Signed-off-by: NVipul Pandya <vipul@chelsio.com>
Signed-off-by: NSteve Wise <swise@opengridcomputing.com>
Signed-off-by: NRoland Dreier <roland@purestorage.com>

WakeOnLan was broken in this driver because gp->asleep_wol is a 1-bit
bitfield and it was being assigned WAKE_MAGIC, which is (1 << 5).
gp->asleep_wol remains 0 and the machine never wakes up.  Fixed by casting
gp->wake_on_lan to bool.  Tested on an iBook G4.
Signed-off-by: NGerard Lledo <gerard.lledo@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Creating a VLAN interface on top of ucc_geth adds 4 bytes
to the frame and the HW controller is not prepared to
TX a frame bigger than 1518 bytes which is 4 bytes too
small for a full VLAN frame. Add 16 bytes which will handle
the a simple VLAN and leaves 12 bytes for future expansion.
Signed-off-by: NJoakim Tjernlund <Joakim.Tjernlund@transmode.se>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

In a busy network we see ucc_geth is dropping RX pkgs every now
and then. Increase the RX queues HW descriptors from
16 to 32 to deal with this.
Signed-off-by: NJoakim Tjernlund <Joakim.Tjernlund@transmode.se>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Bug: The VLAN bit of the MAC RX Status Word is unreliable in several older
supported chips. Sometimes the VLAN bit is not set for valid VLAN packets
and also sometimes the VLAN bit is set for non-VLAN packets that came after
a VLAN packet. This results in a receive length error when VLAN hardware
tagging is enabled.

Fix: Variation on original fix proposed by Mirko.
The VLAN information is decoded in the status loop, and can be
applied to the received SKB there. This eliminates the need for the
separate tag field in the interface data structure. The tag has to
be copied and cleared if packet is copied. This version checked out
with vlan and normal traffic.

Note: vlan_tx_tag_present should be renamed vlan_tag_present, but that
is outside scope of this.
Reported-by: NMirko Lindner <mlindner@marvell.com>
Signed-off-by: NStephen Hemminger <shemminger@vyatta.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When a small packet is received, the driver copies it to a new skb to allow
reusing the full size Rx buffer. The copy was propogating the checksum offload
but not the receive hash information. The bug is impact was mostly harmless
and therefore not observed until reviewing this area of code.
Signed-off-by: NStephen Hemminger <shemminger@vyatta.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The driver calls cxgb_vlan_mode() from init_one().  This calls into
synchronize_rx(), which locks all the q locks, but the q locks are not
initialized until cxgb_up() -> setup_sge_qsets().  So move the call to
cxgb_vlan_mode() into cxgb_up(), after the call to setup_sge_qsets().
We also move the body of these functions up higher to avoid having to
a forward declaration.

This was found because of the lockdep warning:

    INFO: trying to register non-static key.
    the code is fine but needs lockdep annotation.
    turning off the locking correctness validator.
    Pid: 323, comm: work_for_cpu Not tainted 3.4.0-rc5 #28
    Call Trace:
     [<ffffffff8106e767>] register_lock_class+0x108/0x2d0
     [<ffffffff8106ff42>] __lock_acquire+0xd3/0xd06
     [<ffffffff81070fd0>] lock_acquire+0xbf/0xfe
     [<ffffffff813862a6>] _raw_spin_lock_irq+0x36/0x45
     [<ffffffffa01e71aa>] cxgb_vlan_mode+0x96/0xcb [cxgb3]
     [<ffffffffa01f90eb>] init_one+0x8c4/0x980 [cxgb3]
     [<ffffffff811fcbf0>] local_pci_probe+0x3f/0x70
     [<ffffffff81042206>] do_work_for_cpu+0x10/0x22
     [<ffffffff810482de>] kthread+0xa1/0xa9
     [<ffffffff8138e234>] kernel_thread_helper+0x4/0x10

Contrary to what lockdep says, the code is not fine: we are locking an
uninitialized spinlock.
Signed-off-by: NRoland Dreier <roland@purestorage.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

