Skip to content

cloud-kernel
cloud-kernel

openanolis / cloud-kernel
大约 1 年 前同步成功

通知 155
Star 36
Fork 7
cloud-kernel
cloud-kernel

体验新版 GitCode，发现更多精彩内容 >>

切换分支/标签
  1. 31 1月, 2011 1 次提交
  3. 14 1月, 2011 1 次提交
  5. 14 8月, 2010 1 次提交
  7. 13 8月, 2010 1 次提交
  9. 27 7月, 2010 3 次提交
  11. 13 4月, 2010 1 次提交
    • J
      time: Remove xtime_cache · 6a867a39
      由 John Stultz 提交于 
      With the earlier logarithmic time accumulation patch, xtime will now
always be within one "tick" of the current time, instead of possibly
half a second off.

This removes the need for the xtime_cache value, which always stored the
time at the last interrupt, so this patch cleans that up removing the
xtime_cache related code.

This patch also addresses an issue with an earlier version of this change,
where xtime_cache was normalizing xtime, which could in some cases be
not valid (ie: tv_nsec == NSEC_PER_SEC). This is fixed by handling
the edge case in update_wall_time().
Signed-off-by: NJohn Stultz <johnstul@us.ibm.com>
Cc: Petr Titěra <P.Titera@century.cz>
LKML-Reference: <1270589451-30773-1-git-send-email-johnstul@us.ibm.com>
Signed-off-by: NThomas Gleixner <tglx@linutronix.de>
      6a867a39
  13. 14 11月, 2009 1 次提交
    • J
      nohz: Prevent clocksource wrapping during idle · 98962465
      由 Jon Hunter 提交于 
      The dynamic tick allows the kernel to sleep for periods longer than a
single tick, but it does not limit the sleep time currently. In the
worst case the kernel could sleep longer than the wrap around time of
the time keeping clock source which would result in losing track of
time.

Prevent this by limiting it to the safe maximum sleep time of the
current time keeping clock source. The value is calculated when the
clock source is registered.

[ tglx: simplified the code a bit and massaged the commit msg ]
Signed-off-by: NJon Hunter <jon-hunter@ti.com>
Cc: John Stultz <johnstul@us.ibm.com>
LKML-Reference: <1250617512-23567-2-git-send-email-jon-hunter@ti.com>
Signed-off-by: NThomas Gleixner <tglx@linutronix.de>
      98962465
  15. 24 9月, 2009 1 次提交
    • Z
      time: add function to convert between calendar time and broken-down time for universal use · 57f1f087
      由 Zhaolei 提交于 
      There are many similar code in kernel for one object: convert time between
calendar time and broken-down time.

Here is some source I found:
  fs/ncpfs/dir.c
  fs/smbfs/proc.c
  fs/fat/misc.c
  fs/udf/udftime.c
  fs/cifs/netmisc.c
  net/netfilter/xt_time.c
  drivers/scsi/ips.c
  drivers/input/misc/hp_sdc_rtc.c
  drivers/rtc/rtc-lib.c
  arch/ia64/hp/sim/boot/fw-emu.c
  arch/m68k/mac/misc.c
  arch/powerpc/kernel/time.c
  arch/parisc/include/asm/rtc.h
  ...

We can make a common function for this type of conversion, At least we
can get following benefit:

1: Make kernel simple and unify
2: Easy to fix bug in converting code
3: Reduce clone of code in future
   For example, I'm trying to make ftrace display walltime,
   this patch will make me easy.

This code is based on code from glibc-2.6
Signed-off-by: NZhao Lei <zhaolei@cn.fujitsu.com>
Cc: OGAWA Hirofumi <hirofumi@mail.parknet.co.jp>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Pavel Machek <pavel@ucw.cz>
Cc: Andi Kleen <andi@firstfloor.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>
      57f1f087
  17. 15 9月, 2009 1 次提交
    • T
      time: Prevent 32 bit overflow with set_normalized_timespec() · 12e09337
      由 Thomas Gleixner 提交于 
      set_normalized_timespec() nsec argument is of type long. The recent
timekeeping changes of ktime_get_ts() feed 

	ts->tv_nsec + tomono.tv_nsec + nsecs

to set_normalized_timespec(). On 32 bit machines that sum can be
larger than (1 << 31) and therefor result in a negative value which
screws up the result completely.

