Clean up existing Errata 1p153 handling to use generic
errata handling mechanism through dev flag.
Signed-off-by: NManjunatha GK <manjugk@ti.com>
Cc: Nishanth Menon <nm@ti.com>
Cc: Alexander Shishkin <virtuoso@slind.org>
Signed-off-by: NTony Lindgren <tony@atomide.com>
Signed-off-by: NBen Dooks <ben-linux@fluff.org>

Under certain rare conditions, I2C_STAT[13].RDR bit may be set
and the corresponding interrupt fire, even there is no data in
the receive FIFO, or the I2C data transfer is still ongoing.
These spurious RDR events must be ignored by the software.

This patch handles and ignores RDR spurious interrupts.

The below sequence is required in interrupt handler for
handling this errata:
1. If RDR is set to 1, clear RDR
2. Read I2C status register and check for BusBusy bit. If BusBusy
bit is set, skip remaining steps.
3. If BusBusy bit is not set, perform read operation on I2C status
register.
4. If RDR is set, clear the same. Check RDR again and clear if it sets
RDR bit again.
5. Perform I2C Data Read operation N number of times(where N is value
read from the register BUFSTAT-RXSTAT bit fields).

Note:
This errata is not applicable for omap2420 and omap4.
It is applicable for:
1. omap2430
2. omap34xx(including omap3630).
Signed-off-by: NManjunatha GK <manjugk@ti.com>
Cc: Hema Kalliguddi <hemahk@ti.com>
Cc: Nishanth Menon <nm@ti.com>
Cc: Aaro Koskinen <Aaro.Koskinen@nokia.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>
Signed-off-by: NBen Dooks <ben-linux@fluff.org>

The errata 1.153 workaround is busy waiting on XUDF bit in interrupt
context, which may lead to kernel hangs. The problem can be reproduced
by running the bus with wrong (too high) speed.
Signed-off-by: NAlexander Shishkin <virtuoso@slind.org>
Signed-off-by: NTony Lindgren <tony@atomide.com>
Signed-off-by: NBen Dooks <ben-linux@fluff.org>

This is to avoid insanely long lines and levels of indentation.
Signed-off-by: NAlexander Shishkin <virtuoso@slind.org>
Cc: Nishant Menon <nm@ti.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>
Signed-off-by: NBen Dooks <ben-linux@fluff.org>

While waiting for completion of the i2c transfer, the
MPU could hit OFF mode and cause several msecs of
delay that made i2c transfers fail more often. The
extra delays and subsequent re-trys cause i2c clocks
to be active more often. This has also an negative
effect on power consumption.

Created a mechanism for passing and using the
constraint setting function in driver code. The used
mpu wake up latency constraints are now set individually
per bus, and they are calculated based on clock rate
and fifo size.

Thanks to Jarkko Nikula, Moiz Sonasath, Paul Walmsley,
and Nishanth Menon for tuning out the details of
this patch.

Updates by Kevin as requested by Tony:

- Remove omap_set_i2c_constraint_func() in favor of conditionally
  adding the flag in omap_i2c_add_bus() in order to keep all the OMAP
  conditional checking in a single location.
- Update set_mpu_wkup_lat prototypes to match OMAP PM layer so
  OMAP PM function can be used directly in pdata.

Cc: Moiz Sonasath <m-sonasath@ti.com>
Cc: Jarkko Nikula <jhnikula@gmail.com>
Cc: Paul Walmsley <paul@pwsan.com>
Cc: Nishanth Menon <nm@ti.com>
Signed-off-by: NKalle Jokiniemi <kalle.jokiniemi@digia.com>
Signed-off-by: NKevin Hilman <khilman@deeprootsystems.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>
Signed-off-by: NBen Dooks <ben-linux@fluff.org>

This patch is rebased version of earlier post to add I2C
driver support to OMAP4 platform. On OMAP4, all
I2C register address offsets are changed from OMAP1/2/3 I2C.
In order to not have #ifdef's at various places in code,
as well as to support multi-OMAP build, an array is created
to hold the register addresses with it's offset.

