It will be used in arch/powerpc/kvm/book3s_hv.c KVM module.
Signed-off-by: NMahesh Salgaonkar <mahesh@linux.vnet.ibm.com>
Acked-by: NMichael Ellerman <mpe@ellerman.id.au>
Signed-off-by: NPaul Mackerras <paulus@ozlabs.org>

This introduces a new KVM capability to control how KVM behaves
on machine check exception (MCE) in HV KVM guests.

If this capability has not been enabled, KVM redirects machine check
exceptions to guest's 0x200 vector, if the address in error belongs to
the guest. With this capability enabled, KVM will cause a guest exit
with the exit reason indicating an NMI.

The new capability is required to avoid problems if a new kernel/KVM
is used with an old QEMU, running a guest that doesn't issue
"ibm,nmi-register".  As old QEMU does not understand the NMI exit
type, it treats it as a fatal error.  However, the guest could have
handled the machine check error if the exception was delivered to
guest's 0x200 interrupt vector instead of NMI exit in case of old
QEMU.

[paulus@ozlabs.org - Reworded the commit message to be clearer,
 enable only on HV KVM.]
Signed-off-by: NAravinda Prasad <aravinda@linux.vnet.ibm.com>
Reviewed-by: NDavid Gibson <david@gibson.dropbear.id.au>
Signed-off-by: NMahesh Salgaonkar <mahesh@linux.vnet.ibm.com>
Signed-off-by: NPaul Mackerras <paulus@ozlabs.org>

On a POWER9 system, it is possible for an interrupt to become pending
for a VCPU when that VCPU is about to cede (execute a H_CEDE hypercall)
and has already disabled interrupts, or in the H_CEDE processing up
to the point where the XIVE context is pulled from the hardware.  In
such a case, the H_CEDE should not sleep, but should return immediately
to the guest.  However, the conditions tested in kvmppc_vcpu_woken()
don't include the condition that a XIVE interrupt is pending, so the
VCPU could sleep until the next decrementer interrupt.

To fix this, we add a new xive_interrupt_pending() helper which looks
in the XIVE context that was pulled from the hardware to see if the
priority of any pending interrupt is higher (numerically lower than)
the CPU priority.  If so then kvmppc_vcpu_woken() will return true.
If the XIVE context has never been used, then both the pipr and the
cppr fields will be zero and the test will indicate that no interrupt
is pending.
Signed-off-by: NPaul Mackerras <paulus@ozlabs.org>

On POWER9, we no longer have the restriction that we had on POWER8
where all threads in a core have to be in the same partition, so
the CPU threads are now independent.  However, we still want to be
able to run guests with a virtual SMT topology, if only to allow
migration of guests from POWER8 systems to POWER9.

A guest that has a virtual SMT mode greater than 1 will expect to
be able to use the doorbell facility; it will expect the msgsndp
and msgclrp instructions to work appropriately and to be able to read
sensible values from the TIR (thread identification register) and
DPDES (directed privileged doorbell exception status) special-purpose
registers.  However, since each CPU thread is a separate sub-processor
in POWER9, these instructions and registers can only be used within
a single CPU thread.

In order for these instructions to appear to act correctly according
to the guest's virtual SMT mode, we have to trap and emulate them.
We cause them to trap by clearing the HFSCR_MSGP bit in the HFSCR
register.  The emulation is triggered by the hypervisor facility
unavailable interrupt that occurs when the guest uses them.

To cause a doorbell interrupt to occur within the guest, we set the
DPDES register to 1.  If the guest has interrupts enabled, the CPU
will generate a doorbell interrupt and clear the DPDES register in
hardware.  The DPDES hardware register for the guest is saved in the
vcpu->arch.vcore->dpdes field.  Since this gets written by the guest
exit code, other VCPUs wishing to cause a doorbell interrupt don't
write that field directly, but instead set a vcpu->arch.doorbell_request
flag.  This is consumed and set to 0 by the guest entry code, which
then sets DPDES to 1.

