[ Upstream commit 94fe5f2b45c4108885e4b71f6b181068632ec904 ]

Register slimbus controller only after finishing powerup sequnce so that we
do not endup in situation where core starts sending transactions before
the controller is ready.
Signed-off-by: NSrinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: NSasha Levin <sashal@kernel.org>

[ Upstream commit 9652e6aa62a1836494ebb8dbd402587c083b568c ]

It looks like there is a typo in probe return. Fix it.
Signed-off-by: NSrinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: NSasha Levin <sashal@kernel.org>

[ Upstream commit 1830dad34c070161fda2ff1db77b39ffa78aa380 ]

Move ngd platform driver out of loop so that it registers only once.
Signed-off-by: NSrinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: NSasha Levin <sashal@kernel.org>

[ Upstream commit 30af4fb619e5126cb3152072e687b377fc9398d6 ]

When a replicator port is enabled, we block the traffic
on the other port and route all traffic to the new enabled
port. If there are two active trace sessions each targeting
the two different paths from the replicator, the second session
will disable the first session and route all the data to the
second path.
                    ETR
                 /
e.g, replicator
                 \
                    ETB

If CPU0 is operated in sysfs mode to ETR and CPU1 is operated
in perf mode to ETB, depending on the order in which the
replicator is enabled one device is blocked.

Ideally we need trace-id for the session to make the
right choice. That implies we need a trace-id allocation
logic for the coresight subsystem and use that to route
the traffic. The short term solution is to only manage
the "target port" and leave the other port untouched.
That leaves both the paths unaffected, except that some
unwanted traffic may be pushed to the paths (if the Trace-IDs
are not far enough), which is still fine and can be filtered
out while processing rather than silently blocking the data.

Cc: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: NSuzuki K Poulose <suzuki.poulose@arm.com>
Signed-off-by: NMathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: NSasha Levin <sashal@kernel.org>

[ Upstream commit e7753f3937610633a540f2be81be87531f96ff04 ]

>From the comment in the code, it claims the requirement for byte-address
alignment for RRP register: 'for 32-bit, 64-bit and 128-bit wide trace
memory, the four LSBs must be 0s. For 256-bit wide trace memory, the
five LSBs must be 0s'.  This isn't consistent with the program, the
program sets five LSBs as zeros for 32/64/128-bit wide trace memory and
set six LSBs zeros for 256-bit wide trace memory.

After checking with the CoreSight Trace Memory Controller technical
reference manual (ARM DDI 0461B, section 3.3.4 RAM Read Pointer
Register), it proves the comment is right and the program does wrong
setting.

This patch fixes byte-address alignment for RRP by following correct
definition in the technical reference manual.

Cc: Mathieu Poirier <mathieu.poirier@linaro.org>
Cc: Mike Leach <mike.leach@linaro.org>
Signed-off-by: NLeo Yan <leo.yan@linaro.org>
Signed-off-by: NMathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: NSasha Levin <sashal@kernel.org>

[ Upstream commit b860801e3237ec4c74cf8de0be4816996757ae5c ]

For non-VHE systems host kernel runs at EL1 and jumps to EL2 whenever
hypervisor code should be executed. In this case ETM4x driver must
restrict configuration to EL1 when it setups kernel tracing.
However, there is no separate hypervisor privilege level when VHE
is enabled, the host kernel runs at EL2.

This patch fixes configuration of TRCACATRn register for VHE systems
so that ETM_EXLEVEL_NS_HYP bit is used instead of ETM_EXLEVEL_NS_OS
to on/off kernel tracing. At the same time, it moves common code
to new helper.
Signed-off-by: NTomasz Nowicki <tnowicki@caviumnetworks.com>
Signed-off-by: NMathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: NSasha Levin <sashal@kernel.org>

[ Upstream commit 96a7f644006ecc05eaaa1a5d09373d0ee63beb0a ]

Since the ETR could be driven either by SYSFS or by perf, it
becomes complicated how we deal with the buffers used for each
of these modes. The ETR driver cannot simply free the current
attached buffer without knowing the provider (i.e, sysfs vs perf).

To solve this issue, we provide:
1) the driver-mode specific etr buffer to be retained in the drvdata
2) the etr_buf for a session should be passed on when enabling the
   hardware, which will be stored in drvdata->etr_buf. This will be
   replaced (not free'd) as soon as the hardware is disabled, after
   necessary sync operation.

