tx params should be configured per interface.
add ieee80211_vif param to the conf_tx callback,
and change all the drivers that use this callback.

The following spatch was used:
@rule1@
struct ieee80211_ops ops;
identifier conf_tx_op;
@@
	ops.conf_tx = conf_tx_op;

@rule2@
identifier rule1.conf_tx_op;
identifier hw, queue, params;
@@
	conf_tx_op (
-		struct ieee80211_hw *hw,
+		struct ieee80211_hw *hw, struct ieee80211_vif *vif,
		u16 queue,
		const struct ieee80211_tx_queue_params *params) {...}
Signed-off-by: NEliad Peller <eliad@wizery.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

TSF can be kept per vif.
Add ieee80211_vif param to set/get/reset_tsf, and move
the debugfs entries to the per-vif directory.

Update all the drivers that implement these callbacks.
Signed-off-by: NEliad Peller <eliad@wizery.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The eeprom data is stored in little-endian order in the rt2x00 library.
As it was converted to cpu order in the read routines, the data need to
be converted to LE on a big-endian platform.
Signed-off-by: NLarry Finger <Larry.Finger@lwfinger.net>
Cc: Stable <stable@kernel.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Using gcc 4.4.5 on a Powerbook G4 with a PPC cpu, a complicated
if statement results in incorrect flow, whereas the equivalent switch
statement works correctly.
Signed-off-by: NLarry Finger <Larry.Finger@lwfinger.net>
Cc: stable <stable@kernel.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Use rt2800_config_wcid and rt2800_delete_wcid_attr to initialize the
WCID table instead of writing to the registers directly.
Signed-off-by: NHelmut Schaa <helmut.schaa@googlemail.com>
Signed-off-by: NIvo van Doorn <IvDoorn@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

If a STA is not known by the hw (i.e. has no WCID assigned) don't allow
aggregation since this might mess up tx status reports and we won't be
able to distinguish the reports of multiple WCID-less STAs.
Signed-off-by: NHelmut Schaa <helmut.schaa@googlemail.com>
Signed-off-by: NIvo van Doorn <IvDoorn@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This allows us to assign a WCID to each STA even for STAs without
crypto key.

To achieve this search for an unused WCID in the HW WCID table and
assign it to the according STA. When configuring a pairwise key for this
STA we don't need to write the MAC address and BSSIDX anymore but just
update the crypto related fields in the WCID_ATTR table.

This has two advantages:

1) Setting a new key for an already available STA (PTK rekeying) is
slightly less expensive and should improve performance in situations
where a lot of rekeying happens (e.g. a huge number of stations and/or
a small rekeying interval)

2) The TXWI now gets a WCID assigned for unencrypted frames which will
be reflected in the corresponding tx status report. This should make tx
status reports in unencrypted AP mode more reliable as we can
distinguish between multiple key-less STAs.
Signed-off-by: NHelmut Schaa <helmut.schaa@googlemail.com>
Signed-off-by: NIvo van Doorn <IvDoorn@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

When sending an unencrypted frame to a STA the driver might want to pass
a suitable WCID since we don't have a key index to allow tx status
reports to get properly assigned to the correct STA.
Signed-off-by: NHelmut Schaa <helmut.schaa@googlemail.com>
Signed-off-by: NIvo van Doorn <IvDoorn@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

When a WCID was already assigned to a STA the key configuration
functions need to use the same WCID for configuring the keys. Hence, add
the WCID to the crypo configuration structure.
Signed-off-by: NHelmut Schaa <helmut.schaa@googlemail.com>
Signed-off-by: NIvo van Doorn <IvDoorn@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This implements a basic sta_add and sta_remove callback. Introduce a new
structure rt2x00_sta and ask mac80211 to allocate it as private part of
its ieee80211_sta. rt2x00_sta only contains the WCID for now.