Make the nsec argument of set_normalized_timespec() s64 to fix the
problem at hand. This also prevents similar problems for future users
of set_normalized_timespec().
Signed-off-by: NThomas Gleixner <tglx@linutronix.de>
Tested-by: NCarsten Emde <carsten.emde@osadl.org>
LKML-Reference: <new-submission>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: John Stultz <johnstul@us.ibm.com>
      12e09337
  19. 22 8月, 2009 1 次提交
    • J
      time: Introduce CLOCK_REALTIME_COARSE · da15cfda
      由 john stultz 提交于 
      After talking with some application writers who want very fast, but not
fine-grained timestamps, I decided to try to implement new clock_ids
to clock_gettime(): CLOCK_REALTIME_COARSE and CLOCK_MONOTONIC_COARSE
which returns the time at the last tick. This is very fast as we don't
have to access any hardware (which can be very painful if you're using
something like the acpi_pm clocksource), and we can even use the vdso
clock_gettime() method to avoid the syscall. The only trade off is you
only get low-res tick grained time resolution.

This isn't a new idea, I know Ingo has a patch in the -rt tree that made
the vsyscall gettimeofday() return coarse grained time when the
vsyscall64 sysctrl was set to 2. However this affects all applications
on a system.

With this method, applications can choose the proper speed/granularity
trade-off for themselves.
Signed-off-by: NJohn Stultz <johnstul@us.ibm.com>
Cc: Andi Kleen <andi@firstfloor.org>
Cc: nikolag@ca.ibm.com
Cc: Darren Hart <dvhltc@us.ibm.com>
Cc: arjan@infradead.org
Cc: jonathan@jonmasters.org
LKML-Reference: <1250734414.6897.5.camel@localhost.localdomain>
Signed-off-by: NThomas Gleixner <tglx@linutronix.de>
      da15cfda
  21. 15 8月, 2009 3 次提交
  23. 02 5月, 2009 1 次提交
  25. 27 3月, 2009 1 次提交
    • A
      make exported headers use strict posix types · 85efde6f
      由 Arnd Bergmann 提交于 
      A number of standard posix types are used in exported headers, which
is not allowed if __STRICT_KERNEL_NAMES is defined. In order to
get rid of the non-__STRICT_KERNEL_NAMES part and to make sane headers
the default, we have to change them all to safe types.

There are also still some leftovers in reiserfs_fs.h, elfcore.h
and coda.h, but these files have not compiled in user space for
a long time.

This leaves out the various integer types ({u_,u,}int{8,16,32,64}_t),
which we take care of separately.
Signed-off-by: NArnd Bergmann <arnd@arndb.de>
Acked-by: NMauro Carvalho Chehab <mchehab@redhat.com>
Cc: David Airlie <airlied@linux.ie>
Cc: Arnaldo Carvalho de Melo <acme@ghostprotocols.net>
Cc: YOSHIFUJI Hideaki <yoshfuji@linux-ipv6.org>
Cc: netdev@vger.kernel.org
Cc: linux-ppp@vger.kernel.org
Cc: Jaroslav Kysela <perex@perex.cz>
Cc: Takashi Iwai <tiwai@suse.de>
Cc: David Woodhouse <dwmw2@infradead.org>
Signed-off-by: NH. Peter Anvin <hpa@linux.intel.com>
Signed-off-by: NIngo Molnar <mingo@elte.hu>
      85efde6f
  27. 31 12月, 2008 1 次提交
    • T
      sched_clock: prevent scd->clock from moving backwards, take #2 · 1c5745aa
      由 Thomas Gleixner 提交于 
      Redo:

  5b7dba4f: sched_clock: prevent scd->clock from moving backwards

which had to be reverted due to s2ram hangs:

  ca7e716c: Revert "sched_clock: prevent scd->clock from moving backwards"

... this time with resume restoring GTOD later in the sequence
taken into account as well.

