Add gpiolib registration for the GPIOs available on the
S3C64XX platform
Signed-off-by: NBen Dooks <ben-linux@fluff.org>

The gpiolib driver keeps its chip array to itself
and having a separate array for s3c-only gpios stops
any non-s3c gpio being used in one of the s3c specific
configuration calls.
Signed-off-by: NBen Dooks <ben-linux@fluff.org>

Move the common parts of the GPIO code into plat-s3c
for use with both the s3c24xx and s3c64xx systems.
Signed-off-by: NBen Dooks <ben-linux@fluff.org>

Define the gpio numbers for the S3C64XX GPIO banks
available on the S3C6400 and S3C6410.
Signed-off-by: NBen Dooks <ben-linux@fluff.org>

Add HSMMC0 device to SMDK6410.
Signed-off-by: NBen Dooks <ben-linux@fluff.org>

Move the definition for the hsmmc device to plat-s3c
to be shared between the s3c24xx and s3c64xx platforms.
Signed-off-by: NBen Dooks <ben-linux@fluff.org>

Add definitions for the external interrupt groups which accompany
the original IRQ_EINT from the s3c24xx series.
Signed-off-by: NBen Dooks <ben-linux@fluff.org>

Discard the 'void *' from the pointers used for the
virtual addresses when setting up the .virtual fields
of the io map to avoid implicit cast warnings
Signed-off-by: NBen Dooks <ben-linux@fluff.org>

 Index: linux.git/arch/arm/plat-s3c64xx/cpu.c
===================================================================

Some of the startup output can be reduced to
KERN_DEBUG from KERN_INFO as it is only really
useful when trying to debug kernel initialisation
problems.
Signed-off-by: NBen Dooks <ben-linux@fluff.org>

Add a basic defconfig for s3c6400 series machines.
Signed-off-by: NBen Dooks <ben-linux@fluff.org>

Initial machine support for the Samsung SMDK6410.
Signed-off-by: NBen Dooks <ben-linux@fluff.org>

Add the necessary code to support IRQ_EINT(x) on
the S3C64XX series of CPUs.

Note, since there is no GPIO configuration support
in the kernel, the irq set_type method does not
configure the relevant pin to interrupt.
Signed-off-by: NBen Dooks <ben-linux@fluff.org>

Add mapping for GPIO block in the static mappings.
Signed-off-by: NBen Dooks <ben-linux@fluff.org>

The original arch/arm/include/asm/hardware/vic.h was
written for the PL190 ARM VIC implementation, and as
such does not have any information about the PL192
version.

Add details about the PL192 and PL190 specific registers
and any changes between the two units.
Signed-off-by: NBen Dooks <ben-linux@fluff.org>

Add demux handling for the UART interrupts
generated by the VIC into their seperate IRQs
that the serial driver can register.
Signed-off-by: NBen Dooks <ben-linux@fluff.org>

Add support to the Samsung serial driver for the S3C6400
and S3C6410 serial ports.
Signed-off-by: NBen Dooks <ben-linux@fluff.org>

Add the PLL clock initialisation and clock registration
and include the clocks sourced via CLKDIVx for most of
the on-chip peripherals.
Signed-off-by: NBen Dooks <ben-linux@fluff.org>

Add TICK_MAX definition for the timer code
as the S3C64XX series have 32bit capable
PWM timers.
Signed-off-by: NBen Dooks <ben-linux@fluff.org>

Add the initial clocks definitions for the s3c6400
and s3c6410. Move the epll and ext clock from the
s3c2443 support into the common code.
Signed-off-by: NBen Dooks <ben-linux@fluff.org>

Add definitions for the s3c6400 epll and main pll
as well as functions to decode the rate. Add
Signed-off-by: NBen Dooks <ben-linux@fluff.org>

Add the common initialisation code for both the
S3C6400 and S3C6410, the UART registration.
Signed-off-by: NBen Dooks <ben-linux@fluff.org>

Add the physical to virtual memory mapping and the
necessary interrupt demuxing for the PWM timer blocks.
Signed-off-by: NBen Dooks <ben-linux@fluff.org>

The pwm-clock.c needs <mach/map.h> which is included
via other means on S3C24XX systems, so ensure it is
explicitly included.

