- 05 3月, 2012 3 次提交
-
-
由 Paul Mackerras 提交于
This adds an array that parallels the guest hashed page table (HPT), that is, it has one entry per HPTE, used to store the guest's view of the second doubleword of the corresponding HPTE. The first doubleword in the HPTE is the same as the guest's idea of it, so we don't need to store a copy, but the second doubleword in the HPTE has the real page number rather than the guest's logical page number. This allows us to remove the back_translate() and reverse_xlate() functions. This "reverse mapping" array is vmalloc'd, meaning that to access it in real mode we have to walk the kernel's page tables explicitly. That is done by the new real_vmalloc_addr() function. (In fact this returns an address in the linear mapping, so the result is usable both in real mode and in virtual mode.) There are also some minor cleanups here: moving the definitions of HPT_ORDER etc. to a header file and defining HPT_NPTE for HPT_NPTEG << 3. Signed-off-by: NPaul Mackerras <paulus@samba.org> Signed-off-by: NAlexander Graf <agraf@suse.de> Signed-off-by: NAvi Kivity <avi@redhat.com>
-
由 Scott Wood 提交于
Decrementers are now properly driven by TCR/TSR, and the guest has full read/write access to these registers. The decrementer keeps ticking (and setting the TSR bit) regardless of whether the interrupts are enabled with TCR. The decrementer stops at zero, rather than going negative. Decrementers (and FITs, once implemented) are delivered as level-triggered interrupts -- dequeued when the TSR bit is cleared, not on delivery. Signed-off-by: NLiu Yu <yu.liu@freescale.com> [scottwood@freescale.com: significant changes] Signed-off-by: NScott Wood <scottwood@freescale.com> Signed-off-by: NAlexander Graf <agraf@suse.de> Signed-off-by: NAvi Kivity <avi@redhat.com>
-
由 Scott Wood 提交于
This allows additional registers to be accessed by the guest in PR-mode KVM without trapping. SPRG4-7 are readable from userspace. On booke, KVM will sync these registers when it enters the guest, so that accesses from guest userspace will work. The guest kernel, OTOH, must consistently use either the real registers or the shared area between exits. This also applies to the already-paravirted SPRG3. On non-booke, it's not clear to what extent SPRG4-7 are supported (they're not architected for book3s, but exist on at least some classic chips). They are copied in the get/set regs ioctls, but I do not see any non-booke emulation. I also do not see any syncing with real registers (in PR-mode) including the user-readable SPRG3. This patch should not make that situation any worse. Signed-off-by: NScott Wood <scottwood@freescale.com> Signed-off-by: NAlexander Graf <agraf@suse.de> Signed-off-by: NAvi Kivity <avi@redhat.com>
-
- 26 9月, 2011 4 次提交
-
-
由 Paul Mackerras 提交于
With a KVM guest operating in SMT4 mode (i.e. 4 hardware threads per core), whenever a CPU goes idle, we have to pull all the other hardware threads in the core out of the guest, because the H_CEDE hcall is handled in the kernel. This is inefficient. This adds code to book3s_hv_rmhandlers.S to handle the H_CEDE hcall in real mode. When a guest vcpu does an H_CEDE hcall, we now only exit to the kernel if all the other vcpus in the same core are also idle. Otherwise we mark this vcpu as napping, save state that could be lost in nap mode (mainly GPRs and FPRs), and execute the nap instruction. When the thread wakes up, because of a decrementer or external interrupt, we come back in at kvm_start_guest (from the system reset interrupt vector), find the `napping' flag set in the paca, and go to the resume path. This has some other ramifications. First, when starting a core, we now start all the threads, both those that are immediately runnable and those that are idle. This is so that we don't have to pull all the threads out of the guest when an idle thread gets a decrementer interrupt and wants to start running. In fact the idle threads will all start with the H_CEDE hcall returning; being idle they will just do another H_CEDE immediately and go to nap mode. This required some changes to kvmppc_run_core() and kvmppc_run_vcpu(). These functions have been restructured to make them simpler and clearer. We introduce a level of indirection