Skip to content

cloud-kernel
cloud-kernel

openanolis / cloud-kernel
1 年多 前同步成功

通知 161
Star 36
Fork 7
cloud-kernel
cloud-kernel
切换分支/标签
  1. 02 12月, 2015 6 次提交
  3. 19 11月, 2015 1 次提交
  5. 11 11月, 2015 1 次提交
    • A
      qed: select ZLIB_INFLATE · 4bdb96cb
      由 Arnd Bergmann 提交于 
      The newly added qlogic qed driver uses the zlib library, but
misses the dependency:

drivers/built-in.o: In function `qed_alloc_stream_mem':
drivers/net/ethernet/qlogic/qed/qed_main.c:707: undefined reference to `zlib_inflate_workspacesize'
drivers/built-in.o: In function `qed_unzip_data':
drivers/net/ethernet/qlogic/qed/qed_main.c:675: undefined reference to `zlib_inflateInit2'

This changes Kconfig to always select zlib when needed.
Signed-off-by: NArnd Bergmann <arnd@arndb.de>
Fixes: fe56b9e6 ("qed: Add module with basic common support")
Signed-off-by: NDavid S. Miller <davem@davemloft.net>
      4bdb96cb
  7. 08 11月, 2015 1 次提交
    • J
      net/qlcnic: fix mac address restore in bond mode 5/6 · e824de8a
      由 Jarod Wilson 提交于 
      The bonding driver saves a copy of slaves' original mac address and then
assigns whatever mac as needed to the slave, depending on mode. In at
least modes 5 and 6 (balance-tlb, balance-alb), it often ends up being the
mac address of another slave. On release from the bond, the original mac
address is supposed to get restored via a dev_set_mac_address() call in
the bonding driver's __bond_release_one() function, which calls the
slave's ndo_set_mac_address function, which for qlcnic, is
qlcnic_set_mac().

Now, this function tries to be somewhat intelligent and exit early if
you're trying to set the mac address to the same thing that is already
set. The problem here is that adapter->mac_addr isn't in sync with
netdev->dev_addr. The qlcnic driver still has the original mac stored in
adapter->mac_addr, while the bonding driver has updated netdev->dev_addr,
so qlcnic thinks we're trying to set the same address it already has.

I think the way to go here, since the function updates both netdev and
adapter's stored mac addresses, is to check if either of them doesn't
match the newly requested mac. Simply checking netdev's value only could
result in a similar mismatch and non-update, so look at both.

CC: Dept-GELinuxNICDev@qlogic.com
CC: netdev@vger.kernel.org
CC: Manish Chopra <manish.chopra@qlogic.com>
Signed-off-by: NJarod Wilson <jarod@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>
      e824de8a
  9. 06 11月, 2015 1 次提交
  11. 05 11月, 2015 2 次提交
  13. 28 10月, 2015 10 次提交
  15. 16 10月, 2015 1 次提交
  17. 13 10月, 2015 1 次提交
  19. 18 9月, 2015 1 次提交
  21. 10 9月, 2015 1 次提交
  23. 11 8月, 2015 6 次提交
  25. 30 7月, 2015 1 次提交
  27. 16 7月, 2015 1 次提交
  29. 23 6月, 2015 1 次提交
    • P
      drivers/net: remove all references to obsolete Ethernet-HOWTO · 138b15ed
      由 Paul Gortmaker 提交于 
      This howto made sense in the 1990s when users had to manually configure
ISA cards with jumpers or vendor utilities, but with the implementation
of PCI it became increasingly less and less relevant, to the point where
it has been well over a decade since I last updated it.  And there is
no value in anyone else taking over updating it either.

However the references to it continue to spread as boiler plate text
from one Kconfig file into the next.  We are not doing end users any
favours by pointing them at this old document, so lets kill it with
fire, once and for all, to hopefully stop any further spread.

No code is changed in this commit, just Kconfig help text.
Signed-off-by: NPaul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>
      138b15ed
  31. 29 5月, 2015 1 次提交
  33. 27 5月, 2015 1 次提交
  35. 22 5月, 2015 1 次提交
  37. 10 5月, 2015 1 次提交
  39. 01 5月, 2015 1 次提交