When FW notify driver or driver detects low FW resource,
driver tries to send out Busy SCSI Status to tell Initiator
side to back off. During the send process, the lock was not held.

Cc: <stable@vger.kernel.org>
Signed-off-by: NQuinn Tran <quinn.tran@qlogic.com>
Signed-off-by: NHimanshu Madhani <himanshu.madhani@cavium.com>
Signed-off-by: NNicholas Bellinger <nab@linux-iscsi.org>

Cc: <stable@vger.kernel.org>
Signed-off-by: NQuinn Tran <quinn.tran@cavium.com>
Signed-off-by: NHimanshu Madhani <himanshu.madhani@cavium.com>
Signed-off-by: NNicholas Bellinger <nab@linux-iscsi.org>

This patch simplifies SRB structure usage in driver.

- Simplify sp->done() and sp->free() interfaces.
- Remove sp->fcport->vha to use vha pointer from sp.
- Use sp->vha context in qla2x00_rel_sp().
Signed-off-by: NJoe Carnuccio <joe.carnuccio@cavium.com>
Signed-off-by: NHimanshu Madhani <himanshu.madhani@cavium.com>
Signed-off-by: NBart Van Assche <bart.vanassche@sandisk.com>
Signed-off-by: NNicholas Bellinger <nab@linux-iscsi.org>

Current code blindly does State Change Registration when
the link is up. Move SCR behind fabric scan, so that arbitrated
loop scan would not get erroneous error message.

Some of the other improvements are as follows

- Add session deletion for TPRLO and send acknowledgment for TPRLO.
- Enable FW option to move ABTS, RIDA & PUREX from RSPQ to ATIOQ.
- Save NPort ID early in link init.
- Move ABTS & RIDA to ATIOQ helps in keeping command ordering and
  link up sequence ordering.
- Save Nport ID and update VP map so that SCSI CMD/ATIO won't be dropped.
- fcport alloc does the initializes memory to zero. Remove memset to
  zero since It might corrupt link list.
- Turn off Registration for State Change MB in loop mode.
Signed-off-by: NQuinn Tran <quinn.tran@cavium.com>
Signed-off-by: NHimanshu Madhani <himanshu.madhani@cavium.com>
Signed-off-by: NBart Van Assche <bart.vanassche@sandisk.com>
Signed-off-by: NNicholas Bellinger <nab@linux-iscsi.org>

With support for dual mode in the driver, this mode becomes
dead code. Remove reverse_ini_mode from code.
Signed-off-by: NHimanshu Madhani <himanshu.madhani@cavium.com>
Signed-off-by: NBart Van Assche <bart.vanassche@sandisk.com>
Signed-off-by: NNicholas Bellinger <nab@linux-iscsi.org>

Add switch to allow both Initiator Mode & Target
mode to operate at the same time.
Signed-off-by: NQuinn Tran <quinn.tran@cavium.com>
Signed-off-by: NHimanshu Madhani <himanshu.madhani@cavium.com>
Signed-off-by: NBart Van Assche <bart.vanassche@sandisk.com>
Signed-off-by: NNicholas Bellinger <nab@linux-iscsi.org>

Currently code performs a full scan of the fabric for
every RSCN. Its an expensive process in a noisy large SAN.

This patch optimizes expensive fabric discovery process by
scanning switch for the affected port when RSCN is received.

Currently Initiator Mode code makes login/logout decision without
knowledge of target mode. This causes driver and firmware to go
out-of-sync. This framework synchronizes both initiator mode
personality and target mode personality in making login/logout
decision.

This patch adds following capabilities in the driver

- Send Notification Acknowledgement asynchronously.
- Update session/fcport state asynchronously.
- Create a session or fcport struct asynchronously.
- Send GNL asynchronously. The command will ask FW to
  provide a list of FC Port entries FW knows about.
- Send GPDB asynchronously. The command will ask FW to
  provide detail data of an FC Port FW knows about or
  perform ADISC to verify the state of the session.
- Send GPNID asynchronously. The command will ask switch
  to provide WWPN for provided NPort ID.
- Send GPSC asynchronously. The command will ask switch
  to provide registered port speed for provided WWPN.
- Send GIDPN asynchronously. The command will ask the
  switch to provide Nport ID for provided WWPN.
- In driver unload path, schedule all session for deletion
  and wait for deletion to complete before allowing driver
  unload to proceed.
Signed-off-by: NQuinn Tran <quinn.tran@cavium.com>
Signed-off-by: NHimanshu Madhani <himanshu.madhani@cavium.com>
[ bvanassche: fixed spelling in patch description ]
Signed-off-by: NBart Van Assche <bart.vanassche@sandisk.com>
Signed-off-by: NNicholas Bellinger <nab@linux-iscsi.org>

