It's a NOOP since 2.6.35 and it will be removed one day.
This is not trivial because current code uses hard coded 32 instead of
IRQF_DISABLED in the request_irq call.
Signed-off-by: NAxel Lin <axel.lin@ingics.com>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

For MMC_BUS_WIDTH_8 case, current code missed setting BM_EIGHTBIT_MODE bit.
Also has a small refactor to make the code looks better in readability.

So the bit settings witch below logic:

SDMMC_BUSMODE register:
Set EIGHTBIT_MODE bit for 8 bit mode, Set FOURBIT_MODE bit for 4 bit mode.
Clear both EIGHTBIT_MODE and FOURBIT_MODE bits for 1 bit mode.

SDMMC_EXTCTRL register:
Set EXT_EIGHTBIT bit for 8 bit mode, Clear EXT_EIGHTBIT bit for 1/4 bit mode.

Add define for EXT_EIGHTBIT to avoid using magic number.
BM_ONEBIT_MASK is no longer used, thus remove it.

This patch is untested due to lack of platform with 8-bit hardware.
However since the code is there, it's good to make the code match the document.
Signed-off-by: NAxel Lin <axel.lin@ingics.com>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

version.h inclusion is not needed as suggested by versioncheck.
Signed-off-by: NSachin Kamat <sachin.kamat@linaro.org>
Cc: Jonas Jensen <jonas.jensen@gmail.com>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

The am335x can't detect pending cirq in PM runtime suspend.
This patch reconfigures dat1 as a GPIO before going to suspend.
SDIO interrupts are detected with the GPIO, the GPIO will only wake
the module from suspend, SDIO irq detection will still happen through the
IP block.

Idea of remuxing the pins by Tony Lindgren. Code contributions from
Tony Lindgren and Balaji T K <balajitk@ti.com>
Signed-off-by: NAndreas Fenkart <afenkart@gmail.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>
Acked-by: NBalaji T K <balajitk@ti.com>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

These are predefined states of the driver model. When not present,
as if not set in the device tree, they become no-ops.
Explicitly selecting the default state is not needed since the
device core layer sets pin mux to "default" state before probe.
This is not the simplest implementation, on AM335x at least, we could
switch to idle at any point in the suspend hook, only the default state
needs to be set before writing to the irq registers or an IRQ might get
lost.
Acked-by: NBalaji T K <balajitk@ti.com>
Signed-off-by: NAndreas Fenkart <afenkart@gmail.com>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

On multicores, an sdio irq handler could be running in parallel to
runtime suspend. In the worst case it could be waiting for the spinlock
held by the runtime suspend. When runtime suspend is complete and the
functional clock (fclk) turned off, the irq handler will continue and
cause a SIGBUS on the first register access.
Acked-by: NBalaji T K <balajitk@ti.com>
Signed-off-by: NAndreas Fenkart <afenkart@gmail.com>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

To detect sdio irqs properly without spurious events,
OMAP4 needs IWE in CON and CTPL, CLKEXTFREE in HCTL to be set
Tested-by: NAndreas Fenkart <afenkart@gmail.com>
Signed-off-by: NBalaji T K <balajitk@ti.com>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

Add SDIO IRQ entries to debugfs entry. Note that PSTATE shows current
state of data lines, incl. SDIO IRQ pending
Signed-off-by: NAndreas Fenkart <afenkart@gmail.com>
Acked-by: NBalaji T K <balajitk@ti.com>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

There have been various patches floating around for enabling
the SDIO IRQ for hsmmc, but none of them ever got merged.

Probably the reason for not merging the SDIO interrupt patches
has been the lack of wake-up path for SDIO on some omaps that
has also needed remuxing the SDIO DAT1 line to a GPIO making
the patches complex.

This patch adds the minimal SDIO IRQ support to hsmmc for
omaps that do have the wake-up path. For those omaps, the
DAT1 line need to have the wake-up enable bit set, and the
wake-up interrupt is the same as for the MMC controller.

This patch has been tested on am3730 es1.2 with mwifiex
connected to MMC3 with mwifiex waking to Ethernet traffic
from off-idle mode. Note that for omaps that do not have
the SDIO wake-up path, this patch will not work for idle
modes and further patches for remuxing DAT1 to GPIO are
needed.

Based on earlier patches [1][2] by David Vrabel
<david.vrabel@csr.com>, Steve Sakoman <steve@sakoman.com>

For now, only support SDIO interrupt if we are booted with
a separate wake-irq configued via device tree. This is
because omaps need the wake-irq for idle states, and some
omaps need special quirks. And we don't want to add new
legacy mux platform init code callbacks any longer as we
are moving to DT based booting anyways.

