zram could kunmap_atomic() a NULL pointer in a rare situation: a zram
page becomes a full-zeroed page after a partial write io.  The current
code doesn't handle this case and performs kunmap_atomic() on a NULL
pointer, which panics the kernel.

This patch fixes this issue.
Signed-off-by: NWeijie Yang <weijie.yang@samsung.com>
Cc: Sergey Senozhatsky <sergey.senozhatsky@gmail.com>
Cc: Dan Streetman <ddstreet@ieee.org>
Cc: Nitin Gupta <ngupta@vflare.org>
Cc: Weijie Yang <weijie.yang.kh@gmail.com>
Acked-by: NJerome Marchand <jmarchan@redhat.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Currently, we only match against local port number in order to reuse
socket. But if this new vxlan wants an IPv6 socket and a IPv4 one bound
to that port, vxlan will reuse an IPv4 socket as IPv6 and a panic will
follow. The following steps reproduce it:

   # ip link add vxlan6 type vxlan id 42 group 229.10.10.10 \
       srcport 5000 6000 dev eth0
   # ip link add vxlan7 type vxlan id 43 group ff0e::110 \
       srcport 5000 6000 dev eth0
   # ip link set vxlan6 up
   # ip link set vxlan7 up
   <panic>

[    4.187481] BUG: unable to handle kernel NULL pointer dereference at 0000000000000058
...
[    4.188076] Call Trace:
[    4.188085]  [<ffffffff81667c4a>] ? ipv6_sock_mc_join+0x3a/0x630
[    4.188098]  [<ffffffffa05a6ad6>] vxlan_igmp_join+0x66/0xd0 [vxlan]
[    4.188113]  [<ffffffff810a3430>] process_one_work+0x220/0x710
[    4.188125]  [<ffffffff810a33c4>] ? process_one_work+0x1b4/0x710
[    4.188138]  [<ffffffff810a3a3b>] worker_thread+0x11b/0x3a0
[    4.188149]  [<ffffffff810a3920>] ? process_one_work+0x710/0x710

So address family must also match in order to reuse a socket.
Reported-by: NJean-Tsung Hsiao <jhsiao@redhat.com>
Signed-off-by: NMarcelo Ricardo Leitner <mleitner@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

With commit be9dad1f ("net: phy: suspend phydev when going
to HALTED"), the PHY device will be put in a low-power mode using
BMCR_PDOWN if the the interface is set down. The smsc911x driver does
a software_reset opening the device driver (ndo_open). In such case,
the PHY must be powered-up before access to any register and before
calling the software_reset function. Otherwise, as the PHY is powered
down the software reset fails and the interface can not be enabled
again.

This patch fixes this scenario that is easy to reproduce setting down
the network interface and setting up again.

    $ ifconfig eth0 down
    $ ifconfig eth0 up
    ifconfig: SIOCSIFFLAGS: Input/output error
Signed-off-by: NEnric Balletbo i Serra <eballetbo@iseebcn.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Increased delay in the smsc911x_phy_disable_energy_detect (from 1ms to 2ms).
Dropped delays in the smsc911x_phy_enable_energy_detect (100ms and 1ms).

The patch affect SMSC LAN generation 4 chips with integrated PHY (LAN9221).

I saw problems with soft reset due to wrong udelay timings.
After I fixed udelay, I measured the time needed to bring integrated PHY
from power-down to operational mode (the time beetween clearing EDPWRDOWN
bit and soft reset complete event). I got 1ms (measured using ktime_get).
The value is equal to the current value (1ms) used in the
smsc911x_phy_disable_energy_detect. It is near the upper bound and in order
to avoid rare soft reset faults it is doubled (2ms).

I don't know official timing for bringing up integrated PHY as specs doesn't
clarify this (or may be I didn't found).

It looks safe to drop delays before and after setting EDPWRDOWN bit
(enable PHY power-down mode). I didn't saw any regressions with the patch.

The patch was reviewed by Steve Glendinning and Microchip Team.
Signed-off-by: NAlexander Kochetkov <al.kochet@gmail.com>
Acked-by: NSteve Glendinning <steve.glendinning@shawell.net>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The patch affect SMSC LAN generation 4 chips with integrated PHY (LAN9221).

