- 22 4月, 2005 31 次提交
-
-
由 Michael Chan 提交于
Add MSI support for 5751 C0 and 5752. Signed-off-by: NMichael Chan <mchan@broadcom.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Michael Chan 提交于
Fix a bug in tg3_set_eeprom() when the length is less than 4 and the offset is not 4-byte aligned. Signed-off-by: NMichael Chan <mchan@broadcom.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Michael Chan 提交于
Add support for the NVRAM lock-out feature for TPM in 5752. If lock-out is enabled, certain NVRAM registers cannot be written to. Signed-off-by: NMichael Chan <mchan@broadcom.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Michael Chan 提交于
Signed-off-by: NMichael Chan <mchan@broadcom.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Michael Chan 提交于
Add bit definitions for the new GPIO3 in 5752. GPIO3 must be driven as output when it is unused. Signed-off-by: NMichael Chan <mchan@broadcom.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Michael Chan 提交于
The 5752 A0 chip ID is wrong in hardware. The simplest way to workaround it is to change it to the correct value in tp->pci_chip_rev_id. This way, it is easier to check for the ASIC_REV_5752 in the rest of the driver. Signed-off-by: NMichael Chan <mchan@broadcom.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Michael Chan 提交于
Fix tg3_set_power_state to drive GPIOs properly based on the TG3_FLAG_EEPROM_WRITE_PROTECT flag. Some delays are also added after D0 and D3 power state changes. Signed-off-by: NMichael Chan <mchan@broadcom.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Michael Chan 提交于
Setup proper GPIO settings in tp->grc_local_ctrl before calling tg3_set_power() state in tg3_get_invariants() and after chip reset. Signed-off-by: NMichael Chan <mchan@broadcom.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Michael Chan 提交于
Split the 1st half of tg3_phy_probe() into tg3_get_eeprom_hw_cfg() so that the TG3_FLAG_EEPROM_WRITE_PROT can be determined before calling tg3_set_power_state() in tg3_get_invariants(). This will allow tg3_set_power_state() to drive the GPIOs correctly based on the config. information in eeprom. On the 5752, there are no pull-up resistors on the GPIO pins and it is necessary to drive the unused GPIOs as output. Signed-off-by: NMichael Chan <mchan@broadcom.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Michael Chan 提交于
Some minor 5752 fixes mostly for correctness and add 5752 PHY ID. Signed-off-by: NMichael Chan <mchan@broadcom.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 John W. Linville 提交于
Replace existing ASIC_REV_5752 definition with ASIC_REV_5752_A0, and add definition for ASIC_REV_5752_A1. Then, add ASIC_REV_5752_A1 to check for setting TG3_FLG2_5750_PLUS in tg3_get_invariants. Signed-off-by: NJohn W. Linville <linville@tuxdriver.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 John W. Linville 提交于
Use check of TG3_FLG2_5750_PLUS in tg3_get_invariants to set TG3_FLG2_5705_PLUS flag. Signed-off-by: NJohn W. Linville <linville@tuxdriver.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 John W. Linville 提交于
Rewrite checks in tg3_get_invariants to use TG3_FLG2_5705_PLUS and TG3_FLG2_5750_PLUS flags. Signed-off-by: NJohn W. Linville <linville@tuxdriver.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 John W. Linville 提交于
Rewrite of a couple of troublesome multi-way if statements to use TG3_FLG2_5705_PLUS flag. Signed-off-by: NJohn W. Linville <linville@tuxdriver.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 John W. Linville 提交于
Replace a number of two-way if statements checking for 5750, and/or 5752 to reference the newly-defined TG3_FLG2_5750_PLUS flag instead. Signed-off-by: NJohn W. Linville <linville@tuxdriver.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 John W. Linville 提交于
Define TG3_FLG2_5750_PLUS flag and set it in tg3_get_invariants for ASIC_REV_5750 or ASIC_REV_5752. Signed-off-by: NJohn W. Linville <linville@tuxdriver.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 John W. Linville 提交于
Replace a number of three-way if statements checking for 5705, 5750, and 5752 to reference the equivalent TG3_FLG2_5705_PLUS flag instead. Signed-off-by: NJohn W. Linville <linville@tuxdriver.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 John W. Linville 提交于
Add proper entry for bcm5752 PCI ID to pci_ids.h, and use it in tg3. I did this separately in case patches like this (i.e. new PCI IDs) need to come from more "official" sources. Signed-off-by: NJohn W. Linville <linville@tuxdriver.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 John W. Linville 提交于
Add hard-coded definition of bcm5752 PCI ID to tg3_pci_tbl. Next patch will change entry to use pci_ids.h-based definition. Signed-off-by: NJohn W. Linville <linville@tuxdriver.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 John W. Linville 提交于