To use it, you need to specify the wake-irq using the
interrupts-extended property.

[1] http://www.sakoman.com/cgi-bin/gitweb.cgi?p=linux.git;a=commitdiff_plain;h=010810d22f6f49ac03da4ba384969432e0320453
[2] http://comments.gmane.org/gmane.linux.kernel.mmc/20446Acked-by: NBalaji T K <balajitk@ti.com>
Signed-off-by: NAndreas Fenkart <afenkart@gmail.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

Remove the error path items that are no longer needed. The mmc card-detect
code cleans up after itself (and registers with devm) and the host error
is the same as the clock disable.
Signed-off-by: NBen Dooks <ben.dooks@codethink.co.uk>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

The pm_runtime call should implicitly disable the device once the
probe is over if there is no explicit reference gained. There is no
need to call pm_runtime_suspend() before the pm_runtime_disable()
call.
Signed-off-by: NBen Dooks <ben.dooks@codethink.co.uk>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

Use devm_request_threaded_irq() for the host interrupt handlers so we
do not have to worry about freeing them on exit or error. Tidies up the
exit path code for the driver.
Signed-off-by: NBen Dooks <ben.dooks@codethink.co.uk>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

Use the devm_clk_get() code to get the clock and allow it to be freed
automatically on release.
Signed-off-by: NBen Dooks <ben.dooks@codethink.co.uk>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

Start tidying the probe/release code by using devm_ioremap_resource() to
map the IO registers.
Signed-off-by: NBen Dooks <ben.dooks@codethink.co.uk>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

Change the initial print to show chip version and the bus rate it is
working at instead of the driver version. This is more useful information
as we already know which driver version from the kernel it is in.
Signed-off-by: NBen Dooks <ben.dooks@codethink.co.uk>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

Remove those unused ret variables to make it obvious that these function
will not return any errors in the current implementation.
Signed-off-by: NMarkus Pargmann <mpa@pengutronix.de>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

Switch the common SDHCI code over to use mmc_host's regulator pointers
and remove the ones in the sdhci_host structure.  Additionally, use the
common mmc_regulator_get_supply function to get the regulators and set
the ocr_avail mask.

This change sets the ocr_avail directly based upon the voltage ranges
supported which ensures ocr_avail is set correctly while allowing the
use of regulators that can't provide exactly 1.8v, 3.0v, or 3.3v.
Signed-off-by: NTim Kryger <tim.kryger@gmail.com>
Signed-off-by: NMarkus Mayer <markus.mayer@linaro.org>
Reviewed-by: NMatt Porter <mporter@linaro.org>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

This patch adds a fake Qualcomm ID 0x00051180 to the amba_ids, as Qualcomm
SDCC controller is pl180, but amba id registers read 0x0's.
The plan is to remove SDCC driver totally and use mmci as the main SD
controller driver for Qualcomm SOCs.
Signed-off-by: NSrinivas Kandagatla <srinivas.kandagatla@linaro.org>
Reviewed-by: NLinus Walleij <linus.walleij@linaro.org>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

MCIFIFOCNT register behaviour on Qcom chips is very different than the other
pl180 integrations. MCIFIFOCNT register contains the number of
words that are still waiting to be transferred through the FIFO. It keeps
decrementing once the host CPU reads the MCIFIFO. With the existing logic and
the MCIFIFOCNT behaviour, mmci_pio_read will loop forever, as the FIFOCNT
register will always return transfer size before reading the FIFO.

Also the data sheet states that "This register is only useful for debug
purposes and should not be used for normal operation since it does not reflect
data which may or may not be in the pipeline".

This patch implements a qcom specific get_rx_fifocnt function which is
implemented based on status register flags. Based on qcom_fifo flag in
variant data structure, the corresponding get_rx_fifocnt function is selected.
Signed-off-by: NSrinivas Kandagatla <srinivas.kandagatla@linaro.org>
Reviewed-by: NLinus Walleij <linus.walleij@linaro.org>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

On Controllers like Qcom SD card controller where cclk is mclk and mclk should
be directly controlled by the driver.