Emulating reads of the DPDES register is somewhat involved, because
it requires reading the doorbell pending interrupt status of all of the
VCPU threads in the virtual core, and if any of those VCPUs are
running, their doorbell status is only up-to-date in the hardware
DPDES registers of the CPUs where they are running.  In order to get
a reasonable approximation of the current doorbell status, we send
those CPUs an IPI, causing an exit from the guest which will update
the vcpu->arch.vcore->dpdes field.  We then use that value in
constructing the emulated DPDES register value.
Signed-off-by: NPaul Mackerras <paulus@ozlabs.org>

This allows userspace to set the desired virtual SMT (simultaneous
multithreading) mode for a VM, that is, the number of VCPUs that
get assigned to each virtual core.  Previously, the virtual SMT mode
was fixed to the number of threads per subcore, and if userspace
wanted to have fewer vcpus per vcore, then it would achieve that by
using a sparse CPU numbering.  This had the disadvantage that the
vcpu numbers can get quite large, particularly for SMT1 guests on
a POWER8 with 8 threads per core.  With this patch, userspace can
set its desired virtual SMT mode and then use contiguous vcpu
numbering.

On POWER8, where the threading mode is "strict", the virtual SMT mode
must be less than or equal to the number of threads per subcore.  On
POWER9, which implements a "loose" threading mode, the virtual SMT
mode can be any power of 2 between 1 and 8, even though there is
effectively one thread per subcore, since the threads are independent
and can all be in different partitions.
Signed-off-by: NPaul Mackerras <paulus@ozlabs.org>

This adds code to allow us to use a different value for the HFSCR
(Hypervisor Facilities Status and Control Register) when running the
guest from that which applies in the host.  The reason for doing this
is to allow us to trap the msgsndp instruction and related operations
in future so that they can be virtualized.  We also save the value of
HFSCR when a hypervisor facility unavailable interrupt occurs, because
the high byte of HFSCR indicates which facility the guest attempted to
access.

We save and restore the host value on guest entry/exit because some
bits of it affect host userspace execution.

We only do all this on POWER9, not on POWER8, because we are not
intending to virtualize any of the facilities controlled by HFSCR on
POWER8.  In particular, the HFSCR bit that controls execution of
msgsndp and related operations does not exist on POWER8.  The HFSCR
doesn't exist at all on POWER7.
Signed-off-by: NPaul Mackerras <paulus@ozlabs.org>

It is possible, through a narrow race condition, for a VCPU to exit
the guest with a H_CEDE hypercall while it has a doorbell interrupt
pending.  In this case, the H_CEDE should return immediately, but in
fact it puts the VCPU to sleep until some other interrupt becomes
pending or a prod is received (via another VCPU doing H_PROD).

This fixes it by checking the DPDES (Directed Privileged Doorbell
Exception Status) bit for the thread along with the other interrupt
pending bits.
Signed-off-by: NPaul Mackerras <paulus@ozlabs.org>

This allows userspace (e.g. QEMU) to enable large decrementer mode for
the guest when running on a POWER9 host, by setting the LPCR_LD bit in
the guest LPCR value.  With this, the guest exit code saves 64 bits of
the guest DEC value on exit.  Other places that use the guest DEC
value check the LPCR_LD bit in the guest LPCR value, and if it is set,
omit the 32-bit sign extension that would otherwise be done.

This doesn't change the DEC emulation used by PR KVM because PR KVM
is not supported on POWER9 yet.

This is partly based on an earlier patch by Oliver O'Halloran.
Signed-off-by: NPaul Mackerras <paulus@ozlabs.org>

POWER9 DD1 has an erratum where writing to the TBU40 register, which
is used to apply an offset to the timebase, can cause the timebase to
lose counts.  This results in the timebase on some CPUs getting out of
sync with other CPUs, which then results in misbehaviour of the
timekeeping code.

To work around the problem, we make KVM ignore the timebase offset for
all guests on POWER9 DD1 machines.  This means that live migration
cannot be supported on POWER9 DD1 machines.

Cc: stable@vger.kernel.org # v4.10+
Signed-off-by: NPaul Mackerras <paulus@ozlabs.org>

At present, HV KVM on POWER8 and POWER9 machines loses any instruction
or data breakpoint set in the host whenever a guest is run.
Instruction breakpoints are currently only used by xmon, but ptrace
and the perf_event subsystem can set data breakpoints as well as xmon.

To fix this, we save the host values of the debug registers (CIABR,
DAWR and DAWRX) before entering the guest and restore them on exit.
To provide space to save them in the stack frame, we expand the stack
frame allocated by kvmppc_hv_entry() from 112 to 144 bytes.