in the wait queue that gets woken when external and decrementer interrupts get generated for a vcpu, so that we can have the 4 vcpus in a vcore using the same wait queue. We need this because the 4 vcpus are being handled by one thread. Secondly, when we need to exit from the guest to the kernel, we now have to generate an IPI for any napping threads, because an HDEC interrupt doesn't wake up a napping thread. Thirdly, we now need to be able to handle virtual external interrupts and decrementer interrupts becoming pending while a thread is napping, and deliver those interrupts to the guest when the thread wakes. This is done in kvmppc_cede_reentry, just before fast_guest_return. Finally, since we are not using the generic kvm_vcpu_block for book3s_hv, and hence not calling kvm_arch_vcpu_runnable, we can remove the #ifdef from kvm_arch_vcpu_runnable. Signed-off-by: NPaul Mackerras <paulus@samba.org> Signed-off-by: NAlexander Graf <agraf@suse.de>
-
由 Paul Mackerras 提交于
This simplifies the way that the book3s_pr makes the transition to real mode when entering the guest. We now call kvmppc_entry_trampoline (renamed from kvmppc_rmcall) in the base kernel using a normal function call instead of doing an indirect call through a pointer in the vcpu. If kvm is a module, the module loader takes care of generating a trampoline as it does for other calls to functions outside the module. kvmppc_entry_trampoline then disables interrupts and jumps to kvmppc_handler_trampoline_enter in real mode using an rfi[d]. That then uses the link register as the address to return to (potentially in module space) when the guest exits. This also simplifies the way that we call the Linux interrupt handler when we exit the guest due to an external, decrementer or performance monitor interrupt. Instead of turning on the MMU, then deciding that we need to call the Linux handler and turning the MMU back off again, we now go straight to the handler at the point where we would turn the MMU on. The handler will then return to the virtual-mode code (potentially in the module). Along the way, this moves the setting and clearing of the HID5 DCBZ32 bit into real-mode interrupts-off code, and also makes sure that we clear the MSR[RI] bit before loading values into SRR0/1. The net result is that we no longer need any code addresses to be stored in vcpu->arch. Signed-off-by: NPaul Mackerras <paulus@samba.org> Signed-off-by: NAlexander Graf <agraf@suse.de>
-
由 Alexander Graf 提交于
There are multiple features in PowerPC KVM that can now be enabled depending on the user's wishes. Some of the combinations don't make sense or don't work though. So this patch adds a way to check if the executing environment would actually be able to run the guest properly. It also adds sanity checks if PVR is set (should always be true given the current code flow), if PAPR is only used with book3s_64 where it works and that HV KVM is only used in PAPR mode. Signed-off-by: NAlexander Graf <agraf@suse.de>
-
由 Alexander Graf 提交于
When running a PAPR guest, some things change. The privilege level drops from hypervisor to supervisor, SDR1 gets treated differently and we interpret hypercalls. For bisectability sake, add the flag now, but only enable it when all the support code is there. Signed-off-by: NAlexander Graf <agraf@suse.de>
-
- 12 7月, 2011 10 次提交
-
-
由 Paul Mackerras 提交于
This adds support for running KVM guests in supervisor mode on those PPC970 processors that have a usable hypervisor mode. Unfortunately, Apple G5 machines have supervisor mode disabled (MSR[HV] is forced to 1), but the YDL PowerStation does have a usable hypervisor mode. There are several differences between the PPC970 and POWER7 in how guests are managed. These differences are accommodated using the CPU_FTR_ARCH_201 (PPC970) and CPU_FTR_ARCH_206 (POWER7) CPU feature bits. Notably, on PPC970: * The LPCR, LPID or RMOR registers don't exist, and the functions of those registers are provided by bits in HID4 and one bit in HID0. * External interrupts can be directed to the hypervisor, but unlike POWER7 they are masked by MSR[EE] in non-hypervisor modes and use SRR0/1 not HSRR0/1. * There is no virtual RMA (VRMA) mode; the guest must use an RMO (real mode offset) area. * The