With the support to bounce buffer added, the skb is coming as nonlinear in the
case of non-DDPed data frames for FCoE, which is mostly ok as the FCoE stack
would take care of that. However, for target mode, we have to set the FC CRC
and FC EOF field to allow the protocol stack to not drop the frame for the last
data frame of that sequence. So fix this by linearizing the skb first before
doing skb_put().
Signed-off-by: NYi Zou <yi.zou@intel.com>
Tested-by: NMarcus Dennis <marcusx.e.dennis@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

The driver was freeing memory in shutdown instead of remove.  As a result
we were leaking memory if IEEE DCB was enabled and we loaded/unloaded the
driver.  This change moves the freeing of the memory into the remove
routine where it belongs.
Signed-off-by: NAlexander Duyck <alexander.h.duyck@intel.com>
Acked-by: NJohn Fastabend <john.r.fastabend@intel.com>
Tested-by: NRoss Brattain <ross.b.brattain@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Maybe it's a typo, but it cause that igbvf can't be initialized successfully.
Set perm_addr value using valid dev_addr, although which is equal to hw.mac.addr.
Signed-off-by: NSamuel Liao <samuelliao@tencent.com>
Signed-off-by: NShan Wei <davidshan@tencent.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

The dl2k driver's rio_ioctl call has a few issues:
- No permissions checking
- Implements SIOCGMIIREG and SIOCGMIIREG using the SIOCDEVPRIVATE numbers
- Has a few ioctls that may have been used for debugging at one point
  but have no place in the kernel proper.

This patch removes all but the MII ioctls, renumbers them to use the
standard ones, and adds the proper permission check for SIOCSMIIREG.

We can also get rid of the dl2k-specific struct mii_data in favor of
the generic struct mii_ioctl_data.

Since we have the phyid on hand, we can add the SIOCGMIIPHY ioctl too.

Most of the MII code for the driver could probably be converted to use
the generic MII library but I don't have a device to test the results.
Reported-by: NStephan Mueller <stephan.mueller@atsec.com>
Signed-off-by: NJeff Mahoney <jeffm@suse.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

commit a4910b74 has broken promiscuous
mode, which is never set. port->promisc just reflects the last setting
of PROMISCUOUS mode to avoid doing an extra hypercall when it's already
set.

However, since it may fail because of hypervisor permissions, we should
still respect the multicast settings and not simply exit after setting
promiscuous mode.
Signed-off-by: NThadeu Lima de Souza Cascardo <cascardo@linux.vnet.ibm.com>
Cc: Breno Leitao <leitao@linux.vnet.ibm.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

There was a bug in the mask of regtype parameter for registering a
multicast filter. It was ignoring the scope bit, which was wrongly being
used for all filters. The SCOPE_ALL value adds a filter that allows all
multicast packets and ignores the MAC parameter, just what allmulticast
needs. The normals filters, however, should not use SCOPE_ALL.
Signed-off-by: NThadeu Lima de Souza Cascardo <cascardo@linux.vnet.ibm.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When RSS is enabled, interrupt vector 0 does not receive any rx traffic.
The rx producer index fields for vector 0's status block should be
considered reserved in this case.  This patch changes the code to
respect these reserved fields, which avoids a kernel panic when these
fields take on non-zero values.
Signed-off-by: NMatt Carlson <mcarlson@broadcom.com>
Signed-off-by: NMichael Chan <mchan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Changes this beauty into a statement that actually has an effect on amd64.
Tested-by: NPer Jessen <per@opensuse.org>
Signed-off-by: NBenjamin Poirier <bpoirier@suse.de>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Based on the original patch from  Ying Cai <ycai@google.com>
This change ensures that the itr/itr_setting adjustment logic is used,
even for the default/compiled-in value.

Context:
  When we changed the default InterruptThrottleRate value from default
  (3 = dynamic mode) to 8000 for example, only adapter->itr_setting
  (which controls interrupt coalescing mode) was set to 8000, but
  adapter->itr (which controls the value set in NIC register) was not
  updated accordingly. So from ethtool, it seemed the interrupt
  throttling is enabled at 8000 intr/s, but the NIC actually was
  running in dynamic mode which has lower CPU efficiency especially
  when throughput is not high.