Fixes: b005255e ("KVM: PPC: Book3S HV: Context-switch new POWER8 SPRs", 2014-01-08)
Cc: stable@vger.kernel.org # v3.14+
Signed-off-by: NPaul Mackerras <paulus@ozlabs.org>

If userspace attempts to call the KVM_RUN ioctl when it has hardware
transactional memory (HTM) enabled, the values that it has put in the
HTM-related SPRs TFHAR, TFIAR and TEXASR will get overwritten by
guest values.  To fix this, we detect this condition and save those
SPR values in the thread struct, and disable HTM for the task.  If
userspace goes to access those SPRs or the HTM facility in future,
a TM-unavailable interrupt will occur and the handler will reload
those SPRs and re-enable HTM.

If userspace has started a transaction and suspended it, we would
currently lose the transactional state in the guest entry path and
would almost certainly get a "TM Bad Thing" interrupt, which would
cause the host to crash.  To avoid this, we detect this case and
return from the KVM_RUN ioctl with an EINVAL error, with the KVM
exit reason set to KVM_EXIT_FAIL_ENTRY.

Fixes: b005255e ("KVM: PPC: Book3S HV: Context-switch new POWER8 SPRs", 2014-01-08)
Cc: stable@vger.kernel.org # v3.14+
Signed-off-by: NPaul Mackerras <paulus@ozlabs.org>

This restores several special-purpose registers (SPRs) to sane values
on guest exit that were missed before.

TAR and VRSAVE are readable and writable by userspace, and we need to
save and restore them to prevent the guest from potentially affecting
userspace execution (not that TAR or VRSAVE are used by any known
program that run uses the KVM_RUN ioctl).  We save/restore these
in kvmppc_vcpu_run_hv() rather than on every guest entry/exit.

FSCR affects userspace execution in that it can prohibit access to
certain facilities by userspace.  We restore it to the normal value
for the task on exit from the KVM_RUN ioctl.

IAMR is normally 0, and is restored to 0 on guest exit.  However,
with a radix host on POWER9, it is set to a value that prevents the
kernel from executing user-accessible memory.  On POWER9, we save
IAMR on guest entry and restore it on guest exit to the saved value
rather than 0.  On POWER8 we continue to set it to 0 on guest exit.

PSPB is normally 0.  We restore it to 0 on guest exit to prevent
userspace taking advantage of the guest having set it non-zero
(which would allow userspace to set its SMT priority to high).

UAMOR is normally 0.  We restore it to 0 on guest exit to prevent
the AMR from being used as a covert channel between userspace
processes, since the AMR is not context-switched at present.

Fixes: b005255e ("KVM: PPC: Book3S HV: Context-switch new POWER8 SPRs", 2014-01-08)
Cc: stable@vger.kernel.org # v3.14+
Signed-off-by: NPaul Mackerras <paulus@ozlabs.org>

This adds code to save the values of three SPRs (special-purpose
registers) used by userspace to control event-based branches (EBBs),
which are essentially interrupts that get delivered directly to
userspace.  These registers are loaded up with guest values when
entering the guest, and their values are saved when exiting the
guest, but we were not saving the host values and restoring them
before going back to userspace.

On POWER8 this would only affect userspace programs which explicitly
request the use of EBBs and also use the KVM_RUN ioctl, since the
only source of EBBs on POWER8 is the PMU, and there is an explicit
enable bit in the PMU registers (and those PMU registers do get
properly context-switched between host and guest).  On POWER9 there
is provision for externally-generated EBBs, and these are not subject
to the control in the PMU registers.

Since these registers only affect userspace, we can save them when
we first come in from userspace and restore them before returning to
userspace, rather than saving/restoring the host values on every
guest entry/exit.  Similarly, we don't need to worry about their
values on offline secondary threads since they execute in the context
of the idle task, which never executes in userspace.

Fixes: b005255e ("KVM: PPC: Book3S HV: Context-switch new POWER8 SPRs", 2014-01-08)
Cc: stable@vger.kernel.org # v3.14+
Signed-off-by: NPaul Mackerras <paulus@ozlabs.org>

POWER9 introduces a new mode for the decrementer register, called
large decrementer mode, in which the decrementer counter is 56 bits
wide rather than 32, and reads are sign-extended rather than
zero-extended.  For the decrementer, this new mode is optional and
controlled by a bit in the LPCR.  The hypervisor decrementer (HDEC)
is 56 bits wide on POWER9 and has no mode control.