Current code merges qla_tgt_sess and fc_port structure
into single fc_port structure representing same I-T nexus.
Signed-off-by: NQuinn Tran <quinn.tran@cavium.com>
Signed-off-by: NHimanshu Madhani <himanshu.madhani@cavium.com>
[ bvanassche: fixed spelling of patch description ]
Signed-off-by: NBart Van Assche <bart.vanassche@sandisk.com>
Signed-off-by: NNicholas Bellinger <nab@linux-iscsi.org>

Updated code with d_id from s_id for better readability and
clarity.
Signed-off-by: NQuinn Tran <quinn.tran@cavium.com>
Signed-off-by: NHimanshu Madhani <himanshu.madhani@cavium.com>
Reviewed-by: NChristoph Hellwig <hch@lst.de>
[ bvanassche: fixed spelling of patch description ]
Signed-off-by: NBart Van Assche <bart.vanassche@sandisk.com>
Signed-off-by: NNicholas Bellinger <nab@linux-iscsi.org>

During initial implementation, tape support was included but not
enabled by default on target. So far, we don't see any target
customer requesting this support. Since this code is not being
used actively, we want to remove it and we will add back if there
are any request in future for SRR support.
Signed-off-by: NHimanshu Madhani <himanshu.madhani@cavium.com>
Signed-off-by: NGiridhar Malavali <giridhar.malavali@cavium.com>
Reviewed-by: NChristoph Hellwig <hch@lst.de>
Signed-off-by: NBart Van Assche <bart.vanassche@sandisk.com>
Signed-off-by: NNicholas Bellinger <nab@linux-iscsi.org>

Trace flags are useful during debugging crash dumps
using crash utility. These trace flags makes it easier
to understand various states a command has successfully
completed.
Signed-off-by: NQuinn Tran <quinn.tran@cavium.com>
Signed-off-by: NHimanshu Madhani <himanshu.madhani@cavium.com>
Signed-off-by: NBart Van Assche <bart.vanassche@sandisk.com>
Signed-off-by: NNicholas Bellinger <nab@linux-iscsi.org>

Move code code which converts Task Mgmt Command flags for
ATIO to TCM #defines, from qla2xxx driver to tcm_qla2xxx
driver.
Signed-off-by: NQuinn Tran <quinn.tran@cavium.com>
Signed-off-by: NHimanshu Madhani <himanshu.madhani@cavium.com>
Reviewed-by: NChristoph Hellwig <hch@lst.de>
Signed-off-by: NBart Van Assche <bart.vanassche@sandisk.com>
Signed-off-by: NNicholas Bellinger <nab@linux-iscsi.org>

Signed-off-by: NQuinn Tran <quinn.tran@cavium.com>
Signed-off-by: NHimanshu Madhani <himanshu.madhani@cavium.com>
Reviewed-by: NChristoph Hellwig <hch@lst.de>
Signed-off-by: NBart Van Assche <bart.vanassche@sandisk.com>
Signed-off-by: NNicholas Bellinger <nab@linux-iscsi.org>

Out of order(OOO) processing requires initiator, switch
and target to support OOO. In today's environment, none
of the switches support OOO. OOO requires extra buffer
space which affect performance. By turning ON this feature
in QLogic's FW, it delays error recovery because dropped
frame is treated as out of order frame. We're turning OFF
this option of speed up error recovery.
Signed-off-by: NQuinn Tran <quinn.tran@cavium.com>
Signed-off-by: NHimanshu Madhani <himanshu.madhani@cavium.com>
Reviewed-by: NChristoph Hellwig <hch@lst.de>
[ bvanassche: Fixed spelling in patch description ]
Signed-off-by: NBart Van Assche <bart.vanassche@sandisk.com>

Termination of Immediate Notify IOCB was using wrong
IOCB handle. IOCB completion code was unable to find
appropriate code path due to wrong handle.

Following message is seen in the logs.

