- 17 5月, 2011 2 次提交
-
-
由 Yogesh Ashok Powar 提交于
Currently the devices that have already stripped IEEE 802.11 header from the AMSDU SKB can not use ieee80211_amsdu_to_8023s routine. This patch enhances ieee80211_amsdu_to_8023s() API by changing mandatory removing of IEEE 802.11 header from AMSDU to optional. Signed-off-by: NYogesh Ashok Powar <yogeshp@marvell.com> Signed-off-by: NBing Zhao <bzhao@marvell.com> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Johannes Berg 提交于
Add the ability to advertise interface combinations in nl80211. This allows the driver to indicate what the combinations are that it supports. "Combinations" of just a single interface are implicit, as previously. Note that cfg80211 will enforce that the restrictions are met, but not for all drivers yet (once all drivers are updated, we can remove the flag and enforce for all). When no combinations are actually supported, an empty list will be exported so that userspace can know if the kernel exported this info or not (although it isn't clear to me what tools using the info should do if the kernel didn't export it). Since some interface types are purely virtual/software and don't fit the restrictions, those are exposed in a new list of pure SW types, not subject to restrictions. This mainly exists to handle AP-VLAN and monitor interfaces in mac80211. Signed-off-by: NJohannes Berg <johannes.berg@intel.com> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
- 13 5月, 2011 1 次提交
-
-
由 Johannes Berg 提交于
Multiple virtual AP interfaces can currently try to use different beacon intervals, but that just leads to problems since it won't actually be done that way by drivers. Return an error in this case to make sure it won't be done wrong. Also, ignore attempts to change the DTIM period or beacon interval during the lifetime of the BSS. Signed-off-by: NJohannes Berg <johannes.berg@intel.com> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
- 29 1月, 2011 1 次提交
-
-
由 Juuso Oikarinen 提交于
Some vendor specific cipher suites require non-zero key indexes for pairwise keys, but as of currently, the cfg80211 does not allow it. As validating they cipher parameters for vendor specific cipher suites is the job of the driver or hardware/firmware, change the cfg80211 to allow also non-zero pairwise key indexes for vendor specific ciphers. Signed-off-by: NJuuso Oikarinen <juuso.oikarinen@nokia.com> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
- 22 1月, 2011 1 次提交
-
-
由 Bruno Randolf 提交于
Extend channel to frequency mapping for 802.11j Japan 4.9GHz band, according to IEEE802.11 section 17.3.8.3.2 and Annex J. Because there are now overlapping channel numbers in the 2GHz and 5GHz band we can't map from channel to frequency without knowing the band. This is no problem as in most contexts we know the band. In places where we don't know the band (and WEXT compatibility) we assume the 2GHz band for channels below 14. This patch does not implement all channel to frequency mappings defined in 802.11, it's just an extension for 802.11j 20MHz channels. 5MHz and 10MHz channels as well as 802.11y channels have been omitted. The following drivers have been updated to reflect the API changes: iwl-3945, iwl-agn, iwmc3200wifi, libertas, mwl8k, rt2x00, wl1251, wl12xx. The drivers have been compile-tested only. Signed-off-by: NBruno Randolf <br1@einfach.org> Signed-off-by: NBrian Prodoehl <bprodoehl@gmail.com> Acked-by: NLuciano Coelho <coelho@ti.com> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
- 14 12月, 2010 1 次提交
-
-
由 Johannes Berg 提交于
Allow userspace to specify that a given key is default only for unicast and/or multicast transmissions. Only WEP keys are for both, WPA/RSN keys set here are GTKs for multicast only. For more future flexibility, allow to specify all combiations. Wireless extensions can only set both so use nl80211; WEP keys (connect keys) must be set as default for both (but 802.1X WEP is still possible). Signed-off-by: NJohannes Berg <johannes.berg@intel.com> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
- 07 12月, 2010 1 次提交
-
-
由 Johannes Berg 提交于