Since KVM code reads and writes the decrementer and hypervisor
decrementer registers in a few places, it needs to be aware of the
need to treat the decrementer value as a 64-bit quantity, and only do
a 32-bit sign extension when large decrementer mode is not in effect.
Similarly, the HDEC should always be treated as a 64-bit quantity on
POWER9.  We define a new EXTEND_HDEC macro to encapsulate the feature
test for POWER9 and the sign extension.

To enable the sign extension to be removed in large decrementer mode,
we test the LPCR_LD bit in the host LPCR image stored in the struct
kvm for the guest.  If is set then large decrementer mode is enabled
and the sign extension should be skipped.

This is partly based on an earlier patch by Oliver O'Halloran.

Cc: stable@vger.kernel.org # v4.10+
Signed-off-by: NPaul Mackerras <paulus@ozlabs.org>

The code to fetch a 64-bit value from user space was entirely buggered,
and has been since the code was merged in early 2016 in commit
b2f68038 ("x86/mm/32: Add support for 64-bit __get_user() on 32-bit
kernels").

Happily the buggered routine is almost certainly entirely unused, since
the normal way to access user space memory is just with the non-inlined
"get_user()", and the inlined version didn't even historically exist.

The normal "get_user()" case is handled by external hand-written asm in
arch/x86/lib/getuser.S that doesn't have either of these issues.

There were two independent bugs in __get_user_asm_u64():

 - it still did the STAC/CLAC user space access marking, even though
   that is now done by the wrapper macros, see commit 11f1a4b9
   ("x86: reorganize SMAP handling in user space accesses").

   This didn't result in a semantic error, it just means that the
   inlined optimized version was hugely less efficient than the
   allegedly slower standard version, since the CLAC/STAC overhead is
   quite high on modern Intel CPU's.

 - the double register %eax/%edx was marked as an output, but the %eax
   part of it was touched early in the asm, and could thus clobber other
   inputs to the asm that gcc didn't expect it to touch.

   In particular, that meant that the generated code could look like
   this:

        mov    (%eax),%eax
        mov    0x4(%eax),%edx

   where the load of %edx obviously was _supposed_ to be from the 32-bit
   word that followed the source of %eax, but because %eax was
   overwritten by the first instruction, the source of %edx was
   basically random garbage.

The fixes are trivial: remove the extraneous STAC/CLAC entries, and mark
the 64-bit output as early-clobber to let gcc know that no inputs should
alias with the output register.

Cc: Al Viro <viro@zeniv.linux.org.uk>
Cc: Benjamin LaHaise <bcrl@kvack.org>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: stable@kernel.org   # v4.8+
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Al noticed that unsafe_put_user() had type problems, and fixed them in
commit a7cc722f ("fix unsafe_put_user()"), which made me look more
at those functions.

It turns out that unsafe_get_user() had a type issue too: it limited the
largest size of the type it could handle to "unsigned long".  Which is
fine with the current users, but doesn't match our existing normal
get_user() semantics, which can also handle "u64" even when that does
not fit in a long.

While at it, also clean up the type cast in unsafe_put_user().  We
actually want to just make it an assignment to the expected type of the
pointer, because we actually do want warnings from types that don't
convert silently.  And it makes the code more readable by not having
that one very long and complex line.

[ This patch might become stable material if we ever end up back-porting
  any new users of the unsafe uaccess code, but as things stand now this
  doesn't matter for any current existing uses. ]

Cc: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Pull misc uaccess fixes from Al Viro:
 "Fix for unsafe_put_user() (no callers currently in mainline, but
  anyone starting to use it will step into that) + alpha osf_wait4()
  infoleak fix"

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
  osf_wait4(): fix infoleak
  fix unsafe_put_user()

Pull scheduler fix from Thomas Gleixner:
 "A single scheduler fix:

  Prevent idle task from ever being preempted. That makes sure that
  synchronize_rcu_tasks() which is ignoring idle task does not pretend
  that no task is stuck in preempted state. If that happens and idle was
  preempted on a ftrace trampoline the machine crashes due to
  inconsistent state"

* 'sched-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  sched/core: Call __schedule() from do_idle() without enabling preemption

Pull irq fixes from Thomas Gleixner:
 "A set of small fixes for the irq subsystem:

   - Cure a data ordering problem with chained interrupts

   - Three small fixlets for the mbigen irq chip"

* 'irq-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  genirq: Fix chained interrupt data ordering
  irqchip/mbigen: Fix the clear register offset calculation
  irqchip/mbigen: Fix potential NULL dereferencing
  irqchip/mbigen: Fix memory mapping code

failing sys_wait4() won't fill struct rusage...

