This patch moves cpufreq driver of ARM based davinci platform to
drivers/cpufreq.
Signed-off-by: NViresh Kumar <viresh.kumar@linaro.org>
Acked-by: NSekhar Nori <nsekhar@ti.com>
Acked-by: NArnd Bergmann <arnd@arndb.de>
Signed-off-by: NRafael J. Wysocki <rafael.j.wysocki@intel.com>

This patch moves cpufreq driver of ARM based tegra platform to drivers/cpufreq.
Signed-off-by: NViresh Kumar <viresh.kumar@linaro.org>
Acked-by: NStephen Warren <swarren@nvidia.com>
Tested-by: NStephen Warren <swarren@nvidia.com>
Acked-by: NArnd Bergmann <arnd@arndb.de>
Signed-off-by: NRafael J. Wysocki <rafael.j.wysocki@intel.com>

Normally we keep drivers in alphabetical inside Kconfig and Makefile and over
time this was broken for ARM cpufreq drivers. Fix it.
Signed-off-by: NViresh Kumar <viresh.kumar@linaro.org>
Acked-by: NStephen Warren <swarren@nvidia.com>
Tested-by: NStephen Warren <swarren@nvidia.com>
Acked-by: NArnd Bergmann <arnd@arndb.de>
Signed-off-by: NRafael J. Wysocki <rafael.j.wysocki@intel.com>

big LITTLE is ARM's new Architecture focussing power/performance needs of modern
world. More information about big LITTLE can be found here:

http://www.arm.com/products/processors/technologies/biglittleprocessing.php
http://lwn.net/Articles/481055/

In order to keep cpufreq support for all big LITTLE platforms simple/generic,
this patch tries to add a generic cpufreq driver layer for all big LITTLE
platforms.

The driver is divided into two parts:
- Core driver: Generic and shared across all big LITTLE SoC's
- Glue drivers: Per platform drivers providing ops to the core driver

This patch adds in a generic glue driver which would extract information from
Device Tree.

Future SoC's can either reuse the DT glue or write their own depending on the
need.
Signed-off-by: NSudeep KarkadaNagesha <sudeep.karkadanagesha@arm.com>
Signed-off-by: NViresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: NRafael J. Wysocki <rafael.j.wysocki@intel.com>

The Marvell Kirkwood SoCs have simple cpufreq support in hardware. The
CPU can either use the a high speed cpu clock, or the slower DDR
clock. Add a driver to swap between these two clock sources.
Signed-off-by: NAndrew Lunn <andrew@lunn.ch>
Acked-by: NJason Cooper <jason@lakedaemon.net>
Acked-by: NViresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: NRafael J. Wysocki <rafael.j.wysocki@intel.com>

Add a P-state driver for the Intel Sandy bridge processor. In cpufreq
terminology this driver implements a  scaling driver with an internal
governor.

When built into the the kernel this driver will be the preferred
scaling driver for Sandy bridge processors.

In addition to the interfaces provided by the cpufreq subsystem for
controlling scaling drivers. The user may control the behavior of the
driver via three sysfs files located in
"/sys/devices/system/cpu/intel_pstate".

  max_perf_pct: limits the maximum P state that will be requested by
  the driver stated as a percentage of the avail performance.

  min_perf_pct: limits the minimum P state that will be  requested by
  the driver stated as a percentage of the avail performance.

  no_turbo: limits the driver to selecting P states below the turbo
  frequency range.
Signed-off-by: NDirk Brandewie <dirk.j.brandewie@intel.com>
Acked-by: NViresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: NRafael J. Wysocki <rafael.j.wysocki@intel.com>

Add an imx6q-cpufreq driver for Freescale i.MX6Q SoC to handle the
hardware specific frequency and voltage scaling requirements.

The driver supports module build and is instantiated by the platform
device/driver mechanism, so that it will not be instantiated on other
platforms, as IMX is built with multiplatform support.
Signed-off-by: NShawn Guo <shawn.guo@linaro.org>
Reviewed-by: NViresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: NRafael J. Wysocki <rafael.j.wysocki@intel.com>

Highbank processors depend on the external ECME to perform voltage
management based on a requested frequency. Communication between the
A9 cores and the ECME happens over the pl320 IPC channel.
Signed-off-by: NMark Langsdorf <mark.langsdorf@calxeda.com>
Reviewed-by: NShawn Guo <shawn.guo@linaro.org>
Reviewed-by: NMike Turquette <mturquette@linaro.org>
Signed-off-by: NRafael J. Wysocki <rafael.j.wysocki@intel.com>