The "timekeeping_suspended" flag is not very nice but we cannot call into
GTOD before it has been properly resumed and the scheduler will run very
early in the resume sequence.

Cc: <stable@kernel.org>
Signed-off-by: NIngo Molnar <mingo@elte.hu>
      1c5745aa
  29. 17 10月, 2008 1 次提交
    • C
      compat: generic compat get/settimeofday · b418da16
      由 Christoph Hellwig 提交于 
      Nothing arch specific in get/settimeofday.  The details of the timeval
conversion varied a little from arch to arch, but all with the same
results.

Also add an extern declaration for sys_tz to linux/time.h because externs
in .c files are fowned upon.  I'll kill the externs in various other files
in a sparate patch.

[akpm@linux-foundation.org: coding-style fixes]
Signed-off-by: NChristoph Hellwig <hch@lst.de>
Acked-by: David S. Miller <davem@davemloft.net> [ sparc bits ]
Cc: "Luck, Tony" <tony.luck@intel.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Acked-by: NKyle McMartin <kyle@mcmartin.ca>
Cc: Matthew Wilcox <matthew@wil.cx>
Cc: Grant Grundler <grundler@parisc-linux.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>
      b418da16
  31. 14 9月, 2008 1 次提交
    • F
      timers: fix itimer/many thread hang · f06febc9
      由 Frank Mayhar 提交于 
      Overview

This patch reworks the handling of POSIX CPU timers, including the
ITIMER_PROF, ITIMER_VIRT timers and rlimit handling.  It was put together
with the help of Roland McGrath, the owner and original writer of this code.

The problem we ran into, and the reason for this rework, has to do with using
a profiling timer in a process with a large number of threads.  It appears
that the performance of the old implementation of run_posix_cpu_timers() was
at least O(n*3) (where "n" is the number of threads in a process) or worse.
Everything is fine with an increasing number of threads until the time taken
for that routine to run becomes the same as or greater than the tick time, at
which point things degrade rather quickly.

This patch fixes bug 9906, "Weird hang with NPTL and SIGPROF."

Code Changes

This rework corrects the implementation of run_posix_cpu_timers() to make it
run in constant time for a particular machine.  (Performance may vary between
one machine and another depending upon whether the kernel is built as single-
or multiprocessor and, in the latter case, depending upon the number of
running processors.)  To do this, at each tick we now update fields in
signal_struct as well as task_struct.  The run_posix_cpu_timers() function
uses those fields to make its decisions.

We define a new structure, "task_cputime," to contain user, system and
scheduler times and use these in appropriate places:

struct task_cputime {
	cputime_t utime;
	cputime_t stime;
	unsigned long long sum_exec_runtime;
};

This is included in the structure "thread_group_cputime," which is a new
substructure of signal_struct and which varies for uniprocessor versus
multiprocessor kernels.  For uniprocessor kernels, it uses "task_cputime" as
a simple substructure, while for multiprocessor kernels it is a pointer:

struct thread_group_cputime {
	struct task_cputime totals;
};

struct thread_group_cputime {
	struct task_cputime *totals;
};

We also add a new task_cputime substructure directly to signal_struct, to
cache the earliest expiration of process-wide timers, and task_cputime also
replaces the it_*_expires fields of task_struct (used for earliest expiration
of thread timers).  The "thread_group_cputime" structure contains process-wide
timers that are updated via account_user_time() and friends.  In the non-SMP
case the structure is a simple aggregator; unfortunately in the SMP case that
simplicity was not achievable due to cache-line contention between CPUs (in
one measured case performance was actually _worse_ on a 16-cpu system than
the same test on a 4-cpu system, due to this contention).  For SMP, the
thread_group_cputime counters are maintained as a per-cpu structure allocated
using alloc_percpu().  The timer functions update only the timer field in
the structure corresponding to the running CPU, obtained using per_cpu_ptr().