"Error entry - invalid handle/queue (ffff)."
Signed-off-by: NQuinn Tran <quinn.tran@cavium.com>
Signed-off-by: NHimanshu Madhani <himanshu.madhani@cavium.com>
Reviewed-by: NChristoph Hellwig <hch@lst.de>
[ bvanassche: Fixed word order in patch title ]
Signed-off-by: NBart Van Assche <bart.vanassche@sandisk.com>

Corrupted ATIO is defined as length of fcp_header & fcp_cmd
payload is less than 0x38. It's the minimum size for a frame to
carry 8..16 bytes SCSI CDB. The exchange will be dropped or
terminated if corrupted.
Signed-off-by: NQuinn Tran <quinn.tran@cavium.com>
Signed-off-by: NHimanshu Madhani <himanshu.madhani@cavium.com>
Reviewed-by: NChristoph Hellwig <hch@lst.de>
[ bvanassche: Fixed spelling in patch title ]
Signed-off-by: NBart Van Assche <bart.vanassche@sandisk.com>

During NVRAM initialization in target mode, reset reserved
fields in firmware options to Zero (BIT 15)
Signed-off-by: NHimanshu Madhani <himanshu.madhani@cavium.com>
Signed-off-by: NGiridhar Malavali <giridhar.malavali@cavium.com>
Reviewed-by: NChristoph Hellwig <hch@lst.de>
Signed-off-by: NBart Van Assche <bart.vanassche@sandisk.com>

qlt_reset is called with Immedidate Notify IOCB only.
Current code wrongly cast it as ATIO IOCB.
Signed-off-by: NQuinn Tran <quinn.tran@cavium.com>
Signed-off-by: NHimanshu Madhani <himanshu.madhani@cavium.com>
Reviewed-by: NChristoph Hellwig <hch@lst.de>
Signed-off-by: NBart Van Assche <bart.vanassche@sandisk.com>

Remove two set-but-not-used variables and avoid that the compiler
warns about a third variable (rc).
Signed-off-by: NBart Van Assche <bart.vanassche@sandisk.com>
Acked-by: NHimanshu Madhani <himanshu.madhani@qlogic.com>
Cc: Quinn Tran <quinn.tran@qlogic.com>
Cc: Christoph Hellwig <hch@lst.de>

Properly initialize IO statistics to avoid initial 0xFFFFFFF (-1) values.

Cleanup/simplify usage of pointer to statistics structure.
Signed-off-by: NJoe Carnuccio <joe.carnuccio@qlogic.com>
Signed-off-by: NHimanshu Madhani <himanshu.madhani@qlogic.com>
Reviewed-by: NHannes Reinecke <hare@suse.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

This stops abusing the common sess_kref to overload it for private
usage, which allows removing the shutdown_session method as well.
Signed-off-by: NChristoph Hellwig <hch@lst.de>
Signed-off-by: NNicholas Bellinger <nab@linux-iscsi.org>

The qlt_check_reserve_free_req() function produces an incorrect warning
when CONFIG_PROFILE_ANNOTATED_BRANCHES is set:

drivers/scsi/qla2xxx/qla_target.c: In function 'qlt_check_reserve_free_req':
drivers/scsi/qla2xxx/qla_target.c:1887:3: error: 'cnt_in' may be used uninitialized in this function [-Werror=maybe-uninitialized]
   ql_dbg(ql_dbg_io, vha, 0x305a,
   ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
       "qla_target(%d): There is no room in the request ring: vha->req->ring_index=%d, vha->req->cnt=%d, req_cnt=%d Req-out=%d Req-in=%d Req-Length=%d\n",
       ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
       vha->vp_idx, vha->req->ring_index,
       ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
       vha->req->cnt, req_cnt, cnt, cnt_in, vha->req->length);
       ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
drivers/scsi/qla2xxx/qla_target.c:1887:3: error: 'cnt' may be used uninitialized in this function [-Werror=maybe-uninitialized]

The problem is that gcc fails to track the state of the condition across
an annotated branch.

This slightly rearranges the code to move the second if() block
into the first one, to avoid the warning while retaining the
behavior of the code.
Signed-off-by: NArnd Bergmann <arnd@arndb.de>
Acked-By: NHimanshu Madhani <himanshu.madhani@qlogic.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

 #cat  /sys/kernel/debug/qla2xxx/qla2xxx_31/tgt_sess
 qla2xxx_31
 Port ID   Port Name                Handle
 ff:fc:01  21:fd:00:05:33:c7:ec:16  0
 01:0e:00  21:00:00:24:ff:7b:8a:e4  1
 01:0f:00  21:00:00:24:ff:7b:8a:e5  2
 ....

