Some places were using PCI_CLASS_REVISION instead of PCI_REVISION_ID, so
they weren't converted by commit 44c10138
(PCI: Change all drivers to use pci_device->revision).
Signed-off-by: NSergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

The comment in the driver actually describes HPT37x's timing register layout,
which is different from HPT36x.  Fix it and reformat the comment, while at it.

Bump the driver version, accounting for several patches that forgot to do it.
Signed-off-by: NSergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

Based on:
http://lkml.indiana.edu/hypermail/linux/kernel/0908.2/01420.htmlSigned-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

These drivers inherited from the older 'hpt366' IDE driver the buggy timing
register masks in their set_piomode() metods. As a result, too low command
cycle active time is programmed for slow PIO modes.  Quite fortunately, it's
later "fixed up" by the set_dmamode() methods which also "helpfully" reprogram
the command timings, usually to PIO mode 4; unfortunately, setting an UltraDMA
mode #N also reprograms already set PIO data timings, usually to MWDMA mode #
max(N, 2) timings...

However, the drivers added some breakage of their own too:  the bit that they
set/clear to control the FIFO is sometimes wrong -- it's actually the MSB of
the command cycle setup time; also, setting it in DMA mode is wrong as this
bit is only for PIO actually and clearing it for PIO modes is not needed as
no mode in any timing table has it set...

Fix all this, inverting the masks while at it, like in the 'hpt366' and
'pata_hpt366' drivers; bump the drivers' versions, accounting for recent
patches that forgot to do it...
Signed-off-by: NSergei Shtylyov <sshtylyov@ru.mvista.com>
Cc: stable@kernel.org
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

We were never able to get docs for this out of Toshiba for years. Dave
Barnes produced a NetBSD driver however and from that we can fill in the
needed tables.

As we correct the PCI identifiers a bit also update the old ide generic driver
at the same time so it stays compiling.
Signed-off-by: NAlan Cox <alan@linux.intel.com>
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

Making the new stuff work broke some of the old chipsets. We need to go
back to the old set up values for these it seems. Unfortunately even with
documentation this is basically a mix of cargoculting and guesswork.

Chased down to the exact line by Gianluca.
Signed-off-by: NAlan Cox <alan@linux.intel.com>
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

Signed-off-by: NAlan Cox <alan@linux.intel.com>
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

Daniela Engert pointed out that there are some implementation notes for the
643 and 646 that deal with certain serialization rules. In theory we don't
need them because they apply when the motherboard decides not to retry PCI
requests for long enough and the chip is busy doing a DMA transfer on the
other channel.

The rule basically is "don't touch the taskfile of the other channel while
a DMA is in progress". To implement that we need to

- not issue a command on a channel when there is a DMA command queued
- not issue a DMA command on a channel when there are PIO commands queued
- use the alternative access to the interrupt source so that we do not
  touch altstatus or status on shared IRQ.

Updated to remote extra conditional check Bartlomiej noted and to remove
the variables for irq checks as the CMD648 doesn't have the underlying problem.
Signed-off-by: NAlan Cox <alan@linux.intel.com>
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

Bartlomiej pointed out that while this got fixed in the old driver whoever
did it didn't port it across.
Signed-off-by: NAlan Cox <alan@linux.intel.com>
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

Reported by Mikulas Patocka.

VIA VT82C586B + Transcend TS64GSSD25-M v0826 does not work in UDMA mode
Signed-off-by: NAlan Cox <alan@linux.intel.com>
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

In libata-sff, ata_sff_post_internal_cmd() directly calls ata_bmdma_stop()
instead of ap->ops->bmdma_stop(). This can be a problem for controllers
that use their own bmdma_stop for which the generic sff one isn't suitable
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

Add support for the ATA TRIM command in libata.  We translate a WRITE SAME 16
command with the unmap bit set into an ATA TRIM command and export enough
information in READ CAPACITY 16 and the block limits EVPD page so that the new
SCSI layer discard support will driver this for us.