We define a set of inline functions in sched.h that we use to maintain the
thread_group_cputime structure and hide the differences between UP and SMP
implementations from the rest of the kernel.  The thread_group_cputime_init()
function initializes the thread_group_cputime structure for the given task.
The thread_group_cputime_alloc() is a no-op for UP; for SMP it calls the
out-of-line function thread_group_cputime_alloc_smp() to allocate and fill
in the per-cpu structures and fields.  The thread_group_cputime_free()
function, also a no-op for UP, in SMP frees the per-cpu structures.  The
thread_group_cputime_clone_thread() function (also a UP no-op) for SMP calls
thread_group_cputime_alloc() if the per-cpu structures haven't yet been
allocated.  The thread_group_cputime() function fills the task_cputime
structure it is passed with the contents of the thread_group_cputime fields;
in UP it's that simple but in SMP it must also safely check that tsk->signal
is non-NULL (if it is it just uses the appropriate fields of task_struct) and,
if so, sums the per-cpu values for each online CPU.  Finally, the three
functions account_group_user_time(), account_group_system_time() and
account_group_exec_runtime() are used by timer functions to update the
respective fields of the thread_group_cputime structure.

Non-SMP operation is trivial and will not be mentioned further.

The per-cpu structure is always allocated when a task creates its first new
thread, via a call to thread_group_cputime_clone_thread() from copy_signal().
It is freed at process exit via a call to thread_group_cputime_free() from
cleanup_signal().

All functions that formerly summed utime/stime/sum_sched_runtime values from
from all threads in the thread group now use thread_group_cputime() to
snapshot the values in the thread_group_cputime structure or the values in
the task structure itself if the per-cpu structure hasn't been allocated.

Finally, the code in kernel/posix-cpu-timers.c has changed quite a bit.
The run_posix_cpu_timers() function has been split into a fast path and a
slow path; the former safely checks whether there are any expired thread
timers and, if not, just returns, while the slow path does the heavy lifting.
With the dedicated thread group fields, timers are no longer "rebalanced" and
the process_timer_rebalance() function and related code has gone away.  All
summing loops are gone and all code that used them now uses the
thread_group_cputime() inline.  When process-wide timers are set, the new
task_cputime structure in signal_struct is used to cache the earliest
expiration; this is checked in the fast path.

Performance

The fix appears not to add significant overhead to existing operations.  It
generally performs the same as the current code except in two cases, one in
which it performs slightly worse (Case 5 below) and one in which it performs
very significantly better (Case 2 below).  Overall it's a wash except in those
two cases.

I've since done somewhat more involved testing on a dual-core Opteron system.

Case 1: With no itimer running, for a test with 100,000 threads, the fixed
	kernel took 1428.5 seconds, 513 seconds more than the unfixed system,
	all of which was spent in the system.  There were twice as many
	voluntary context switches with the fix as without it.

Case 2: With an itimer running at .01 second ticks and 4000 threads (the most
	an unmodified kernel can handle), the fixed kernel ran the test in
	eight percent of the time (5.8 seconds as opposed to 70 seconds) and
	had better tick accuracy (.012 seconds per tick as opposed to .023
	seconds per tick).

Case 3: A 4000-thread test with an initial timer tick of .01 second and an
	interval of 10,000 seconds (i.e. a timer that ticks only once) had
	very nearly the same performance in both cases:  6.3 seconds elapsed
	for the fixed kernel versus 5.5 seconds for the unfixed kernel.

With fewer threads (eight in these tests), the Case 1 test ran in essentially
the same time on both the modified and unmodified kernels (5.2 seconds versus
5.8 seconds).  The Case 2 test ran in about the same time as well, 5.9 seconds
versus 5.4 seconds but again with much better tick accuracy, .013 seconds per
tick versus .025 seconds per tick for the unmodified kernel.

Since the fix affected the rlimit code, I also tested soft and hard CPU limits.