(Drop ->check_initiator_node_acl() parameter usage - nab)
Signed-off-by: NQuinn Tran <quinn.tran@qlogic.com>
Signed-off-by: NHimanshu Madhani <himanshu.madhani@qlogic.com>
Signed-off-by: NNicholas Bellinger <nab@linux-iscsi.org>

This patch converts existing qla2xxx target mode assignment
of struct qla_tgt_sess related sid + loop_id values to use
a callback via the new target_alloc_session API caller.

Cc: Himanshu Madhani <himanshu.madhani@qlogic.com>
Cc: Quinn Tran <quinn.tran@qlogic.com>
Cc: Giridhar Malavali <giridhar.malavali@qlogic.com>
Signed-off-by: NNicholas Bellinger <nab@linux-iscsi.org>

Signed-off-by: NQuinn Tran <quinn.tran@qlogic.com>
Reviewed-by: NChristoph Hellwig <hch@lst.de>
Reviewed-by: NBart Van Assche <bart.vanassche@sandisk.com>
Fixes: fb3269ba ("qla2xxx: Add selective command queuing")
Signed-off-by: NHimanshu Madhani <himanshu.madhani@qlogic.com>
Signed-off-by: NNicholas Bellinger <nab@linux-iscsi.org>

The function value inside se_cmd can change if the TMR is cancelled.
Use original ATIO Type to correctly determine CTIO response.
Signed-off-by: NSwapnil Nagle <swapnil.nagle@purestroage.com>
Signed-off-by: NHimanshu Madhani <himanshu.madhani@qlogic.com>
Signed-off-by: NNicholas Bellinger <nab@linux-iscsi.org>

During lun reset, TMR thread from TCM would issue abort
to qla driver.  At abort time, each command is in different
state.  Depending on the state, qla will use the TMR thread
to trigger a command free(cmd_kref--) if command is not
down at firmware.
Signed-off-by: NQuinn Tran <quinn.tran@qlogic.com>
Signed-off-by: NHimanshu Madhani <himanshu.madhani@qlogic.com>
Cc: stable@vger.kernel.org # 3.10+
Signed-off-by: NNicholas Bellinger <nab@linux-iscsi.org>

This patch fixes following warning

drivers/scsi/qla2xxx/qla_target.c:3587 qlt_do_ctio_completion()
warn: impossible condition '(logged_out == 41) => (0-1 == 41)'

drivers/scsi/qla2xxx/qla_target.c
 3580                  case CTIO_PORT_LOGGED_OUT:
 3581                  case CTIO_PORT_UNAVAILABLE:
 3582                  {
 3583                          bool logged_out = (status & 0xFFFF);
 3584                          ql_dbg(ql_dbg_tgt_mgt, vha, 0xf059,
 3585                              "qla_target(%d): CTIO with %s status %x "
 3586                              "received (state %x, se_cmd %p)\n", vha->vp_idx,
 3587                              (logged_out == CTIO_PORT_LOGGED_OUT) ?
                                    ^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^
                                    Bool cannot equal 0x26.
 3588                              "PORT LOGGED OUT" : "PORT UNAVAILABLE",
Reported-by: NDan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: NHimanshu Madhani <himanshu.madhani@qlogic.com>
Signed-off-by: NGiridhar Malavali <giridhar.malavali@qlogic.com>
Signed-off-by: NNicholas Bellinger <nab@linux-iscsi.org>

A recent bug fix added code that does

        bool logged_out = (status & 0xFFFF);
        if (logged_out == CTIO_PORT_LOGGED_OUT)
		...

This looks wrong because we are comparing a boolean with an
integer constant, ang gcc warns about it accordingly:

drivers/scsi/qla2xxx/qla_target.c: In function 'qlt_do_ctio_completion':
drivers/scsi/qla2xxx/qla_target.c:3587:20: warning: comparison of constant '41' with boolean expression is always false [-Wbool-compare]
        (logged_out == CTIO_PORT_LOGGED_OUT) ?