It is possible that PHY could enter power-down mode (ENERGYON clear),
between ENERGYON bit check in smsc911x_phy_disable_energy_detect and SRST
bit set in smsc911x_soft_reset. This could happen, for example, if someone
disconnect ethernet cable between the checks. The PHY in a power-down mode
would prevent the MAC portion of chip to be software reseted.

Initially found by code review, confirmed later using test case.

This is low probability issue, and in order to reproduce it you have to
run the script:

while true; do
	ifconfig eth0 down
	ifconfig eth0 up || break
done

While the script is running you have to plug/unplug ethernet cable many
times (using gpio controlled ethernet switch, for example) until get:

[ 4516.477783] ADDRCONF(NETDEV_UP): eth0: link is not ready
[ 4516.512207] smsc911x smsc911x.0: eth0: SMSC911x/921x identified at 0xce006000, IRQ: 336
[ 4516.524658] ADDRCONF(NETDEV_UP): eth0: link is not ready
[ 4516.559082] smsc911x smsc911x.0: eth0: SMSC911x/921x identified at 0xce006000, IRQ: 336
[ 4516.571990] ADDRCONF(NETDEV_UP): eth0: link is not ready
ifconfig: SIOCSIFFLAGS: Input/output error

The patch was reviewed by Steve Glendinning and Microchip Team.
Signed-off-by: NAlexander Kochetkov <al.kochet@gmail.com>
Acked-by: NSteve Glendinning <steve.glendinning@shawell.net>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Commit f5866db6 (virtio_console: enable VQs early) tried to make
sure that DRIVER_OK was set when virtio_console started using its
virtqueues. Doing this in add_port(), however, means that we try
to set DRIVER_OK again when when a port is dynamically added after
the probe function is done.

Let's move virtio_device_ready() to the probe function just before
trying to use the virtqueues instead. This is fine as nothing can
fail inbetween.
Reported-by: NThomas Graf <tgraf@suug.ch>
Reviewed-by: NMichael S. Tsirkin <mst@redhat.com>
Signed-off-by: NCornelia Huck <cornelia.huck@de.ibm.com>
Signed-off-by: NMichael S. Tsirkin <mst@redhat.com>

Commit ae5c6c6d "ptp: Classify ptp over ip over vlan packets" changed the
code in two drivers that matches time stamps with PTP frames, with the goal
of allowing VLAN tagged PTP packets to receive hardware time stamps.

However, that commit failed to account for the VLAN header when parsing
IPv4 packets. This patch fixes those two drivers to correctly match VLAN
tagged IPv4/UDP PTP messages with their time stamps.

This patch should also be applied to v3.17.
Signed-off-by: NRichard Cochran <richardcochran@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

* In LLD_MANAGED mode, traffic classes were being returned in reverse order to
  lldp agent.
* Priotype of strict is no longer the default returned.
* Change behaviour of getdcbx() based on discussions on lldp-devel

These were missed as there was no working fetch interface for open-lldp when
running in LLD_MANAGED mode till now.

Fixes: 76bcb31e ("cxgb4 : Add DCBx support codebase and dcbnl_ops")
Signed-off-by: NAnish Bhatt <anish@chelsio.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

In case an interface has been brought down before entering S3, and then
brought up out of S3, all the initialization done during
bcmgenet_probe() by bcmgenet_mii_init() calling bcmgenet_mii_config() is
just lost since register contents are restored to their reset values.

Re-apply this configuration anytime we call bcmgenet_open() to make sure
our port multiplexer is properly configured to match the PHY interface.

Since we are now calling bcmgenet_mii_config() everytime bcmgenet_open()
is called, make sure we only print the message during initialization
time not to pollute the console.

Fixes: b6e978e5 ("net: bcmgenet: add suspend/resume callbacks")
Fixes: 1c1008c7 ("net: bcmgenet: add main driver file")
Signed-off-by: NFlorian Fainelli <f.fainelli@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

phy_disconnect() is the only way to guarantee that we are not going to
schedule more work on the PHY state machine workqueue for that
particular PHY device.