TLB entries are not tagged with the LPID, so it is necessary to flush the whole TLB on partition switch. Furthermore, when switching partitions we have to ensure that no other CPU is executing the tlbie or tlbsync instructions in either the old or the new partition, otherwise undefined behaviour can occur. * The PMU has 8 counters (PMC registers) rather than 6. * The DSCR, PURR, SPURR, AMR, AMOR, UAMOR registers don't exist. * The SLB has 64 entries rather than 32. * There is no mediated external interrupt facility, so if we switch to a guest that has a virtual external interrupt pending but the guest has MSR[EE] = 0, we have to arrange to have an interrupt pending for it so that we can get control back once it re-enables interrupts. We do that by sending ourselves an IPI with smp_send_reschedule after hard-disabling interrupts. Signed-off-by: NPaul Mackerras <paulus@samba.org> Signed-off-by: NAlexander Graf <agraf@suse.de>
-
由 Paul Mackerras 提交于
This adds infrastructure which will be needed to allow book3s_hv KVM to run on older POWER processors, including PPC970, which don't support the Virtual Real Mode Area (VRMA) facility, but only the Real Mode Offset (RMO) facility. These processors require a physically contiguous, aligned area of memory for each guest. When the guest does an access in real mode (MMU off), the address is compared against a limit value, and if it is lower, the address is ORed with an offset value (from the Real Mode Offset Register (RMOR)) and the result becomes the real address for the access. The size of the RMA has to be one of a set of supported values, which usually includes 64MB, 128MB, 256MB and some larger powers of 2. Since we are unlikely to be able to allocate 64MB or more of physically contiguous memory after the kernel has been running for a while, we allocate a pool of RMAs at boot time using the bootmem allocator. The size and number of the RMAs can be set using the kvm_rma_size=xx and kvm_rma_count=xx kernel command line options. KVM exports a new capability, KVM_CAP_PPC_RMA, to signal the availability of the pool of preallocated RMAs. The capability value is 1 if the processor can use an RMA but doesn't require one (because it supports the VRMA facility), or 2 if the processor requires an RMA for each guest. This adds a new ioctl, KVM_ALLOCATE_RMA, which allocates an RMA from the pool and returns a file descriptor which can be used to map the RMA. It also returns the size of the RMA in the argument structure. Having an RMA means we will get multiple KMV_SET_USER_MEMORY_REGION ioctl calls from userspace. To cope with this, we now preallocate the kvm->arch.ram_pginfo array when the VM is created with a size sufficient for up to 64GB of guest memory. Subsequently we will get rid of this array and use memory associated with each memslot instead. This moves most of the code that translates the user addresses into host pfns (page frame numbers) out of kvmppc_prepare_vrma up one level to kvmppc_core_prepare_memory_region. Also, instead of having to look up the VMA for each page in order to check the page size, we now check that the pages we get are compound pages of 16MB. However, if we are adding memory that is mapped to an RMA, we don't bother with calling get_user_pages_fast and instead just offset from the base pfn for the RMA. Typically the RMA gets added after vcpus are created, which makes it inconvenient to have the LPCR (logical partition control register) value in the vcpu->arch struct, since the LPCR controls whether the processor uses RMA or VRMA for the guest. This moves the LPCR value into the kvm->arch struct and arranges for the MER (mediated external request) bit, which is the only bit that varies between vcpus, to be set in assembly code when going into the guest if there is a pending external interrupt request. Signed-off-by: NPaul Mackerras <paulus@samba.org> Signed-off-by: NAlexander Graf <agraf@suse.de>
-
由 Paul Mackerras 提交于