Now that the majority of x86 CPUs out there are supported by
acpi-cpufreq, we want it to load first and, in the AMD case, drop to
powernow-k8 only on K8s. If, however, both powernow-k8 and acpi-cpufreq
are built-in, the link order matters. Correct that.
Signed-off-by: NBorislav Petkov <bp@suse.de>
Signed-off-by: NRafael J. Wysocki <rafael.j.wysocki@intel.com>

This driver doesn't only handle cpufreq functionality for the
db8500 anymore. There are new variants which rely on it too.
Let's make the name a bit more generic.
Signed-off-by: NLee Jones <lee.jones@linaro.org>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>
Acked-by: NRafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>

Since commit 2aacdfff entitled "cpufreq: Move common part from governors
to separate file", whenever the drivers that depend on this new file
(cpufreq_ondemand or cpufreq_conservative) are built as modules, a new
module named cpufreq_governor is created because the Makefile includes
cpufreq_governor.o twice. As drivers/cpufreq/cpufreq_governor.c contains no
MODULE directives, the resulting module has no license specified, which
results in logging of a "module license 'unspecified' taints kernel". In
addition, a number of globals are exported GPL only, and are therefore
not available. This fix establishes a new boolean configuration variable
that forces cpufreq_governor.o to be linked into the kernel whenever
either cpufreq_ondemand or cpufreq_conservative is selected.
Signed-off-by: NLarry Finger <Larry.Finger@lwfinger.net>
Reviewed-by: NViresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: NRafael J. Wysocki <rafael.j.wysocki@intel.com>

SPEAr is an ARM based family of SoCs. This patch adds in support of cpufreq
driver for SPEAr SoCs. It is supported via DT only and so bindings are present
in binding document.
Signed-off-by: NDeepak Sikri <deepak.sikri@st.com>
Signed-off-by: NViresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: NRafael J. Wysocki <rafael.j.wysocki@intel.com>

Multiple cpufreq governers have defined similar get_cpu_idle_time_***()
routines. These routines must be moved to some common place, so that all
governors can use them.

So moving them to cpufreq_governor.c, which seems to be a better place for
keeping these routines.
Signed-off-by: NViresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: NRafael J. Wysocki <rafael.j.wysocki@intel.com>

It adds a generic cpufreq driver for CPU0 frequency management based on
clk, regulator, OPP and device tree support.  It can support both
uniprocessor (UP) and those symmetric multiprocessor (SMP) systems which
share clock and voltage across all CPUs.
Signed-off-by: NShawn Guo <shawn.guo@linaro.org>
Acked-by: NSantosh Shilimkar <santosh.shilimkar@ti.com>
Tested-by: NAnilKumar Ch <anilkumar@ti.com>
Signed-off-by: NRafael J. Wysocki <rjw@sisk.pl>

These chips are now supported by acpi-cpufreq, so we can delete all the
code handling them.

Andre: Tighten the deprecation warning message. Trigger load of
acpi-cpufreq and let the load of the module finally fail.
This avoids the problem of users ending up without any cpufreq support
after the transition.
Signed-off-by: NMatthew Garrett <mjg@redhat.com>
Signed-off-by: NAndre Przywara <andre.przywara@amd.com>
Signed-off-by: NRafael J. Wysocki <rjw@sisk.pl>

This patch adds support cpufreq for EXYNOS5250 SoC. Basically,
the exynos-cpufreq.c is used commonly and exynos5250-cpufreq.c
is used for EXYNOS5250(two Cortex-A15 cores) SoC.
Signed-off-by: NJaecheol Lee <jc.lee@samsung.com>
Signed-off-by: NKukjin Kim <kgene.kim@samsung.com>
Signed-off-by: NDave Jones <davej@redhat.com>

This patch adds support cpufreq for EXYNOS4X12 SoCs. Basically,
the exynos-cpufreq.c is used commonly and exynos4x12-cpufreq.c
is used for EXYNOS4212(two Cortex-A9 cores) and EXYNOS4412(four
Cortex-A9 cores) SoCs.
Signed-off-by: NJaecheol Lee <jc.lee@samsung.com>
Signed-off-by: NKukjin Kim <kgene.kim@samsung.com>
Signed-off-by: NDave Jones <davej@redhat.com>

The S3C2416/S3C2450 SoCs support two sources for the armclk.

The first source is the so called armdiv which divides the msysclk down
to provide necessary cpu rates. In this mode the core voltage must be
always at 1.3V. The frequency from the armdiv is not allowed to be
lower than the hclk frequency.