This fixes an issue where a network interface was suspended prior to a
system suspend/resume cycle and would then be resumed as part of
mdio_bus_resume(), since the GENET interface clocks would have been
disabled, this basically resulted in bus errors to appear since we are
invoking the GENET driver adjust_link() callback.

Fixes: b6e978e5 ("net: bcmgenet: add suspend/resume callbacks")
Signed-off-by: NFlorian Fainelli <f.fainelli@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch removes the dependency of the VENDOR entry and fixes
the QCA7000 one.
Signed-off-by: NStefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Status variable is never initialized, can carry an arbitrary value
on the stack and thus may let the function fail.

Fixes: e90dd264 ("ixgbe: Make return values more direct")
Signed-off-by: NDaniel Borkmann <dborkman@redhat.com>
Acked-by: NEmil Tantilov <emil.s.tantilov@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Based on the reference clock, which could be 25MHz or 40MHz,
AR_RTC_DERIVED_CLK is programmed differently for AR9340 and AR9550.
But, when a chip reset is done, processing the initvals
sets the register back to the default value.

Fix this by moving the code in ath9k_hw_init_pll() to
ar9003_hw_override_ini(). Also, do this override for AR9531.

Cc: stable@vger.kernel.org
Signed-off-by: NMiaoqing Pan <miaoqing@qca.qualcomm.com>
Signed-off-by: NSujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

When advertised capabilities are changed with mii-tool, such as:
mii-tool -A 10baseT
the existing handler has two errors.

- An actual PHY register value is provided by mii-tool, and this
  must be mapped to internal state with mii_adv_to_ethtool_adv_t().
- The PHY state machine needs to be told that autonegotiation has
  again been performed.  If not, the MAC will not be notified of
  the new link speed and duplex, resulting in a possible config
  mismatch.
Signed-off-by: NBrian Hill <Brian@houston-radar.com>
Acked-by: NFlorian Fainelli <f.fainelli@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The function chandef_to_chanspec() failed when converting a
chandef with bandwidth set to NL80211_CHAN_WIDTH_20_NOHT. This
was reported by user running the device in AP mode.

------------[ cut here ]------------
WARNING: CPU: 0 PID: 304 at
	drivers/net/wireless/brcm80211/brcmfmac/wl_cfg80211.c:381
		chandef_to_chanspec.isra.11+0x158/0x184()

Modules linked in:

CPU: 0 PID: 304 Comm: hostapd Not tainted 3.16.0-rc7-abb+g64aa90f2 #8

[<c0014bb4>] (unwind_backtrace) from [<c0012314>] (show_stack+0x10/0x14)
[<c0012314>] (show_stack) from [<c001d3f8>] (warn_slowpath_common+0x6c/0x8c)
[<c001d3f8>] (warn_slowpath_common) from [<c001d4b4>] (warn_slowpath_null+0x1c/0x24)
[<c001d4b4>] (warn_slowpath_null) from [<c03449a4>] (chandef_to_chanspec.isra.11+0x158/0x184)
[<c03449a4>] (chandef_to_chanspec.isra.11) from [<c0348e00>] (brcmf_cfg80211_start_ap+0x1e4/0x614)
[<c0348e00>] (brcmf_cfg80211_start_ap) from [<c04d1468>] (nl80211_start_ap+0x288/0x414)
[<c04d1468>] (nl80211_start_ap) from [<c043d144>] (genl_rcv_msg+0x21c/0x38c)
[<c043d144>] (genl_rcv_msg) from [<c043c740>] (netlink_rcv_skb+0xac/0xc0)
[<c043c740>] (netlink_rcv_skb) from [<c043cf14>] (genl_rcv+0x20/0x34)
[<c043cf14>] (genl_rcv) from [<c043c0a0>] (netlink_unicast+0x150/0x20c)
[<c043c0a0>] (netlink_unicast) from [<c043c4b8>] (netlink_sendmsg+0x2b8/0x398)
[<c043c4b8>] (netlink_sendmsg) from [<c04066a4>] (sock_sendmsg+0x84/0xa8)
[<c04066a4>] (sock_sendmsg) from [<c0407c5c>] (___sys_sendmsg.part.29+0x268/0x278)
[<c0407c5c>] (___sys_sendmsg.part.29) from [<c0408bdc>] (__sys_sendmsg+0x4c/0x7c)
[<c0408bdc>] (__sys_sendmsg) from [<c000ec60>] (ret_fast_syscall+0x0/0x44)
---[ end trace 965ee2158c9905a2 ]---

