn <andrew@lunn.ch>
Tested-by: NChris Healy <cphealy@gmail.com>
Reviewed-by: NFabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: NShawn Guo <shawnguo@kernel.org>

The Marvell switch has its interrupt pin connected to a GPIO
line. Wire this up in the device tree. This then allows us to use
interrupts from the embedded Ethernet PHYs in the switch. Also wire
them up in device tree.
Signed-off-by: NAndrew Lunn <andrew@lunn.ch>
Tested-by: NChris Healy <cphealy@gmail.com>
Reviewed-by: NFabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: NShawn Guo <shawnguo@kernel.org>

The Marvell switch has an EEPROM connected to it. List the size in DT,
in order to enable access to it via ethtool.
Signed-off-by: NAndrew Lunn <andrew@lunn.ch>
Tested-by: NChris Healy <cphealy@gmail.com>
Reviewed-by: NFabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: NShawn Guo <shawnguo@kernel.org>

The RDU2 has a Marvell 88E6352 switch. Both the FEC and the i210
Ethernet interfaces are connected to the switch. Make the FEC the DSA
"CPU" port, and the i210 as a regular port on the switch.
Signed-off-by: NAndrew Lunn <andrew@lunn.ch>
Tested-by: NChris Healy <cphealy@gmail.com>
Reviewed-by: NFabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: NShawn Guo <shawnguo@kernel.org>

The FEC has a Micrel PHY connected to it. This PHY is managed using
the bit-banging MDIO bus. Add this to the device tree.
Signed-off-by: NAndrew Lunn <andrew@lunn.ch>
Tested-by: NChris Healy <cphealy@gmail.com>
Reviewed-by: NFabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: NShawn Guo <shawnguo@kernel.org>

Currently the LCD is turned on thanks to the bootloader initialization.

In order to make the kernel to turn on the LCD on is own, pass the
'enable-gpios' and 'power-supply' properties.

Also, the GPIO1_IO01 is not used as PWM functionality on this board. It is
connected to the PWREN pin of connector J14 and has a GPIO function, so
remove the PWM1 node and change the GPIO1_IO01 IOMUX to GPIO function.
Signed-off-by: NMarco Franchi <marco.franchi@nxp.com>
Signed-off-by: NShawn Guo <shawnguo@kernel.org>

It is preferred to use the panel compatible string rather than passing the
LCD timming in the device tree.

So pass the "innolux,at043tn24" compatible string to describe the parallel
LCD on this board.
Signed-off-by: NMarco Franchi <marco.franchi@nxp.com>
Signed-off-by: NShawn Guo <shawnguo@kernel.org>

The 'uart-has-rtscts' property should be used when the board exposes the
native RTS and CTS UART pins.

On the imx6qdl-gw5xxx boards such pins are not used, so remove the
'uart-has-rtscts' property to make the hardware description correct.

Documentation/devicetree/bindings/serial/serial.txt states that
'uart-has-rtscts' and 'rts-gpios' properties are mutually exclusive.
Signed-off-by: NFabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: NShawn Guo <shawnguo@kernel.org>

Pass the 'backlight' property as described in
Documentation/devicetree/bindings/display/panel/simple-panel.txt
Signed-off-by: NMarco Franchi <marco.franchi@nxp.com>
Signed-off-by: NShawn Guo <shawnguo@kernel.org>

It is preferred to use the panel compatible string rather than passing the LCD
timming in the device tree.

So pass the "innolux,at043tn24" compatible string to describe the parallel LCD
on this board.
Signed-off-by: NMarco Franchi <marco.franchi@nxp.com>
Signed-off-by: NShawn Guo <shawnguo@kernel.org>

Make the syscon-poweroff driver change only the shutdown bits on the
SNVS_LP control register.

This change fixes an issue with the RTC wakeup alarm, that was
previously disabled during power off.
Signed-off-by: NGuy Shapiro <guy.shapiro@mobi-wize.com>
Reviewed-by: NMarcin Niestroj <m.niestroj@grinn-global.com>
Reviewed-by: NFabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: NShawn Guo <shawnguo@kernel.org>

imx6qdl-icore-rqs boards use sgtl5000 codec and the machine
file (imx-sgtl5000) already sets SSI in slave mode and codec in
master mode, so there is no need for having this property.
Signed-off-by: NFabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: NShawn Guo <shawnguo@kernel.org>

Pass the phy-reset-gpios property so that Ethernet PHYs can go
through a proper reset.
Signed-off-by: NFabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: NShawn Guo <shawnguo@kernel.org>

The IPU that drives HDMI must have its pre_sel set to pll2_pfd_396m
to avoid stepping on the LVDS output's toes, as the PLL can't be clocked
to the pixel clock and to the LVDS serial clock (3.5*pixel clock) at the
same time.

As we are using ipu1_di0 and ipu2_di0, ensure both are switched to
to pll2_pfd2_396m to avoid issues. The LDB driver will switch the
required IPU to ldb_di1 when it uses it to drive LVDS.
Signed-off-by: NMartyn Welch <martyn.welch@collabora.co.uk>
Signed-off-by: NRomain Perier <romain.perier@collabora.com>
Reviewed-by: NFabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: NShawn Guo <shawnguo@kernel.org>

According to mx7sabresd schematics the MIPI CSI/DSI voltage rails
should be 2.8V but the voltage provided is a maximum of 3.3V and
minimum of 1.8V. Providing such a higher voltage might damage the
peripherals and violates the schematic settings.
Signed-off-by: NGautam Bhat <mindentropy@gmail.com>
Reviewed-by: NFabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: NShawn Guo <shawnguo@kernel.org>

Enables the ADV7180 analog video decoder sensor connected to the
IMX6 IPU on various Gateworks Ventana boards.
Signed-off-by: NTim Harvey <tharvey@gateworks.com>
Signed-off-by: NShawn Guo <shawnguo@kernel.org>

Add support for Sound card and related codec(via i2c1) nodes
on Engicam GEAM6UL variant module boards.
Signed-off-by: NJagan Teki <jagan@amarulasolutions.com>
Signed-off-by: NShawn Guo <shawnguo@kernel.org>

Engicam SOM's with mounted on starter kits like icorem6(rqs), isiot
usually not explicitly named with -kit in dts file names and
instead Model has mentioned 'Starter kit' So apply the same rule
for geam SOM as well.
Signed-off-by: NJagan Teki <jagan@amarulasolutions.com>
Signed-off-by: NShawn Guo <shawnguo@kernel.org>

GEAM6UL SOM does have single module, it doesn't come with
any variants. Maintaining imx6ul-geam.dtsi make no sense
so move all devices from .dtsi into dts file and drop the same.
Signed-off-by: NJagan Teki <jagan@amarulasolutions.com>
Signed-off-by: NShawn Guo <shawnguo@kernel.org>

usdhc1 is enabled and assigned pinctrl-0 on imx6ul-geam.dtsi
but same thing done on imx6ul-geam-kit.dts, so remove this
re-enabled node from the same.
Signed-off-by: NJagan Teki <jagan@amarulasolutions.com>
Signed-off-by: NShawn Guo <shawnguo@kernel.org>