This patch was submitted, reviewed and acked on mailing list
already. For more details refer below link
http://www.mail-archive.com/linux-i2c@vger.kernel.org/msg02281.html

This updated verion has a depedancy on "Add support for 16-bit registers"
posted on linux-omap. Below is the patch-works link for the same

http://patchwork.kernel.org/patch/72295/Signed-off-by: NSyed Rafiuddin <rafiuddin.syed@ti.com>
Signed-off-by: NSantosh Shilimkar <santosh.shilimkar@ti.com>
Acked-by: NKevin Hilman <khilman@deeprootsystems.com>
Reviewed-by: NPaul Walmsley <paul@pwsan.com>
Cc: Cory Maccarrone <darkstar6262@gmail.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>
Signed-off-by: NBen Dooks <ben-linux@fluff.org>

A smbus quick transfer has no data after the address byte.
Signed-off-by: NSonic Zhang <sonic.zhang@analog.com>
Signed-off-by: NMike Frysinger <vapier@gentoo.org>
Signed-off-by: NBen Dooks <ben-linux@fluff.org>

Signed-off-by: NSonic Zhang <sonic.zhang@analog.com>
Signed-off-by: NMike Frysinger <vapier@gentoo.org>
Signed-off-by: NBen Dooks <ben-linux@fluff.org>

i2c event of next read/write byte may trigger before current int state
is cleared in the interrupt handler. So, this should be done at the
beginning of interrupt handler to avoid losing new i2c events.
Signed-off-by: NSonic Zhang <sonic.zhang@analog.com>
Signed-off-by: NMike Frysinger <vapier@gentoo.org>
Signed-off-by: NBen Dooks <ben-linux@fluff.org>

Add some debug() code to decode the error register.
Signed-off-by: NMichael Hennerich <michael.hennerich@analog.com>
Signed-off-by: NMike Frysinger <vapier@gentoo.org>
Signed-off-by: NBen Dooks <ben-linux@fluff.org>

There isn't much point in managing our own custom timeout timer when the
completion interface already includes support for it.  This makes the
resulting code much simpler and robust.
Signed-off-by: NSonic Zhang <sonic.zhang@analog.com>
Signed-off-by: NMike Frysinger <vapier@gentoo.org>
Signed-off-by: NBen Dooks <ben-linux@fluff.org>

The S3C I2C controller indicates completion of I2C transfers before
the bus has a stop condition on it. In order to ensure that we do not
attempt to start a new transfer before the bus is idle the driver
currently inserts a 1ms delay. This is vastly larger than is generally
required and has a visible effect on performance under load, such as
when bringing up audio CODECs or reading back status information with
non-bulk I2C reads.

Replace the sleep with a spin on the IIC status register for up to 1ms.
This will busy wait but testing on my SMDK6410 system indicates that
the overwhelming majority of transactions complete on the first spin,
with maximum latencies of less than 10 spins so the absolute overhead
of busy waiting should be at worst comprable to msleep(), and the
overall system performance is dramatically improved.

The main risk is poor interaction with multimaster systems where
we may miss the bus going idle before the next transaction. Defend
against this by falling back to the original 1ms delay after 20 spins.

The overall effect in my testing is an approximately 20% improvement
in kernel startup time.
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: NBen Dooks <ben-linux@fluff.org>

Merge branch 'davinci-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/khilman/linux-davinci

* 'davinci-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/khilman/linux-davinci: (48 commits)
  Revert "rtc: omap: let device wakeup capability be configured from chip init logic"
  DM365: Added more PINMUX configurations for AEMIF
  DM365: Make CLKOUTx available
  DM365: Added PINMUX definitions for GPIO30..32
  Davinci: iotable based ioremap() interception
  Davinci: pinmux - use ioremap()
  Davinci: aintc/cpintc - use ioremap()
  Davinci: psc - use ioremap()
  Davinci: timer - use ioremap()
  Davinci: jtag_id - use ioremap()
  Davinci: da8xx: rtc - use ioremap
  Davinci: gpio - use ioremap()
  davinci: edma: fix coding style issue related to breaking lines
  davinci: edma: use BIT() wherever possible
  davinci: edma: fix coding style issue related to usage of braces
  davinci: edma: use a more intuitive name for edma_info
  Davinci: serial - conditional reset via pwremu
  Davinci: serial - use ioremap()
  Davinci: serial - remove unnecessary define
  Davinci: watchdog reset separation across socs
  ...