Case 4: With a hard CPU limit of 20 seconds and eight threads (and an itimer
	running), the modified kernel was very slightly favored in that while
	it killed the process in 19.997 seconds of CPU time (5.002 seconds of
	wall time), only .003 seconds of that was system time, the rest was
	user time.  The unmodified kernel killed the process in 20.001 seconds
	of CPU (5.014 seconds of wall time) of which .016 seconds was system
	time.  Really, though, the results were too close to call.  The results
	were essentially the same with no itimer running.

Case 5: With a soft limit of 20 seconds and a hard limit of 2000 seconds
	(where the hard limit would never be reached) and an itimer running,
	the modified kernel exhibited worse tick accuracy than the unmodified
	kernel: .050 seconds/tick versus .028 seconds/tick.  Otherwise,
	performance was almost indistinguishable.  With no itimer running this
	test exhibited virtually identical behavior and times in both cases.

In times past I did some limited performance testing.  those results are below.

On a four-cpu Opteron system without this fix, a sixteen-thread test executed
in 3569.991 seconds, of which user was 3568.435s and system was 1.556s.  On
the same system with the fix, user and elapsed time were about the same, but
system time dropped to 0.007 seconds.  Performance with eight, four and one
thread were comparable.  Interestingly, the timer ticks with the fix seemed
more accurate:  The sixteen-thread test with the fix received 149543 ticks
for 0.024 seconds per tick, while the same test without the fix received 58720
for 0.061 seconds per tick.  Both cases were configured for an interval of
0.01 seconds.  Again, the other tests were comparable.  Each thread in this
test computed the primes up to 25,000,000.

I also did a test with a large number of threads, 100,000 threads, which is
impossible without the fix.  In this case each thread computed the primes only
up to 10,000 (to make the runtime manageable).  System time dominated, at
1546.968 seconds out of a total 2176.906 seconds (giving a user time of
629.938s).  It received 147651 ticks for 0.015 seconds per tick, still quite
accurate.  There is obviously no comparable test without the fix.
Signed-off-by: NFrank Mayhar <fmayhar@google.com>
Cc: Roland McGrath <roland@redhat.com>
Cc: Alexey Dobriyan <adobriyan@gmail.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: NIngo Molnar <mingo@elte.hu>
      f06febc9
  33. 06 9月, 2008 1 次提交
  35. 21 8月, 2008 1 次提交
    • J
      clocksource: introduce CLOCK_MONOTONIC_RAW · 2d42244a
      由 John Stultz 提交于 
      In talking with Josip Loncaric, and his work on clock synchronization (see
btime.sf.net), he mentioned that for really close synchronization, it is
useful to have access to "hardware time", that is a notion of time that is
not in any way adjusted by the clock slewing done to keep close time sync.

Part of the issue is if we are using the kernel's ntp adjusted
representation of time in order to measure how we should correct time, we
can run into what Paul McKenney aptly described as "Painting a road using
the lines we're painting as the guide".

I had been thinking of a similar problem, and was trying to come up with a
way to give users access to a purely hardware based time representation
that avoided users having to know the underlying frequency and mask values
needed to deal with the wide variety of possible underlying hardware
counters.

My solution is to introduce CLOCK_MONOTONIC_RAW.  This exposes a
nanosecond based time value, that increments starting at bootup and has no
frequency adjustments made to it what so ever.