The advantages of this are :

1) The common code path doesn't need to worry about how to dispose
   an existing buffer, if it is about to start a new session with a
   different buffer, possibly in a different mode.
2) The driver mode can control its buffers and can get access to the
   saved session even when the hardware is operating in a different
   mode. (e.g, we can still access a trace buffer from a sysfs mode
   even if the etr is now used in perf mode, without disrupting the
   current session.)

Towards this, we introduce a sysfs specific data which will hold the
etr_buf used for sysfs mode of operation, controlled solely by the
sysfs mode handling code.

Cc: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: NSuzuki K Poulose <suzuki.poulose@arm.com>
Signed-off-by: NMathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: NSasha Levin <sashal@kernel.org>

[ Upstream commit 4f8ef21007531c3d7cb5b826e7b2c8999b65ecae ]

We enable the trace path, before activating the source.
If we fail to enable the source, we must disable the path
to make sure it is available for another session.

Cc: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: NSuzuki K Poulose <suzuki.poulose@arm.com>
Signed-off-by: NMathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: NSasha Levin <sashal@kernel.org>

[ Upstream commit 5ecabe4a76e8cdb61fa3e24862d9ca240a1c4ddf ]

We create a coresight trace path for each online CPU when
we start the event. We rely on the number of online CPUs
and then go on to allocate an array matching the "number of
online CPUs" for holding the path and then uses normal
CPU id as the index to the array. This is problematic as
we could have some offline CPUs causing us to access beyond
the actual array size (e.g, on a dual SMP system, if CPU0 is
offline, CPU1 could be really accessing beyond the array).
The solution is to switch to per-cpu array for holding the path.

Cc: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: NSuzuki K Poulose <suzuki.poulose@arm.com>
Signed-off-by: NMathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: NSasha Levin <sashal@kernel.org>

[ Upstream commit c71369de02b285d9da526a526d8f2affc7b17c59 ]

The coresight components could be operated either in sysfs mode or in perf
mode. For some of the components, the mode of operation doesn't matter as
they simply relay the data to the next component in the trace path. But for
sinks, they need to be able to provide the trace data back to the user.
Thus we need to make sure that "mode" is handled appropriately. e.g,
the sysfs mode could have multiple sources driving the trace data, while
perf mode doesn't allow sharing the sink.

The coresight_enable_sink() however doesn't really allow this check to
trigger as it skips the "enable_sink" callback if the component is
already enabled, irrespective of the mode. This could cause mixing
of data from different modes or even same mode (in perf), if the
sources are different. Also, if we fail to enable the sink while
enabling a path (where sink is the first component enabled),
we could end up in disabling the components in the "entire"
path which were not enabled in this trial, causing disruptions
in the existing trace paths.

Cc: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: NSuzuki K Poulose <suzuki.poulose@arm.com>
Signed-off-by: NMathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: NSasha Levin <sashal@kernel.org>

[ Upstream commit bbd35ba6fab5419e58e96f35f1431f13bdc14f98 ]

Use ERR_CAT inlined function to replace the ERR_PTR(PTR_ERR). It
make the code more concise.
Signed-off-by: Nzhong jiang <zhongjiang@huawei.com>
Signed-off-by: NMathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: NSasha Levin <sashal@kernel.org>

[ Upstream commit 8dbf9c7abefd5c1434a956d5c6b25e11183061a3 ]

When USB requests for video data fail to be submitted, the driver
signals a problem to the host by halting the video streaming endpoint.
This is only valid in bulk mode, as isochronous transfers have no
handshake phase and can't thus report a stall. The usb_ep_set_halt()
call returns an error when using isochronous endpoints, which we happily
ignore, but some UDCs complain in the kernel log. Fix this by only
trying to halt the endpoint in bulk mode.
Signed-off-by: NLaurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: NPaul Elder <paul.elder@ideasonboard.com>
Tested-by: NPaul Elder <paul.elder@ideasonboard.com>
Reviewed-by: NKieran Bingham <kieran.bingham@ideasonboard.com>
Signed-off-by: NSasha Levin <sashal@kernel.org>

[ Upstream commit 9d1ff5dcb3cd3390b1e56f1c24ae42c72257c4a3 ]