CC: Ying Cai <ycai@google.com>
CC: David Decotigny <david.decotigny@google.com>
Signed-off-by: NJeff Kirsher <jeffrey.kirsher@intel.com>
Tested-by: NAaron Brown <aaron.f.brown@intel.com>

Following logs where seen on Systems with multiple NICs,
while using MSI interrupts as shown below:

Feb 16 15:09:32 (none) user.notice kernel: 0000:00:0d.0: lan0_0: NIC Link is Up
1000 Mbps Full Duplex, Flow Control: RX/TX
Feb 16 15:09:32 (none) user.notice kernel: 0000:40:0d.0: wan0_1: NIC Link is Up
1000 Mbps Full Duplex, Flow Control: RX/TX
Feb 16 15:09:32 (none) user.notice kernel: 0000:40:0d.0: lan0_1: NIC Link is Up
1000 Mbps Full Duplex, Flow Control: RX/TX
Feb 16 15:09:32 (none) user.warn kernel: 0000:40:0e.0: wan4_0: MSI interrupt
test failed, using legacy interrupt.
Feb 16 15:09:32 (none) user.notice kernel: 0000:00:0e.0: wan1_0: NIC Link is Up
1000 Mbps Full Duplex, Flow Control: RX/TX
Feb 16 15:09:33 (none) user.notice kernel: 0000:00:0e.0: lan1_0: NIC Link is Up
1000 Mbps Full Duplex, Flow Control: RX/TX
Feb 16 15:09:33 (none) user.notice kernel: 0000:00:0f.0: wan2_0: NIC Link is Up
1000 Mbps Full Duplex, Flow Control: RX/TX
Feb 16 15:09:33 (none) user.notice kernel: 0000:00:0f.0: lan2_0: NIC Link is Up
1000 Mbps Full Duplex, Flow Control: RX/TX
Feb 16 15:09:33 (none) user.notice kernel: 0000:40:0a.0: wan3_0: NIC Link is Up
1000 Mbps Full Duplex, Flow Control: RX/TX
Feb 16 15:09:33 (none) user.notice kernel: 0000:40:0a.0: lan3_0: NIC Link is Up
1000 Mbps Full Duplex, Flow Control: RX/TX
Feb 16 15:09:34 (none) user.notice kernel: 0000:40:0e.0: lan4_0: NIC Link is Up
1000 Mbps Full Duplex, Flow Control: RX/TX
Feb 16 15:09:34 (none) user.notice kernel: 0000:40:0f.0: wan5_0: NIC Link is Up
1000 Mbps Full Duplex, Flow Control: RX/TX
Feb 16 15:09:34 (none) user.notice kernel: 0000:40:0f.0: lan5_0: NIC Link is Up
1000 Mbps Full Duplex, Flow Control: RX/TX

This patch fixes this problem by increasing the msleep from 50 to 100.
Signed-off-by: NPrasanna S Panchamukhi <ppanchamukhi@riverbed.com>
Tested-by: NAaron Brown <aaron.f.brown@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

PHY connect attempts fail if no PHY id is specified in the emac platform
data and another mdio bus has been registered before 'davinci_mdio' bus. In
this case when configuring the interface, there will be an attempt to
connect to already attached PHY on the previously registered mdio bus:

net eth1: PHY already attached
net eth1: could not connect to phy smsc911x-0:01
IP-Config: Failed to open eth1
IP-Config: Device `eth1' not found

Fix this by modifying match_first_device() to match first PHY device
on 'davinci_mdio' bus.
Signed-off-by: NAnatolij Gustschin <agust@denx.de>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

If we receive an interrupt too early before we set up ports in the probe
function, there won't be any port ready to handle it.

Only registering the irq after the ports are setup fixes the problem,
and works fine without losing any interrupts.