This lifts the restriction that book3s_hv guests can only run one hardware thread per core, and allows them to use up to 4 threads per core on POWER7. The host still has to run single-threaded. This capability is advertised to qemu through a new KVM_CAP_PPC_SMT capability. The return value of the ioctl querying this capability is the number of vcpus per virtual CPU core (vcore), currently 4. To use this, the host kernel should be booted with all threads active, and then all the secondary threads should be offlined. This will put the secondary threads into nap mode. KVM will then wake them from nap mode and use them for running guest code (while they are still offline). To wake the secondary threads, we send them an IPI using a new xics_wake_cpu() function, implemented in arch/powerpc/sysdev/xics/icp-native.c. In other words, at this stage we assume that the platform has a XICS interrupt controller and we are using icp-native.c to drive it. Since the woken thread will need to acknowledge and clear the IPI, we also export the base physical address of the XICS registers using kvmppc_set_xics_phys() for use in the low-level KVM book3s code. When a vcpu is created, it is assigned to a virtual CPU core. The vcore number is obtained by dividing the vcpu number by the number of threads per core in the host. This number is exported to userspace via the KVM_CAP_PPC_SMT capability. If qemu wishes to run the guest in single-threaded mode, it should make all vcpu numbers be multiples of the number of threads per core. We distinguish three states of a vcpu: runnable (i.e., ready to execute the guest), blocked (that is, idle), and busy in host. We currently implement a policy that the vcore can run only when all its threads are runnable or blocked. This way, if a vcpu needs to execute elsewhere in the kernel or in qemu, it can do so without being starved of CPU by the other vcpus. When a vcore starts to run, it executes in the context of one of the vcpu threads. The other vcpu threads all go to sleep and stay asleep until something happens requiring the vcpu thread to return to qemu, or to wake up to run the vcore (this can happen when another vcpu thread goes from busy in host state to blocked). It can happen that a vcpu goes from blocked to runnable state (e.g. because of an interrupt), and the vcore it belongs to is already running. In that case it can start to run immediately as long as the none of the vcpus in the vcore have started to exit the guest. We send the next free thread in the vcore an IPI to get it to start to execute the guest. It synchronizes with the other threads via the vcore->entry_exit_count field to make sure that it doesn't go into the guest if the other vcpus are exiting by the time that it is ready to actually enter the guest. Note that there is no fixed relationship between the hardware thread number and the vcpu number. Hardware threads are assigned to vcpus as they become runnable, so we will always use the lower-numbered hardware threads in preference to higher-numbered threads if not all the vcpus in the vcore are runnable, regardless of which vcpus are runnable. Signed-off-by: NPaul Mackerras <paulus@samba.org> Signed-off-by: NAlexander Graf <agraf@suse.de>
-
由 David Gibson 提交于
This improves I/O performance for guests using the PAPR paravirtualization interface by making the H_PUT_TCE hcall faster, by implementing it in real mode. H_PUT_TCE is used for updating virtual IOMMU tables, and is used both for virtual I/O and for real I/O in the PAPR interface. Since this moves the IOMMU tables into the kernel, we define a new KVM_CREATE_SPAPR_TCE ioctl to allow qemu to create the tables. The ioctl returns a file descriptor which can be used to mmap the newly created table. The qemu driver models use them in the same way as userspace managed tables, but they can be updated directly by the guest with a real-mode H_PUT_TCE implementation, reducing the number of host/guest context switches during guest IO. There are certain circumstances where it is useful for userland qemu to write to the TCE table even if the kernel H_PUT_TCE path is used most of the time. Specifically, allowing this will avoid awkwardness when we need to reset the table. More importantly, we will in the future need to write the table in order to restore its state after a checkpoint resume or migration. Signed-off-by: NDavid Gibson <david@gibson.dropbear.id.au> Signed-off-by: NPaul Mackerras <paulus@samba.org> Signed-off-by: NAlexander Graf <agraf@suse.de>
-
由 Paul Mackerras 提交于
