The condition must be checked after perpare_to_wait(). The old
implementaion could loose wakeup events. Never observed in real
life.
Signed-off-by: NPhilipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: NLars Ellenberg <lars.ellenberg@linbit.com>

Signed-off-by: NPhilipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: NLars Ellenberg <lars.ellenberg@linbit.com>

Since inc_ap_bio() might sleep already
Signed-off-by: NPhilipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: NLars Ellenberg <lars.ellenberg@linbit.com>

Before:
  drbd_rs_begin_io() locked app-IO out of an RS extent, and
  waited then until all previous app-IO in that area finished.
  (But not only until the disk-IO was finished but until the
   barrier/epoch ack came in for that == round trip time latency ++)

After:
  As soon as a new app-IO waits wants to start new IO on that
  RS extent, drbd_rs_begin_io() steps aside (clearing the
  BME_NO_WRITES flag again). It retries after 100ms.
Signed-off-by: NPhilipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: NLars Ellenberg <lars.ellenberg@linbit.com>

Signed-off-by: NPhilipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: NLars Ellenberg <lars.ellenberg@linbit.com>

We only issue resync requests if there is no significant application IO
going on. = Application IO has higher priority than resnyc IO.

If application IO can not be started because the resync process locked
an resync_lru entry, start the IO operations necessary to release the
lock ASAP.
Signed-off-by: NPhilipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: NLars Ellenberg <lars.ellenberg@linbit.com>

This one should be replaced with moving this cleanup to the
'right' position.
Signed-off-by: NPhilipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: NLars Ellenberg <lars.ellenberg@linbit.com>

Signed-off-by: NPhilipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: NLars Ellenberg <lars.ellenberg@linbit.com>

Signed-off-by: NPhilipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: NLars Ellenberg <lars.ellenberg@linbit.com>

In this connection mode, the ahead node no longer replicates
application IO. The behind's disk becomes out dated.
Signed-off-by: NPhilipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: NLars Ellenberg <lars.ellenberg@linbit.com>

net {
    on_congestion {block|pull-ahead|disconnect};
    congestion-fill {sectors};
    congestion-extents {al-extents};
}
Signed-off-by: NPhilipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: NLars Ellenberg <lars.ellenberg@linbit.com>

Signed-off-by: NPhilipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: NLars Ellenberg <lars.ellenberg@linbit.com>

Signed-off-by: NPhilipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: NLars Ellenberg <lars.ellenberg@linbit.com>

With commit
drbd: further converge progress display of resync and online-verify
accidentally an u64/u64 div was introduced, causing an unresolvable
symbol __udivdi3 to be reference. Actually for that division, 32bit are
still suficient for now, so we can revert to unsigned long instead.
Signed-off-by: NPhilipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: NLars Ellenberg <lars.ellenberg@linbit.com>

To ease tracking of bios in some hash tables, we want it to
not cross certain boundaries (128k, used to be 32k).
We limit the maximum bio size using queue parameters.

Historically some defines and variables we use there have been named
max_segment_size, which was misguided. Rename them to max_bio_size,
and use [blk_]queue_max_hw_sectors where appropriate.
Signed-off-by: NPhilipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: NLars Ellenberg <lars.ellenberg@linbit.com>

We used to be limited to 32k requests,
but have increased that limit to 128k now.

This part of the code can only deal with 32k,
it would scramble arbitrary pages for larger requests.

As it is used for debugging only anyways,
it is ok to simply truncate the dumped data here.
Signed-off-by: NPhilipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: NLars Ellenberg <lars.ellenberg@linbit.com>

With data-integrity digest enabled, double-check on the sending side
for modifications by upper layers of buffers under write back,
so we can tell it appart from corruption on the "wire".
Signed-off-by: NPhilipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: NLars Ellenberg <lars.ellenberg@linbit.com>

Show progressbar and ETA always, with proc_details >= 1 also show the
current sector position for both resync and online-verify on both nodes.
Signed-off-by: NPhilipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: NLars Ellenberg <lars.ellenberg@linbit.com>

When converting bits (4k resolution, still) to kB, we shift left.  If it
was a large number of bits on a 32bit box (>= 4 TiB storage), we may
wrap the 32bit unsigned long base type, resulting in incorrect display.
Signed-off-by: NPhilipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: NLars Ellenberg <lars.ellenberg@linbit.com>

Signed-off-by: NPhilipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: NLars Ellenberg <lars.ellenberg@linbit.com>

Preparation patch to be able to use the auto-throttling resync controller
for online-verify requests as well.
Signed-off-by: NPhilipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: NLars Ellenberg <lars.ellenberg@linbit.com>

Preparation patch to be able to use the auto-throttling resync controller
for online-verify requests as well.
Signed-off-by: NPhilipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: NLars Ellenberg <lars.ellenberg@linbit.com>

Signed-off-by: NPhilipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: NLars Ellenberg <lars.ellenberg@linbit.com>

Signed-off-by: NPhilipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: NLars Ellenberg <lars.ellenberg@linbit.com>

This is in preparation to unify progress reporting of
online-verify and resync requests.
Signed-off-by: NPhilipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: NLars Ellenberg <lars.ellenberg@linbit.com>

For partial (resumed) online verify, initialize the resync step marks
once we know what the online verify start sector is.
Signed-off-by: NPhilipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: NLars Ellenberg <lars.ellenberg@linbit.com>

For a partial (resumed) online-verify, initialize rs_total not to total
bits, but to number of bits to check in this run, to match the meaning
rs_total has for actual resync.
Signed-off-by: NPhilipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: NLars Ellenberg <lars.ellenberg@linbit.com>

For network hickups during online-verify, on the next verify
triggered, we by default want to resume where it left off.