The sta_add callback allows the driver to assign a WCID to a station
that is currently being added. The same wcid is also passed to the
sta_remove callback one mac80211 removes this STA.
Signed-off-by: NHelmut Schaa <helmut.schaa@googlemail.com>
Signed-off-by: NIvo van Doorn <IvDoorn@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This will be used by a later patch. No functional changes.
Signed-off-by: NHelmut Schaa <helmut.schaa@googlemail.com>
Signed-off-by: NIvo van Doorn <IvDoorn@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Reading the TX desciptor words from coherent memory is always uncached
and potentially slow. Hence, don't read the TX descriptor prior to
writing it since we update all fields anyway.
Signed-off-by: NHelmut Schaa <helmut.schaa@googlemail.com>
Acked-by: NGertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: NIvo van Doorn <IvDoorn@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: NHelmut Schaa <helmut.schaa@googlemail.com>
Acked-by: NGertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: NIvo van Doorn <IvDoorn@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

rt2800 devices are not capable of configuring arbitrary LED on/off
periods. The LED_CFG register fields ON_PERIOD and OFF_PERIOD are only
used by the hw when the LED mode is set to "blink upon TX".

Hence, remove the blink callback. This will result in software emulation
for LED blinking.
Signed-off-by: NHelmut Schaa <helmut.schaa@googlemail.com>
Acked-by: NGertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: NIvo van Doorn <IvDoorn@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: NHelmut Schaa <helmut.schaa@googlemail.com>
Acked-by: NGertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: NIvo van Doorn <IvDoorn@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

We can save an indirect function call + some instructions for fetching
the actual function pointer by passing the driver specific txwi pointer
directly from rt2800pci/rt2800usb to rt2800lib instead of using the
rt2800_drv_get_txwi callback.
Signed-off-by: NHelmut Schaa <helmut.schaa@googlemail.com>
Acked-by: NGertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: NIvo van Doorn <IvDoorn@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: Nzero.lin <zero.lin@ralinktech.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

When hibernating ->resume may not be called by usb core, but disconnect
and probe instead, so we do not increase the counter after decreasing
it in ->supend. As a result we free memory early, and get crash when
unplugging usb dongle.

BUG: unable to handle kernel paging request at 6b6b6b9f
IP: [<c06909b0>] driver_sysfs_remove+0x10/0x30
*pdpt = 0000000034f21001 *pde = 0000000000000000
Pid: 20, comm: khubd Not tainted 3.1.0-rc1-wl+ #20 LENOVO 6369CTO/6369CTO
EIP: 0060:[<c06909b0>] EFLAGS: 00010202 CPU: 1
EIP is at driver_sysfs_remove+0x10/0x30
EAX: 6b6b6b6b EBX: f52bba34 ECX: 00000000 EDX: 6b6b6b6b
ESI: 6b6b6b6b EDI: c0a0ea20 EBP: f61c9e68 ESP: f61c9e64
 DS: 007b ES: 007b FS: 00d8 GS: 00e0 SS: 0068
Process khubd (pid: 20, ti=f61c8000 task=f6138270 task.ti=f61c8000)
Call Trace:
 [<c06909ef>] __device_release_driver+0x1f/0xa0
 [<c0690b20>] device_release_driver+0x20/0x40
 [<c068fd64>] bus_remove_device+0x84/0xe0
 [<c068e12a>] ? device_remove_attrs+0x2a/0x80
 [<c068e267>] device_del+0xe7/0x170
 [<c06d93d4>] usb_disconnect+0xd4/0x180
 [<c06d9d61>] hub_thread+0x691/0x1600
 [<c0473260>] ? wake_up_bit+0x30/0x30
 [<c0442a39>] ? complete+0x49/0x60
 [<c06d96d0>] ? hub_disconnect+0xd0/0xd0
 [<c06d96d0>] ? hub_disconnect+0xd0/0xd0
 [<c0472eb4>] kthread+0x74/0x80
 [<c0472e40>] ? kthread_worker_fn+0x150/0x150
 [<c0809b3e>] kernel_thread_helper+0x6/0x10

