ACPI spec states that the OS evaluates _STA after calling _EJ0
in order to verify if eject was successful.  Added a check to
verify if the enabled bit of the status value is cleared after
_EJ0.

Note, the present bit is not checked since some FW implementations
do not clear the present bit until the hardware is physically
removed.
Signed-off-by: NToshi Kani <toshi.kani@hp.com>
Signed-off-by: NRafael J. Wysocki <rafael.j.wysocki@intel.com>

The Kconfig entry for ACPI Container and Module Devices got
added in v2.6.11. Its default value has always been set to
    (ACPI_HOTPLUG_MEMORY || ACPI_HOTPLUG_CPU || ACPI_HOTPLUG_IO)

But the Kconfig symbol ACPI_HOTPLUG_IO has never existed. So it's
pointless to use it to set this default value.
Signed-off-by: NPaul Bolle <pebolle@tiscali.nl>
Signed-off-by: NRafael J. Wysocki <rafael.j.wysocki@intel.com>

When the kernel calls _OSC with OSC_SB_HOTPLUG_OST_SUPPORT bit
set at boot-time, the OS is responsible for calling _OST for
ACPI hotplug events.  However, when hotplug.enabled attribute
is unset for ACPI scan drivers, their notify handlers are removed
and _OST is not called for ACPI hotplug events as a result.

This patch keeps the notify handler of ACPI scan drivers,
acpi_hotplug_notify_cb(), installed regardless of the state of
hotplug.enabled.  The notify handler then checks if hotplug.enabled
is set for the associated scan handler.  If unset, the notify
handler calls _OST with a proper error code.  The patch also
eliminates ACPI namespace walk when hotplug.enabled is changed
via sysfs.
Signed-off-by: NToshi Kani <toshi.kani@hp.com>
Signed-off-by: NRafael J. Wysocki <rafael.j.wysocki@intel.com>

When installing/removing a notify handler to/from an ACPI device
object, ACPI core tries to match its associated scan handler to
see if it supports hotplug.  However, the matching logic of the
notify handler is different from the matching logic of attaching
a scan handler to an ACPI device object.  This patch updates the
matching logic of the notify handlers to be consistent with the
attach handling.
Signed-off-by: NToshi Kani <toshi.kani@hp.com>
Signed-off-by: NRafael J. Wysocki <rafael.j.wysocki@intel.com>

This patch introduces acpi_set_pnp_ids() and acpi_free_pnp_ids(),
which are updated from acpi_device_set_id() and acpi_free_ids(),
to setup and free acpi_device_pnp for a given acpi_handle.  They
can be called without acpi_device.
Signed-off-by: NToshi Kani <toshi.kani@hp.com>
Signed-off-by: NRafael J. Wysocki <rafael.j.wysocki@intel.com>

This patch updates the internal operations of acpi_device_set_id()
to setup acpi_device_pnp without using acpi_device.  There is no
functional change to acpi_device_set_id() in this patch.

acpi_pnp_type is added to acpi_device_pnp, so that PNPID type is
self-contained within acpi_device_pnp.  acpi_add_id(), acpi_bay_match(),
acpi_dock_match(), acpi_ibm_smbus_match() and acpi_is_video_device()
are changed to take acpi_handle as an argument, instead of acpi_device.
Signed-off-by: NToshi Kani <toshi.kani@hp.com>
Signed-off-by: NRafael J. Wysocki <rafael.j.wysocki@intel.com>

The acpi_hotplug_profile_ktype object should be static, so make that
be the case.
Reported-by: NFengguang Wu <fengguang.wu@intel.com>
Signed-off-by: NRafael J. Wysocki <rafael.j.wysocki@intel.com>

Make the ACPI memory hotplug driver use struct acpi_scan_handler
for representing the object used to set up ACPI memory hotplug
functionality and to remove hotplug memory ranges and data
structures used by the driver before unregistering ACPI device
nodes representing memory.  Register the new struct acpi_scan_handler
object with the help of acpi_scan_add_handler_with_hotplug() to allow
user space to manipulate the attributes of the memory hotplug
profile.

This results in a significant reduction of the drvier's code size
and removes some ACPI hotplug code duplication.
Signed-off-by: NRafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: NToshi Kani <toshi.kani@hp.com>
Tested-by: NToshi Kani <toshi.kani@hp.com>

Make the ACPI container driver register its ACPI scan handler object
using acpi_scan_add_handler_with_hotplug() to allow user space to
manipulate its hotplug profile attributes.
Signed-off-by: NRafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: NToshi Kani <toshi.kani@hp.com>
Tested-by: NToshi Kani <toshi.kani@hp.com>

Introduce user space interface for manipulating hotplug profiles
associated with ACPI scan handlers.