Instead of tying mesh activity to interface up, add join and leave commands for mesh. Since we must be backward compatible, let cfg80211 handle joining a mesh if a mesh ID was pre-configured when the device goes up. Note that this therefore must modify mac80211 as well since mac80211 needs to lose the logic to start the mesh on interface up. We now allow querying mesh parameters before the mesh is connected, which simply returns defaults. Setting them (internally renamed to "update") is only allowed while connected. Specify them with the new mesh join command instead where needed. In mac80211, beaconing must now also follow the mesh enabled/not enabled state, which is done by testing the mesh ID. Signed-off-by: NJavier Cardona <javier@cozybit.com> Signed-off-by: NJohannes Berg <johannes.berg@intel.com> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
- 25 11月, 2010 1 次提交
-
-
由 Joe Perches 提交于
No change in output for pr_<level> prefixes. netdev_<level> output is different, arguably improved. Signed-off-by: NJoe Perches <joe@perches.com> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
- 07 10月, 2010 1 次提交
-
-
由 Johannes Berg 提交于
This adds API to allow adding per-station GTKs, updates mac80211 to support it, and also allows drivers to remove a key from hwaccel again when this may be necessary due to multiple GTKs. Signed-off-by: NJohannes Berg <johannes.berg@intel.com> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
- 17 9月, 2010 1 次提交
-
-
由 Johannes Berg 提交于
This adds P2P-STA and P2P-GO as device types so we can distinguish between those and normal STA or AP (respectively) type interfaces. Signed-off-by: NJohannes Berg <johannes.berg@intel.com> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
- 28 8月, 2010 1 次提交
-
-
由 Johannes Berg 提交于
cfg80211 currently rejects all cipher suites it doesn't know about for key length checking purposes. This can lead to inconsistencies when a driver advertises an algorithm that cfg80211 doesn't know about. Remove this rejection so drivers can specify any algorithm they like. Signed-off-by: NJohannes Berg <johannes.berg@intel.com> Signed-off-by: NJuuso Oikarinen <juuso.oikarinen@nokia.com> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
- 25 8月, 2010 2 次提交
-
-
由 Johannes Berg 提交于
Allow userspace to register for more than just action frames by giving the frame subtype, and make it possible to use this in various modes as well. With some tweaks and some added functionality this will, in the future, also be usable in AP mode and be able to replace the cooked monitor interface currently used in that case. Signed-off-by: NJohannes Berg <johannes.berg@intel.com> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Johannes Berg 提交于
This function analyses only its single, value-passed argument, and has no side effects. Thus it can be const, which makes mac80211 smaller, for example: text data bss dec hex filename 362518 16720 884 380122 5ccda mac80211.ko (before) 362358 16720 884 379962 5cc3a mac80211.ko (after) a 160 byte saving in text size, and an optimisation because the function won't be called as often. Signed-off-by: NJohannes Berg <johannes.berg@intel.com> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
- 16 6月, 2010 1 次提交
-
-
由 Jiri Pirko 提交于
Register net_bridge_port pointer as rx_handler data pointer. As br_port is removed from struct net_device, another netdev priv_flag is added to indicate the device serves as a bridge port. Also rcuized pointers are now correctly dereferenced in br_fdb.c and in netfilter parts. Signed-off-by: NJiri Pirko <jpirko@redhat.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
- 01 4月, 2010 1 次提交
-
-
由 Zhu Yi 提交于
Mac80211 drivers can now pass paged SKBs to mac80211 via ieee80211_rx{_irqsafe}. The implementation currently use skb_linearize() in a few places i.e. management frame handling, software decryption, defragmentation and A-MSDU process. We will optimize them one by one later. Signed-off-by: NZhu Yi <yi.zhu@intel.com> Cc: Kalle Valo <kalle.valo@iki.fi> Cc: Johannes Berg <johannes@sipsolutions.net> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
- 30 3月, 2010 1 次提交
-
-
由 Tejun Heo 提交于
