The reference clock for the SGTL5000 is generated by a 26MHz crystal
oscillator on the Ka-Ro electronics STK5 eval kits. Use the correct
frequency setting in DTB.
Signed-off-by: NLothar Waßmann <LW@KARO-electronics.de>
Signed-off-by: NShawn Guo <shawnguo@kernel.org>

Though the keyboard and other driver will continue to support the legacy
"gpio-key,wakeup", "linux,wakeup" and "enable-sdio-wakeup" boolean
property to enable the wakeup source, "wakeup-source" is the new
standard binding.

This patch replaces all the legacy wakeup properties with the unified
"wakeup-source" property in order to avoid any futher copy-paste
duplication.

Cc: Sascha Hauer <kernel@pengutronix.de>
Signed-off-by: NSudeep Holla <sudeep.holla@arm.com>
Signed-off-by: NShawn Guo <shawnguo@kernel.org>

cd-gpios polarity should be changed to GPIO_ACTIVE_LOW and wp-gpios
should be changed to GPIO_ACTIVE_HIGH.
Otherwise, the SD may not work properly due to wrong polarity inversion
specified in DT after switch to common parsing function mmc_of_parse().
Signed-off-by: NDong Aisheng <aisheng.dong@freescale.com>
Acked-by: NShawn Guo <shawnguo@kernel.org>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

The DAI mode is and should be configured by the sound card driver as
codec and ssi have to be in the right modes to communicate with each
other. It is possible to operate the ssi unit or the codec in master mode,
sometimes even on the same board in different configurations.

With the latest changes in the fsl-ssi driver, the 'fsl,mode' property
is only handled as a fallback property. If the sound card sets the DAI
mode correctly, this fallback configuration is dropped.
Signed-off-by: NMarkus Pargmann <mpa@pengutronix.de>
Signed-off-by: NShawn Guo <shawn.guo@freescale.com>

'enable-active-low' is not a valid property for a GPIO controlled regulator.

According to Documentation/devicetree/bindings/regulator/gpio-regulator.txt:

"Optional properties:
...
- enable-active-high	: Polarity of GPIO is active high (default is low)."

,so the correct way to define an active-low GPIO controlled regulator is to
simply not pass 'enable-active-high'.
Signed-off-by: NFabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: NShawn Guo <shawn.guo@linaro.org>

This patch adds support for the Ka-Ro electronics GmbH TX53 modules.
There are two distinct module types. One with an LVDS display
interface and SATA support, the other with a parallel LCD
interface and no SATA interface.
Signed-off-by: NLothar Waßmann <LW@KARO-electronics.de>
Signed-off-by: NShawn Guo <shawn.guo@linaro.org>

The device tree specification recommends that generic name should be
used for nodes.  So instead of naming those fixed regulator nodes
arbitrarily, let's use the generic name 'regulator@num' for those nodes.
Signed-off-by: NShawn Guo <shawn.guo@linaro.org>

This adds support for the Ka-Ro TX53 System-On-Module.
As a baseboard is needed to operate it, only a *.dtsi and no Makefile entry.
Signed-off-by: NSteffen Trumtrar <s.trumtrar@pengutronix.de>
Signed-off-by: NShawn Guo <shawn.guo@linaro.org>