This patch adds support to control mclk directly in the driver, and also
adds explicit_mclk_control flag in variant structure giving more flexibility
to the driver.
Signed-off-by: NSrinivas Kandagatla <srinivas.kandagatla@linaro.org>
Reviewed-by: NLinus Walleij <linus.walleij@linaro.org>
[Ulf Hansson] Fixed checkpatch warning
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

Some of the controller have maximum supported frequency, This patch adds
support in variant data structure to specify such restrictions. This
gives more flexibility in calculating the f_max before passing it to
mmc-core.
Signed-off-by: NSrinivas Kandagatla <srinivas.kandagatla@linaro.org>
Reviewed-by: NLinus Walleij <linus.walleij@linaro.org>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

On some SOCs like Qcom there are explicit bits in the command register
to specify if its a data transfer command or not. So this patch adds
support to such bits in variant data, giving more flexibility to the
driver.
Signed-off-by: NSrinivas Kandagatla <srinivas.kandagatla@linaro.org>
Reviewed-by: NLinus Walleij <linus.walleij@linaro.org>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

This patch adds edge support for data and command out to variant structure
giving more flexibility to the driver to support more SOCs which have
different clock register layout.

Without this patch other new SOCs like Qcom will have to add more code to
special case them
Signed-off-by: NSrinivas Kandagatla <srinivas.kandagatla@linaro.org>
Reviewed-by: NLinus Walleij <linus.walleij@linaro.org>
[Ulf Hansson] Resolved conflict
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

This patch adds 8bit bus enable to variant structure giving more flexibility
to the driver to support more SOCs which have different clock register layout.

Without this patch other new SOCs like Qcom will have to add more code
to special case them.
Signed-off-by: NSrinivas Kandagatla <srinivas.kandagatla@linaro.org>
Reviewed-by: NLinus Walleij <linus.walleij@linaro.org>
[Ulf Hansson] Resolved conflict
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

This patch adds ddrmode mask to variant structure giving more flexibility
to the driver to support more SOCs which have different datactrl register
layout.

Without this patch datactrl register is updated with incorrect ddrmode mask,
resulting in failures on Qualcomm SD Card Controller.
Signed-off-by: NSrinivas Kandagatla <srinivas.kandagatla@linaro.org>
Reviewed-by: NLinus Walleij <linus.walleij@linaro.org>
[Ulf Hansson] Resolved conflict
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

Instance of this IP on Qualcomm's SOCs has bit different layout for datactrl
register. Bit position datactrl[16:4] hold the true block size instead of power
of 2.
Signed-off-by: NSrinivas Kandagatla <srinivas.kandagatla@linaro.org>
Reviewed-by: NLinus Walleij <linus.walleij@linaro.org>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

On Qcom SD Card controller POWER, CLKCTRL, DATACTRL and COMMAND registers
should be updated in MCLK domain, and writes to these registers must be
separated by three MCLK cycles. This resitriction is not applicable for
other registers. Any subsequent writes to these register will be ignored
until 3 MCLK have passed.

One usec delay between two CMD register writes is not sufficient in the
card identification phase where the CCLK is very low. This patch replaces
a static 1 usec delay to use mmci_reg_delay function which can provide
correct delay depending on the cclk frequency.

Without this patch the card is not detected.
Signed-off-by: NSrinivas Kandagatla <srinivas.kandagatla@linaro.org>
Reviewed-by: NLinus Walleij <linus.walleij@linaro.org>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

This patch adds a Qualcomm SD Card controller specific register variations
to header file. Qualcomm SDCC controller is pl180, with slight changes in
the register layout from standard pl180 register set.
Signed-off-by: NSrinivas Kandagatla <srinivas.kandagatla@linaro.org>
Reviewed-by: NLinus Walleij <linus.walleij@linaro.org>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

This patch replaces a constant used in calculating timeout with a proper
macro. This is make code more readable.
Signed-off-by: NSrinivas Kandagatla <srinivas.kandagatla@linaro.org>
Reviewed-by: NLinus Walleij <linus.walleij@linaro.org>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

We have a number of front-end drivers for SDHCI_PLTFM, some of them
use 'select MMC_SDHCI_PLTFM', others use 'depends on'. This is
inconsistent and confusing, and in one case has also led to a
build error because of incomplete dependencies:

warning: (MMC_SDHCI_PXAV3 && MMC_SDHCI_PXAV2 && MMC_SDHCI_BCM_KONA) selects MMC_SDHCI_PLTFM which has unmet direct dependencies (MMC && MMC_SDHCI)
drivers/built-in.o: In function `sdhci_sirf_resume':
:(.text+0xaaacb4): undefined reference to `sdhci_resume_host'
drivers/built-in.o: In function `sdhci_sirf_suspend':
:(.text+0xaaacf8): undefined reference to `sdhci_suspend_host'
drivers/built-in.o: In function `sdhci_sirf_probe':
:(.text+0xaaaf44): undefined reference to `sdhci_add_host'
:(.text+0xaaaf50): undefined reference to `sdhci_remove_host'

This changes Kconfig to use 'depends on MMC_SDHCI_PLTFM' for all these
cases, to fix the build error and make the logic more logical.
Signed-off-by: NArnd Bergmann <arnd@arndb.de>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

The MMC host driver should not select the pmic driver, since that
may have other dependencies, notably i2c in this case. It's not
clear what the exact requirement of the driver is, but to preserve
the behavior, this patch changes the 'select' into 'depends on',
meaning you now have to turn on TPS65010 explicitly and then
MMC_OMAP.