The interface consists of sysfs directories under
/sys/firmware/acpi/hotplug/, one for each hotplug profile, containing
an attribute allowing user space to manipulate the enabled field of
the corresponding profile.  Namely, switching the enabled attribute
from '0' to '1' will cause the common hotplug notify handler to be
installed for all ACPI namespace objects representing devices matching
the scan handler associated with the given hotplug profile (and
analogously for the converse switch).

Drivers willing to use the new user space interface should add their
ACPI scan handlers with the help of new funtion
acpi_scan_add_handler_with_hotplug().
Signed-off-by: NRafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: NToshi Kani <toshi.kani@hp.com>
Tested-by: NToshi Kani <toshi.kani@hp.com>

Introduce new helper routine acpi_scan_handler_matching() for
checking if the given ACPI scan handler matches a given device ID
and rework acpi_scan_match_handler() to use the new routine (that
routine will also be useful for other purposes in the future).
Signed-off-by: NRafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: NYasuaki Ishimatsu <isimatu.yasuaki@jp.fujitsu.com>
Acked-by: NToshi Kani <toshi.kani@hp.com>
Tested-by: NToshi Kani <toshi.kani@hp.com>

Switch the ACPI container driver to using common device hotplug code
introduced previously.  This reduces the driver down to a trivial
definition and registration of a struct acpi_scan_handler object.
Signed-off-by: NRafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: NToshi Kani <toshi.kani@hp.com>
Tested-by: NToshi Kani <toshi.kani@hp.com>

Multiple drivers handling hotplug-capable ACPI device nodes install
notify handlers covering the same types of events in a very similar
way.  Moreover, those handlers are installed in separate namespace
walks, although that really should be done during namespace scans
carried out by acpi_bus_scan().  This leads to substantial code
duplication, unnecessary overhead and behavior that is hard to
follow.

For this reason, introduce common code in drivers/acpi/scan.c for
handling hotplug-related notification and carrying out device
insertion and eject operations in a generic fashion, such that it
may be used by all of the relevant drivers in the future.  To cover
the existing differences between those drivers introduce struct
acpi_hotplug_profile for representing collections of hotplug
settings associated with different ACPI scan handlers that can be
used by the drivers to make the common code reflect their current
behavior.
Signed-off-by: NRafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: NToshi Kani <toshi.kani@hp.com>
Tested-by: NToshi Kani <toshi.kani@hp.com>

Introduce helper routine acpi_scan_match_handler() that will find the
ACPI scan handler matching a given device ID, if there is one, and
rework acpi_scan_attach_handler() to use the new routine (that
routine will also be useful for other purposes going forward).
Signed-off-by: NRafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: NYasuaki Ishimatsu <isimatu.yasuaki@jp.fujitsu.com>
Acked-by: NToshi Kani <toshi.kani@hp.com>
Tested-by: NToshi Kani <toshi.kani@hp.com>

Meta core internal interrupts (from HWSTATMETA and friends) are vectored
onto the TR1 core trigger for the current thread. This is demultiplexed
in irq-metag.c to individual Linux IRQs for each internal interrupt.

External SoC interrupts (from HWSTATEXT and friends) are vectored onto
the TR2 core trigger for the current thread. This is demultiplexed in
irq-metag-ext.c to individual Linux IRQs for each external SoC interrupt.
The external irqchip has devicetree bindings for configuring the number
of irq banks and the type of masking available.
Signed-off-by: NJames Hogan <james.hogan@imgtec.com>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Grant Likely <grant.likely@secretlab.ca>
Cc: Rob Herring <rob.herring@calxeda.com>
Cc: Rob Landley <rob@landley.net>
Cc: Dom Cobley <popcornmix@gmail.com>
Cc: Simon Arlott <simon@fire.lp0.eu>
Cc: Viresh Kumar <viresh.kumar@linaro.org>
Cc: Maxime Ripard <maxime.ripard@free-electrons.com>
Cc: devicetree-discuss@lists.ozlabs.org
Cc: linux-doc@vger.kernel.org

Add time keeping code for metag. Meta hardware threads have 2 timers.
The background timer (TXTIMER) is used as a free-running time base, and
the interrupt timer (TXTIMERI) is used for the timer interrupt. Both
counters traditionally count at approximately 1MHz.
Signed-off-by: NJames Hogan <james.hogan@imgtec.com>
Cc: John Stultz <johnstul@us.ibm.com>
Cc: Thomas Gleixner <tglx@linutronix.de>

additionally comment out unused code (which may be used later)
Signed-off-by: NHelge Deller <deller@gmx.de>