include cleanup: Update gfp.h and slab.h includes to prepare for breaking implicit slab.h inclusion from percpu.h percpu.h is included by sched.h and module.h and thus ends up being included when building most .c files. percpu.h includes slab.h which in turn includes gfp.h making everything defined by the two files universally available and complicating inclusion dependencies. percpu.h -> slab.h dependency is about to be removed. Prepare for this change by updating users of gfp and slab facilities include those headers directly instead of assuming availability. As this conversion needs to touch large number of source files, the following script is used as the basis of conversion. http://userweb.kernel.org/~tj/misc/slabh-sweep.py The script does the followings. * Scan files for gfp and slab usages and update includes such that only the necessary includes are there. ie. if only gfp is used, gfp.h, if slab is used, slab.h. * When the script inserts a new include, it looks at the include blocks and try to put the new include such that its order conforms to its surrounding. It's put in the include block which contains core kernel includes, in the same order that the rest are ordered - alphabetical, Christmas tree, rev-Xmas-tree or at the end if there doesn't seem to be any matching order. * If the script can't find a place to put a new include (mostly because the file doesn't have fitting include block), it prints out an error message indicating which .h file needs to be added to the file. The conversion was done in the following steps. 1. The initial automatic conversion of all .c files updated slightly over 4000 files, deleting around 700 includes and adding ~480 gfp.h and ~3000 slab.h inclusions. The script emitted errors for ~400 files. 2. Each error was manually checked. Some didn't need the inclusion, some needed manual addition while adding it to implementation .h or embedding .c file was more appropriate for others. This step added inclusions to around 150 files. 3. The script was run again and the output was compared to the edits from #2 to make sure no file was left behind. 4. Several build tests were done and a couple of problems were fixed. e.g. lib/decompress_*.c used malloc/free() wrappers around slab APIs requiring slab.h to be added manually. 5. The script was run on all .h files but without automatically editing them as sprinkling gfp.h and slab.h inclusions around .h files could easily lead to inclusion dependency hell. Most gfp.h inclusion directives were ignored as stuff from gfp.h was usually wildly available and often used in preprocessor macros. Each slab.h inclusion directive was examined and added manually as necessary. 6. percpu.h was updated not to include slab.h. 7. Build test were done on the following configurations and failures were fixed. CONFIG_GCOV_KERNEL was turned off for all tests (as my distributed build env didn't work with gcov compiles) and a few more options had to be turned off depending on archs to make things build (like ipr on powerpc/64 which failed due to missing writeq). * x86 and x86_64 UP and SMP allmodconfig and a custom test config. * powerpc and powerpc64 SMP allmodconfig * sparc and sparc64 SMP allmodconfig * ia64 SMP allmodconfig * s390 SMP allmodconfig * alpha SMP allmodconfig * um on x86_64 SMP allmodconfig 8. percpu.h modifications were reverted so that it could be applied as a separate patch and serve as bisection point. Given the fact that I had only a couple of failures from tests on step 6, I'm fairly confident about the coverage of this conversion patch. If there is a breakage, it's likely to be something in one of the arch headers which should be easily discoverable easily on most builds of the specific arch. Signed-off-by: NTejun Heo <tj@kernel.org> Guess-its-ok-by: NChristoph Lameter <cl@linux-foundation.org> Cc: Ingo Molnar <mingo@redhat.com> Cc: Lee Schermerhorn <Lee.Schermerhorn@hp.com>
-
- 23 1月, 2010 1 次提交
-
-
由 Andriy Tkachuk 提交于
ieee80211_hdrlen() should account account new HT Control field in 802.11 data frame header introduced by IEEE 802.11n standard. According to 802.11n-2009 HT Control field is present in data frames when both of following are met: 1. It is QoS data frame. 2. Order bit is set in Frame Control field. The change might be totally compatible with legacy non-11n aware frames, because 802.11-2007 standard states that "all QoS STAs set this subfield to 0". Signed-off-by: NAndriy V. Tkachuk <andrit@ukr.net> Acked-by : Benoit Papillault <benoit.papillault@free.fr> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
- 23 12月, 2009 1 次提交
-
-
由 Zhu Yi 提交于
Move the A-MSDU handling code from mac80211 to cfg80211 so that more drivers can use it. The new created function ieee80211_amsdu_to_8023s converts an A-MSDU frame to a list of 802.3 frames. Cc: Johannes Berg <johannes@sipsolutions.net> Signed-off-by: NZhu Yi <yi.zhu@intel.com> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