Cc: stable@vger.kernel.org # v3.17
Reported-by: NPontus Fuchs <pontusf@broadcom.com>
Reviewed-by: NHante Meuleman <meuleman@broadcom.com>
Reviewed-by: NDaniel (Deognyoun) Kim <dekim@broadcom.com>
Reviewed-by: NFranky (Zhenhui) Lin <frankyl@broadcom.com>
Reviewed-by: NPieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: NArend van Spriel <arend@broadcom.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

RT2800 and newer hardware require padding between header and payload if
header length is not multiple of 4.

For historical reasons we also align payload to to 4 bytes boundary, but
such alignment is not needed on modern H/W.

Patch fixes skb_under_panic problems reported from time to time:

https://bugzilla.kernel.org/show_bug.cgi?id=84911
https://bugzilla.kernel.org/show_bug.cgi?id=72471
http://marc.info/?l=linux-wireless&m=139108549530402&w=2
https://bugs.launchpad.net/ubuntu/+source/linux/+bug/1087591

Panic happened because we eat 4 bytes of skb headroom on each
(re)transmission when sending frame without the payload and the header
length not being multiple of 4 (i.e. QoS header has 26 bytes). On such
case because paylad_aling=2 is bigger than header_align=0 we increase
header_align by 4 bytes. To prevent that we could change the check to:

	if (payload_length && payload_align > header_align)
		header_align += 4;

but not aligning payload at all is more effective and alignment is not
really needed by H/W (that has been tested on OpenWrt project for few
years now).
Reported-and-tested-by: NAntti S. Lankila <alankila@bel.fi>
Debugged-by: NAntti S. Lankila <alankila@bel.fi>
Reported-by: NHenrik Asp <solenskiner@gmail.com>
Originally-From: Helmut Schaa <helmut.schaa@googlemail.com>
Cc: stable@vger.kernel.org
Signed-off-by: NStanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

In ppp_ioctl(), bpf_prog_create() is called inside ppp_lock, which
eventually calls vmalloc() and hits BUG_ON() in vmalloc.c.  This patch
works around the problem by moving the allocation outside the lock.

The bug was revealed by the recent change in net/core/filter.c, as it
allocates via vmalloc() instead of kmalloc() now.
Reported-and-tested-by: NStefan Seyfried <stefan.seyfried@googlemail.com>
Signed-off-by: NTakashi Iwai <tiwai@suse.de>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

F3 device ID is wrongly included in fam15h_power_id_table
for F16h M30h. It should be F4 device ID. Fix this.
Signed-off-by: NAravind Gopalakrishnan <aravind.gopalakrishnan@amd.com>
Signed-off-by: NGuenter Roeck <linux@roeck-us.net>

The state of a PWM output is not clearly defined after resume. Some PWM
drivers do not restore the duty cycle upon resume, thus it is necessary to
manually restore the correct value.
Signed-off-by: NKamil Debski <k.debski@samsung.com>
Signed-off-by: NGuenter Roeck <linux@roeck-us.net>

Because we build kernels with drivers built in for many platforms, it's
normal for the ibmpowernv driver to be loaded on systems that don't have
the appropriate hardware.

Currently the driver spams the log with:

  ibmpowernv ibmpowernv.0: Opal node 'sensors' not found
  ibmpowernv: Platfrom driver probe failed

But there is no error, this machine is not a powernv and doesn't have
the hardware. So change the sensors message to dev_dbg(), and only print
an error about the probe failing if it's not ENODEV.

Also fix the spelling of "Platfrom" and print the actual error value.
Signed-off-by: NMichael Ellerman <mpe@ellerman.id.au>
Reviewed-by: NJean Delvare <jdelvare@suse.de>
Signed-off-by: NGuenter Roeck <linux@roeck-us.net>

Currenly we only support Large-Send and TX checksum offloads for
encapsulated traffic of type VXLAN. We must make sure to advertize
these offloads up to the stack only when VXLAN tunnel is set.