In the second mode the armclk can be sourced directly from the hclk in
the so called "dynamic voltags scaling" (dvs) mode. Here the armdiv
isn't used at all. Also in this mode the core voltage may be lowered.
Existing hardware and tests with it suggest 1.0V as sufficient.

When changing the clock source to the armdiv from the hclk, the SoC
shows stability issues if the new frequency is higher than the current
hclk frequency. Hence the driver always forces the armdiv to the hclk
frequency before the source change and lets the cpufreq issue another
set_target call for higher frequencies.

To mark the hclk frequency as lower as the corresponding armdiv
frequency it is set 1MHz below the real frequency. This lets the cpufreq
framework change between 133MHz based on hclk and 133MHz based on armdiv
at will.
Signed-off-by: NHeiko Stuebner <heiko@sntech.de>
Tested-by: NAndrey Gusakov <dron0gus@gmail.com>
Signed-off-by: NDave Jones <davej@redhat.com>

The OMAP driver depends on CPUfreq table support for creating a table
of frequencies from the OPP layer.  Ensure that it's build to avoid
link-time errors.
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>
[khilman@ti.com: make user-selectable, but default y]
Signed-off-by: NKevin Hilman <khilman@ti.com>

To support various EXYNOS series SoCs commonly,
added exynos common structure.
exynos-cpufreq.c => EXYNOS series common cpufreq driver
exynos4210-cpufreq.c => EXYNOS4210 support cpufreq driver
Signed-off-by: NJaecheol Lee <jc.lee@samsung.com>
Signed-off-by: NKukjin Kim <kgene.kim@samsung.com>
Signed-off-by: NDave Jones <davej@redhat.com>

Move OMAP cpufreq driver from arch/arm/mach-omap2 into
drivers/cpufreq, along with a few cleanups:

- generalize support for better handling of different SoCs in the OMAP
- use OPP layer instead of OMAP clock internals for frequency table init
Signed-off-by: NSantosh Shilimkar <santosh.shilimkar@ti.com>
[khilman@ti.com: move to drivers]
Signed-off-by: NKevin Hilman <khilman@ti.com>

Add simple cpufreq driver for Maple-based boards (ppc970fx evaluation
kit and others). Driver is based on a cpufreq driver for 64-bit powermac
boxes with all pmac-dependant features removed and simple cleanup
applied.
Signed-off-by: NDmitry Eremin-Solenikov <dbaryshkov@gmail.com>
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>

Cc: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: NKukjin Kim <kgene.kim@samsung.com>
Signed-off-by: NDave Jones <davej@redhat.com>

According to discussion of the ARM arch subsystem migration,
ARM cpufreq drivers move to drivers/cpufreq. So this patch
adds Kconfig.arm for ARM like x86 and adds Samsung S5PV210
and EXYNOS4210 cpufreq driver compile in there.
As a note, otherw will be moved.

Cc: Dave Jones <davej@redhat.com>
Signed-off-by: NKukjin Kim <kgene.kim@samsung.com>
Signed-off-by: NDave Jones <davej@redhat.com>

This is a straight code motion patch, there are no changes to the driver
itself. The Kconfig is left untouched as the ARM CPUfreq Kconfig is all
in one big block in arm/Kconfig and should be moved en masse rather than
being done piecemeal.
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: NDave Jones <davej@redhat.com>

Concluding interface update and movement of the driver by making
the DB8500 cpufreq driver compile in the cpufreq subsystem.

Cc: Arnd Bergmann <arnd@arndb.de>
Acked-by: NDave Jones <davej@redhat.com>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>

Signed-off-by: NDave Jones <davej@redhat.com>

A new cpufreq module, based on the ondemand one with my additional patches
just posted.  This one is more suitable for battery environments where its
probably more appealing to have the cpu freq gracefully increase and decrease
rather than flip between the min and max freq's.

N.B. Bruno Ducrot pointed out that the amd64's "do have unacceptable latency
between min and max freq transition, due to the step-by-step requirements
(200MHz IIRC)"; so AMD64 users would probably benefit from this too.
Signed-off-by: NAlexander Clouter <alex-kernel@digriz.org.uk>
Signed-off-by: NDave Jones <davej@redhat.com>

Initial git repository build. I'm not bothering with the full history,
even though we have it. We can create a separate "historical" git
archive of that later if we want to, and in the meantime it's about
3.2GB when imported into git - space that would just make the early
git days unnecessarily complicated, when we don't have a lot of good
infrastructure for it.

Let it rip!