- 22 12月, 2009 1 次提交
-
-
由 John W. Linville 提交于
Previously, cfg80211 had reported "0" for MCS (i.e. 802.11n) bitrates through the wireless extensions interface. However, nl80211 was converting MCS rates into a reasonable bitrate number. This patch moves the nl80211 code to cfg80211 where it is now shared between both the nl80211 interface and the wireless extensions interface. Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
- 20 11月, 2009 2 次提交
-
-
由 Johannes Berg 提交于
A number of people have tried to add a wireless interface (in managed mode) to a bridge and then complained that it doesn't work. It cannot work, however, because in 802.11 networks all packets need to be acknowledged and as such need to be sent to the right address. Promiscuous doesn't help here. The wireless address format used for these links has only space for three addresses, the * transmitter, which must be equal to the sender (origin) * receiver (on the wireless medium), which is the AP in the case of managed mode * the recipient (destination), which is on the APs local network segment In an IBSS, it is similar, but the receiver and recipient must match and the third address is used as the BSSID. To avoid such mistakes in the future, disallow adding a wireless interface to a bridge. Felix has recently added a four-address mode to the AP and client side that can be used (after negotiating that it is possible, which must happen out-of-band by setting up both sides) for bridging, so allow that case. Signed-off-by: NJohannes Berg <johannes@sipsolutions.net> Acked-by: NStephen Hemminger <shemminger@vyatta.com> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Johannes Berg 提交于
It's very likely that not many devices will support four-address mode in station or AP mode so introduce capability bits for both modes, set them in mac80211 and check them when userspace tries to use the mode. Also, keep track of 4addr in cfg80211 (wireless_dev) and not in mac80211 any more. mac80211 can also be improved for the VLAN case by not looking at the 4addr flag but maintaining the station pointer for it correctly. However, keep track of use_4addr for station mode in mac80211 to avoid all the derefs. Signed-off-by: NJohannes Berg <johannes@sipsolutions.net> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
- 12 11月, 2009 1 次提交
-
-
由 Felix Fietkau 提交于
In some situations it might be useful to run a network with an Access Point and multiple clients, but with each client bridged to a network behind it. For this to work, both the client and the AP need to transmit 4-address frames, containing both source and destination MAC addresses. With this patch, you can configure a client to communicate using only 4-address frames for data traffic. On the AP side you can enable 4-address frames for individual clients by isolating them in separate AP VLANs which are configured in 4-address mode. Such an AP VLAN will be limited to one client only, and this client will be used as the destination for all traffic on its interface, regardless of the destination MAC address in the packet headers. The advantage of this mode compared to regular WDS mode is that it's easier to configure and does not require a static list of peer MAC addresses on any side. Signed-off-by: NFelix Fietkau <nbd@openwrt.org> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
- 29 8月, 2009 1 次提交
-
-
由 Johannes Berg 提交于
When the interface type changes while connected, and the driver does not require the interface to be down for a type change, it is currently possible to get very strange results unless the driver takes special care, which it shouldn't have to. To fix this, take care to disconnect/leave IBSS when changing the interface type -- even if the driver may fail the call. Also process all events that may be pending to avoid running into a situation where an event is reported but only processed after the type has already changed, which would lead to missing events and warnings. A side effect of this is that you will have disconnected or left the IBSS even if the mode change ultimately fails, but since the intention was to change it and thus leave or disconnect, this is not a problem. Signed-off-by: NJohannes Berg <johannes@sipsolutions.net> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