USB requests for video data are queued from two different locations in
the driver, with the same code block occurring twice. Factor it out to a
function.
Signed-off-by: NLaurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: NPaul Elder <paul.elder@ideasonboard.com>
Tested-by: NPaul Elder <paul.elder@ideasonboard.com>
Reviewed-by: NKieran Bingham <kieran.bingham@ideasonboard.com>
Signed-off-by: NSasha Levin <sashal@kernel.org>

[ Upstream commit 245f880c25dbd8927af0f33aa5d1404370013957 ]

Update VDD_SOC voltage to 1.25V for 900MHz operating point
according to datasheet Rev. 1.3, 08/2018, 25mV is added to
the minimum allowed values to cover power supply ripple.
Signed-off-by: NAnson Huang <Anson.Huang@nxp.com>
Reviewed-by: NSébastien Szymanski <sebastien.szymanski@armadeus.com>
Signed-off-by: NShawn Guo <shawnguo@kernel.org>
Signed-off-by: NSasha Levin <sashal@kernel.org>

[ Upstream commit 6c7103aa026094a4ee2c2708ec6977a6dfc5331d ]

When runtime is not enabled, pm_runtime_get_sync() returns -EACCESS,
the counter will be incremented but the resume callback not called,
so enumeration and charging will not start properly.
To avoid that happen, disable irq on suspend and recheck on resume.

Practically this happens when the device is woken up from suspend by
plugging in usb.
Signed-off-by: NAndreas Kemnade <andreas@kemnade.info>
Signed-off-by: NKishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: NSasha Levin <sashal@kernel.org>

[ Upstream commit 09938ea9d136243e8d1fed6d4d7a257764f28f6d ]

This patch fixes and issue that the vbus_ctrl is disabled by
rcar_gen3_init_from_a_peri_to_a_host(), so a usb host cannot
supply the vbus.

Note that this condition will exit when the otg irq happens
even if we don't apply this patch.

Fixes: 9bb86777 ("phy: rcar-gen3-usb2: add sysfs for usb role swap")
Signed-off-by: NYoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Reviewed-by: NSimon Horman <horms+renesas@verge.net.au>
Signed-off-by: NKishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: NSasha Levin <sashal@kernel.org>

[ Upstream commit 26728df4b254ae06247726a9a6e64823e39ac504 ]

Broadcom ARM-based DSL SoCs (BCM63xx product line) have the same
Broadcom SATA PHY that other SoCs are using, make it possible to select
that driver on these platforms.
Signed-off-by: NFlorian Fainelli <f.fainelli@gmail.com>
Signed-off-by: NKishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: NSasha Levin <sashal@kernel.org>

[ Upstream commit 95590a6286c547b7287d01c55515fb96b904aa03 ]

of_find_device_by_node takes a reference to the struct device when it
finds a match via get_device. but it fails to put_device in
at91_pm_config_ws, for_each_matching_node_and_match will get and put
the node properly, there is no need to call the of_put_node. Therefore,
just call put_device instead of of_node_put in at91_pm_config_ws.

Fixes: d7484f5c ("ARM: at91: pm: configure wakeup sources for ULP1 mode")
Suggested-by: NClaudiu Beznea <Claudiu.Beznea@microchip.com>
Signed-off-by: Nzhong jiang <zhongjiang@huawei.com>
Signed-off-by: NAlexandre Belloni <alexandre.belloni@bootlin.com>
Signed-off-by: NSasha Levin <sashal@kernel.org>

[ Upstream commit ae9847f48a4b4bff0335da20be63ac84d94eb54c ]

GPIOs with no programmable direction are not required to implement
direction_output nor direction_input.

If we try to set an output direction on an output-only GPIO or input
direction on an input-only GPIO simply return 0.

This allows this single direction GPIO to be used by libgpiod.
Signed-off-by: NRicardo Ribalda Delgado <ricardo.ribalda@gmail.com>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>
Signed-off-by: NSasha Levin <sashal@kernel.org>

[ Upstream commit 17ccba67109cd0631f206cf49e17986218b47854 ]

The function that computes clock parameters from divisors did not
respect the maximum size of the bitfields that the parameters were
written to. This fixes the bug.