This causes crashes in some situations:

[c000000f7ff7fd60] d000000008e223f0 .ehea_neq_tasklet+0x78/0x148 [ehea]
[c000000f7ff7fe00] c0000000000b6cac .tasklet_hi_action+0xdc/0x210
[c000000f7ff7fea0] c0000000000b7cc8 .__do_softirq+0x178/0x300
[c000000f7ff7ff90] c000000000022694 .call_do_softirq+0x14/0x24
[c000000f68ee7900] c000000000010e04 .do_softirq+0xec/0x110
[c000000f68ee79a0] c0000000000b789c .irq_exit+0xac/0xe0
[c000000f68ee7a20] c0000000000110bc .do_IRQ+0x114/0x2a8
[c000000f68ee7ae0] c00000000000553c hardware_interrupt_entry+0x18/0x1c
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Refrain from attempting to free an interrupt line if the request
fails and hence, there is no IRQ to free.

CC: netdev@vger.kernel.org
Signed-off-by: NLee Jones <lee.jones@linaro.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The dev_id parameter passed to free_irq needs to match the one passed
to the corresponding request_irq.
Signed-off-by: NMatt Renzelmann <mjr@cs.wisc.edu>
Acked-by: NStephen Boyd <sboyd@codeaurora.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

There is a potential deadlock scenario when the ks8851 driver
is removed. The interrupt handler schedules a workqueue which
acquires a mutex that ks8851_net_stop() also acquires before
flushing the workqueue. Previously lockdep wouldn't be able
to find this problem but now that it has the support we can
trigger this lockdep warning by rmmoding the driver after
an ifconfig up.

Fix the possible deadlock by disabling the interrupts in
the chip and then release the lock across the workqueue
flushing. The mutex is only there to proect the registers
anyway so this should be ok.

=======================================================
[ INFO: possible circular locking dependency detected ]
3.0.21-00021-g8b33780-dirty #2911
-------------------------------------------------------
rmmod/125 is trying to acquire lock:
 ((&ks->irq_work)){+.+...}, at: [<c019e0b8>] flush_work+0x0/0xac

but task is already holding lock:
 (&ks->lock){+.+...}, at: [<bf00b850>] ks8851_net_stop+0x64/0x138 [ks8851]

which lock already depends on the new lock.

the existing dependency chain (in reverse order) is:

-> #1 (&ks->lock){+.+...}:
       [<c01b89c8>] __lock_acquire+0x940/0x9f8
       [<c01b9058>] lock_acquire+0x10c/0x130
       [<c083dbec>] mutex_lock_nested+0x68/0x3dc
       [<bf00bd48>] ks8851_irq_work+0x24/0x46c [ks8851]
       [<c019c580>] process_one_work+0x2d8/0x518
       [<c019cb98>] worker_thread+0x220/0x3a0
       [<c01a2ad4>] kthread+0x88/0x94
       [<c0107008>] kernel_thread_exit+0x0/0x8

-> #0 ((&ks->irq_work)){+.+...}:
       [<c01b7984>] validate_chain+0x914/0x1018
       [<c01b89c8>] __lock_acquire+0x940/0x9f8
       [<c01b9058>] lock_acquire+0x10c/0x130
       [<c019e104>] flush_work+0x4c/0xac
       [<bf00b858>] ks8851_net_stop+0x6c/0x138 [ks8851]
       [<c06b209c>] __dev_close_many+0x98/0xcc
       [<c06b2174>] dev_close_many+0x68/0xd0
       [<c06b22ec>] rollback_registered_many+0xcc/0x2b8
       [<c06b2554>] rollback_registered+0x28/0x34
       [<c06b25b8>] unregister_netdevice_queue+0x58/0x7c
       [<c06b25f4>] unregister_netdev+0x18/0x20
       [<bf00c1f4>] ks8851_remove+0x64/0xb4 [ks8851]
       [<c049ddf0>] spi_drv_remove+0x18/0x1c
       [<c0468e98>] __device_release_driver+0x7c/0xbc
       [<c0468f64>] driver_detach+0x8c/0xb4
       [<c0467f00>] bus_remove_driver+0xb8/0xe8
       [<c01c1d20>] sys_delete_module+0x1e8/0x27c
       [<c0105ec0>] ret_fast_syscall+0x0/0x3c

other info that might help us debug this:

 Possible unsafe locking scenario:

       CPU0                    CPU1
       ----                    ----
  lock(&ks->lock);
                               lock((&ks->irq_work));
                               lock(&ks->lock);
  lock((&ks->irq_work));

 *** DEADLOCK ***

4 locks held by rmmod/125:
 #0:  (&__lockdep_no_validate__){+.+.+.}, at: [<c0468f44>] driver_detach+0x6c/0xb4
 #1:  (&__lockdep_no_validate__){+.+.+.}, at: [<c0468f50>] driver_detach+0x78/0xb4
 #2:  (rtnl_mutex){+.+.+.}, at: [<c06b25e8>] unregister_netdev+0xc/0x20
 #3:  (&ks->lock){+.+...}, at: [<bf00b850>] ks8851_net_stop+0x64/0x138 [ks8851]

Cc: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: NStephen Boyd <sboyd@codeaurora.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The sp_pri_to_cos[] array size depends on the config but lets say it is
BX_E3B0_MAX_NUM_COS_PORT0 and max_num_of_cos is also
DCBX_E3B0_MAX_NUM_COS_PORT0.  In the original code
"pri == max_num_of_cos" was accepted but it is one past the end of the
array.

Also we used "pri" before capping it.  It's a harmless read past the end
of the array, but it would affect which error message gets printed.
Signed-off-by: NDan Carpenter <dan.carpenter@oracle.com>
Acked-by: NEilon Greenstein <eilong@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

MAX_ADDR_LEN is 32.  ETH_ALEN is 6.  mac->sa_data is a 14 byte array, so
the memcpy() is doing a read past the end of the array.  I asked about
this on netdev and Ben Hutchings told me it's supposed to be copying
ETH_ALEN bytes (thanks Ben).
Signed-off-by: NDan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Under heavy load (flood ping) it is possible for the MDIO timeout to
expire before the loop checks the GO bit again. This patch adds an
additional check whether the operation was done before actually
returning -ETIMEDOUT.

To reproduce this bug, flood ping the device, e.g., ping -f -l 1000
After some time, a "timed out waiting for user access" warning
may appear. And even worse, link may go down since the PHY reported a
timeout.
Signed-off-by: NChristian Riesch <christian.riesch@omicron.at>
Cc: <stable@vger.kernel.org>
Cc: Cyril Chemparathy <cyril@ti.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch makes it so that we identify FCoE rings earlier than
ixgbe_set_rx_buffer_len.  Instead we identify the Rx FCoE rings at
allocation time in ixgbe_alloc_q_vector.

The motivation behind this change is to avoid memory corruption when FCoE
is enabled.  Without this change we were initializing the rings at 0, and
2K on systems with 4K pages, then when we bumped the buffer size to 4K with
order 1 pages we were accessing offsets 2K and 6K instead of 0 and 4K.
This was resulting in memory corruptions.
Signed-off-by: NAlexander Duyck <alexander.h.duyck@intel.com>
Acked-by: NYi Zou <yi.zou@intel.com>
Tested-by: NRoss Brattain <ross.b.brattain@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Upon resume from standby, ixgbe may trigger the ASSERT_RTNL() in
netif_set_real_num_tx_queues(). The call stack is:
	netif_set_real_num_tx_queues
	ixgbe_set_num_queues
	ixgbe_init_interrupt_scheme
	ixgbe_resume
Signed-off-by: NBenjamin Poirier <bpoirier@suse.de>
Tested-by: NStephen Ko <stephen.s.ko@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