This adds the infrastructure for handling PAPR hcalls in the kernel, either early in the guest exit path while we are still in real mode, or later once the MMU has been turned back on and we are in the full kernel context. The advantage of handling hcalls in real mode if possible is that we avoid two partition switches -- and this will become more important when we support SMT4 guests, since a partition switch means we have to pull all of the threads in the core out of the guest. The disadvantage is that we can only access the kernel linear mapping, not anything vmalloced or ioremapped, since the MMU is off. This also adds code to handle the following hcalls in real mode: H_ENTER Add an HPTE to the hashed page table H_REMOVE Remove an HPTE from the hashed page table H_READ Read HPTEs from the hashed page table H_PROTECT Change the protection bits in an HPTE H_BULK_REMOVE Remove up to 4 HPTEs from the hashed page table H_SET_DABR Set the data address breakpoint register Plus code to handle the following hcalls in the kernel: H_CEDE Idle the vcpu until an interrupt or H_PROD hcall arrives H_PROD Wake up a ceded vcpu H_REGISTER_VPA Register a virtual processor area (VPA) The code that runs in real mode has to be in the base kernel, not in the module, if KVM is compiled as a module. The real-mode code can only access the kernel linear mapping, not vmalloc or ioremap space. Signed-off-by: NPaul Mackerras <paulus@samba.org> Signed-off-by: NAlexander Graf <agraf@suse.de>
-
由 Paul Mackerras 提交于
This adds support for KVM running on 64-bit Book 3S processors, specifically POWER7, in hypervisor mode. Using hypervisor mode means that the guest can use the processor's supervisor mode. That means that the guest can execute privileged instructions and access privileged registers itself without trapping to the host. This gives excellent performance, but does mean that KVM cannot emulate a processor architecture other than the one that the hardware implements. This code assumes that the guest is running paravirtualized using the PAPR (Power Architecture Platform Requirements) interface, which is the interface that IBM's PowerVM hypervisor uses. That means that existing Linux distributions that run on IBM pSeries machines will also run under KVM without modification. In order to communicate the PAPR hypercalls to qemu, this adds a new KVM_EXIT_PAPR_HCALL exit code to include/linux/kvm.h. Currently the choice between book3s_hv support and book3s_pr support (i.e. the existing code, which runs the guest in user mode) has to be made at kernel configuration time, so a given kernel binary can only do one or the other. This new book3s_hv code doesn't support MMIO emulation at present. Since we are running paravirtualized guests, this isn't a serious restriction. With the guest running in supervisor mode, most exceptions go straight to the guest. We will never get data or instruction storage or segment interrupts, alignment interrupts, decrementer interrupts, program interrupts, single-step interrupts, etc., coming to the hypervisor from the guest. Therefore this introduces a new KVMTEST_NONHV macro for the exception entry path so that we don't have to do the KVM test on entry to those exception handlers. We do however get hypervisor decrementer, hypervisor data storage, hypervisor instruction storage, and hypervisor emulation assist interrupts, so we have to handle those. In hypervisor mode, real-mode accesses can access all of RAM, not just a limited amount. Therefore we put all the guest state in the vcpu.arch and use the shadow_vcpu in the PACA only for temporary scratch space. We allocate the vcpu with kzalloc rather than vzalloc, and we don't use anything in the kvmppc_vcpu_book3s struct, so we don't allocate it. We don't have a shared page with the guest, but we still need a kvm_vcpu_arch_shared struct to store the values of various registers, so we include one in the vcpu_arch struct. The POWER7 processor has a restriction that all threads in a core have to be in the same partition. MMU-on kernel code counts as a partition (partition 0), so we have to do a partition switch on every entry to and exit from the guest. At present we require the host and guest to run in single-thread mode because of this hardware restriction. This code allocates a hashed page table for the guest and initializes it with HPTEs for the guest's Virtual Real Memory Area (VRMA). We require that the guest memory is allocated using 16MB huge pages, in order to simplify the low-level memory management. This also means that we can get away without tracking paging activity in the host for now, since huge pages can't be paged or swapped. This also adds a few new exports needed by the book3s_hv code. Signed-off-by: NPaul Mackerras <paulus@samba.org> Signed-off-by: NAlexander Graf <agraf@suse.de>
