Add support for clock gating of the SNVS peripheral.
Signed-off-by: NSanchayan Maity <maitysanchayan@gmail.com>
Signed-off-by: NShawn Guo <shawn.guo@linaro.org>

So far, the required PLL's (PLL1/PLL2/PLL5) have been initialized
by boot loader and the kernel code defined fixed rates according
to those default configurations. Beginning with the USB PLL7 the
code started to initialize the PLL's itself (using imx_clk_pllv3).

However, since commit dc4805c2
(ARM: imx: remove ENABLE and BYPASS bits from clk-pllv3 driver)
imx_clk_pllv3 no longer takes care of the ENABLE and BYPASS bits,
hence the USB PLL were not configured correctly anymore.

This patch not only fixes those USB PLL's, but also makes use of
the imx_clk_pllv3 for all PLL's and alignes the code with the PLL
support of the i.MX6 series.
Signed-off-by: NStefan Agner <stefan@agner.ch>
Signed-off-by: NShawn Guo <shawn.guo@linaro.org>

This commit adds PLL7 which is required for USBPHY1. It also adds
the USB PHY and USB Controller clocks and the gates to enable them.
Acked-by: NJingchang Lu <jingchang.lu@freescale.com>
Signed-off-by: NStefan Agner <stefan@agner.ch>
Signed-off-by: NShawn Guo <shawn.guo@freescale.com>

Extend the clock control for FlexCAN with the second gate which
enable the clocks in the Clock Divider (CCM_CSCDR2) register too.
Signed-off-by: NStefan Agner <stefan@agner.ch>
Signed-off-by: NShawn Guo <shawn.guo@freescale.com>

Signed-off-by: NJingchang Lu <b35083@freescale.com>
Signed-off-by: NShawn Guo <shawn.guo@linaro.org>

The fec/enet driver calculates MDC rate with the formula below.

  ref_freq / ((MII_SPEED + 1) x 2)

The ref_freq here is the fec internal module clock, which is missing
from clk-vf610 clock driver right now.  And clk-vf610 driver mistakenly
supplies RMII clock (50 MHz) as the source to fec.  This results in the
situation that fec driver gets ref_freq as 50 MHz, while physically it
runs at 66 MHz (fec module clock physically sources from ipg which runs
at 66 MHz).  That's why software expects MDC runs at 2.5 MHz, while the
measurement tells it runs at 3.3 MHz.  And this causes the PHY KSZ8041
keeps swithing between Full and Half mode as below.

  libphy: 400d0000.etherne:00 - Link is Up - 100/Full
  libphy: 400d0000.etherne:00 - Link is Up - 100/Half
  libphy: 400d0000.etherne:00 - Link is Up - 100/Full
  libphy: 400d0000.etherne:00 - Link is Up - 100/Half
  libphy: 400d0000.etherne:00 - Link is Up - 100/Full
  libphy: 400d0000.etherne:00 - Link is Up - 100/Half

Add the missing module clock for ENET0 and ENET1, and correct the clock
supplying in device tree to fix above issue.

Thanks to Alison Wang <b18965@freescale.com> for debugging the issue.
Signed-off-by: NShawn Guo <shawn.guo@linaro.org>

Add clock support for Vybrid VF610. It uses dtc macro support to
define all clock IDs in vf610-clock.h to keep clock IDs coherence
between kernel and DT.
Signed-off-by: NJingchang Lu <b35083@freescale.com>
Signed-off-by: NShawn Guo <shawn.guo@linaro.org>