Fix up trivial conflict in arch/arm/Kconfig due to removal of "select
GENERIC_TIME"

* 'for-linus/samsung4' of git://git.fluff.org/bjdooks/linux: (98 commits)
  Input: s3c24xx_ts - depend on SAMSUNG_DEV_TS and update menu entry
  Input: s3c24xx_ts - Add FEAT for Samsung touchscreen support
  Input: s3c24xx_ts - Implement generic GPIO configuration callback
  ARM: SAMSUNG: Move s3c64xx dev-ts.c to plat-samsung and rename configuration
  ARM: SAMSUNG: Implements cfg_gpio function for Samsung touchscreen
  ARM: S3C64XX: Add touchscreen platform device definition
  ARM: SAMSUNG: Move mach/ts.h to plat/ts.h
  ARM: S5PC100: Move i2c helpers from plat-s5pc1xx to mach-s5pc100
  ARM: S5PC100: Move frame buffer helpers from plat-s5pc1xx to mach-s5pc100
  ARM: S5PC100: gpio.h cleanup
  ARM: S5PC100: Move gpio support from plat-s5pc1xx to mach-s5pc100
  ARM: S5PC100: Use common functions for gpiolib implementation
  drivers: serial: S5PC100 serial driver cleanup
  ARM: S5PC100: Pre-requisite clock patch for plat-s5pc1xx to plat-s5p move
  ARM: SAMSUNG: Copy common I2C0 device helpers to machine directories
  ARM: SAMSUNG: move driver strength gpio configuration helper to common dir
  ARM: S5PV210: Add GPIOlib support
  ARM: SAMSUNGy: fix broken timer irq base
  ARM: SMDK6440: Add audio devices on board
  ARM: S5P6440: Add audio platform devices
  ...

Commit a45185d2 "cpumask: convert kernel/compat.c" broke libnuma, which
abuses sched_getaffinity to find out NR_CPUS in order to parse
/sys/devices/system/node/node*/cpumap.

On NUMA systems with less than 32 possibly CPUs, the current
compat_sys_sched_getaffinity now returns '4' instead of the actual
NR_CPUS/8, which makes libnuma bail out when parsing the cpumap.

The libnuma call sched_getaffinity(0, bitmap, 4096) at first.  It mean
the libnuma expect the return value of sched_getaffinity() is either len
argument or NR_CPUS.  But it doesn't expect to return nr_cpu_ids.

Strictly speaking, userland requirement are

1) Glibc assume the return value mean the lengh of initialized
   of mask argument. E.g. if sched_getaffinity(1024) return 128,
   glibc make zero fill rest 896 byte.
2) Libnuma assume the return value can be used to guess NR_CPUS
   in kernel. It assume len-arg<NR_CPUS makes -EINVAL. But
   it try len=4096 at first and 4096 is always bigger than
   NR_CPUS. Then, if we remove strange min_length normalization,
   we never hit -EINVAL case.

sched_getaffinity() already solved this issue.  This patch adapts
compat_sys_sched_getaffinity() to match the non-compat case.
Signed-off-by: NKOSAKI Motohiro <kosaki.motohiro@jp.fujitsu.com>
Acked-by: NRusty Russell <rusty@rustcorp.com.au>
Acked-by: NArnd Bergmann <arnd@arndb.de>
Reported-by: NKen Werner <ken.werner@web.de>
Cc: stable@kernel.org
Cc: Andi Kleen <andi@firstfloor.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

* 'release' of git://git.kernel.org/pub/scm/linux/kernel/git/aegl/linux-2.6:
  [IA64] Drop duplicated "config IOMMU_HELPER"
  [IA64] invoke oom-killer from page fault
  [IA64] use __ratelimit
  [IA64] Use set_cpus_allowed_ptr
  [IA64] Use set_cpus_allowed_ptr
  [IA64] arch/ia64/hp/common/sba_iommu.c: Rename dev_info to adi
  [IA64] removing redundant ifdef