This bug can be reproduced with (and this fix verified with) the test
at: https://kunit-review.googlesource.com/c/linux/+/1035/

Discovered-by-KUnit: https://kunit-review.googlesource.com/c/linux/+/1035/Signed-off-by: NBrendan Higgins <brendanhiggins@google.com>
Reviewed-by: NJae Hyun Yoo <jae.hyun.yoo@linux.intel.com>
Signed-off-by: NWolfram Sang <wsa@the-dreams.de>
Signed-off-by: NSasha Levin <sashal@kernel.org>

[ Upstream commit ff1e37c6809daab75f7b2dea1efe69330e8eb65b ]

The proper parent clock for audio subsystem for Exynos5420 and Exynos5800
SoCs is CLK_MAU_EPLL. This fixes following warning:

    clk: failed to reparent mout_audss to fout_epll: -22

Fixes: ed7d1307: ARM: dts: exynos: Enable HDMI audio support on Peach Pit
Fixes: bae0f445: ARM: dts: exynos: Enable HDMI audio support on Peach Pi
Signed-off-by: NMarek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: NKrzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: NSasha Levin <sashal@kernel.org>

[ Upstream commit 89969a842e72b1b653140a4bbddd927b242736d0 ]

There is an issue where the host is unable to tell the gadget what frame
rate it wants if the dwFrameIntervals in the interface descriptors are
not in ascending order. This means that when instantiating a uvc gadget
via configfs the user must make sure the dwFrameIntervals are in
ascending order.

Instead of silently failing the breaking of this rule, we sort the
dwFrameIntervals upon writing to configfs.
Signed-off-by: NPaul Elder <paul.elder@ideasonboard.com>
Reviewed-by: NLaurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: NSasha Levin <sashal@kernel.org>

[ Upstream commit cb2200f7af8341aaf0c6abd7ba37e4c667c41639 ]

While checks are in place to avoid attributes and children of a format
being manipulated after the format is linked into the streaming header,
the linked flag was never actually set, invalidating the protections.
Update the flag as appropriate in the header link calls.
Signed-off-by: NJoel Pepper <joel.pepper@rwth-aachen.de>
Reviewed-by: NKieran Bingham <kieran.bingham@ideasonboard.com>
Signed-off-by: NLaurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: NSasha Levin <sashal@kernel.org>

[ Upstream commit 86f3daed59bceb4fa7981d85e89f63ebbae1d561 ]

Some of the .allow_link() and .drop_link() operations implementations
call config_group_find_item() and then leak the reference to the
returned item. Fix this by dropping those references where needed.
Signed-off-by: NLaurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: NKieran Bingham <kieran.bingham@ideasonboard.com>
Signed-off-by: NSasha Levin <sashal@kernel.org>

[ Upstream commit a2df0984e73fd9e1dad5fc3f1c307ec3de395e30 ]

It is good practice to make the setting of gpio-pinctrls explicitly in the
devicetree, and in this case even necessary.
Rockchip boards start with iomux settings set to gpio for most pins and
while the linux pinctrl driver also implicitly sets the gpio function if
a pin is requested as gpio that is not necessarily true for other drivers.

The issue in question stems from uboot, where the sdmmc_pwr pin is set
to function 1 (sdmmc-power) by the bootrom when reading the 1st-stage
loader. The regulator controlled by the pin is active-low though, so
when the dwmmc hw-block sets its enabled bit, it actually disables the
regulator. By changing the pin back to gpio we fix that behaviour.
Signed-off-by: NHeiko Stuebner <heiko@sntech.de>
Signed-off-by: NSasha Levin <sashal@kernel.org>

[ Upstream commit 4158757395b300b6eb308fc20b96d1d231484413 ]

Clang warns when one enumerated type is implicitly converted to another.

drivers/media/platform/davinci/vpbe_display.c:524:24: warning: implicit
conversion from enumeration type 'enum osd_v_exp_ratio' to different
enumeration type 'enum osd_h_exp_ratio' [-Wenum-conversion]
                        layer_info->h_exp = V_EXP_6_OVER_5;
                                          ~ ^~~~~~~~~~~~~~
1 warning generated.

This appears to be a copy and paste error judging from the couple of
lines directly above this statement and the way that height is handled
in the if block above this one.
Reported-by: NNick Desaulniers <ndesaulniers@google.com>
Signed-off-by: NNathan Chancellor <natechancellor@gmail.com>
Signed-off-by: NHans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab+samsung@kernel.org>
Signed-off-by: NSasha Levin <sashal@kernel.org>

[ Upstream commit f347596f2bf114a3af3d80201c6e6bef538d884f ]

Correcting red herring error messages.