-
由 Paul Mackerras 提交于
This moves the slb field, which represents the state of the emulated SLB, from the kvmppc_vcpu_book3s struct to the kvm_vcpu_arch, and the hpte_hash_[v]pte[_long] fields from kvm_vcpu_arch to kvmppc_vcpu_book3s. This is in accord with the principle that the kvm_vcpu_arch struct represents the state of the emulated CPU, and the kvmppc_vcpu_book3s struct holds the auxiliary data structures used in the emulation. Signed-off-by: NPaul Mackerras <paulus@samba.org> Signed-off-by: NAlexander Graf <agraf@suse.de>
-
由 Liu Yu 提交于
Dynamically assign host PIDs to guest PIDs, splitting each guest PID into multiple host (shadow) PIDs based on kernel/user and MSR[IS/DS]. Use both PID0 and PID1 so that the shadow PIDs for the right mode can be selected, that correspond both to guest TID = zero and guest TID = guest PID. This allows us to significantly reduce the frequency of needing to invalidate the entire TLB. When the guest mode or PID changes, we just update the host PID0/PID1. And since the allocation of shadow PIDs is global, multiple guests can share the TLB without conflict. Note that KVM does not yet support the guest setting PID1 or PID2 to a value other than zero. This will need to be fixed for nested KVM to work. Until then, we enforce the requirement for guest PID1/PID2 to stay zero by failing the emulation if the guest tries to set them to something else. Signed-off-by: NLiu Yu <yu.liu@freescale.com> Signed-off-by: NScott Wood <scottwood@freescale.com> Signed-off-by: NAlexander Graf <agraf@suse.de>
-
由 Scott Wood 提交于
This is done lazily. The SPE save will be done only if the guest has used SPE since the last preemption or heavyweight exit. Restore will be done only on demand, when enabling MSR_SPE in the shadow MSR, in response to an SPE fault or mtmsr emulation. For SPEFSCR, Linux already switches it on context switch (non-lazily), so the only remaining bit is to save it between qemu and the guest. Signed-off-by: NLiu Yu <yu.liu@freescale.com> Signed-off-by: NScott Wood <scottwood@freescale.com> Signed-off-by: NAlexander Graf <agraf@suse.de>
-
由 Scott Wood 提交于
Keep the guest MSR and the guest-mode true MSR separate, rather than modifying the guest MSR on each guest entry to produce a true MSR. Any bits which should be modified based on guest MSR must be explicitly propagated from vcpu->arch.shared->msr to vcpu->arch.shadow_msr in kvmppc_set_msr(). While we're modifying the guest entry code, reorder a few instructions to bury some load latencies. Signed-off-by: NScott Wood <scottwood@freescale.com> Signed-off-by: NAlexander Graf <agraf@suse.de>
-
- 22 5月, 2011 2 次提交
-
-
由 Scott Wood 提交于
Signed-off-by: NScott Wood <scottwood@freescale.com> Signed-off-by: NAlexander Graf <agraf@suse.de>
-
由 Scott Wood 提交于
Linux doesn't use USPRG0 (now renamed VRSAVE in the architecture, even when Altivec isn't involved), but a guest might. Signed-off-by: NScott Wood <scottwood@freescale.com> Signed-off-by: NAlexander Graf <agraf@suse.de>
-
- 11 5月, 2011 1 次提交
-
-
由 Bharat Bhushan 提交于
Following dump is observed on host when clearing the exit timing counters [root@p1021mds kvm]# echo -n 'c' > vm1200_vcpu0_timing INFO: task echo:1276 blocked for more than 120 seconds. "echo 0 > /proc/sys/kernel/hung_task_timeout_secs" disables this message. echo D 0ff5bf94 0 1276 1190 0x00000000 Call Trace: [c2157e40] [c0007908] __switch_to+0x9c/0xc4 [c2157e50] [c040293c] schedule+0x1b4/0x3bc [c2157e90] [c04032dc] __mutex_lock_slowpath+0x74/0xc0 [c2157ec0] [c00369e4] kvmppc_init_timing_stats+0x20/0xb8 [c2157ed0] [c0036b00] kvmppc_exit_timing_write+0x84/0x98 [c2157ef0] [c00b9f90] vfs_write+0xc0/0x16c [c2157f10] [c00ba284] sys_write+0x4c/0x90 [c2157f40] [c000e320] ret_from_syscall+0x0/0x3c The vcpu->mutex is used by kvm_ioctl_* (KVM_RUN etc) and same was used when clearing the stats (in kvmppc_init_timing_stats()). What happens is that when the guest is idle then it held the vcpu->mutx. While the exiting timing process waits for guest to release the vcpu->mutex and a hang state is reached. Now using seprate lock for exit timing stats. Signed-off-by: NBharat Bhushan <Bharat.Bhushan@freescale.com> Acked-by: NAlexander Graf <agraf@suse.de> Signed-off-by: NAvi Kivity <avi@redhat.com>