The time is accessed from userspace via the posix_clock_gettime() syscall,
passing CLOCK_MONOTONIC_RAW as the clock_id.
Signed-off-by: NJohn Stultz <johnstul@us.ibm.com>
Signed-off-by: NRoman Zippel <zippel@linux-m68k.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NIngo Molnar <mingo@elte.hu>
      2d42244a
  37. 12 6月, 2008 2 次提交
    • J
      always_inline timespec_add_ns · 9412e286
      由 Jeremy Fitzhardinge 提交于 
      timespec_add_ns is used from the x86-64 vdso, which cannot call out to
other kernel code.  Make sure that timespec_add_ns is always inlined
(and only uses always_inlined functions) to make sure there are no
unexpected calls.
Signed-off-by: NJeremy Fitzhardinge <jeremy.fitzhardinge@citrix.com>
Signed-off-by: NIngo Molnar <mingo@elte.hu>
      9412e286
    • J
      common implementation of iterative div/mod · f595ec96
      由 Jeremy Fitzhardinge 提交于 
      We have a few instances of the open-coded iterative div/mod loop, used
when we don't expcet the dividend to be much bigger than the divisor.
Unfortunately modern gcc's have the tendency to strength "reduce" this
into a full mod operation, which isn't necessarily any faster, and
even if it were, doesn't exist if gcc implements it in libgcc.

The workaround is to put a dummy asm statement in the loop to prevent
gcc from performing the transformation.

This patch creates a single implementation of this loop, and uses it
to replace the open-coded versions I know about.
Signed-off-by: NJeremy Fitzhardinge <jeremy.fitzhardinge@citrix.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: john stultz <johnstul@us.ibm.com>
Cc: Segher Boessenkool <segher@kernel.crashing.org>
Cc: Christian Kujau <lists@nerdbynature.de>
Cc: Robert Hancock <hancockr@shaw.ca>
Signed-off-by: NIngo Molnar <mingo@elte.hu>
      f595ec96
  39. 09 3月, 2008 1 次提交
  41. 09 2月, 2008 1 次提交
  43. 02 2月, 2008 1 次提交
  45. 17 10月, 2007 1 次提交
  47. 26 7月, 2007 2 次提交
    • J
      Cache xtime every call to update_wall_time · 17c38b74
      由 john stultz 提交于 
      This avoids xtime lag seen with dynticks, because while 'xtime' itself
is still not updated often, we keep a 'xtime_cache' variable around that
contains the approximate real-time that _is_ updated each time we do a
'update_wall_time()', and is thus never off by more than one tick.

IOW, this restores the original semantics for 'xtime' users, as long as
you use the proper abstraction functions (ie 'current_kernel_time()' or
'get_seconds()' depending on whether you want a timespec or just the
seconds field).

[ Updated Patch.  As penance for my sins I've also yanked another #ifdef
  that was added to avoid the xtime lag w/ hrtimers.  ]
Signed-off-by: NJohn Stultz <johnstul@us.ibm.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>
      17c38b74
    • J
      Cleanup non-arch xtime uses, use get_seconds() or current_kernel_time(). · 2c6b47de
      由 john stultz 提交于 
      This avoids use of the kernel-internal "xtime" variable directly outside
of the actual time-related functions.  Instead, use the helper functions
that we already have available to us.

This doesn't actually change any behaviour, but this will allow us to
fix the fact that "xtime" isn't updated very often with CONFIG_NO_HZ
(because much of the realtime information is maintained as separate
offsets to 'xtime'), which has caused interfaces that use xtime directly
to get a time that is out of sync with the real-time clock by up to a
third of a second or so.
Signed-off-by: NJohn Stultz <johnstul@us.ibm.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>
      2c6b47de
  49. 22 7月, 2007 1 次提交
  51. 18 7月, 2007 1 次提交
  53. 17 7月, 2007 1 次提交
    • T
      Introduce boot based time · 7c3f1a57
      由 Tomas Janousek 提交于 
      The commits

  411187fb (GTOD: persistent clock support)
  c1d370e1 (i386: use GTOD persistent clock
    support)

changed the monotonic time so that it no longer jumps after resume, but it's
not possible to use it for boot time and process start time calculations then.
 Also, the uptime no longer increases during suspend.

I add a variable to track the wall_to_monotonic changes, a function to get the
real boot time and a function to get the boot based time from the monotonic
one.