* 'devel' of master.kernel.org:/home/rmk/linux-2.6-arm: (224 commits)
  ARM: remove 'select GENERIC_TIME'
  ARM: 6136/1: ARCH_REQUIRE_GPIOLIB selects GENERIC_GPIO
  ARM: 6074/1: oprofile: convert from sysdev to platform device
  ARM: 6073/1: oprofile: remove old files and update KConfig
  ARM: 6072/1: oprofile: use perf-events framework as backend
  ARM: 6071/1: perf-events: allow modules to query the number of hardware counters
  ARM: 6070/1: perf-events: add support for xscale PMUs
  ARM: 6069/1: perf-events: use numeric ID to identify PMU
  ARM: 6064/1: pmu: register IRQs at runtime
  ARM: Optionally allow ARMv6 to use 'normal, bufferable' memory for DMA
  ARM: 6134/1: Handle instruction cache maintenance fault properly
  ARM: nwfpe: allow debugging output to be configured at runtime
  ARM: rename mach_cpu_disable() to platform_cpu_disable()
  ARM: 6132/1: PL330: Add common core driver
  ARM: 6094/1: Extend cache-l2x0 to support the 16-way PL310
  ARM: Move memory mapping into mmu.c
  ARM: Ensure meminfo is sorted prior to sanity_check_meminfo
  ARM: Remove useless linux/bootmem.h includes
  ARM: convert /proc/cpu/aligment to seq_file
  arm: use asm-generic/scatterlist.h
  ...

This reverts commit 9c0a342c because
it was included without proper signoffs from RTC maintainers.

* git://git.kernel.org/pub/scm/linux/kernel/git/lethal/sh-2.6: (127 commits)
  sh: update defconfigs.
  sh: Fix up the NUMA build for recent LMB changes.
  sh64: provide a stub per_cpu_trap_init() definition.
  sh: fix up CONFIG_KEXEC=n build.
  sh: fixup the docbook paths for clock framework shuffling.
  driver core: Early dev_name() depends on slab_is_available().
  sh: simplify WARN usage in SH clock driver
  sh: Check return value of clk_get on ms7724
  sh: Check return value of clk_get on ecovec24
  sh: move sh clock-cpg.c contents to drivers/sh/clk-cpg.c
  sh: move sh clock.c contents to drivers/sh/clk.
  sh: move sh asm/clock.h contents to linux/sh_clk.h V2
  sh: remove unused clock lookup
  sh: switch boards to clkdev
  sh: switch sh4-202 to clkdev
  sh: switch shx3 to clkdev
  sh: switch sh7757 to clkdev
  sh: switch sh7763 to clkdev
  sh: switch sh7780 to clkdev
  sh: switch sh7786 to clkdev
  ...

* 'for-linus' of git://git390.marist.edu/pub/scm/linux-2.6: (24 commits)
  [S390] drivers/s390/char: Use kmemdup
  [S390] drivers/s390/char: Use kstrdup
  [S390] debug: enable exception-trace debug facility
  [S390] s390_hypfs: Add new attributes
  [S390] qdio: remove API wrappers
  [S390] qdio: set correct bit in dsci
  [S390] qdio: dont convert timestamps to microseconds
  [S390] qdio: remove memset hack
  [S390] qdio: prevent starvation on PCI devices
  [S390] qdio: count number of qdio interrupts
  [S390] user space fault: report fault before calling do_exit
  [S390] topology: expose core identifier
  [S390] dasd: remove uid from devmap
  [S390] dasd: add dynamic pav toleration
  [S390] vdso: add missing vdso_install target
  [S390] vdso: remove redundant check for CONFIG_64BIT
  [S390] avoid default_llseek in s390 drivers
  [S390] vmcp: disallow modular build
  [S390] add breaking event address for user space
  [S390] virtualization aware cpu measurement
  ...

Make the driver depend on either ARCH_S3C2410 (as legacy) or the new
device selection of SAMSUNG_DEV_TS.

Change the menuconfig name to reflect this driver is now handling more
devices that just the s3c2410.
Signed-off-by: NBen Dooks <ben-linux@fluff.org>
Acked-by: NDmitry Torokhov <dtor@mail.ru>

This patch adds a feature bit field in the touchscreen driver for Samsung SoCs.
Which can be used to distinguish the TSADC module features.
Signed-off-by: NNaveen Krishna Ch <ch.naveen@samsung.com>
Signed-off-by: NKukjin Kim <kgene.kim@samsung.com>
[ben-linux@fluff.org: minor fix to title]
Signed-off-by: NBen Dooks <ben-linux@fluff.org>
Acked-by: NDmitry Torokhov <dtor@mail.ru>