The correct fix is presumably to make that variable an 'int'.
Signed-off-by: NArnd Bergmann <arnd@arndb.de>
Fixes: 71cdc079 ("qla2xxx: Delete session if initiator is gone from FW")
Signed-off-by: NNicholas Bellinger <nab@linux-iscsi.org>

Driver has following initialization sequence for Target mode

1. Driver initialization starts

2. ISP Abort is scheduled when the target is enabled.

qla2xxx [0000:04:00.0]-4807:25: ISP abort scheduled
qla2xxx [0000:04:00.0]-00af:25: Performing ISP error recovery - ha=ffff880caa9e0000.

3. DPC thread starts the ISP Abort

4. While DPC is resetting the chip and initializing the firmware, we get
   async events from the firmware about P2P mode, LOOP UP and PORT UPDATE.

5. PRLI from a initiator is delivered to us followed by a PLOGI and then a
   SCSI command which creates a session.

6. If the SCSI command is a WRITE in this case, we issue XFR RDY and it
   gets dropped as can be seen with messages RESET-XFR because ISP Abort
   is still active

qla2xxx [0000:04:00.0]-e902:25: RESET-XFR active/old-count/new-count = 1/1/1.

7. If the SCSI command is a READ, we issue RESPONSE and they get dropped
   as well because Abort is still active.

qla2xxx [0000:04:00.0]-e901:25: RESET-RSP active/old-count/new-count = 1/1/1

8. Now eventually, ISP Abort finishes clearing the DPC flags.

qla2xxx [0000:04:00.0]-8822:25: qla2x00_abort_isp succeeded.
qla2xxx [0000:04:00.0]-4808:25: ISP abort end.

9. Since we dropped SCSI commands silently (without any responses sent
   to the initiator) initiator waits for a SCSI timeout (which is 60
   seconds in our case), Sends an ABTS which fails since there
   no se_cmd found for the tag that ABTS is referencing as the
   commands were cleaned up in Step 6 and 7.

10. Initiator send an IO after the ABTS which succeed fine.

To fix the above case, the following changes have been made:
  - To prevent target from dropping commands silently, use the online flag
    instead to check for an active chip reset. Once the port is online during
    a chip reset phase, we are good to process the commands.
  - Clean up qla2x00_restart_isp to not set the online flag and process ATIO
    as it is unnecessary. During a chip reset, interrupts are enabled only
    after setting the online flag to 1, so ATIO's won't be missed and hence
    no need to process ATIO's after setting the online flag.
Signed-off-by: NDilip Kumar Uppugandla <dilip@purestorage.com>
Signed-off-by: NHimanshu Madhani <himanshu.madhani@qlogic.com>
Signed-off-by: NNicholas Bellinger <nab@linux-iscsi.org>

Signed-off-by: NQuinn Tran <quinn.tran@qlogic.com>
Signed-off-by: NHimanshu Madhani <himanshu.madhani@qlogic.com>
Signed-off-by: NNicholas Bellinger <nab@linux-iscsi.org>

99% of the time the ATIOQ has SCSI command.  The other 1% of time
is something else.  Most of the time this interrupt does not need
to hold the hardware_lock.  We're moving the ATIO interrupt thread
to a different lock to reduce lock contention.
Signed-off-by: NQuinn Tran <quinn.tran@qlogic.com>
Signed-off-by: NHimanshu Madhani <himanshu.madhani@qlogic.com>
Signed-off-by: NNicholas Bellinger <nab@linux-iscsi.org>

queue work element to specific process lessen cache miss
Signed-off-by: NQuinn Tran <quinn.tran@qlogic.com>
Signed-off-by: NHimanshu Madhani <himanshu.madhani@qlogic.com>
Signed-off-by: NNicholas Bellinger <nab@linux-iscsi.org>

Register to receive notification of when irq setting change
occured.
Signed-off-by: NQuinn Tran <quinn.tran@qlogic.com>
Signed-off-by: NHimanshu Madhani <himanshu.madhani@qlogic.com>
Signed-off-by: NNicholas Bellinger <nab@linux-iscsi.org>

Sessions management (add, deleted, modify) currently are serialized
through the hardware_lock.  Hardware_lock is a high traffic lock.
This lock is accessed by both the transmit & receive sides.