Cc: stable@vger.kernel.org
Signed-off-by: NAl Viro <viro@zeniv.linux.org.uk>

__put_user_size() relies upon its first argument having the same type as what
the second one points to; the only other user makes sure of that and
unsafe_put_user() should do the same.
Signed-off-by: NAl Viro <viro@zeniv.linux.org.uk>

Pull tracing fixes from Steven Rostedt:

 - Fix a bug caused by not cleaning up the new instance unique triggers
   when deleting an instance. It also creates a selftest that triggers
   that bug.

 - Fix the delayed optimization happening after kprobes boot up self
   tests being removed by freeing of init memory.

 - Comment kprobes on why the delay optimization is not a problem for
   removal of modules, to keep other developers from searching that
   riddle.

 - Fix another case of rcu not watching in stack trace tracing.

* tag 'trace-v4.12-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-trace:
  tracing: Make sure RCU is watching before calling a stack trace
  kprobes: Document how optimized kprobes are removed from module unload
  selftests/ftrace: Add test to remove instance with active event triggers
  selftests/ftrace: Fix bashisms
  ftrace: Remove #ifdef from code and add clear_ftrace_function_probes() stub
  ftrace/instances: Clear function triggers when removing instances
  ftrace: Simplify glob handling in unregister_ftrace_function_probe_func()
  tracing/kprobes: Enforce kprobes teardown after testing
  tracing: Move postpone selftests to core from early_initcall

Pull block fixes from Jens Axboe:
 "A small collection of fixes that should go into this cycle.

   - a pull request from Christoph for NVMe, which ended up being
     manually applied to avoid pulling in newer bits in master. Mostly
     fibre channel fixes from James, but also a few fixes from Jon and
     Vijay

   - a pull request from Konrad, with just a single fix for xen-blkback
     from Gustavo.

   - a fuseblk bdi fix from Jan, fixing a regression in this series with
     the dynamic backing devices.

   - a blktrace fix from Shaohua, replacing sscanf() with kstrtoull().

   - a request leak fix for drbd from Lars, fixing a regression in the
     last series with the kref changes. This will go to stable as well"

* 'for-linus' of git://git.kernel.dk/linux-block:
  nvmet: release the sq ref on rdma read errors
  nvmet-fc: remove target cpu scheduling flag
  nvme-fc: stop queues on error detection
  nvme-fc: require target or discovery role for fc-nvme targets
  nvme-fc: correct port role bits
  nvme: unmap CMB and remove sysfs file in reset path
  blktrace: fix integer parse
  fuseblk: Fix warning in super_setup_bdi_name()
  block: xen-blkback: add null check to avoid null pointer dereference
  drbd: fix request leak introduced by locking/atomic, kref: Kill kref_sub()

On rdma read errors, release the sq ref that was taken
when the req was initialized. This avoids a hang in
nvmet_sq_destroy() when the queue is being freed.
Signed-off-by: NVijay Immanuel <vijayi@attalasystems.com>
Reviewed-by: NSagi Grimberg <sagi@grimberg.me>
Signed-off-by: NChristoph Hellwig <hch@lst.de>
Signed-off-by: NJens Axboe <axboe@fb.com>

Remove NVMET_FCTGTFEAT_NEEDS_CMD_CPUSCHED. It's unnecessary.
Signed-off-by: NJames Smart <james.smart@broadcom.com>
Reviewed-by: NJohannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: NChristoph Hellwig <hch@lst.de>
Signed-off-by: NJens Axboe <axboe@fb.com>

Per the recommendation by Sagi on:
http://lists.infradead.org/pipermail/linux-nvme/2017-April/009261.html

Rather than waiting for reset work thread to stop queues and abort the ios,
immediately stop the queues on error detection. Reset thread will restop
the queues (as it's called on other paths), but it does not appear to have
a side effect.
Signed-off-by: NJames Smart <james.smart@broadcom.com>
Reviewed-by: NJohannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: NChristoph Hellwig <hch@lst.de>
Signed-off-by: NJens Axboe <axboe@fb.com>