Tim found:

  WARNING: at arch/x86/kernel/smpboot.c:324 topology_sane.isra.2+0x6f/0x80()
  Hardware name: S2600CP
  sched: CPU #1's llc-sibling CPU #0 is not on the same node! [node: 1 != 0]. Ignoring dependency.
  smpboot: Booting Node   1, Processors  #1
  Modules linked in:
  Pid: 0, comm: swapper/1 Not tainted 3.9.0-0-generic #1
  Call Trace:
    set_cpu_sibling_map+0x279/0x449
    start_secondary+0x11d/0x1e5

Don Morris reproduced on a HP z620 workstation, and bisected it to
commit e8d19552 ("acpi, memory-hotplug: parse SRAT before memblock
is ready")

It turns out movable_map has some problems, and it breaks several things

1. numa_init is called several times, NOT just for srat. so those
	nodes_clear(numa_nodes_parsed)
	memset(&numa_meminfo, 0, sizeof(numa_meminfo))
   can not be just removed.  Need to consider sequence is: numaq, srat, amd, dummy.
   and make fall back path working.

2. simply split acpi_numa_init to early_parse_srat.
   a. that early_parse_srat is NOT called for ia64, so you break ia64.
   b.  for (i = 0; i < MAX_LOCAL_APIC; i++)
	     set_apicid_to_node(i, NUMA_NO_NODE)
     still left in numa_init. So it will just clear result from early_parse_srat.
     it should be moved before that....
   c.  it breaks ACPI_TABLE_OVERIDE...as the acpi table scan is moved
       early before override from INITRD is settled.

3. that patch TITLE is total misleading, there is NO x86 in the title,
   but it changes critical x86 code. It caused x86 guys did not
   pay attention to find the problem early. Those patches really should
   be routed via tip/x86/mm.

4. after that commit, following range can not use movable ram:
  a. real_mode code.... well..funny, legacy Node0 [0,1M) could be hot-removed?
  b. initrd... it will be freed after booting, so it could be on movable...
  c. crashkernel for kdump...: looks like we can not put kdump kernel above 4G
	anymore.
  d. init_mem_mapping: can not put page table high anymore.
  e. initmem_init: vmemmap can not be high local node anymore. That is
     not good.

If node is hotplugable, the mem related range like page table and
vmemmap could be on the that node without problem and should be on that
node.

We have workaround patch that could fix some problems, but some can not
be fixed.

So just remove that offending commit and related ones including:

 f7210e6c ("mm/memblock.c: use CONFIG_HAVE_MEMBLOCK_NODE_MAP to
    protect movablecore_map in memblock_overlaps_region().")

 01a178a9 ("acpi, memory-hotplug: support getting hotplug info from
    SRAT")

 27168d38 ("acpi, memory-hotplug: extend movablemem_map ranges to
    the end of node")

 e8d19552 ("acpi, memory-hotplug: parse SRAT before memblock is
    ready")

 fb06bc8e ("page_alloc: bootmem limit with movablecore_map")

 42f47e27 ("page_alloc: make movablemem_map have higher priority")

 6981ec31 ("page_alloc: introduce zone_movable_limit[] to keep
    movable limit for nodes")

 34b71f1e ("page_alloc: add movable_memmap kernel parameter")

 4d59a751 ("x86: get pg_data_t's memory from other node")

Later we should have patches that will make sure kernel put page table
and vmemmap on local node ram instead of push them down to node0.  Also
need to find way to put other kernel used ram to local node ram.
Reported-by: NTim Gardner <tim.gardner@canonical.com>
Reported-by: NDon Morris <don.morris@hp.com>
Bisected-by: NDon Morris <don.morris@hp.com>
Tested-by: NDon Morris <don.morris@hp.com>
Signed-off-by: NYinghai Lu <yinghai@kernel.org>
Cc: Tony Luck <tony.luck@intel.com>
Cc: Thomas Renninger <trenn@suse.de>
Cc: Tejun Heo <tj@kernel.org>
Cc: Tang Chen <tangchen@cn.fujitsu.com>
Cc: Yasuaki Ishimatsu <isimatu.yasuaki@jp.fujitsu.com>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

We can't look up the address of the entry point of the function simply
via that function symbol for all architectures.

For PPC64 ABI, actually there is a function descriptors structure.