[akpm@linux-foundation.org: remove exports, add comment]
Signed-off-by: NTomas Janousek <tjanouse@redhat.com>
Cc: Tomas Smetana <tsmetana@redhat.com>
Cc: John Stultz <johnstul@us.ibm.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Ingo Molnar <mingo@elte.hu>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>
      7c3f1a57
  55. 09 5月, 2007 2 次提交
    • U
      utimensat implementation · 1c710c89
      由 Ulrich Drepper 提交于 
      Implement utimensat(2) which is an extension to futimesat(2) in that it

a) supports nano-second resolution for the timestamps
b) allows to selectively ignore the atime/mtime value
c) allows to selectively use the current time for either atime or mtime
d) supports changing the atime/mtime of a symlink itself along the lines
   of the BSD lutimes(3) functions

For this change the internally used do_utimes() functions was changed to
accept a timespec time value and an additional flags parameter.

Additionally the sys_utime function was changed to match compat_sys_utime
which already use do_utimes instead of duplicating the work.

Also, the completely missing futimensat() functionality is added.  We have
such a function in glibc but we have to resort to using /proc/self/fd/* which
not everybody likes (chroot etc).

Test application (the syscall number will need per-arch editing):

#include <errno.h>
#include <fcntl.h>
#include <time.h>
#include <sys/time.h>
#include <stddef.h>
#include <syscall.h>

#define __NR_utimensat 280

#define UTIME_NOW       ((1l << 30) - 1l)
#define UTIME_OMIT      ((1l << 30) - 2l)

int
main(void)
{
  int status = 0;

  int fd = open("ttt", O_RDWR|O_CREAT|O_EXCL, 0666);
  if (fd == -1)
    error (1, errno, "failed to create test file \"ttt\"");

  struct stat64 st1;
  if (fstat64 (fd, &st1) != 0)
    error (1, errno, "fstat failed");

  struct timespec t[2];
  t[0].tv_sec = 0;
  t[0].tv_nsec = 0;
  t[1].tv_sec = 0;
  t[1].tv_nsec = 0;
  if (syscall(__NR_utimensat, AT_FDCWD, "ttt", t, 0) != 0)
    error (1, errno, "utimensat failed");

  struct stat64 st2;
  if (fstat64 (fd, &st2) != 0)
    error (1, errno, "fstat failed");

  if (st2.st_atim.tv_sec != 0 || st2.st_atim.tv_nsec != 0)
    {
      puts ("atim not reset to zero");
      status = 1;
    }
  if (st2.st_mtim.tv_sec != 0 || st2.st_mtim.tv_nsec != 0)
    {
      puts ("mtim not reset to zero");
      status = 1;
    }
  if (status != 0)
    goto out;

  t[0] = st1.st_atim;
  t[1].tv_sec = 0;
  t[1].tv_nsec = UTIME_OMIT;
  if (syscall(__NR_utimensat, AT_FDCWD, "ttt", t, 0) != 0)
    error (1, errno, "utimensat failed");

  if (fstat64 (fd, &st2) != 0)
    error (1, errno, "fstat failed");

  if (st2.st_atim.tv_sec != st1.st_atim.tv_sec
      || st2.st_atim.tv_nsec != st1.st_atim.tv_nsec)
    {
      puts ("atim not set");
      status = 1;
    }
  if (st2.st_mtim.tv_sec != 0 || st2.st_mtim.tv_nsec != 0)
    {
      puts ("mtim changed from zero");
      status = 1;
    }
  if (status != 0)
    goto out;

  t[0].tv_sec = 0;
  t[0].tv_nsec = UTIME_OMIT;
  t[1] = st1.st_mtim;
  if (syscall(__NR_utimensat, AT_FDCWD, "ttt", t, 0) != 0)
    error (1, errno, "utimensat failed");

  if (fstat64 (fd, &st2) != 0)
    error (1, errno, "fstat failed");

  if (st2.st_atim.tv_sec != st1.st_atim.tv_sec
      || st2.st_atim.tv_nsec != st1.st_atim.tv_nsec)
    {
      puts ("mtim changed from original time");
      status = 1;
    }
  if (st2.st_mtim.tv_sec != st1.st_mtim.tv_sec
      || st2.st_mtim.tv_nsec != st1.st_mtim.tv_nsec)
    {
      puts ("mtim not set");
      status = 1;
    }
  if (status != 0)
    goto out;