This patch implements generic GPIO configuration function in Samsung
touchscreen driver. And makes the touchscreen driver s3c24xx-ts.c
generic to all the Samsung SoCs.
Signed-off-by: NNaveen Krishna Ch <ch.naveen@samsung.com>
Signed-off-by: NKukjin Kim <kgene.kim@samsung.com>
[ben-linux@fluff.org: fixed title ]
Signed-off-by: NBen Dooks <ben-linux@fluff.org>
Acked-by: NDmitry Torokhov <dtor@mail.ru>

Move the arch/arm/mach-s3c64xx/dev-ts.c file to arch/arm/plat-samsung and
rename the Kconfig entry appropriately.
Signed-off-by: NBen Dooks <ben-linux@fluff.org>

This patch implements cfg_gpio function for Samsung touchscreen.
And also modifies the H1940 machine respectively.
Signed-off-by: NNaveen Krishna Ch <ch.naveen@samsung.com>
Signed-off-by: NKukjin Kim <kgene.kim@samsung.com>
Signed-off-by: NBen Dooks <ben-linux@fluff.org>

This patch adds the touchscreen platform device definition for S3C64XX boards.
Signed-off-by: NMaurus Cuelenaere <mcuelenaere@gmail.com>
Signed-off-by: NBen Dooks <ben-linux@fluff.org>

This moves mach-s3c2410/include/mach/ts.h to plat-samsung/include/plat/ts.h in
order to prepare for s3c64xx support in the touchscreen driver.
Signed-off-by: NMaurus Cuelenaere <mcuelenaere@gmail.com>
Signed-off-by: NBen Dooks <ben-linux@fluff.org>

Move i2c helpers from plat-s5pc1xx to mach-s5pc100.
Signed-off-by: NMarek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: NKyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: NBen Dooks <ben-linux@fluff.org>

Move frame buffer helpers from plat-s5pc1xx to mach-s5pc100.
Signed-off-by: NMarek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: NKyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: NBen Dooks <ben-linux@fluff.org>

This patch renames gpio related registers from s5pc1xx to s5pc100 to
better match the plat-s5p framework style. GPIO_MP* defines now used
anywhere thus has been removed.
Signed-off-by: NMarek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: NKyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: NBen Dooks <ben-linux@fluff.org>

Move gpio-lib support from plat-s5pc1xx to mach-s5pc100. Only basic gpio
functionality is now supported. Gpio interrupts are disabled temporarly
and will be added later.
Signed-off-by: NMarek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: NKyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: NBen Dooks <ben-linux@fluff.org>

GPIOlib helpers from plat-samsung already have functions for accessing
4bit gpio banks. This patch removes the duplicated functions from
plat-s5pc1xx/gpiolib.c.
Signed-off-by: NMarek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: NKyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: NBen Dooks <ben-linux@fluff.org>

Remove unnecessary Kconfig entry. S5PC100 has exactly the same driver as
S3C6400/S3C6410/S5P6440.
Signed-off-by: NMarek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: NKyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: NBen Dooks <ben-linux@fluff.org>

This is a pre-requisite clock patch for the plat-s5pc1xx to plat-s5p
movement. The patches that perform the movement of the code from
plat-s5pc1xx to plat-s5p (and mach-s5pc100) should also enable the
build for the mach-s5pc100/clock.c code.
Signed-off-by: NThomas Abraham <thomas.ab@samsung.com>
Signed-off-by: NKukjin Kim <kgene.kim@samsung.com>
Signed-off-by: NBen Dooks <ben-linux@fluff.org>

Signed-off-by: NMarek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: NKyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: NBen Dooks <ben-linux@fluff.org>

Driver strength parameter can be changed not only on S5PC100 but also
on S5PV210/S5PC110 platforms, so move the helper functions to the common
plat-samsung directory.
Signed-off-by: NMarek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: NKyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: NBen Dooks <ben-linux@fluff.org>

Merge branch 'for-2635/samsung-rtc' into for-linus/samsung2

Conflicts:
	arch/arm/mach-s3c64xx/include/mach/map.h
	arch/arm/plat-samsung/Kconfig
	arch/arm/plat-samsung/Makefile

Merge branch 'for-2635/samsung-ts' into for-linus/samsung2

Merge branch 'for-2635/s5p-audio' into for-linus/samsung2

Merge branch 'for-2635/s5p-dma' into for-linus/samsung2

Conflicts:
	arch/arm/mach-s5pv210/Makefile