Where appropriate, replaces au0282_dev_register with:
- au0828_analog_register
- au0828_dvb_register
Signed-off-by: NBrad Love <brad@nextdimension.cc>
Signed-off-by: NHans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab+samsung@kernel.org>
Signed-off-by: NSasha Levin <sashal@kernel.org>

[ Upstream commit 8d11eb847de7d89c2754988c944d51a4f63e219b ]

The driver may sleep in a interrupt handler.

The function call paths (from bottom to top) in Linux-4.16 are:

[FUNC] kzalloc(GFP_KERNEL)
drivers/media/pci/ivtv/ivtv-yuv.c, 938:
	kzalloc in ivtv_yuv_init
drivers/media/pci/ivtv/ivtv-yuv.c, 960:
	ivtv_yuv_init in ivtv_yuv_next_free
drivers/media/pci/ivtv/ivtv-yuv.c, 1126:
	ivtv_yuv_next_free in ivtv_yuv_setup_stream_frame
drivers/media/pci/ivtv/ivtv-irq.c, 827:
	ivtv_yuv_setup_stream_frame in ivtv_irq_dec_data_req
drivers/media/pci/ivtv/ivtv-irq.c, 1013:
	ivtv_irq_dec_data_req in ivtv_irq_handler

To fix this bug, GFP_KERNEL is replaced with GFP_ATOMIC.

This bug is found by my static analysis tool DSAC.
Signed-off-by: NJia-Ju Bai <baijiaju1990@gmail.com>
Signed-off-by: NHans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab+samsung@kernel.org>
Signed-off-by: NSasha Levin <sashal@kernel.org>

[ Upstream commit 8d1a4817cce1b15b4909f0e324a4f5af5952da67 ]

A warning that I thought to be solved by a previous patch of mine
has resurfaced with gcc-8:

media/imx/imx-media-csi.c: In function 'csi_link_validate':
media/imx/imx-media-csi.c:1025:20: error: 'upstream_ep' may be used uninitialized in this function [-Werror=maybe-uninitialized]
media/imx/imx-media-csi.c:1026:24: error: 'upstream_ep.bus_type' may be used uninitialized in this function [-Werror=maybe-uninitialized]
media/imx/imx-media-csi.c:127:19: error: 'upstream_ep.bus.parallel.bus_width' may be used uninitialized in this function [-Werror=maybe-uninitialized]
media/imx/imx-media-csi.c: In function 'csi_enum_mbus_code':
media/imx/imx-media-csi.c:132:9: error: '*((void *)&upstream_ep+12)' may be used uninitialized in this function [-Werror=maybe-uninitialized]
media/imx/imx-media-csi.c:132:48: error: 'upstream_ep.bus.parallel.bus_width' may be used uninitialized in this function [-Werror=maybe-uninitialized]

I spent some more time digging in this time, and think I have a better
fix, bailing out of the function that either initializes or errors
out here, which simplifies the code enough for gcc to figure out
what is going on. The earlier partial workaround can be removed now,
as the new workaround is better.

Fixes: 890f2769 ("media: imx: work around false-positive warning")
Signed-off-by: NArnd Bergmann <arnd@arndb.de>
Signed-off-by: NHans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab+samsung@kernel.org>
Signed-off-by: NSasha Levin <sashal@kernel.org>

[ Upstream commit 12ba7e1045521ec9f251c93ae0a6735cc3f42337 ]

Up until now, mlxsw tolerated firmware versions that weren't exactly
matching the required version, if the branch number matched. That
allowed the users to test various firmware versions as long as they were
on the right branch.

On the other hand, it made it impossible for mlxsw to put a hard lower
bound on a version that fixes all problems known to date. If a user had
a somewhat older FW version installed, mlxsw would start up just fine,
possibly performing non-optimally as it would use features that trigger
problematic behavior.