Add ASIC_REV_5752 definition. Track-down all references to ASIC_REV_5750 and mirror them with references to the newly defined ASIC_REV_5752. Signed-off-by: NJohn W. Linville <linville@tuxdriver.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Adrian Bunk 提交于
Signed-off-by: NAdrian Bunk <bunk@stusta.de> Signed-off-by: NChas Williams <chas@cmf.nrl.navy.mil> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Arnaldo Carvalho de Melo 提交于
I.e. not using skb->dev as a way to pass the parameter used to fill... skb->dev :-) Also to get the _type_trans open coded sequence grouped, next changesets will introduce ax25_type_trans. Signed-off-by: NRalf Baechle <ralf@linux-mips.org> Signed-off-by: NArnaldo Carvalho de Melo <acme@ghostprotocols.net> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Chas Williams 提交于
Signed-off-by: NChas Williams <chas@cmf.nrl.navy.mil> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Patrick McHardy 提交于
While we're at it, lets also replace KERN_INFO by KERN_EMERG to make sure the user gets to see it. Signed-off-by: NPatrick McHardy <kaber@trash.net> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 James Bottomley 提交于
The patch to arch/i386/kernel/cpu/amd.c relies on the variable cpu_core_id which is defined in i386/kernel/smpboot.c. This means it is only present if CONFIG_X86_SMP is defined, not CONFIG_SMP (alternative SMP harnesses won't have it, which is why it breaks voyager). Signed-off-by: NJames Bottomley <James.Bottomley@SteelEye.com> Signed-off-by: NLinus Torvalds <torvalds@osdl.org>
-
由 Adrian Bunk 提交于
The untested patch below should fix this compile error. Signed-off-by: NAdrian Bunk <bunk@stusta.de> Signed-off-by: NLinus Torvalds <torvalds@osdl.org>
-
由 Jody McIntyre 提交于
Fix non-legacy multichannel ISO receive, broken by Parag Wardukar's allocation fix. Multichannel ISO receive still sucks; it should be possible to use both legacy and non-legacy modes at the same time, but with this patch, things are no worse than they were in 2.6.11 and allocation is still done at the correct time. Signed-off-by: NJody McIntyre <scjody@steamballoon.com> Signed-off-by: NLinus Torvalds <torvalds@osdl.org>
-
由 Jody McIntyre 提交于
- Print the correct value in the DBGMSG in dma_rcv_tasklet(). See OHCI 1.1 section 8.7, page 103 ff. - Print tlabels as %d everywhere. Signed-off-by: NStefan Richter <stefanr@s5r6.in-berlin.de> Signed-off-by: NJody McIntyre <scjody@steamballoon.com> Signed-off-by: NLinus Torvalds <torvalds@osdl.org>
-
由 Richard Henderson 提交于
Allocate syscall numbers for add_key, request_key, keyctl.
-
由 David Mosberger-Tang 提交于
The ia64-version of fls() never worked as intended (the bitnumbering was off by 1 and fls(0) was undefined). This patch fixes the problem by using a popcnt-based fls(), which on McKinley-derived cores is slightly faster than both ia64_fls() and generic_fls(). The resulting code, however, is bigger (7-8 bundles instead of about 3 bundles). Also switch ia64_popcnt() to __builtin_popcountl() for GCC v3.4 or newer since the compiler can predicate that and schedule it better. Thanks to Simon Derr and Matt Mackall for tracking down this bug. Signed-off-by: NDavid Mosberger-Tang <davidm@hpl.hp.com> Signed-off-by: NTony Luck <tony.luck@intel.com>
-
- 21 4月, 2005 6 次提交
-
-
由 Karsten Keil 提交于
We do not longer use DLT_LINUX_SLL for activ/pass filters but DLT_PPP_WITHDIRECTION witch need 1 as outbound flag. Signed-off-by: NKarsten Keil <kkeil@suse.de> Signed-off-by: NLinus Torvalds <torvalds@osdl.org>
-
由 Alexander Nyberg 提交于
The new out of line put_user() assembly on x86_64 changes %rcx without telling GCC about it causing things like: http://bugme.osdl.org/show_bug.cgi?id=4515 See to it that %rcx is not changed (made it consistent with get_user()). Signed-off-by: NAlexander Nyberg <alexn@telia.com> Signed-off-by: ak@suse.de Signed-off-by: NLinus Torvalds <torvalds@osdl.org>
-
由 James Bottomley 提交于
My version of gcc doesn't warn about this error (declaration in the middle of a set of statements). The fix is simple (this also corrects return code; for init functions it should be zero or error).
-
由 Al Viro 提交于
PREEMPT+SMP support - see if it looks sane... Signed-off-by: NAl Viro <viro@parcelfarce.linux.theplanet.co.uk> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Linus Torvalds 提交于
Releasing this will also make "git" the official source control thing. Here's to hoping for the best.
-
- 20 4月, 2005 3 次提交
-
-
由 Herbert Xu 提交于
The following patch just makes the header part of the skb writeable. This is needed since we modify the IP headers just a few lines below. Signed-off-by: NHerbert Xu <herbert@gondor.apana.org.au> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Herbert Xu 提交于
Signed-off-by: NHerbert Xu <herbert@gondor.apana.org.au> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Arnaldo Carvalho de Melo 提交于
Signed-off-by: NArnaldo Carvalho de Melo <acme@ghostprotocols.net> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-