Failing to do so, would mislead the the networking stack to assume
that the driver can offload the internal TX checksum for GRE packets
and other buggy schemes.
Reported-by: NFlorian Westphal <fw@strlen.de>
Signed-off-by: NOr Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The length counting previously done had an error in it, causing
the length down the data dumping function to be shorter than it
should be, causing the end of the data to get truncated off and
lost.

Cc: <stable@vger.kernel.org> [3.17+]
Fixes: 67c65f2c ("iwlwifi: dump periphery registers to fw-error-dump")
Signed-off-by: NLiad Kaufman <liad.kaufman@intel.com>
Reviewed-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

This code existed but not for all the different FW APIs
we support.
Fix this.
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

The walk code was using a 'ro_spine' to hold it's locked btree nodes.
But this data structure is designed for the rolling lock scheme, and
as such automatically unlocks blocks that are two steps up the call
chain.  This is not suitable for the simple recursive walk algorithm,
which retraces its steps.

This code is only used by the persistent array code, which in turn is
only used by dm-cache.  In order to trigger it you need to have a
mapping tree that is more than 2 levels deep; which equates to 8-16
million cache blocks.  For instance a 4T ssd with a very small block
size of 32k only just triggers this bug.

The fix just places the locked blocks on the stack, and stops using
the ro_spine altogether.
Signed-off-by: NJoe Thornber <ejt@redhat.com>
Signed-off-by: NMike Snitzer <snitzer@redhat.com>
Cc: stable@vger.kernel.org

Unlike CEE, IEEE has a bespoke app delete call and does not rely on priority
for app deletion

Fixes : 2376c879 ('cxgb4 : Improve handling of DCB negotiation or loss
 thereof')
Signed-off-by: NAnish Bhatt <anish@chelsio.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When doing GRO processing for UDP tunnels, we never add
SKB_GSO_UDP_TUNNEL to gso_type - only the type of the inner protocol
is added (such as SKB_GSO_TCPV4). The result is that if the packet is
later resegmented we will do GSO but not treat it as a tunnel. This
results in UDP fragmentation of the outer header instead of (i.e.) TCP
segmentation of the inner header as was originally on the wire.
Signed-off-by: NJesse Gross <jesse@nicira.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Free List Starvation Threshold needs to be larger than the SGE's Egress
Congestion Threshold or we'll end up in a mutual stall where the driver waits
for Ingress Packets to drive replacing Free List Pointers and the SGE waits for
Free List Pointers before pushing Ingress Packets to the host.

Based on original work by Casey Leedom <leedom@chelsio.com>
Signed-off-by: NHariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

T5 introduces the ability to have separate Packing and Padding Boundaries
for SGE DMA transfers from the chip to Host Memory. This change set takes
advantage of that to set up a smaller Padding Boundary to conserve PCI Link
and Memory Bandwidth with T5.
Signed-off-by: NHariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Move fl_starv_thres into adapter->sge data structure since it
_could_ be different from adapter to adapter.  Also move other per-adapter
SGE values which had been treated as driver globals into adapter->sge.

Based on original work by Casey Leedom <leedom@chelsio.com>
Signed-off-by: NHariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

phy_read and phy_write are not set for every phy any more sine this:
commit d342b95d
Author: Rafał Miłecki <zajec5@gmail.com>
Date:   Thu Jul 31 21:59:43 2014 +0200

    b43: don't duplicate common PHY read/write ops

b43_phy_copy() accesses phy_read and phy_write directly and will fail
with some phys. This patch fixes the regression by using the
b43_phy_read() and b43_phy_write() functions which should be used for
read and write access.