- 14 8月, 2009 1 次提交
-
-
由 Javier Cardona 提交于
The 11s task group recently changed the frame mesh multicast/broadcast frame format to use 3-address. This was done to avoid interactions with widely deployed lazy-WDS access points. This patch changes the format of group addressed frames, both mesh-originated and proxied, to use the data format defined in draft D2.08 and forward. The address fields used for group addressed frames is: In 802.11 header ToDS:0 FromDS:1 addr1: DA (broadcast/multicast address) addr2: TA addr3: Mesh SA In address extension header: addr4: SA (only present if frame was proxied) Note that this change breaks backward compatibility with earlier mesh stack versions. Signed-off-by: NAndrey Yurovsky <andrey@cozybit.com> Signed-off-by: NJavier Cardona <javier@cozybit.com> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
- 25 7月, 2009 2 次提交
-
-
由 Zhu Yi 提交于
In cfg80211_upload_connect_keys(), we call add_key, set_default_key and set_default_mgmt_key (if applicable) one by one. If one of these operations fails, we should stop calling the following functions. Because if the key is not added successfully, we should not set it as default key anyway. Signed-off-by: NZhu Yi <yi.zhu@intel.com> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Johannes Berg 提交于
This reworks the key operation in cfg80211, and now only allows, from userspace, configuring keys (via nl80211) after the connection has been established (in managed mode), the IBSS been joined (in IBSS mode), at any time (in AP[_VLAN] modes) or never for all the other modes. In order to do shared key authentication correctly, it is now possible to give a WEP key to the AUTH command. To configure static WEP keys, these are given to the CONNECT or IBSS_JOIN command directly, for a userspace SME it is assumed it will configure it properly after the connection has been established. Since mac80211 used to check the default key in IBSS mode to see whether or not the network is protected, it needs an update in that area, as well as an update to make use of the WEP key passed to auth() for shared key authentication. Signed-off-by: NJohannes Berg <johannes@sipsolutions.net> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
- 11 7月, 2009 1 次提交
-
-
由 Johannes Berg 提交于
This function from mac80211 seems generally useful, and I will need it in cfg80211 soon. Signed-off-by: NJohannes Berg <johannes@sipsolutions.net> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
- 04 6月, 2009 2 次提交
-
-
由 Luis R. Rodriguez 提交于
Fixes spares warning: net/wireless/util.c:261:5: warning: symbol 'ieee80211_get_mesh_hdrlen' was not declared. Should it be static? Signed-off-by: NLuis R. Rodriguez <lrodriguez@atheros.com> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Johannes Berg 提交于
Instead of hardcoding the key length for validation, use the constants Zhu Yi recently added and add one for AES_CMAC too. Signed-off-by: NJohannes Berg <johannes@sipsolutions.net> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
- 23 5月, 2009 1 次提交
-
-
由 Zhu Yi 提交于
The patch moves some utility functions from mac80211 to cfg80211. Because these functions are doing generic 802.11 operations so they are not mac80211 specific. The moving allows some fullmac drivers to be also benefit from these utility functions. Signed-off-by: NZhu Yi <yi.zhu@intel.com> Signed-off-by: NSamuel Ortiz <samuel.ortiz@intel.com> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
- 21 5月, 2009 1 次提交
-
-
由 Jouni Malinen 提交于
Validate RSC (NL80211_ATTR_KEY_SEQ) length in nl80211/cfg80211 instead of having to do this in all the drivers. Signed-off-by: NJouni Malinen <jouni.malinen@atheros.com> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
- 14 5月, 2009 1 次提交
-
-
由 Johannes Berg 提交于
Move key handling wireless extension ioctls from mac80211 to cfg80211 so that all drivers that implement the cfg80211 operations get wext compatibility. Note that this drops the SIOCGIWENCODE ioctl support for getting IW_ENCODE_RESTRICTED/IW_ENCODE_OPEN. This means that iwconfig will no longer report "Security mode:open" or "Security mode:restricted" for mac80211. However, what we displayed there (the authentication algo used) was actually wrong -- linux/wireless.h states that this setting is meant to differentiate between "Refuse non-encoded packets" and "Accept non-encoded packets". (Combined with "cfg80211: fix a couple of bugs with key ioctls". -- JWL) Signed-off-by: NJohannes Berg <johannes@sipsolutions.net> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