Therefore tweak the check to accept any FW version that is:

- on the same branch as the preferred version, and
- the same as or newer than the preferred version.
Signed-off-by: NPetr Machata <petrm@mellanox.com>
Reviewed-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NIdo Schimmel <idosch@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>
Signed-off-by: NSasha Levin <sashal@kernel.org>

[ Upstream commit 88a20edf76091ee7f1bb459b89d714d53f0f8940 ]

The microSD card slot in the Sapphire board is not working because of
several issues:
 1.- The vmmc power supply is missing in the DTS. It is capable of 3.0V
 and has a GPIO-based enable control.
 2.- The vqmmc power supply can provide up to 3.3V, but it is capped in
 the DTS to just 3.0V because of the vmmc capability. This results in a
 conflict from the mmc driver requesting an unsupportable voltage range
 from 3.3V to 3.0V (min > max) as reported in dmesg. So, extend the
 range up to 3.3V. The hw should be able to stand this 0.3V tolerance.
 See mmc_regulator_set_vqmmc in drivers/mmc/core/core.c.
 3.- The card detect signal is non-working. There is a known conflict
 with jtag, but the workaround in drivers/soc/rockchip/grf.c does not
 work. Adding the broken-cd attribute to the DTS fixes the issue.
Signed-off-by: NVicente Bergas <vicencb@gmail.com>
Signed-off-by: NHeiko Stuebner <heiko@sntech.de>
Signed-off-by: NSasha Levin <sashal@kernel.org>

[ Upstream commit a6da4d6fdf8bd512c98d3ac7f1d16bc4bb282919 ]

We can rely on the system kernel and the dump capture kernel themselves in
memory usage.

Being restrictive with 512MB limit may cause kexec tool failure on some
platforms.
Tested-by: NRachel Mozes <rachel.mozes@intel.com>
Reported-by: NRachel Mozes <rachel.mozes@intel.com>
Signed-off-by: NDengcheng Zhu <dzhu@wavecomp.com>
Signed-off-by: NPaul Burton <paul.burton@mips.com>
Patchwork: https://patchwork.linux-mips.org/patch/20568/
Cc: pburton@wavecomp.com
Cc: ralf@linux-mips.org
Cc: linux-mips@linux-mips.org
Signed-off-by: NSasha Levin <sashal@kernel.org>

[ Upstream commit 6f6da136046294a1e8d2944336eb97412751f653 ]

The {i3200|i7core|sb|skx}_edac drivers show DIMM capacity using the
wrong unit symbol: 'Mb' - megabit. Fix them by replacing 'Mb' with
'MiB' - mebibyte.

[Tony: These are all "edac_dbg()" messages, so this won't break scripts
       that parse console logs.]
Signed-off-by: NQiuxu Zhuo <qiuxu.zhuo@intel.com>
Signed-off-by: NTony Luck <tony.luck@intel.com>
Signed-off-by: NBorislav Petkov <bp@suse.de>
Acked-by: NAristeu Rozanski <aris@redhat.com>
Cc: Mauro Carvalho Chehab <mchehab@kernel.org>
Cc: linux-edac@vger.kernel.org
Link: https://lkml.kernel.org/r/20180919003433.16475-1-tony.luck@intel.comSigned-off-by: NSasha Levin <sashal@kernel.org>

[ Upstream commit 2893cc8ff892fa74972d8dc0e1d0dc65116daaa3 ]

Presently we check first if CPUID is enabled. If it is not already
enabled, then we next call identify_cpu_without_cpuid() and clear
X86_FEATURE_CPUID.

Unfortunately, identify_cpu_without_cpuid() is the function where CPUID
becomes _enabled_ on Cyrix 6x86/6x86L CPUs.

Reverse the calling sequence so that CPUID is first enabled, and then
check a second time to see if the feature has now been activated.

[ bp: Massage commit message and remove trailing whitespace. ]
Suggested-by: NAndy Lutomirski <luto@amacapital.net>
Signed-off-by: NMatthew Whitehead <tedheadster@gmail.com>
Signed-off-by: NBorislav Petkov <bp@suse.de>
Reviewed-by: NAndy Lutomirski <luto@amacapital.net>
Cc: David Woodhouse <dwmw@amazon.co.uk>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Link: http://lkml.kernel.org/r/20180921212041.13096-3-tedheadster@gmail.comSigned-off-by: NSasha Levin <sashal@kernel.org>

[ Upstream commit 03b099bdcdf7125d4a63dc9ddeefdd454e05123d ]

There are comments in processor-cyrix.h advising you to _not_ make calls
using the deprecated macros in this style:

  setCx86_old(CX86_CCR4, getCx86_old(CX86_CCR4) | 0x80);