Cc: stable@kernel.org
Signed-off-by: NStanislaw Gruszka <sgruszka@redhat.com>
Acked-by: NIvo van Doorn <IvDoorn@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Patch should fix this oops:

BUG: unable to handle kernel NULL pointer dereference at 000000a0
IP: [<f81b30c9>] rt2800usb_get_txwi+0x19/0x70 [rt2800usb]
*pdpt = 0000000000000000 *pde = f000ff53f000ff53
Oops: 0000 [#1] SMP
Pid: 198, comm: kworker/u:3 Tainted: G        W   3.0.0-wl+ #9 LENOVO 6369CTO/6369CTO
EIP: 0060:[<f81b30c9>] EFLAGS: 00010283 CPU: 1
EIP is at rt2800usb_get_txwi+0x19/0x70 [rt2800usb]
EAX: 00000000 EBX: f465e140 ECX: f4494960 EDX: ef24c5f8
ESI: 810f21f5 EDI: f1da9960 EBP: f4581e80 ESP: f4581e70
 DS: 007b ES: 007b FS: 00d8 GS: 00e0 SS: 0068
Process kworker/u:3 (pid: 198, ti=f4580000 task=f4494960 task.ti=f4580000)
Call Trace:
 [<f804790f>] rt2800_txdone_entry+0x2f/0xf0 [rt2800lib]
 [<c045110d>] ? warn_slowpath_common+0x7d/0xa0
 [<f81b3a38>] ? rt2800usb_work_txdone+0x288/0x360 [rt2800usb]
 [<f81b3a38>] ? rt2800usb_work_txdone+0x288/0x360 [rt2800usb]
 [<f81b3a13>] rt2800usb_work_txdone+0x263/0x360 [rt2800usb]
 [<c046a8d6>] process_one_work+0x186/0x440
 [<c046a85a>] ? process_one_work+0x10a/0x440
 [<f81b37b0>] ? rt2800usb_probe_hw+0x120/0x120 [rt2800usb]
 [<c046c283>] worker_thread+0x133/0x310
 [<c04885db>] ? trace_hardirqs_on+0xb/0x10
 [<c046c150>] ? manage_workers+0x1e0/0x1e0
 [<c047054c>] kthread+0x7c/0x90
 [<c04704d0>] ? __init_kthread_worker+0x60/0x60
 [<c0826b42>] kernel_thread_helper+0x6/0x1

Oops might happen because we check rt2x00queue_empty(queue) twice,
but this condition can change and we can process entry in
rt2800_txdone_entry(), which was already processed by
rt2800usb_txdone_entry_check() -> rt2x00lib_txdone_noinfo() and
has nullify entry->skb .
Reported-by: NJustin Piszcz <jpiszcz@lucidpixels.com>
Cc: stable@kernel.org
Signed-off-by: NStanislaw Gruszka <sgruszka@redhat.com>
Acked-by: NIvo van Doorn <IvDoorn@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

In rt2800usb_work_txdone we check flags in order:

- ENTRY_OWNER_DEVICE_DATA
- ENTRY_DATA_STATUS_PENDING
- ENTRY_DATA_IO_FAILED

Modify flags in separate order in rt2x00usb_interrupt_txdone, to avoid
processing entries in _txdone with wrong flags or skip processing
ready entries.
Reported-by: NJustin Piszcz <jpiszcz@lucidpixels.com>
Cc: stable@kernel.org
Signed-off-by: NStanislaw Gruszka <sgruszka@redhat.com>
Acked-by: NIvo van Doorn <IvDoorn@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Patch should fix this oops:

BUG: unable to handle kernel NULL pointer dereference at 000000a0
IP: [<f8e06078>] rt2800usb_write_tx_desc+0x18/0xc0 [rt2800usb]
*pdpt = 000000002408c001 *pde = 0000000024079067 *pte = 0000000000000000
Oops: 0000 [#1] SMP
EIP: 0060:[<f8e06078>] EFLAGS: 00010282 CPU: 0
EIP is at rt2800usb_write_tx_desc+0x18/0xc0 [rt2800usb]
EAX: 00000035 EBX: ef2bef10 ECX: 00000000 EDX: d40958a0
ESI: ef1865f8 EDI: ef1865f8 EBP: d4095878 ESP: d409585c
 DS: 007b ES: 007b FS: 00d8 GS: 00e0 SS: 0068
Call Trace:
 [<f8da5e85>] rt2x00queue_write_tx_frame+0x155/0x300 [rt2x00lib]
 [<f8da424c>] rt2x00mac_tx+0x7c/0x370 [rt2x00lib]
 [<c04882b2>] ? mark_held_locks+0x62/0x90
 [<c081f645>] ? _raw_spin_unlock_irqrestore+0x35/0x60
 [<c04884ba>] ? trace_hardirqs_on_caller+0x5a/0x170
 [<c04885db>] ? trace_hardirqs_on+0xb/0x10
 [<f8d618ac>] __ieee80211_tx+0x5c/0x1e0 [mac80211]
 [<f8d631fc>] ieee80211_tx+0xbc/0xe0 [mac80211]
 [<f8d63163>] ? ieee80211_tx+0x23/0xe0 [mac80211]
 [<f8d632e1>] ieee80211_xmit+0xc1/0x200 [mac80211]
 [<f8d63220>] ? ieee80211_tx+0xe0/0xe0 [mac80211]
 [<c0487d45>] ? lock_release_holdtime+0x35/0x1b0
 [<f8d63986>] ? ieee80211_subif_start_xmit+0x446/0x5f0 [mac80211]
 [<f8d637dd>] ieee80211_subif_start_xmit+0x29d/0x5f0 [mac80211]
 [<f8d63924>] ? ieee80211_subif_start_xmit+0x3e4/0x5f0 [mac80211]
 [<c0760188>] ? sock_setsockopt+0x6a8/0x6f0
 [<c0760000>] ? sock_setsockopt+0x520/0x6f0
 [<c076daef>] dev_hard_start_xmit+0x2ef/0x650

Oops might happen because we perform parallel putting new entries in a
queue (rt2x00queue_write_tx_frame()) and removing entries after
finishing transmitting (rt2800usb_work_txdone()). There are cases when
_txdone may process an entry that was not fully send and nullify
entry->skb .

To fix check in _txdone if entry has flags that indicate pending
transmission and wait until flags get cleared.
Reported-by: NJustin Piszcz <jpiszcz@lucidpixels.com>
Cc: stable@kernel.org
Signed-off-by: NStanislaw Gruszka <sgruszka@redhat.com>
Acked-by: NIvo van Doorn <IvDoorn@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This patch add a device id for the wifi usb keys shiped by DVICO with
some of their tvix hardware.
Signed-off-by: NAnthony Bourguignon <contact+kernel@toniob.net>
Acked-by: NIvo van Doorn <IvDoorn@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Reported-by: NMaik-Holger Freudenberg <hhfeuer@gmx.de>
Signed-off-by: NIvo van Doorn <IvDoorn@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

When toggle_irq is called for PCI devices to disable device interrupts
it used tasklet_disable to wait for a possibly running tasklet to finish.
However, on SMP systems the tasklet might still be scheduled on another CPU.
Instead, use tasklet_kill to ensure that all scheduled tasklets are finished
before returning from toggle_irq.

Furthermore, it was possible that a tasklet reenabled its interrupt even
though interrupts have been disabled already. Fix this by checking the
DEVICE_STATE_ENABLED_RADIO flag before reenabling single interrupts
during tasklet processing.

While at it also enable/kill the TBTT and PRETBTT tasklets in the
toggle_irq callback and only use tasklet_kill in stop_queue to wait
for a currently scheduled beacon update before returning.
Signed-off-by: NHelmut Schaa <helmut.schaa@googlemail.com>
Signed-off-by: NIvo van Doorn <IvDoorn@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

We may call rt2x00queue_pause_queue(queue) with queue == NULL. Bug
was introduced by commit 62fe7784
"rt2x00: Fix stuck queue in tx failure case" .

