Signed-off-by: NFelix Fietkau <nbd@openwrt.org>
Tested-by: NBen Greear <greearb@candelatech.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Embedded boards do not have compressed EEPROM data, they use the
struct ar9003_eeprom layout, with little endian fields, so copying
the raw data to the eeprom buffer is enough.
Signed-off-by: NFelix Fietkau <nbd@openwrt.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Some embedded boards store platform data for connected PCIe AR92xx
chips in the system flash instead of a separate EEPROM chip.
Signed-off-by: NGabor Juhos <juhosg@openwrt.org>
Signed-off-by: NFelix Fietkau <nbd@openwrt.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Some of the new AR9003 cards do not come with an external EEPROM chip
anymore. Calibration data on these cards is stored in the OTP ROM on
the chip.
This patch adds support for reading this data, and also adds support
for different EEPROM chip sizes (512 bytes instead of 1K).
Signed-off-by: NFelix Fietkau <nbd@openwrt.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Since the pointers after the rates in the tx info cannot be used anymore
after frames have been queued, this area can be used to store information
that was previously stored in the ath_buf. With these changes, we can delay
the ath_buf assignment in the aggregation code until aggregates are formed.

That will not only make it possible to simplify DMA descriptor setup to
do less rewriting of uncached memory, but will also make it easier to
move aggregation out of the core of the ath9k tx path.
Signed-off-by: NFelix Fietkau <nbd@openwrt.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

- remove the BUF_HT flag, and instead check for IEEE80211_TX_CTL_AMPDU
  before calling ath_tx_send_ampdu.
- remove a few unused variables
- calculate frame length before adding the frame padding
- merge the misnamed ath_tx_start_dma function into ath_tx_start
- remove an unused argument for assign_aggr_tid_seqno
Signed-off-by: NFelix Fietkau <nbd@openwrt.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This makes further tx path cleanups easier
Signed-off-by: NFelix Fietkau <nbd@openwrt.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Merge initial processing for the CAB queue and regular tx.
Also move ath_tx_cabq() to beacon.c and make it static.
Signed-off-by: NFelix Fietkau <nbd@openwrt.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: NFelix Fietkau <nbd@openwrt.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: NFelix Fietkau <nbd@openwrt.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: NFelix Fietkau <nbd@openwrt.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: NFelix Fietkau <nbd@openwrt.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: NFelix Fietkau <nbd@openwrt.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: NFelix Fietkau <nbd@openwrt.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: NFelix Fietkau <nbd@openwrt.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: NFelix Fietkau <nbd@openwrt.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: NFelix Fietkau <nbd@openwrt.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: NFelix Fietkau <nbd@openwrt.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: NFelix Fietkau <nbd@openwrt.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The calibration data variable size is based on the number of
channels available in the ath9k driver.
Signed-off-by: NMohammed Shafi Shajakhan <mshajakhan@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: NFelix Fietkau <nbd@openwrt.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Merge ath_tx_send_normal and ath_tx_send_ht_normal.
Move the paprd state initialization and sequence number assignment
to reduce the number of redundant checks.

This not only simplifies buffer allocation error handling, but also
removes a small inconsistency in the buffer HT flag.
This flag should only be set if the frame is also a QoS data frame.
Signed-off-by: NFelix Fietkau <nbd@openwrt.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: NFelix Fietkau <nbd@openwrt.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: NFelix Fietkau <nbd@openwrt.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: NFelix Fietkau <nbd@openwrt.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

TX underruns were noticed when RTS/CTS preceded aggregates.
This issue was noticed in ar93xx family of chipsets only.
The workaround involves padding the RTS or CTS length up
to the min packet length of 256 bytes required by the
hardware by adding delimiters to the fist descriptor of
the aggregate.
Signed-off-by: NSenthil Balasubramanian <senthilkumar@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

There is a roundng error in delimiter padding computation
which causes severe throughput drop with some of AR9003.
signed-off-by: NFelix Fietkau <nbd@openwrt.org>
Signed-off-by: NVasanthakumar Thiagarajan <vasanth@atheros.com>
Cc:stable@kernel.org
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Also round off interpolated values this would improve power
accuracy by 0.5dB in some cases.
Signed-off-by: NVasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

It is done for 5Ghz by adding three temperature slopes.
Signed-off-by: NVasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Attenuation from eeprom is configured into attenuator control
register.
Signed-off-by: NVasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Improper configuration of 0x16288 and 0x16290 would affect transmission.