-
- 24 10月, 2010 9 次提交
-
-
由 Alexander Graf 提交于
On Book3s_32 the tlbie instruction flushed effective addresses by the mask 0x0ffff000. This is pretty hard to reflect with a hash that hashes ~0xfff, so to speed up that target we should also keep a special hash around for it. Signed-off-by: NAlexander Graf <agraf@suse.de> Signed-off-by: NAvi Kivity <avi@redhat.com>
-
由 Alexander Graf 提交于
So far we've been running all code without locking of any sort. This wasn't really an issue because I didn't see any parallel access to the shadow MMU code coming. But then I started to implement dirty bitmapping to MOL which has the video code in its own thread, so suddenly we had the dirty bitmap code run in parallel to the shadow mmu code. And with that came trouble. So I went ahead and made the MMU modifying functions as parallelizable as I could think of. I hope I didn't screw up too much RCU logic :-). If you know your way around RCU and locking and what needs to be done when, please take a look at this patch. Signed-off-by: NAlexander Graf <agraf@suse.de> Signed-off-by: NAvi Kivity <avi@redhat.com>
-
由 Alexander Graf 提交于
We will be introducing a method to project the shared page in guest context. As soon as we're talking about this coupling, the shared page is colled magic page. This patch introduces simple defines, so the follow-up patches are easier to read. Signed-off-by: NAlexander Graf <agraf@suse.de> Signed-off-by: NAvi Kivity <avi@redhat.com>
-
由 Alexander Graf 提交于
On PowerPC it's very normal to not support all of the physical RAM in real mode. To check if we're matching on the shared page or not, we need to know the limits so we can restrain ourselves to that range. So let's make it a define instead of open-coding it. And while at it, let's also increase it. Signed-off-by: NAlexander Graf <agraf@suse.de> v2 -> v3: - RMO -> PAM (non-magic page) Signed-off-by: NAvi Kivity <avi@redhat.com>
-
由 Alexander Graf 提交于
When in kernel mode there are 4 additional registers available that are simple data storage. Instead of exiting to the hypervisor to read and write those, we can just share them with the guest using the page. This patch converts all users of the current field to the shared page. Signed-off-by: NAlexander Graf <agraf@suse.de> Signed-off-by: NAvi Kivity <avi@redhat.com>
-
由 Alexander Graf 提交于
The SRR0 and SRR1 registers contain cached values of the PC and MSR respectively. They get written to by the hypervisor when an interrupt occurs or directly by the kernel. They are also used to tell the rfi(d) instruction where to jump to. Because it only gets touched on defined events that, it's very simple to share with the guest. Hypervisor and guest both have full r/w access. This patch converts all users of the current field to the shared page. Signed-off-by: NAlexander Graf <agraf@suse.de> Signed-off-by: NAvi Kivity <avi@redhat.com>
-
由 Alexander Graf 提交于
The DAR register contains the address a data page fault occured at. This register behaves pretty much like a simple data storage register that gets written to on data faults. There is no hypervisor interaction required on read or write. This patch converts all users of the current field to the shared page. Signed-off-by: NAlexander Graf <agraf@suse.de> Signed-off-by: NAvi Kivity <avi@redhat.com>
-
由 Alexander Graf 提交于
One of the most obvious registers to share with the guest directly is the MSR. The MSR contains the "interrupts enabled" flag which the guest has to toggle in critical sections. So in order to bring the overhead of interrupt en- and disabling down, let's put msr into the shared page. Keep in mind that even though you can fully read its contents, writing to it doesn't always update all state. There are a few safe fields that don't require hypervisor interaction. See the documentation for a list of MSR bits that are safe to be set from inside the guest. Signed-off-by: NAlexander Graf <agraf@suse.de> Signed-off-by: NAvi Kivity <avi@redhat.com>