Remove the includes of regs-clock.h and regs-gpio.h as
these are not needed by the build.
Signed-off-by: NBen Dooks <ben-linux@fluff.org>

Add the necessary support for the timer on the
S3C6400 and S3C6410 by adding <mach/tick.h>
Signed-off-by: NBen Dooks <ben-linux@fluff.org>

Add and initialise the two VIC (PL192) found on
the S3C64XX series CPUs.
Signed-off-by: NBen Dooks <ben-linux@fluff.org>

Initial support for the Samsung S3C6410 SoC.
Signed-off-by: NBen Dooks <ben-linux@fluff.org>

Initialise the basic physical to virtual mappings and
then detect the CPU that the system is being run on so
that the cpu code code can call the correct initialisation
code.
Signed-off-by: NBen Dooks <ben-linux@fluff.org>

Add IRQ definitions for the VIC0 and VIC1 interrupts
on the S3C6400 and S3C6410 SoCs.
Signed-off-by: NBen Dooks <ben-linux@fluff.org>

Add resources and information for the UART deviecs
on the S3C64XX CPUs.
Signed-off-by: NBen Dooks <ben-linux@fluff.org>

Add the necessary defines for <mach/uncompress.h>
to function and build an working header code block.
Signed-off-by: NBen Doioks <ben-linux@fluff.org>

Initial clock register defines.
Signed-off-by: NBen Dooks <ben-linux@fluff.org>

Add the necessary support for the kernel low-level
debug macros via <mach/debug-macro.S>
Signed-off-by: NBen Dooks <ben-linux@fluff.org>

Add the include for the interrupt entry macros needed
to be included by <mach/entry-macro.S> for the kernel
interrupt handler.
Signed-off-by: NBen Dooks <ben-linux@fluff.org>

Add the initial header files for the S3C64XX support to satisfy the
minimal requirements to build a kernel. Some definitions will therefore
be placeholders or empty functions that will ensure that the system can
build and have base functionality. These will be filled in at a later
date.
Signed-off-by: NBen Dooks <ben-linux@fluff.org>

Add the initial PLAT_S3C64XX support files
and directory structure.
Signed-off-by: NBen Dooks <ben-linux@fluff.org>

Split the timer pending code out to a seperate per-machine
header so that when compiling for mach-s3c2410 or mach-s3c24a0
we can use the right timer code without having to #ifdef the
timer driver.
Signed-off-by: NBen Dooks <ben-linux@fluff.org>

Initial architecture support for the S3C24A0 ARCH_S3C24A0.

We don't yet add an kconfig entry in the main arch/arm/Kconfig
file as the series is not complete, so that is left until enough
support is in to be useful.
Signed-off-by: NBen Dooks <ben-linux@fluff.org>

Split the map.h definitions into common S3C24XX code by
adding arch/arm/plat-s3c24xx/include/plat/map.h and
altering the machine specific header for the S3C24A0.

As we add a new <plat/map.h> we move the original one
in arch/arm/plat-s3c include directory to be called
map-base.h to distinguish the two files.
Signed-off-by: NBen Dooks <ben-linux@fluff.org>

Add serial support for S3C24A0, based on current S3C2410
UART driver. It adds necessary new defines in regs-serial.h
for S3C24A0 and the code to support this device in
drivers/serial/s3c24a0.c
Signed-off-by: NSandeep Patil <sandeep.patil@azingo.com>
Signed-off-by: NBen Dooks <ben-linux@fluff.org>

Add the necessary debug macros for the S3C24A0 to enable
kernel debugging, and fix a bug with selecting the wrong
default debug implementation from the base include.
Signed-off-by: NBen Dooks <ben-linux@fluff.org>