At the beginning of ks_rcv(), a for loop retrieves the
header information relevant to all the frames stored
in the mac's internal buffers. The number of pending
frames is stored as an 8 bits field in KS_RXFCTR.
If interrupts are disabled long enough to allow for more than
32 frames to accumulate in the MAC's internal buffers, a buffer
overflow occurs.
This patch fixes the problem by making the
driver's frame_head_info buffer big enough.
Well actually, since the chip appears to have 12K of
internal rx buffers and the shortest ethernet frame should
be 64 bytes long, maybe the limit could be set to
12*1024/64 = 192 frames, but 255 should be safer.
Signed-off-by: NDavide Ciminaghi <ciminaghi@gnudd.com>
Signed-off-by: NRaffaele Recalcati <raffaele.recalcati@bticino.it>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

There are times we turn of the laser before shutdown.  This is a bad thing
if we want to wake on lan to work so now we make sure the laser is on
before shutdown if we support WoL.
Signed-off-by: NDon Skidmore <donald.c.skidmore@intel.com>
Tested-by: NStephen Ko <stephen.s.ko@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

A workaround was previously put in the driver to reset the device when
transitioning to Sx in order to activate the changed settings of the PHY
OEM bits (Low Power Link Up, or LPLU, and GbE disable configuration) for
82577/8/9 devices.  After further review, it was found such a reset can
cause the 82579 to confuse which version of 82579 it actually is and broke
LPLU on all 82577/8/9 devices.  The workaround during an S0->Sx transition
on 82579 (instead of resetting the PHY) is to restart auto-negotiation
after the OEM bits are configured; the restart of auto-negotiation
activates the new OEM bits as does the reset.  With 82577/8, the reset is
changed to a generic reset which fixes the LPLU bits getting set wrong.
Signed-off-by: NBruce Allan <bruce.w.allan@intel.com>
Tested-by: NAaron Brown <aaron.f.brown@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

The SMSC911x driver resets the ->head, ->data and ->tail pointers in the
skb on the reset path in order to avoid buffer overflow due to packet
padding performed by the hardware.

This patch fixes the receive path so that the skb pointers are fixed up
after the data has been read from the device, The error path is also
fixed to use number of words consistently and prevent erroneous FIFO
fastforwarding when skipping over bad data.
Signed-off-by: NWill Deacon <will.deacon@arm.com>
Signed-off-by: NEric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Move the ks8851_rdreg16 call above the call to request_irq and cache
the result for subsequent repeated use.  A spurious interrupt may
otherwise cause a crash.  Thanks to Stephen Boyd, Flavio Leitner, and
Ben Hutchings for feedback.
Signed-off-by: NMatt Renzelmann <mjr@cs.wisc.edu>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Also fix MAINTAINERS file to reflect autorship.

Daniel and Ariane changed coding style but not any functional changes in the driver
itself.
Signed-off-by: NMichal Simek <monstr@monstr.eu>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

We set intr mask before its handler is registered, this does not work well when
8139cp is sharing irq line with other devices. As the irq could be enabled by
the device before 8139cp's hander is registered which may lead unhandled
irq. Fix this by introducing an helper cp_irq_enable() and call it after
request_irq().
Signed-off-by: NJason Wang <jasowang@redhat.com>
Reviewed-by: NFlavio Leitner <fbl@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Problem:
There was two separate work_struct structures which share one
handler. Unfortunately getting atl1_adapter structure from
work_struct in case of DMA error was done from incorrect
offset which cause kernel panics.

Solution:
The useless work_struct for DMA error removed and
handler name changed to more generic one.
Signed-off-by: NTony Zelenoff <antonz@parallels.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Many users of debugfs copy the implementation of default_open() when
they want to support a custom read/write function op.  This leads to a
proliferation of the default_open() implementation across the entire
tree.

Now that the common implementation has been consolidated into libfs we
can replace all the users of this function with simple_open().