In order to create an association, the remoteport must be
serving either a target role or a discovery role.
Signed-off-by: NJames Smart <james.smart@broadcom.com>
Reviewed-by: NJohannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: NChristoph Hellwig <hch@lst.de>
Signed-off-by: NJens Axboe <axboe@fb.com>

FC Port roles is a bit mask, not individual values.
Correct nvme definitions to unique bits.
Signed-off-by: NJames Smart <james.smart@broadcom.com>
Reviewed-by: NJohannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: NChristoph Hellwig <hch@lst.de>
Signed-off-by: NJens Axboe <axboe@fb.com>

CMB doesn't get unmapped until removal while getting remapped on every
reset. Add the unmapping and sysfs file removal to the reset path in
nvme_pci_disable to match the mapping path in nvme_pci_enable.

Fixes: 202021c1 ("nvme : Add sysfs entry for NVMe CMBs when appropriate")
Signed-off-by: NJon Derrick <jonathan.derrick@intel.com>
Acked-by: NKeith Busch <keith.busch@intel.com>
Reviewed-By: NStephen Bates <sbates@raithlin.com>
Cc: <stable@vger.kernel.org> # 4.9+
Signed-off-by: NChristoph Hellwig <hch@lst.de>
Signed-off-by: NJens Axboe <axboe@fb.com>

Pull staging driver fixes from Greg KH:
 "Here are a number of staging driver fixes for 4.12-rc2

  Most of them are typec driver fixes found by reviewers and users of
  the code. There are also some removals of files no longer needed in
  the tree due to the ion driver rewrite in 4.12-rc1, as well as some
  wifi driver fixes. And to round it out, a MAINTAINERS file update.

  All have been in linux-next with no reported issues"

* tag 'staging-4.12-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging: (22 commits)
  MAINTAINERS: greybus-dev list is members-only
  staging: fsl-dpaa2/eth: add ETHERNET dependency
  staging: typec: fusb302: refactor resume retry mechanism
  staging: typec: fusb302: reset i2c_busy state in error
  staging: rtl8723bs: remove re-positioned call to kfree in os_dep/ioctl_cfg80211.c
  staging: rtl8192e: GetTs Fix invalid TID 7 warning.
  staging: rtl8192e: rtl92e_get_eeprom_size Fix read size of EPROM_CMD.
  staging: rtl8192e: fix 2 byte alignment of register BSSIDR.
  staging: rtl8192e: rtl92e_fill_tx_desc fix write to mapped out memory.
  staging: vc04_services: Fix bulk cache maintenance
  staging: ccree: remove extraneous spin_unlock_bh() in error handler
  staging: typec: Fix sparse warnings about incorrect types
  staging: typec: fusb302: do not free gpio from managed resource
  staging: typec: tcpm: Fix Port Power Role field in PS_RDY messages
  staging: typec: tcpm: Respond to Discover Identity commands
  staging: typec: tcpm: Set correct flags in PD request messages
  staging: typec: tcpm: Drop duplicate PD messages
  staging: typec: fusb302: Fix chip->vbus_present init value
  staging: typec: fusb302: Fix module autoload
  staging: typec: tcpci: declare private structure as static
  ...

Pull USB fixes from Greg KH:
 "Here are a number of small USB fixes for 4.12-rc2

  Most of them come from Johan, in his valiant quest to fix up all
  drivers that could be affected by "malicious" USB devices. There's
  also some fixes for more "obscure" drivers to handle some of the
  vmalloc stack fallout (which for USB drivers, was always the case, but
  very few people actually ran those systems...)

  Other than that, the normal set of xhci and gadget and musb driver
  fixes as well.

  All have been in linux-next with no reported issues"

* tag 'usb-4.12-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (42 commits)
  usb: musb: tusb6010_omap: Do not reset the other direction's packet size
  usb: musb: Fix trying to suspend while active for OTG configurations
  usb: host: xhci-plat: propagate return value of platform_get_irq()
  xhci: Fix command ring stop regression in 4.11
  xhci: remove GFP_DMA flag from allocation
  USB: xhci: fix lock-inversion problem
  usb: host: xhci-ring: don't need to clear interrupt pending for MSI enabled hcd
  usb: host: xhci-mem: allocate zeroed Scratchpad Buffer
  xhci: apply PME_STUCK_QUIRK and MISSING_CAS quirk for Denverton
  usb: xhci: trace URB before giving it back instead of after
  USB: serial: qcserial: add more Lenovo EM74xx device IDs
  USB: host: xhci: use max-port define
  USB: hub: fix SS max number of ports
  USB: hub: fix non-SS hub-descriptor handling
  USB: hub: fix SS hub-descriptor handling
  USB: usbip: fix nonconforming hub descriptor
  USB: gadget: dummy_hcd: fix hub-descriptor removable fields
  doc-rst: fixed kernel-doc directives in usb/typec.rst
  USB: core: of: document reference taken by companion helper
  USB: ehci-platform: fix companion-device leak
  ...