Cc: stable@kernel.org # 3.0+
Signed-off-by: NStanislaw Gruszka <sgruszka@redhat.com>
Acked-by: NIvo van Doorn <IvDoorn@gmail.com>
Acked-by: NGertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This was introduced by commit
77b5621b (rt2x00: Don't use queue entry
as parameter when creating TX descriptor.)
Signed-off-by: NHelmut Schaa <helmut.schaa@googlemail.com>
Acked-by: NGertjan van Wingerde <gwingerde@gmail.com>
Acked-by: NIvo van Doorn <IvDoorn@gmail.com>
Reported-by: NRandy Dunlap <rdunlap@xenotime.net>
Acked-by: NRandy Dunlap <rdunlap@xenotime.net>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

We should clear skb->data not skb itself. Bug was introduced by:
commit 0b8004aa "rt2x00: Properly
reserve room for descriptors in skbs".

Cc: stable@kernel.org # 2.6.36+
Signed-off-by: NStanislaw Gruszka <sgruszka@redhat.com>
Acked-by: NGertjan van Wingerde <gwingerde@gmail.com>
Acked-by: NIvo van Doorn <IvDoorn@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Belkin's Connect N150 Wireless USB Adapter, model F7D1101 version 2, uses ID 0x945b.
Chipset info: rt: 3390, rf: 000b, rev: 3213.
I have just bought one, which started to work perfectly after the ID was added through this patch.
Signed-off-by: NEduardo Bacchi Kienetz <eduardo@kienetz.com>
Acked-by: NGertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: NIvo van Doorn <IvDoorn@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Implementing this callback function will cause mac80211 refrain from
going to powersave state when there are still untransmitted TX frames
in the queues.
This would exactly mimic the behaviour of the legacy vendor driver which
also doesn't go in powersave mode if there are still TX frames that are not
transmitted.
This should make powersaving and rt2x00 a better couple.
Signed-off-by: NGertjan van Wingerde <gwingerde@gmail.com>
Acked-by: NHelmut Schaa <helmut.schaa@googlemail.com>
Signed-off-by: NIvo van Doorn <IvDoorn@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Sitecom WLA4000 (USB ID 0x0df6:0x0060) is an RT3072 chipset.
Sitecom WLA5000 (USB ID 0x0df6:0x0062) is an RT3572 chipset.
Signed-off-by: NGertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: NIvo van Doorn <IvDoorn@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Reported-by: NWim Vander Schelden <wim@fixnum.org>
Signed-off-by: NGertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: NIvo van Doorn <IvDoorn@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Currently a lot of actions that can be done without the queue's tx lock
being held are done inside the locked area.
Move them out to have a leaner and meaner code that operates while the
tx lock is being held.
Signed-off-by: NGertjan van Wingerde <gwingerde@gmail.com>
Acked-by: NHelmut Schaa <helmut.schaa@googlemail.com>
Signed-off-by: NIvo van Doorn <IvDoorn@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The functions that create the tx descriptor structure do not operate on
a queue entry at all. Signal this fact in the code by not providing a
queue entry as a parameter, but the rt2x00 device structure and the skb
directly.

This patch is a preparation for reducing the time a queue is locked for
a tx operation.
Signed-off-by: NGertjan van Wingerde <gwingerde@gmail.com>
Acked-by: NHelmut Schaa <helmut.schaa@googlemail.com>
Signed-off-by: NIvo van Doorn <IvDoorn@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The rt2x00 driver gets frequent occurrences of the following error message
when operating under load:
phy0 -> rt2x00queue_write_tx_frame: Error - Arrived at non-free entry in the
non-full queue 2.

This is caused by simultaneous attempts from mac80211 to send a frame via
rt2x00, which are not properly serialized inside rt2x00queue_write_tx_frame,
causing the second frame to fail sending with the above mentioned error
message.