After any replication link interruption, there will be a (possibly
empty) resync.  Do not reset online-verify start sector if some resync
completed, that would defeats the purpose.

Only reset the start sector once a verify run is completed.
Signed-off-by: NPhilipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: NLars Ellenberg <lars.ellenberg@linbit.com>

With the plugging now being explicitly controlled by the
submitter, callers need not pass down unplugging hints
to the block layer. If they want to unplug, it's because they
manually plugged on their own - in which case, they should just
unplug at will.
Signed-off-by: NJens Axboe <jaxboe@fusionio.com>

Code has been converted over to the new explicit on-stack plugging,
and delay users have been converted to use the new API for that.
So lets kill off the old plugging along with aops->sync_page().
Signed-off-by: NJens Axboe <jaxboe@fusionio.com>

It was always abuse to reuse the plugging infrastructure for this,
convert it to the (new) real API for delaying queueing a bit. A
default delay of 3 msec is defined, to match the previous
behaviour.
Signed-off-by: NJens Axboe <jaxboe@fusionio.com>

It was always abuse to reuse the plugging infrastructure for this,
convert it to the (new) real API for delaying queueing a bit.
Signed-off-by: NJens Axboe <jaxboe@fusionio.com>
Acked-by: NDavid S. Miller <davem@davemloft.net>

Convert two staging drivers - blkvsc_drv and cyasblkdev_block - from
->media_changed() to ->check_events().  The former always indicated
media changed while the latter always indicated media not changed.
Not sure what the drivers are trying to achieve but keep the original
behavior.
Signed-off-by: NTejun Heo <tj@kernel.org>
Acked-by: NGreg Kroah-Hartman <gregkh@suse.de>
Cc: Jens Axboe <axboe@kernel.dk>
Cc: Kay Sievers <kay.sievers@vrfy.org>

Convert from ->media_changed() to ->check_events().

pktcdvd needs to forward all event related operations to the
underlying device.  Forward ->check_events() instead of
->media_changed() and inherit disk->[async_]events.
Signed-off-by: NTejun Heo <tj@kernel.org>
Cc: Jens Axboe <axboe@kernel.dk>
Cc: Kay Sievers <kay.sievers@vrfy.org>
Cc: Peter Osterlund <petero2@telia.com>

umem doesn't implement media changed detection and there's no need to
implement dummy callback anymore.  Remove it.
Signed-off-by: NTejun Heo <tj@kernel.org>
Cc: Jens Axboe <axboe@kernel.dk>
Cc: Kay Sievers <kay.sievers@vrfy.org>

Convert from ->media_changed() to ->check_events().

s390/tape_block buffers media changed state and clears it on
revalidation.  It will behave correctly with kernel event polling.
Signed-off-by: NTejun Heo <tj@kernel.org>
Cc: Jens Axboe <axboe@kernel.dk>
Cc: Kay Sievers <kay.sievers@vrfy.org>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>

Convert from ->media_changed() to ->check_events().

i2o_block buffers media changed state and clears it after reporting.
It will behave correctly with kernel event polling.
Signed-off-by: NTejun Heo <tj@kernel.org>
Cc: Jens Axboe <axboe@kernel.dk>
Cc: Kay Sievers <kay.sievers@vrfy.org>
Cc: Markus Lidel <Markus.Lidel@shadowconnect.com>

Convert from ->media_changed() to ->check_events().

xsysace buffers media changed state and clears it on revalidation.  It
will behave correctly with kernel event polling.
Signed-off-by: NTejun Heo <tj@kernel.org>
Acked-by: NGrant Likely <grant.likely@secretlab.ca>
Cc: Jens Axboe <axboe@kernel.dk>
Cc: Kay Sievers <kay.sievers@vrfy.org>

Convert from ->media_changed() to ->check_events().

ub buffers media changed state and clears it on revalidation.  It will
behave correctly with kernel event polling.
Signed-off-by: NTejun Heo <tj@kernel.org>
Cc: Jens Axboe <axboe@kernel.dk>
Cc: Kay Sievers <kay.sievers@vrfy.org>
Cc: Pete Zaitcev <zaitcev@redhat.com>

Convert from ->media_changed() to ->check_events().

Both swim and swim3 buffer media changed state and clear it on
revalidation.  They will behave correctly with kernel event polling.
Signed-off-by: NTejun Heo <tj@kernel.org>
Cc: Jens Axboe <axboe@kernel.dk>
Cc: Kay Sievers <kay.sievers@vrfy.org>
Cc: Laurent Vivier <laurent@lvivier.info>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>