Pull char/misc driver fixes from Greg KH:
 "Here are five small bugfixes for reported issues with 4.12-rc1 and
  earlier kernels. Nothing huge here, just a lp, mem, vpd, and uio
  driver fix, along with a Kconfig fixup for one of the misc drivers.

  All of these have been in linux-next with no reported issues"

* tag 'char-misc-4.12-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc:
  firmware: Google VPD: Fix memory allocation error handling
  drivers: char: mem: Check for address space wraparound with mmap()
  uio: fix incorrect memory leak cleanup
  misc: pci_endpoint_test: select CRC32
  char: lp: fix possible integer overflow in lp_setup()

Pull watchdog fixes from Wim Van Sebroeck:
 - orion_wdt compile-test dependencies
 - sama5d4_wdt: WDDIS handling and a race confition
 - pcwd_usb: fix NULL-deref at probe
 - cadence_wdt: fix timeout setting
 - wdt_pci: fix build error if SOFTWARE_REBOOT is defined
 - iTCO_wdt: all versions count down twice
 - zx2967: remove redundant dev_err call in zx2967_wdt_probe()
 - bcm281xx: Fix use of uninitialized spinlock

* git://www.linux-watchdog.org/linux-watchdog:
  watchdog: bcm281xx: Fix use of uninitialized spinlock.
  watchdog: zx2967: remove redundant dev_err call in zx2967_wdt_probe()
  iTCO_wdt: all versions count down twice
  watchdog: wdt_pci: fix build error if define SOFTWARE_REBOOT
  watchdog: cadence_wdt: fix timeout setting
  watchdog: pcwd_usb: fix NULL-deref at probe
  watchdog: sama5d4: fix race condition
  watchdog: sama5d4: fix WDDIS handling
  watchdog: orion: fix compile-test dependencies

Pull drm fixes from Dave Airlie:
 "Mostly nouveau and i915, fairly quiet as usual for rc2"

* tag 'drm-fixes-for-v4.12-rc2' of git://people.freedesktop.org/~airlied/linux:
  drm/atmel-hlcdc: Fix output initialization
  gpu: host1x: select IOMMU_IOVA
  drm/nouveau/fifo/gk104-: Silence a locking warning
  drm/nouveau/secboot: plug memory leak in ls_ucode_img_load_gr() error path
  drm/nouveau: Fix drm poll_helper handling
  drm/i915: don't do allocate_va_range again on PIN_UPDATE
  drm/i915: Fix rawclk readout for g4x
  drm/i915: Fix runtime PM for LPE audio
  drm/i915/glk: Fix DSI "*ERROR* ULPS is still active" messages
  drm/i915/gvt: avoid unnecessary vgpu switch
  drm/i915/gvt: not to restore in-context mmio
  drm/etnaviv: don't put fence in case of submit failure
  drm/i915/gvt: fix typo: "supporte" -> "support"
  drm: hdlcd: Fix the calculation of the scanout start address

Pull SCSI fixes from James Bottomley:
 "This is the first sweep of mostly minor fixes. There's one security
  one: the read past the end of a buffer in qedf, and a panic fix for
  lpfc SLI-3 adapters, but the rest are a set of include and build
  dependency tidy ups and assorted other small fixes and updates"

* tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
  scsi: pmcraid: remove redundant check to see if request_size is less than zero
  scsi: lpfc: ensure els_wq is being checked before destroying it
  scsi: cxlflash: Select IRQ_POLL
  scsi: qedf: Avoid reading past end of buffer
  scsi: qedf: Cleanup the type of io_log->op
  scsi: lpfc: double lock typo in lpfc_ns_rsp()
  scsi: qedf: properly update arguments position in function call
  scsi: scsi_lib: Add #include <scsi/scsi_transport.h>
  scsi: MAINTAINERS: update OSD entries
  scsi: Skip deleted devices in __scsi_device_lookup
  scsi: lpfc: Fix panic on BFS configuration
  scsi: libfc: do not flood console with messages 'libfc: queue full ...'