A function descriptor is a three doubleword data structure that contains
the following values:
	* The first doubleword contains the address of the entry point of
		the function.
	* The second doubleword contains the TOC base address for
		the function.
	* The third doubleword contains the environment pointer for
		languages such as Pascal and PL/1.

So we should call a wapperred dereference_function_descriptor() to get
the address of the entry point of the function.

Note this is also safe for other architecture after refer to
"include/asm-generic/sections.h" since:

dereference_function_descriptor(p) always is (p) if without arched definition.
Signed-off-by: NTiejun Chen <tiejun.chen@windriver.com>
Signed-off-by: NJason Wessel <jason.wessel@windriver.com>

A simple cache policy that writes back all data to the origin.

This is used to decommission a dm cache by emptying it.
Signed-off-by: NHeinz Mauelshagen <mauelshagen@redhat.com>
Signed-off-by: NJoe Thornber <ejt@redhat.com>
Signed-off-by: NAlasdair G Kergon <agk@redhat.com>

A cache policy that uses a multiqueue ordered by recent hit
count to select which blocks should be promoted and demoted.
This is meant to be a general purpose policy.  It prioritises
reads over writes.
Signed-off-by: NJoe Thornber <ejt@redhat.com>
Signed-off-by: NAlasdair G Kergon <agk@redhat.com>

Add a target that allows a fast device such as an SSD to be used as a
cache for a slower device such as a disk.

A plug-in architecture was chosen so that the decisions about which data
to migrate and when are delegated to interchangeable tunable policy
modules.  The first general purpose module we have developed, called
"mq" (multiqueue), follows in the next patch.  Other modules are
under development.
Signed-off-by: NJoe Thornber <ejt@redhat.com>
Signed-off-by: NHeinz Mauelshagen <mauelshagen@redhat.com>
Signed-off-by: NMike Snitzer <snitzer@redhat.com>
Signed-off-by: NAlasdair G Kergon <agk@redhat.com>

Add a persistent bitset as a wrapper around dm-array.
Signed-off-by: NJoe Thornber <ejt@redhat.com>
Signed-off-by: NAlasdair G Kergon <agk@redhat.com>

Add a transactional array.
Signed-off-by: NJoe Thornber <ejt@redhat.com>
Signed-off-by: NAlasdair G Kergon <agk@redhat.com>

This patch takes advantage of the new bio-prison interface where the
memory is now passed in rather than using a mempool in bio-prison.
This allows the map function to avoid performing potentially-blocking
allocations that could lead to deadlocks: We want to avoid the cell
allocation that is done in bio_detain.

(The potential for mempool deadlocks still remains in other functions
that use bio_detain.)
Signed-off-by: NJoe Thornber <ejt@redhat.com>
Signed-off-by: NAlasdair G Kergon <agk@redhat.com>

Change the dm_bio_prison interface so that instead of allocating memory
internally, dm_bio_detain is supplied with a pre-allocated cell each
time it is called.

This enables a subsequent patch to move the allocation of the struct
dm_bio_prison_cell outside the thin target's mapping function so it can
no longer block there.
Signed-off-by: NJoe Thornber <ejt@redhat.com>
Signed-off-by: NAlasdair G Kergon <agk@redhat.com>

Add dm_btree_walk to iterate through the contents of a btree.
This will be used by the dm cache target.
Signed-off-by: NJoe Thornber <ejt@redhat.com>
Signed-off-by: NAlasdair G Kergon <agk@redhat.com>

Add a num_write_bios function to struct target.

If an instance of a target sets this, it will be queried before the
target's mapping function is called on a write bio, and the response
controls the number of copies of the write bio that the target will
receive.

This provides a convenient way for a target to send the same data to
more than one device.  The new cache target uses this in writethrough
mode, to send the data both to the cache and the backing device.
Signed-off-by: NAlasdair G Kergon <agk@redhat.com>

This patch allows the administrator to reduce the rate at which kcopyd
issues I/O.

Each module that uses kcopyd acquires a throttle parameter that can be
set in /sys/module/*/parameters.

We maintain a history of kcopyd usage by each module in the variables
io_period and total_period in struct dm_kcopyd_throttle. The actual
kcopyd activity is calculated as a percentage of time equal to
"(100 * io_period / total_period)".  This is compared with the user-defined
throttle percentage threshold and if it is exceeded, we sleep.
Signed-off-by: NMikulas Patocka <mpatocka@redhat.com>
Signed-off-by: NAlasdair G Kergon <agk@redhat.com>

This patch introduces enhanced message support that allows the
device-mapper core to recognise messages that are common to all devices,
and for messages to return data to userspace.