Note that I hardcode the WRITE_SAME_16 opcode for now as the patch to introduce
the symbolic is not in 2.6.32 yet but only in the SCSI tree - as soon as it is
merged we can fix it up to properly use the symbolic name.
Signed-off-by: NChristoph Hellwig <hch@lst.de>
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

If ATA device failed FLUSH, it means that the device failed to write
out some amount of data and the error needs to be reported to upper
layers. As retries can't recover the lost data, FLUSH failures need to
be reported immediately in general.

However, if FLUSH fails due to transmission errors, the FLUSH needs to
be retried; otherwise, filesystems may switch to RO mode and/or raid
array may drop a drive for a random transmission glitch.

This condition can be rather easily reproduced on certain ahci
controllers which go through a PHY event after powersave mode switch +
ext4 combination.  Powersave mode switch is often closely followed by
flush from the filesystem failing the FLUSH with ATA bus error which
makes the filesystem code believe that data is lost and drop to RO
mode.  This was reported in the following bugzilla bug.

  http://bugzilla.kernel.org/show_bug.cgi?id=14543

This patch makes libata EH retry FLUSH if it wasn't failed by the
device.
Signed-off-by: NTejun Heo <tj@kernel.org>
Reported-by: NAndrey Vihrov <andrey.vihrov@gmail.com>
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

Enable device hot-plug support on Port multiplier fan-out ports
Signed-off-by: NAshish Kalra <Ashish.Kalra@freescale.com>
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

Alan Cox reported that cable detection sometimes works unreliably
for HPT3xxN and that the issue is fixed by adding debounce delay
as used by the vendor driver.

Sergei Shtylyov also noticed that debounce delay is needed for all
HPT37x and HPT3xxN chipsets according to vendor drivers.
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

The detection was reversed between primary and secondary ports.

Fix it to match hpt366 and the vendor driver.
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

sysfs attributes shouldn't require newlines. Make it possible to set the
link power management policy without a trailing newline.
Signed-off-by: NMatthew Garrett <mjg@redhat.com>
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

Signed-off-by: NOtavio Salvador <otavio@ossystems.com.br>
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

We can use the same ->pre_reset method for all HPT37x chipsets now.
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

I obseved there is a sata_async_notification() for every ahci
interrupt. But the async notification does nothing (this is hard
disk drive and no pmp). This cause cpu wastes some time on sntf
register access.

It appears ICH AHCI doesn't support SNotification register, but the
controller reports it does. After quirking it, the async notification
disappears.

PS. it appears all ICH don't support SNotification register from ICH
manual, don't know if we need quirk all ICH. I don't have machines
with all kinds of ICH.
Signed-off-by: NShaohua Li <shaohua.li@intel.com>
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

The following patch adds MSI support. Some platforms
may have broken MSI, so those are defaulted to use
legacy PCI interrupts.
Signed-off-by: NVivek Mahajan <vivek.mahajan@freescale.com>
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

Remove the experimental tag on Parallel ATA drivers. Though some of the
individual PATA drivers are still marked as experimental, as a group they can
hardly be considered to be, given they've been used in various distros for some
time.
Signed-off-by: NRobert Hancock <hancockrwd@gmail.com>
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

Use ARRAY_SIZE macro of kernel api instead.
Signed-off-by: NThiago Farina <tfransosi@gmail.com>
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

In via_init_one, when via_isa_bridges iterator reaches
PCI_DEVICE_ID_VIA_ANON and last but one via_isa_bridges bridge is
found but rev doesn't match, pci_dev_put(isa) is called twice.

Do pci_dev_put only once.
Signed-off-by: NJiri Slaby <jirislaby@gmail.com>
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

Tested on IXP425 + CS5536.
Signed-off-by: NKrzysztof Hałasa <khc@pm.waw.pl>
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

Missing _SDD is not an error.  Don't treat it as one.
Signed-off-by: NTejun Heo <tj@kernel.org>
Reported-by: NTakashi Iwai <tiwai@suse.de>
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

request_region should be used with release_region, not request_mem_region.

Geert Uytterhoeven pointed out that in the case of drivers/video/gbefb.c,
the problem is actually the other way around; request_mem_region should be
used instead of request_region.

The semantic patch that finds/fixes this problem is as follows:
(http://coccinelle.lip6.fr/)

// <smpl>
@r1@
expression start;
@@

request_region(start,...)