This should fix this bug report:
https://bugzilla.kernel.org/show_bug.cgi?id=87731Reported-by: NVolker Kempter <v.kempter@pe.tu-clausthal.de>
Tested-by: NVolker Kempter <v.kempter@pe.tu-clausthal.de>
Signed-off-by: NHauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Changes in the vendor driver were added to rtlwifi, but some updates
to rtl8192se were missed, and the driver could neither scan nor connect.
There are other changes that will enhance performance, but this minimal
set fix the basic functionality.
Signed-off-by: NLarry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

There are typos in the handling of the descriptor pointers where the wrong
descriptor is referenced. There is also an error in which the pointer is
incremented twice.
Signed-off-by: NLarry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Device RTL8192EE uses a new form of trx flow. This fix sets up the descriptors
correctly.
Signed-off-by: NLarry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Commit e7cd1d1e ("mfd: twl4030-power: Add generic reset
configuration") enabled configuring the PM features for twl4030.

This caused poweroff command to fail on devices that have the
BCI charger on twl4030 wired, or have power wired for VBUS.
Instead of powering off, the device reboots. This is because
voltage is detected on charger or VBUS with the default bits
enabled for the power transition registers.

To fix the issue, let's just clear VBUS and CHG bits as we want
poweroff command to keep the system powered off.

Fixes: e7cd1d1e ("mfd: twl4030-power: Add generic reset configuration")
Cc: stable@vger.kernel.org # v3.16+
Reported-by: NRussell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: NTony Lindgren <tony@atomide.com>
Signed-off-by: NLee Jones <lee.jones@linaro.org>

All interrupts coming from MUIC were ignored because interrupt source
register was masked.

The Maxim 77693 has a "interrupt source" - a separate register and interrupts
which give information about PMIC block triggering the individual
interrupt (charger, topsys, MUIC, flash LED).

By default bootloader could initialize this register to "mask all"
value. In such case (observed on Trats2 board) MUIC interrupts won't be
generated regardless of their mask status. Regmap irq chip was unmasking
individual MUIC interrupts but the source was masked

Before introducing regmap irq chip this interrupt source was unmasked,
read and acked. Reading and acking is not necessary but unmasking is.

Fixes: 342d669c ("mfd: max77693: Handle IRQs using regmap")

Cc: <stable@vger.kernel.org>
Signed-off-by: NKrzysztof Kozlowski <k.kozlowski@samsung.com>
Reviewed-by: NChanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: NLee Jones <lee.jones@linaro.org>

Interrupts coming from Maxim77693 MUIC block (MicroUSB Interface
Controller) were not handled at all because wrong regmap was used for
MUIC's regmap_irq_chip.

The MUIC component of Maxim 77693 uses different I2C address thus second
regmap is created and used by max77693 extcon driver. The registers for
MUIC interrupts are also in that block and should be handled by that
second regmap.

However the regmap irq chip for MUIC was configured with default regmap
which could not read MUIC registers.

Fixes: 342d669c ("mfd: max77693: Handle IRQs using regmap")

Cc: <stable@vger.kernel.org>
Signed-off-by: NKrzysztof Kozlowski <k.kozlowski@samsung.com>
Reviewed-by: NChanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: NLee Jones <lee.jones@linaro.org>

Allow more than one viperboard to be connected by registering with
PLATFORM_DEVID_AUTO instead of PLATFORM_DEVID_NONE.

The subdevices are currently registered with PLATFORM_DEVID_NONE, which
will cause a name collision on the platform bus when a second viperboard
is plugged in:

viperboard 1-2.4:1.0: version 0.00 found at bus 001 address 004
------------[ cut here ]------------
WARNING: CPU: 0 PID: 181 at /home/johan/work/omicron/src/linux/fs/sysfs/dir.c:31 sysfs_warn_dup+0x74/0x84()
sysfs: cannot create duplicate filename '/bus/platform/devices/viperboard-gpio'
Modules linked in: i2c_viperboard viperboard netconsole [last unloaded: viperboard]
CPU: 0 PID: 181 Comm: bash Tainted: G        W      3.17.0-rc6 #1
[<c0016bf4>] (unwind_backtrace) from [<c0013860>] (show_stack+0x20/0x24)
[<c0013860>] (show_stack) from [<c04305f8>] (dump_stack+0x24/0x28)
[<c04305f8>] (dump_stack) from [<c0040fb4>] (warn_slowpath_common+0x80/0x98)
[<c0040fb4>] (warn_slowpath_common) from [<c004100c>] (warn_slowpath_fmt+0x40/0x48)
[<c004100c>] (warn_slowpath_fmt) from [<c016f1bc>] (sysfs_warn_dup+0x74/0x84)
[<c016f1bc>] (sysfs_warn_dup) from [<c016f548>] (sysfs_do_create_link_sd.isra.2+0xcc/0xd0)
[<c016f548>] (sysfs_do_create_link_sd.isra.2) from [<c016f588>] (sysfs_create_link+0x3c/0x48)
[<c016f588>] (sysfs_create_link) from [<c02867ec>] (bus_add_device+0x12c/0x1e0)
[<c02867ec>] (bus_add_device) from [<c0284820>] (device_add+0x410/0x584)
[<c0284820>] (device_add) from [<c0289440>] (platform_device_add+0xd8/0x26c)
[<c0289440>] (platform_device_add) from [<c02a5ae4>] (mfd_add_device+0x240/0x344)
[<c02a5ae4>] (mfd_add_device) from [<c02a5ce0>] (mfd_add_devices+0xb8/0x110)
[<c02a5ce0>] (mfd_add_devices) from [<bf00d1c8>] (vprbrd_probe+0x160/0x1b0 [viperboard])
[<bf00d1c8>] (vprbrd_probe [viperboard]) from [<c030c000>] (usb_probe_interface+0x1bc/0x2a8)
[<c030c000>] (usb_probe_interface) from [<c028768c>] (driver_probe_device+0x14c/0x3ac)
[<c028768c>] (driver_probe_device) from [<c02879e4>] (__driver_attach+0xa4/0xa8)
[<c02879e4>] (__driver_attach) from [<c0285698>] (bus_for_each_dev+0x70/0xa4)
[<c0285698>] (bus_for_each_dev) from [<c0287030>] (driver_attach+0x2c/0x30)
[<c0287030>] (driver_attach) from [<c030a288>] (usb_store_new_id+0x170/0x1ac)
[<c030a288>] (usb_store_new_id) from [<c030a2f8>] (new_id_store+0x34/0x3c)
[<c030a2f8>] (new_id_store) from [<c02853ec>] (drv_attr_store+0x30/0x3c)
[<c02853ec>] (drv_attr_store) from [<c016eaa8>] (sysfs_kf_write+0x5c/0x60)
[<c016eaa8>] (sysfs_kf_write) from [<c016dc68>] (kernfs_fop_write+0xd4/0x194)
[<c016dc68>] (kernfs_fop_write) from [<c010fe40>] (vfs_write+0xb4/0x1c0)
[<c010fe40>] (vfs_write) from [<c01104a8>] (SyS_write+0x4c/0xa0)
[<c01104a8>] (SyS_write) from [<c000f900>] (ret_fast_syscall+0x0/0x48)
---[ end trace 98e8603c22d65817 ]---
viperboard 1-2.4:1.0: Failed to add mfd devices to core.
viperboard: probe of 1-2.4:1.0 failed with error -17
Signed-off-by: NJohan Hovold <johan@kernel.org>
Signed-off-by: NLee Jones <lee.jones@linaro.org>

rtsx_pci_power_off() is called only from rtsx_pci_suspend(), which isn't
built when PM is disabled.
Signed-off-by: NThierry Reding <treding@nvidia.com>
Signed-off-by: NLee Jones <lee.jones@linaro.org>

The least significat byte of the GPIO value read register
on the STMPE24xx series is on addres 0xA4 not 0xA5. Correct
against datasheet and tested on the STMPE2401 hardware.
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>
Signed-off-by: NLee Jones <lee.jones@linaro.org>

imx_get_temp might be called before the sensor clock is prepared
thus resulting in a timeout of the first attempt to read temp:
thermal thermal_zone0: failed to read out thermal zone 0
Happened to me on a Utilite Standard with IMX6 Dual SoC.

Reason is that in imx_thermal_probe thermal_zone_device_register
is called before the sensor clock is prepared.
thermal_zone_device_register however calls
thermal_zone_device_update which eventually calls imx_get_temp.

Fix this by preparing the clock before calling
thermal_zone_device_register.
Signed-off-by: NHeiner Kallweit <heiner.kallweit@web.de>
Signed-off-by: NEduardo Valentin <edubezval@gmail.com>