- 23 4月, 2009 1 次提交
-
-
由 Johannes Berg 提交于
Trying to separate header files into net/wireless.h and net/cfg80211.h has been a source of confusion. Remove net/wireless.h (because there also is the linux/wireless.h) and subsume everything into net/cfg80211.h -- except the definitions for regulatory structures which get moved to a new header net/regulatory.h. The "new" net/cfg80211.h is now divided into sections. There are no real changes in this patch but code shuffling and some very minor documentation fixes. I have also, to make things reflect reality, put in a copyright line for Luis to net/regulatory.h since that is probably exclusively written by him but was formerly in a file that only had my copyright line. Signed-off-by: NJohannes Berg <johannes@sipsolutions.net> Cc: Luis R. Rodriguez <lrodriguez@atheros.com> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
- 30 1月, 2009 1 次提交
-
-
由 Johannes Berg 提交于
Since the standards only define 12 legacy rates, 32 is certainly a sane upper limit and we don't need to use u64 everywhere. Add sanity checking that no more than 32 rates are registered and change the variables to u32 throughout. Signed-off-by: NJohannes Berg <johannes@sipsolutions.net> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
- 11 11月, 2008 1 次提交
-
-
由 Johannes Berg 提交于
This adds a helper function that, given a bitmap of basic rates and a bitrate returns the response rate for this rate. Signed-off-by: NJohannes Berg <johannes@sipsolutions.net> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
- 28 3月, 2008 1 次提交
-
-
由 Johannes Berg 提交于
This patch makes ieee80211_get_channel a static inline defined in cfg80211's header file which simply calls __ieee80211_get_channel to avoid symbol clashes with the ieee80211 code. The problem was pointed out by David Miller, thanks! Signed-off-by: NJohannes Berg <johannes@sipsolutions.net> Cc: David Miller <davem@davemloft.net> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
- 26 3月, 2008 1 次提交
-
-
由 Johannes Berg 提交于
Add ieee80211_get_channel() which gets you a channel struct for a specific wiphy if that channel is present in that wiphy. Signed-off-by: NJohannes Berg <johannes@sipsolutions.net> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
- 01 3月, 2008 3 次提交
-
-
由 Ivo van Doorn 提交于
When the driver registers a IEEE80211_BAND_2GHZ band, it can either be 802.11b or 802.11g. But when 802.11b rates are registered "want" will be 3 (since 4 rates are being registered, and each of those 4 rates will decrease "want"). Since this is a correct situation, there is no need to trigger a WARN_ON() for this. Signed-off-by: NIvo van Doorn <IvDoorn@gmail.com> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Johannes Berg 提交于
In the rate API patch I accidentally reverted the test for ERP rates, this fixes it. All rates except 1, 2, 5.5 and 11 MBit are ERP rates, not those. Signed-off-by: NJohannes Berg <johannes@sipsolutions.net> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Johannes Berg 提交于
This patch creates new cfg80211 wiphy API for channel and bitrate registration and converts mac80211 and drivers to the new API. The old mac80211 API is completely ripped out. All drivers (except ath5k) are updated to the new API, in many cases I expect that optimisations can be done. Along with the regulatory code I've also ripped out the IEEE80211_HW_DEFAULT_REG_DOMAIN_CONFIGURED flag, I believe it to be unnecessary if the hardware simply gives us whatever channels it wants to support and we then enable/disable them as required, which is pretty much required for travelling. Additionally, the patch adds proper "basic" rate handling for STA mode interface, AP mode interface will have to have new API added to allow userspace to set the basic rate set, currently it'll be empty... However, the basic rate handling will need to be moved to the BSS conf stuff. I do expect there to be bugs in this, especially wrt. transmit power handling where I'm basically clueless about how it should work. Signed-off-by: NJohannes Berg <johannes@sipsolutions.net> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-