@b1@
expression r1.start;
@@

request_mem_region(start,...)

@depends on !b1@
expression r1.start;
expression E;
@@

- release_mem_region
+ release_region
  (start,E)
// </smpl>
Signed-off-by: NJulia Lawall <julia@diku.dk>
Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

TXx9 SPI bit rate is calculated by:
        fBR = (spi-baseclk) / (n + 1)
Fix calculation of min_speed_hz, max_speed_hz and n.
Signed-off-by: NAtsushi Nemoto <anemo@mba.ocn.ne.jp>
Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/sameo/mfd-2.6:
  mfd: Correct WM831X_MAX_ISEL_VALUE

These laptops often leave i8042 in a wierd state resulting in non-
operational touchpad and keyboard.
Signed-off-by: NAnisse Astier <anisse@astier.eu>
Signed-off-by: NDmitry Torokhov <dtor@mail.ru>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

* 'for-linus' of git://neil.brown.name/md:
  md: revert incorrect fix for read error handling in raid1.

Jon confirms that recent modprobe will look in /proc/cmdline, so these
cmdline options can still be used.

See http://bugzilla.kernel.org/show_bug.cgi?id=14164Reported-by: NAdam Williamson <awilliam@redhat.com>
Cc: stable@kernel.org
Signed-off-by: NRusty Russell <rusty@rustcorp.com.au>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

* 'upstream' of git://ftp.linux-mips.org/pub/scm/upstream-linus:
  MIPS: RB532: Fix devices.c compilation.
  MIPS: Fix MIPS I build.

* git://git.kernel.org/pub/scm/linux/kernel/git/wim/linux-2.6-watchdog:
  [PATCH] rc32434_wdt: fix compilation failure
  [WATCHDOG] rc32434_wdt.c: use resource_size()

On the parisc architecture we face for each and every loaded kernel module
this kernel "badness warning":
  sysfs: cannot create duplicate filename '/module/ac97_bus/sections/.text'
  Badness at fs/sysfs/dir.c:487

Reason for that is, that on parisc all kernel modules do have multiple
.text sections due to the usage of the -ffunction-sections compiler flag
which is needed to reach all jump targets on this platform.

An objdump on such a kernel module gives:
Sections:
Idx Name          Size      VMA       LMA       File off  Algn
  0 .note.gnu.build-id 00000024  00000000  00000000  00000034  2**2
                  CONTENTS, ALLOC, LOAD, READONLY, DATA
  1 .text         00000000  00000000  00000000  00000058  2**0
                  CONTENTS, ALLOC, LOAD, READONLY, CODE
  2 .text.ac97_bus_match 0000001c  00000000  00000000  00000058  2**2
                  CONTENTS, ALLOC, LOAD, READONLY, CODE
  3 .text         00000000  00000000  00000000  000000d4  2**0
                  CONTENTS, ALLOC, LOAD, READONLY, CODE
...
Since the .text sections are empty (size of 0 bytes) and won't be
loaded by the kernel module loader anyway, I don't see a reason
why such sections need to be listed under
/sys/module/<module_name>/sections/<section_name> either.

The attached patch does solve this issue by not exporting section
names which are empty.

This fixes bugzilla http://bugzilla.kernel.org/show_bug.cgi?id=14703Signed-off-by: NHelge Deller <deller@gmx.de>
CC: rusty@rustcorp.com.au
CC: akpm@linux-foundation.org
CC: James.Bottomley@HansenPartnership.com
CC: roland@redhat.com
CC: dave@hiauly1.hia.nrc.ca
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/lrg/voltage-2.6:
  regulator: Initialise wm831x structure pointor for ISINK driver

The version that made it into mainline missed the initialisation of the
chip handle.
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: NLiam Girdwood <lrg@slimlogic.co.uk>

We should now use dev_set_drvdata to set the driver driver_data field.
Signed-off-by: NFlorian Fainelli <florian@openwrt.org>
Patchwork: http://patchwork.linux-mips.org/patch/747/Signed-off-by: NRalf Baechle <ralf@linux-mips.org>