This replacement was done with the following semantic patch:

<smpl>
@ open @
identifier open_f != simple_open;
identifier i, f;
@@
-int open_f(struct inode *i, struct file *f)
-{
(
-if (i->i_private)
-f->private_data = i->i_private;
|
-f->private_data = i->i_private;
)
-return 0;
-}

@ has_open depends on open @
identifier fops;
identifier open.open_f;
@@
struct file_operations fops = {
...
-.open = open_f,
+.open = simple_open,
...
};
</smpl>

[akpm@linux-foundation.org: checkpatch fixes]
Signed-off-by: NStephen Boyd <sboyd@codeaurora.org>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Cc: Julia Lawall <Julia.Lawall@lip6.fr>
Acked-by: NIngo Molnar <mingo@elte.hu>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

The driver uses a 2-order allocation, which is too much on architectures
like ppc64, which has a 64KiB page. This particular allocation is used
for large packet fragments that may have a size of 512, 1024, 4096 or
fill the whole allocation. So, a minimum size of 16384 is good enough
and will be the same size that is used in architectures of 4KiB sized
pages.

This will avoid allocation failures that we see when the system is under
stress, but still has plenty of memory, like the one below.

This will also allow us to set the interface MTU to higher values like
9000, which was not possible on ppc64 without this patch.

Node 1 DMA: 737*64kB 37*128kB 0*256kB 0*512kB 0*1024kB 0*2048kB 0*4096kB 0*8192kB 0*16384kB = 51904kB
83137 total pagecache pages
0 pages in swap cache
Swap cache stats: add 0, delete 0, find 0/0
Free swap  = 10420096kB
Total swap = 10420096kB
107776 pages RAM
1184 pages reserved
147343 pages shared
28152 pages non-shared
netstat: page allocation failure. order:2, mode:0x4020
Call Trace:
[c0000001a4fa3770] [c000000000012f04] .show_stack+0x74/0x1c0 (unreliable)
[c0000001a4fa3820] [c00000000016af38] .__alloc_pages_nodemask+0x618/0x930
[c0000001a4fa39a0] [c0000000001a71a0] .alloc_pages_current+0xb0/0x170
[c0000001a4fa3a40] [d00000000dcc3e00] .mlx4_en_alloc_frag+0x200/0x240 [mlx4_en]
[c0000001a4fa3b10] [d00000000dcc3f8c] .mlx4_en_complete_rx_desc+0x14c/0x250 [mlx4_en]
[c0000001a4fa3be0] [d00000000dcc4eec] .mlx4_en_process_rx_cq+0x62c/0x850 [mlx4_en]
[c0000001a4fa3d20] [d00000000dcc5150] .mlx4_en_poll_rx_cq+0x40/0x90 [mlx4_en]
[c0000001a4fa3dc0] [c0000000004e2bb8] .net_rx_action+0x178/0x450
[c0000001a4fa3eb0] [c00000000009c9b8] .__do_softirq+0x118/0x290
[c0000001a4fa3f90] [c000000000031df8] .call_do_softirq+0x14/0x24
[c000000184c3b520] [c00000000000e700] .do_softirq+0xf0/0x110
[c000000184c3b5c0] [c00000000009c6d4] .irq_exit+0xb4/0xc0
[c000000184c3b640] [c00000000000e964] .do_IRQ+0x144/0x230
Signed-off-by: NThadeu Lima de Souza Cascardo <cascardo@linux.vnet.ibm.com>
Signed-off-by: NKleber Sacilotto de Souza <klebers@linux.vnet.ibm.com>
Tested-by: NKleber Sacilotto de Souza <klebers@linux.vnet.ibm.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

In commit (bfab27a1 stmmac: add the experimental PCI support) the
IFF_UNICAST_FLT flag has been removed from the stmmac_mac_device_setup()
function. This patch re-adds the flag.
Signed-off-by: NMarc Kleine-Budde <mkl@pengutronix.de>
Acked-by: NGiuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch clears a warning message of "MDC/MDIO access timeout" which may
appear when interface is loaded due to missing clock setting before resetting
the LED, and starting periodic function too early.
Signed-off-by: NYaniv Rosner <yanivr@broadcom.com>
Signed-off-by: NEilon Greenstein <eilong@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Fix a link problem on the second port of BCM57711 + BCM84823 boards due to
incorrect macro usage.
Signed-off-by: NYaniv Rosner <yanivr@broadcom.com>
Signed-off-by: NEilon Greenstein <eilong@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>