-
由 Alexander Graf 提交于
For transparent variable sharing between the hypervisor and guest, I introduce a shared page. This shared page will contain all the registers the guest can read and write safely without exiting guest context. This patch only implements the stubs required for the basic structure of the shared page. The actual register moving follows. Signed-off-by: NAlexander Graf <agraf@suse.de> Signed-off-by: NAvi Kivity <avi@redhat.com>
-
- 01 8月, 2010 2 次提交
-
-
由 Joerg Roedel 提交于
This patch converts unnecessary divide and modulo operations in the KVM large page related code into logical operations. This allows to convert gfn_t to u64 while not breaking 32 bit builds. Signed-off-by: NJoerg Roedel <joerg.roedel@amd.com> Signed-off-by: NMarcelo Tosatti <mtosatti@redhat.com>
-
由 Alexander Graf 提交于
We just introduced generic functions to handle shadow pages on PPC. This patch makes the respective backends make use of them, getting rid of a lot of duplicate code along the way. Signed-off-by: NAlexander Graf <agraf@suse.de> Signed-off-by: NMarcelo Tosatti <mtosatti@redhat.com>
-
- 17 5月, 2010 6 次提交
-
-
由 Alexander Graf 提交于
There are some pieces in the code that I overlooked that still use u64s instead of longs. This slows down 32 bit hosts unnecessarily, so let's just move them to ulong. Signed-off-by: NAlexander Graf <agraf@suse.de> Signed-off-by: NAvi Kivity <avi@redhat.com>
-
由 Alexander Graf 提交于
The shadow vcpu now contains some fields we don't use from the vcpu anymore. Access to them happens using inline functions that happily use the shadow vcpu fields. So let's now ifdef them out to booke only and add asm-offsets. Signed-off-by: NAlexander Graf <agraf@suse.de> Signed-off-by: NAvi Kivity <avi@redhat.com>
-
由 Alexander Graf 提交于
Upstream recently added a new name for PPC64: Book3S_64. So instead of using CONFIG_PPC64 we should use CONFIG_PPC_BOOK3S consotently. That makes understanding the code easier (I hope). Signed-off-by: NAlexander Graf <agraf@suse.de> Signed-off-by: NAvi Kivity <avi@redhat.com>
-
由 Alexander Graf 提交于
Bool defaults to at least byte width. We usually only want to waste a single bit on this. So let's move all the bool values to bitfields, potentially saving memory. Signed-off-by: NAlexander Graf <agraf@suse.de> Signed-off-by: NAvi Kivity <avi@redhat.com>
-
由 Alexander Graf 提交于
MOL uses its own hypercall interface to call back into userspace when the guest wants to do something. So let's implement that as an exit reason, specify it with a CAP and only really use it when userspace wants us to. The only user of it so far is MOL. Signed-off-by: NAlexander Graf <agraf@suse.de> Signed-off-by: NAvi Kivity <avi@redhat.com>
-
由 Alexander Graf 提交于
DSISR is only defined as 32 bits wide. So let's reflect that in the structs too. Signed-off-by: NAlexander Graf <agraf@suse.de> Signed-off-by: NAvi Kivity <avi@redhat.com>
-
- 25 4月, 2010 3 次提交
-
-
由 Alexander Graf 提交于
The guest I was trying to get to run uses the LHA and LHAU instructions. Those instructions basically do a load, but also sign extend the result. Since we need to fill our registers by hand when doing MMIO, we also need to sign extend manually. This patch implements sign extended MMIO and the LHA(U) instructions. Signed-off-by: NAlexander Graf <agraf@suse.de> Signed-off-by: NAvi Kivity <avi@redhat.com>
-
由 Alexander Graf 提交于
Modern PowerPCs have a 64 bit wide FPSCR register. Let's accomodate for that and make it 64 bits in our vcpu struct too. Signed-off-by: NAlexander Graf <agraf@suse.de> Signed-off-by: NAvi Kivity <avi@redhat.com>
-
由 Alexander Graf 提交于
The Gekko has GPRs, SPRs and FPRs like normal PowerPC codes, but it also has QPRs which are basically single precision only FPU registers that get used when in paired single mode. The following patches depend on them being around, so let's add the definitions early. Signed-off-by: NAlexander Graf <agraf@suse.de> Signed-off-by: NAvi Kivity <avi@redhat.com>
-