Found during randconfig build testing.
Signed-off-by: NArnd Bergmann <arnd@arndb.de>
Cc: linux-omap@vger.kernel.org
Cc: Jarkko Nikula <jarkko.nikula@bitmer.com>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

gcc correctly points out that hw_state can be used uninitially
in the mvsd_setup_data() function. This rearranges the function
to ensure it always contains a proper value.
Signed-off-by: NArnd Bergmann <arnd@arndb.de>
Cc: Nicolas Pitre <nico@fluxnic.net>
Cc: Chris Ball <chris@printf.net>
Cc: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: Andrew Lunn <andrew@lunn.ch>
Cc: linux-mmc@vger.kernel.org
Acked-by: NNicolas Pitre <nico@linaro.org>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

This avoids a build error due to the use of flush_dcache_page.

drivers/mmc/host/atmel-mci.c: In function 'atmci_read_data_pio':
drivers/mmc/host/atmel-mci.c:1870:5: error: implicit declaration of function 'flush_dcache_page' [-Werror=implicit-function-declaration]
     flush_dcache_page(sg_page(sg));
     ^
Signed-off-by: NArnd Bergmann <arnd@arndb.de>
Cc: Ludovic Desroches <ludovic.desroches@atmel.com>
Acked-by: NLudovic Desroches <ludovic.desroches@atmel.com>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

The sdhci core was refactored recently and some of those
refactorings required changes in every sdhci platform driver.
Those updates happened around the same time as when the msm
driver was merged so the refactorings missed the msm driver.
Hook in the basic library functions so that we can boot apq8074
dragonboards again instead of crashing when we try to jump to
NULL function pointers.
Reported-by: NKevin Hilman <khilman@linaro.org>
Cc: Georgi Djakov <gdjakov@mm-sol.com>
Cc: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: NStephen Boyd <sboyd@codeaurora.org>
Acked-by: NKumar Gala <galak@codeaurora.org>
Reviewed-by: NGeorgi Djakov <gdjakov@mm-sol.com>
Tested-by: NKevin Hilman <khilman@linaro.org>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

Fix a number of wrong print formats.
Signed-off-by: NGuennadi Liakhovetski <g.liakhovetski+renesas@gmail.com>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

Fix the compile error.
(Removed the card_tasklet at "mmc: sdhci: push card_tasklet into treaded irq handler")

drivers/mmc/host/sdhci-s3c.c: In function ‘sdhci_s3c_notify_change’:
drivers/mmc/host/sdhci-s3c.c:402:25: error: ‘struct sdhci_host’ has no member named ‘card_tasklet’
Signed-off-by: NJaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>
Signed-off-by: NChris Ball <chris@printf.net>

The Allwinner sunxi mmc host uses dma in bus-master mode using a built-in
designware idmac controller, which is identical to the one found in the mmc-dw
hosts. However the rest of the host is not identical to mmc-dw, it deals with
sending stop commands in hardware which makes it significantly different
from the mmc-dw devices.
Signed-off-by: NDavid Lanzendörfer <david.lanzendoerfer@o2s.ch>
[hdegoede@redhat.com: various cleanups and fixes]
Signed-off-by: NHans de Goede <hdegoede@redhat.com>
Acked-by: NMaxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: NArnd Bergmann <arnd@arndb.de>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>
Acked-by: NChris Ball <chris@printf.net>
Signed-off-by: NMike Turquette <mturquette@linaro.org>

This patch adds a driver for the Renesas usdhi6rol0 SD/SDIO host controller
in both PIO and DMA modes.
Signed-off-by: NGuennadi Liakhovetski <g.liakhovetski+renesas@gmail.com>
Signed-off-by: NChris Ball <chris@printf.net>

Remove the option to provide DMA configuration as platform data,
enforce it through DT.
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>
Cc: Russell King <linux@arm.linux.org.uk>
Cc: Roland Stigge <stigge@antcom.de>
Acked-by: NArnd Bergmann <arnd@arndb.de>

The commit below introduced compile errors, let's fix them.
mmc: sdhci-of-esdhc: remove platform_suspend/platform_resume callbacks

Cc: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>
Signed-off-by: NChris Ball <chris@printf.net>