Cc:stable@kernel.org
Signed-off-by: NVasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

We are currently using the default eeprom default and it doesn't
work properly for all ar9003 family chipsets. So add eeprom
templates for different versisons and select the eeprom table
based on the template version programmed in the eeprom.
Signed-off-by: NSenthil Balasubramanian <senthilkumar@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

paprd training frame fails in some rates. Fix the rate mask.
Signed-off-by: NSenthil Balasubramanian <senthilkumar@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The last 2GHz CTL was not being initialized, so power was being
set to 0 instead of 30dbm. Initialize to 30 like other CTLs.
Signed-off-by: NSenthil Balasubramanian <senthilkumar@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Add eeprom base extension structures which are needed for
AR938x caliberation changes and gain calculation.
Signed-off-by: NSenthil Balasubramanian <senthilkumar@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

AR9382 needs to be configured for the correct chain mask before
running AGC/TxIQ caliberation. Otherwise reset would fail.
Signed-off-by: NSenthil Balasubramanian <senthilkumar@atheros.com>
Signed-off-by: NVasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This patch moves code out from wireless drivers where two different
functions are defined in three code locations for the same purpose and
provides a common function to sign extend a 32-bit value.
Signed-off-by: NAndreas Herrmann <andreas.herrmann3@amd.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The current ath9k tx queue handling code showed a few issues that could
lead to locking issues, tx stalls due to stopped queues, and maybe even
DMA issues.

The main source of these issues is that in some places the queue is
selected via skb queue mapping in places where this mapping may no
longer be valid. One such place is when data frames are transmitted via
the CAB queue (for powersave buffered frames). This is made even worse
by a lookup WMM AC values from the assigned tx queue (which is
undefined for the CAB queue).

This messed up the pending frame counting, which in turn caused issues
with queues getting stopped, but not woken again.

To fix these issues, this patch removes an unnecessary abstraction
separating a driver internal queue number from the skb queue number
(not to be confused with the hardware queue number).

It seems that this abstraction may have been necessary because of tx
queue preinitialization from the initvals. This patch avoids breakage
here by pushing the software <-> hardware queue mapping to the function
that assigns the tx queues and redefining the WMM AC definitions to
match the numbers used by mac80211 (also affects ath9k_htc).

To ensure consistency wrt. pending frame count tracking, these counters
are moved to the ath_txq struct, updated with the txq lock held, but
only where the tx queue selected by the skb queue map actually matches
the tx queue used by the driver for the frame.
Signed-off-by: NFelix Fietkau <nbd@openwrt.org>
Reported-by: NBjörn Smedman <bjorn.smedman@venatech.se>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This helps align resets / RX enable & disable / TX stop / start.
Locking around the PCU is important to ensure the hardware doesn't
get stale data when working with DMA'able data.

This is part of a series of patches which fix stopping
TX DMA completley when requested on the driver.
For more details about this issue refer to this thread:

http://marc.info/?l=linux-wireless&m=128629803703756&w=2Tested-by: NBen Greear <greearb@candelatech.com>
Cc: Kyungwan Nam <kyungwan.nam@atheros.com>
Cc: stable@kernel.org
Signed-off-by: NLuis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The PCU lock should be used to contend TX DMA as well,
this will be done next.

This is part of a series of patches which fix stopping
TX DMA completley when requested on the driver.
For more details about this issue refer to this thread:

http://marc.info/?l=linux-wireless&m=128629803703756&w=2Tested-by: NBen Greear <greearb@candelatech.com>
Cc: Kyungwan Nam <kyungwan.nam@atheros.com>
Cc: stable@kernel.org
Signed-off-by: NLuis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>