This is because it expands the macro into a non-functioning calling
sequence. The calling order must be:

  outb(CX86_CCR2, 0x22);
  inb(0x23);

From the comments:

 * When using the old macros a line like
 *   setCx86(CX86_CCR2, getCx86(CX86_CCR2) | 0x88);
 * gets expanded to:
 *  do {
 *    outb((CX86_CCR2), 0x22);
 *    outb((({
 *        outb((CX86_CCR2), 0x22);
 *        inb(0x23);
 *    }) | 0x88), 0x23);
 *  } while (0);

The new macros fix this problem, so use them instead.
Signed-off-by: NMatthew Whitehead <tedheadster@gmail.com>
Signed-off-by: NBorislav Petkov <bp@suse.de>
Reviewed-by: NAndy Lutomirski <luto@amacapital.net>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: Jia Zhang <qianyue.zj@alibaba-inc.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Philippe Ombredanne <pombredanne@nexb.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Link: http://lkml.kernel.org/r/20180921212041.13096-2-tedheadster@gmail.comSigned-off-by: NSasha Levin <sashal@kernel.org>

[ Upstream commit 06983aa526c759ebdf43f202d8d0491d9494e2f4 ]

The method ndo_start_xmit() is defined as returning an 'netdev_tx_t',
which is a typedef for an enum type, so make sure the implementation in
this driver has returns 'netdev_tx_t' value, and change the function
return type to netdev_tx_t.

Found by coccinelle.
Signed-off-by: NYueHaibing <yuehaibing@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>
Signed-off-by: NSasha Levin <sashal@kernel.org>

[ Upstream commit 2b49117a5abee8478b0470cba46ac74f93b4a479 ]

The method ndo_start_xmit() is defined as returning an 'netdev_tx_t',
which is a typedef for an enum type, so make sure the implementation in
this driver has returns 'netdev_tx_t' value, and change the function
return type to netdev_tx_t.

Found by coccinelle.
Signed-off-by: NYueHaibing <yuehaibing@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>
Signed-off-by: NSasha Levin <sashal@kernel.org>

[ Upstream commit b78ac6ecd1b6b46f8767cbafa95a7b0b51b87ad8 ]

Allow the configuration of the MDIO clock divider when the Device Tree
contains 'clock-frequency' property (similar to I2C and SPI buses).
Because the hardware may have lost its state during suspend/resume,
re-apply the MDIO clock divider upon resumption.
Signed-off-by: NFlorian Fainelli <f.fainelli@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>
Signed-off-by: NSasha Levin <sashal@kernel.org>

[ Upstream commit 32c009798385ce21080beaa87a9b95faad3acd1e ]

following commit:
commit d58e468b1112 ("flow_dissector: implements flow dissector BPF hook")
added struct bpf_flow_keys which conflicts with the struct with
same name in sockex2_kern.c and sockex3_kern.c

similar to commit:
commit 534e0e52bc23 ("samples/bpf: fix a compilation failure")
we tried the rename it "flow_keys" but it also conflicted with struct
having same name in include/net/flow_dissector.h. Hence renaming the
struct to "flow_key_record". Also, this commit doesn't fix the
compilation error completely because the similar struct is present in
sockex3_kern.c. Hence renaming it in both files sockex3_user.c and
sockex3_kern.c
Signed-off-by: NPrashant Bhole <bhole_prashant_q7@lab.ntt.co.jp>
Acked-by: NSong Liu <songliubraving@fb.com>
Signed-off-by: NDaniel Borkmann <daniel@iogearbox.net>
Signed-off-by: NSasha Levin <sashal@kernel.org>

[ Upstream commit c4eed62a214330908eec11b0dc170d34fa50b412 ]

The secondary bus reset may have link side effects that a hotplug capable
port may incorrectly react to.  Use the slot specific reset for hotplug
ports, fixing the undesirable link down-up handling during error
recovering.
Signed-off-by: NKeith Busch <keith.busch@intel.com>
[bhelgaas: fold in
https://lore.kernel.org/linux-pci/20180926152326.14821-1-keith.busch@intel.com
for issue reported by Stephen Rothwell <sfr@canb.auug.org.au>]
Signed-off-by: NBjorn Helgaas <bhelgaas@google.com>
Reviewed-by: NSinan Kaya <okaya@kernel.org>
Signed-off-by: NSasha Levin <sashal@kernel.org>