Fix this by introducing a per-queue spinlock to serialize the TX operations
on that queue.
Reported-by: NAndreas Hartmann <andihartmann@01019freenet.de>
Signed-off-by: NGertjan van Wingerde <gwingerde@gmail.com>
Acked-by: NHelmut Schaa <helmut.schaa@googlemail.com>
Signed-off-by: NIvo van Doorn <IvDoorn@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: NJoe Perches <joe@perches.com>
Acked-by: NIvo van Doorn <IvDoorn@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

When module is reloaded, device may fail to work, with messages:

[  342.211926] phy40 -> rt2x00lib_rxdone_read_signal: Warning - Frame received with unrecognized signal, mode=0x0000, signal=0x0059, type=2.
[  342.314254] phy40 -> rt2x00lib_rxdone_read_signal: Warning - Frame received with unrecognized signal, mode=0x0000, signal=0x004a, type=2.
[  342.416458] phy40 -> rt2x00lib_rxdone: Warning - Wrong frame size 3183 max 2432.
[  342.518605] phy40 -> rt2x00lib_rxdone_read_signal: Warning - Frame received with unrecognized signal, mode=0x0000, signal=0x00c9, type=2.
[  342.620836] phy40 -> rt2x00lib_rxdone_read_signal: Warning - Frame received with unrecognized signal, mode=0x0000, signal=0x00ae, type=1.
[  342.723201] phy40 -> rt2x00lib_rxdone: Warning - Wrong frame size 0 max 2432.
[  342.825399] phy40 -> rt2x00lib_rxdone: Warning - Wrong frame size 0 max 2432.
[  342.927624] phy40 -> rt2x00lib_rxdone: Warning - Wrong frame size 0 max 2432.
[  343.029804] phy40 -> rt2x00lib_rxdone: Warning - Wrong frame size 2491 max 2432.
[  343.132008] phy40 -> rt2x00lib_rxdone: Warning - Wrong frame size 2576 max 2432.
[  343.234326] phy40 -> rt2x00lib_rxdone_read_signal: Warning - Frame received with unrecognized signal, mode=0x0000, signal=0x004c, type=1.
[  343.438723] phy40 -> rt2x00lib_rxdone_read_signal: Warning - Frame received with unrecognized signal, mode=0x0000, signal=0x00e6, type=1.

Whereas replugging device make it functional. To solve that problem
force reset device during probe.

With patch messages are gone. Unfortunately device may sometimes
still does not operate correctly after module reload (fail to receive
data after associate), but such cases are rarer than without the patch.
Signed-off-by: NStanislaw Gruszka <stf_xl@wp.pl>
Acked-by: NIvo van Doorn <IvDoorn@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Sometimes rxdesc descriptor provided by hardware contains invalid
(random) data. For example rxdesc.size can be bigger than actual
size of the buffer. When this happen rt2x00crypto_rx_insert_iv()
corrupt memory doing memmove outside of buffer boundaries.
Signed-off-by: NStanislaw Gruszka <stf_xl@wp.pl>
Acked-by: NIvo van Doorn <IvDoorn@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

* remove interrupt.g inclusion from netdevice.h -- not needed
* fixup fallout, add interrupt.h and hardirq.h back where needed.
Signed-off-by: NAlexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Avoid queue and run autowakeup_work when device is not present anymore.
That prevent rmmod and device remove crash introduced by:

commit 1c0bcf89
Author: Ivo van Doorn <ivdoorn@gmail.com>
Date:   Sat Apr 30 17:18:18 2011 +0200

    rt2x00: Add autowake support for USB hardware
Signed-off-by: NStanislaw Gruszka <stf_xl@wp.pl>
Acked-by: NIvo van Doorn <IvDoorn@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Semicolons are not necessary after switch/while/for/if braces
so remove them.
Signed-off-by: NJoe Perches <joe@perches.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>