Sessions management is now moved off to another lock call sess_lock.
This is done to reduce lock contention and increase traffic throughput.
Signed-off-by: NQuinn Tran <quinn.tran@qlogic.com>
Signed-off-by: NHimanshu Madhani <himanshu.madhani@qlogic.com>
Signed-off-by: NNicholas Bellinger <nab@linux-iscsi.org>

Replace QLA_TGT_STATE_ABORTED state with a bit because
the current state of the command is lost when an abort
is requested by upper layer.
Signed-off-by: NQuinn Tran <quinn.tran@qlogic.com>
Signed-off-by: NHimanshu Madhani <himanshu.madhani@qlogic.com>
Reviewed-by: NHannes Reinecke <hare@suse.com>
Signed-off-by: NNicholas Bellinger <nab@linux-iscsi.org>

Until now ack'ing of a new PLOGI has only been delayed if there
was an existing session for the same WWN. Ack was released when
the session deletion completed.

If there was another WWN session with the same fc_id/loop_id pair
(aka "conflicting session"), PLOGI was still ack'ed immediately.
This potentially caused a problem when old session deletion logged
fc_id/loop_id out of FW after new session has been established.

Two work-arounds were attempted before:
1. Dropping PLOGIs until conflicting session goes away.
2. Detecting initiator being logged out of FW and issuing LOGO
to force re-login.

This patch introduces proper solution to the problem where PLOGI
is held until either existing session with same WWN or any
conflicting session goes away. Mechanism supports one session holding
two PLOGI acks as well as one PLOGI ack being held by many sessions.
Signed-off-by: NAlexei Potashnik <alexei@purestorage.com>
Acked-by: NQuinn Tran <quinn.tran@qlogic.com>
Signed-off-by: NHimanshu Madhani <himanshu.madhani@qlogic.com>
Reviewed-by: NHannes Reinecke <hare@suse.com>
Signed-off-by: NNicholas Bellinger <nab@linux-iscsi.org>

1. Initiator A is logged in with fc_id(1)/loop_id(1)
2. Initiator A re-logs in with fc_id(2)/loop_id(2)
3. Part of old session deletion async logoout for 1/1 is queued
4. Initiator B logs in with fc_id(1)/loop_id(1), starts
   passing data and creates session.
5. Async logo from 3 is processed by DPC and sent to FW

Now initiator B has the session but is logged out from FW.

This condition is detected first with CTIO error 29 at which
point we should delete current session. During session
deletion we will send LOGO to initiator to force re-login.

Under rare circumstances initiator might be logged out of FW,
not have driver session, but still think it's logged in.
E.g. the above sequence plus session deletion due to re-config.
Incoming commands will fail to create local session because
initiator is not found in FW. In this case we also issue LOGO
to initiator to force him re-login.

Finally this patch fixes exchange leak when commands where
received in logged out state. In this case loop_id must be
set to FFFF when corresponding exchange is terminated. The
patch modifies exchange termination to always use FFFF,
since in certain scenarios it's impossible to tell whether
command was received in logged in or logged out state.
Signed-off-by: NAlexei Potashnik <alexei@purestorage.com>
Acked-by: NQuinn Tran <quinn.tran@qlogic.com>
Signed-off-by: NHimanshu Madhani <himanshu.madhani@qlogic.com>
Reviewed-by: NHannes Reinecke <hare@suse.com>
Signed-off-by: NNicholas Bellinger <nab@linux-iscsi.org>

DebugFS now will show fw_resource_count node.

FW Resource count

Original TGT exchg count[0]
current TGT exchg count[0]
original Initiator Exchange count[2048]
Current Initiator Exchange count[2048]
Original IOCB count[2078]
Current IOCB count[2067]
MAX VP count[254]
MAX FCF count[0]
Signed-off-by: NQuinn Tran <quinn.tran@qlogic.com>
Signed-off-by: NHimanshu Madhani <himanshu.madhani@qlogic.com>
Reviewed-by: NHannes Reinecke <hare@suse.com>
Signed-off-by: NNicholas Bellinger <nab@linux-iscsi.org>

Following counters are added in target mode to help debugging efforts.

Target Counters

qla_core_sbt_cmd = 0
qla_core_ret_sta_ctio = 0
qla_core_ret_ctio = 0
core_qla_que_buf = 0
core_qla_snd_status = 0
core_qla_free_cmd = 0
num alloc iocb failed = 0
num term exchange sent = 0
num Q full sent = 0
Signed-off-by: NHimanshu Madhani <himanshu.madhani@qlogic.com>
Signed-off-by: NGiridhar Malavali <giridhar.malavali@qlogic.com>
Reviewed-by: NHannes Reinecke <hare@suse.com>
Signed-off-by: NNicholas Bellinger <nab@linux-iscsi.org>