Core messages are processed by the function "message_for_md".  If the
device mapper doesn't support the message, it is passed to the target
driver.

If the message returns data, the kernel sets the flag
DM_MESSAGE_OUT_FLAG.
Signed-off-by: NMikulas Patocka <mpatocka@redhat.com>
Signed-off-by: NAlasdair G Kergon <agk@redhat.com>

Device-mapper ioctls receive and send data in a buffer supplied
by userspace.  The buffer has two parts.  The first part contains
a 'struct dm_ioctl' and has a fixed size.  The second part depends
on the ioctl and has a variable size.

This patch recognises the specific ioctls that do not use the variable
part of the buffer and skips allocating memory for it.

In particular, when a device is suspended and a resume ioctl is sent,
this now avoid memory allocation completely.

The variable "struct dm_ioctl tmp" is moved from the function
copy_params to its caller ctl_ioctl and renamed to param_kernel.
It is used directly when the ioctl function doesn't need any arguments.
Signed-off-by: NMikulas Patocka <mpatocka@redhat.com>
Signed-off-by: NAlasdair G Kergon <agk@redhat.com>

This patch introduces flags for each ioctl function.

So far, one flag is defined, IOCTL_FLAGS_NO_PARAMS.  It is set if the
function processing the ioctl doesn't take or produce any parameters in
the section of the data buffer that has a variable size.
Signed-off-by: NMikulas Patocka <mpatocka@redhat.com>
Signed-off-by: NAlasdair G Kergon <agk@redhat.com>

This patch merges io_pool and tio_pool into io_pool and cleans up
related functions.

Though device-mapper used to have 2 pools of objects for each dm device,
the use of bioset frontbad for per-bio data has shrunk the number of
pools to 1 for both bio-based and request-based device types.
(See c0820cf5 "dm: introduce per_bio_data" and
 94818742 "dm: Use bioset's front_pad for dm_rq_clone_bio_info")

So dm no longer has to maintain 2 different pointers.

No functional changes.
Signed-off-by: NJun'ichi Nomura <j-nomura@ce.jp.nec.com>
Signed-off-by: NAlasdair G Kergon <agk@redhat.com>

Remove _rq_bio_info_cache, which is no longer used.
No functional changes.
Signed-off-by: NJun'ichi Nomura <j-nomura@ce.jp.nec.com>
Signed-off-by: NAlasdair G Kergon <agk@redhat.com>

dm_calculate_queue_limits will first reset the provided limits to
defaults using blk_set_stacking_limits; whereby defeating the purpose of
retaining the original live table's limits -- as was intended via commit
3ae70656 ("dm: retain table limits when
swapping to new table with no devices").

Fix this improper limits initialization (in the no data devices case) by
avoiding the call to dm_calculate_queue_limits.

[patch header revised by Mike Snitzer]
Signed-off-by: NMike Christie <michaelc@cs.wisc.edu>
Signed-off-by: NMike Snitzer <snitzer@redhat.com>
Cc: stable@vger.kernel.org # v3.6+
Signed-off-by: NAlasdair G Kergon <agk@redhat.com>

Add module aliases so that autoloading works correctly if the user
tries to activate "snapshot-origin" or "snapshot-merge" targets.

Reference: https://bugzilla.redhat.com/889973Reported-by: NChao Yang <chyang@redhat.com>
Signed-off-by: NMikulas Patocka <mpatocka@redhat.com>
Cc: stable@vger.kernel.org
Signed-off-by: NAlasdair G Kergon <agk@redhat.com>

Mark some constant parameters constant in some dm-btree functions.
Signed-off-by: NMike Snitzer <snitzer@redhat.com>
Signed-off-by: NAlasdair G Kergon <agk@redhat.com>

Refactor part of the bio splitting and cloning code to try to make it
easier to understand.
Signed-off-by: NAlasdair G Kergon <agk@redhat.com>

Rename functions involved in splitting and cloning bios.

The sequence of functions is now:
  (1) __split_and_process* - entry point that selects the processing strategy
  (2) __send* - prepare the details for each bio needed and loop through them
  (3) __clone_and_map* - creates a clone and maps it
Signed-off-by: NAlasdair G Kergon <agk@redhat.com>

Use 'bio' in the name of variables and functions that deal with
bios rather than 'request' to avoid confusion with the normal
block layer use of 'request'.

No functional changes.
Signed-off-by: NAlasdair G Kergon <agk@redhat.com>