Pull libnvdimm fixes from Dan Williams:
 "A couple of compile fixes.

  With the removal of the ->direct_access() method from
  block_device_operations in favor of a new dax_device + dax_operations
  we broke two configurations.

  The CONFIG_BLOCK=n case is fixed by compiling out the block+dax
  helpers in the dax core. Configurations with FS_DAX=n EXT4=y / XFS=y
  and DAX=m fail due to the helpers the builtin filesystem needs being
  in a module, so we stub out the helpers in the FS_DAX=n case."

* 'libnvdimm-for-next' of git://git.kernel.org/pub/scm/linux/kernel/git/nvdimm/nvdimm:
  dax, xfs, ext4: compile out iomap-dax paths in the FS_DAX=n case
  dax: fix false CONFIG_BLOCK dependency

Pull i2c fix from Wolfram Sang:
 "A regression fix for I2C that would be great to have in rc2"

* 'i2c/for-current' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux:
  i2c: designware: don't infer timings described by ACPI from clock rate

Pull IOMMU fixes from Joerg Roedel:

 - another compile-fix as a fallout of the recent header-file cleanup

 - add a missing IO/TLB flush to the Intel VT-d kdump code path

 - a fix for ARM64 dma code to only access initialized iova_domain
   members

* tag 'iommu-fixes-v4.12-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/joro/iommu:
  iommu/mediatek: Include linux/dma-mapping.h
  iommu/vt-d: Flush the IOTLB to get rid of the initial kdump mappings
  iommu/dma: Don't touch invalid iova_domain members

Pull KVM fixes from Radim Krčmář:
 "ARM:
   - a fix for a build failure introduced in -rc1 when tracepoints are
     enabled on 32-bit ARM.

   - disable use of stack pointer protection in the hyp code which can
     cause panics.

   - a handful of VGIC fixes.

   - a fix to the init of the redistributors on GICv3 systems that
     prevented boot with kvmtool on GICv3 systems introduced in -rc1.

   - a number of race conditions fixed in our MMU handling code.

   - a fix for the guest being able to program the debug extensions for
     the host on the 32-bit side.

  PPC:
   - fixes for build failures with PR KVM configurations.

   - a fix for a host crash that can occur on POWER9 with radix guests.

  x86:
   - fixes for nested PML and nested EPT.

   - a fix for crashes caused by reserved bits in SSE MXCSR that could
     have been set by userspace.

   - an optimization of halt polling that fixes high CPU overhead.

   - fixes for four reports from Dan Carpenter's static checker.

   - a protection around code that shouldn't have been preemptible.

   - a fix for port IO emulation"

* tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm: (27 commits)
  KVM: x86: prevent uninitialized variable warning in check_svme()
  KVM: x86/vPMU: fix undefined shift in intel_pmu_refresh()
  KVM: x86: zero base3 of unusable segments
  KVM: X86: Fix read out-of-bounds vulnerability in kvm pio emulation
  KVM: x86: Fix potential preemption when get the current kvmclock timestamp
  KVM: Silence underflow warning in avic_get_physical_id_entry()
  KVM: arm/arm64: Hold slots_lock when unregistering kvm io bus devices
  KVM: arm/arm64: Fix bug when registering redist iodevs
  KVM: x86: lower default for halt_poll_ns
  kvm: arm/arm64: Fix use after free of stage2 page table
  kvm: arm/arm64: Force reading uncached stage2 PGD
  KVM: nVMX: fix EPT permissions as reported in exit qualification
  KVM: VMX: Don't enable EPT A/D feature if EPT feature is disabled
  KVM: x86: Fix load damaged SSEx MXCSR register
  kvm: nVMX: off by one in vmx_write_pml_buffer()
  KVM: arm: rename pm_fake handler to trap_raz_wi
  KVM: arm: plug potential guest hardware debug leakage
  kvm: arm/arm64: Fix race in resetting stage2 PGD
  KVM: arm/arm64: vgic-v3: Use PREbits to infer the number of ICH_APxRn_EL2 registers
  KVM: arm/arm64: vgic-v3: Do not use Active+Pending state for a HW interrupt
  ...