  sleep (2);

  t[0].tv_sec = 0;
  t[0].tv_nsec = UTIME_NOW;
  t[1].tv_sec = 0;
  t[1].tv_nsec = UTIME_NOW;
  if (syscall(__NR_utimensat, AT_FDCWD, "ttt", t, 0) != 0)
    error (1, errno, "utimensat failed");

  if (fstat64 (fd, &st2) != 0)
    error (1, errno, "fstat failed");

  struct timeval tv;
  gettimeofday(&tv,NULL);

  if (st2.st_atim.tv_sec <= st1.st_atim.tv_sec
      || st2.st_atim.tv_sec > tv.tv_sec)
    {
      puts ("atim not set to NOW");
      status = 1;
    }
  if (st2.st_mtim.tv_sec <= st1.st_mtim.tv_sec
      || st2.st_mtim.tv_sec > tv.tv_sec)
    {
      puts ("mtim not set to NOW");
      status = 1;
    }

  if (symlink ("ttt", "tttsym") != 0)
    error (1, errno, "cannot create symlink");

  t[0].tv_sec = 0;
  t[0].tv_nsec = 0;
  t[1].tv_sec = 0;
  t[1].tv_nsec = 0;
  if (syscall(__NR_utimensat, AT_FDCWD, "tttsym", t, AT_SYMLINK_NOFOLLOW) != 0)
    error (1, errno, "utimensat failed");

  if (lstat64 ("tttsym", &st2) != 0)
    error (1, errno, "lstat failed");

  if (st2.st_atim.tv_sec != 0 || st2.st_atim.tv_nsec != 0)
    {
      puts ("symlink atim not reset to zero");
      status = 1;
    }
  if (st2.st_mtim.tv_sec != 0 || st2.st_mtim.tv_nsec != 0)
    {
      puts ("symlink mtim not reset to zero");
      status = 1;
    }
  if (status != 0)
    goto out;

  t[0].tv_sec = 1;
  t[0].tv_nsec = 0;
  t[1].tv_sec = 1;
  t[1].tv_nsec = 0;
  if (syscall(__NR_utimensat, fd, NULL, t, 0) != 0)
    error (1, errno, "utimensat failed");

  if (fstat64 (fd, &st2) != 0)
    error (1, errno, "fstat failed");

  if (st2.st_atim.tv_sec != 1 || st2.st_atim.tv_nsec != 0)
    {
      puts ("atim not reset to one");
      status = 1;
    }
  if (st2.st_mtim.tv_sec != 1 || st2.st_mtim.tv_nsec != 0)
    {
      puts ("mtim not reset to one");
      status = 1;
    }

  if (status == 0)
     puts ("all OK");

 out:
  close (fd);
  unlink ("ttt");
  unlink ("tttsym");

  return status;
}

[akpm@linux-foundation.org: add missing i386 syscall table entry]
Signed-off-by: NUlrich Drepper <drepper@redhat.com>
Cc: Alexey Dobriyan <adobriyan@openvz.org>
Cc: Michael Kerrisk <mtk-manpages@gmx.net>
Cc: <linux-arch@vger.kernel.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>
      1c710c89
    • J
      Move timekeeping code to timekeeping.c · 8524070b
      由 john stultz 提交于 
      Move the timekeeping code out of kernel/timer.c and into
kernel/time/timekeeping.c.  I made no cleanups or other changes in transit.

[akpm@linux-foundation.org: build fix]
Signed-off-by: NJohn Stultz <johnstul@us.ibm.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>
      8524070b
  57. 17 2月, 2007 1 次提交
  59. 13 2月, 2007 1 次提交
    • E
      [PATCH] x86-64: get rid of ARCH_HAVE_XTIME_LOCK · 5809f9d4
      由 Eric Dumazet 提交于 
      ARCH_HAVE_XTIME_LOCK is used by x86_64 arch .  This arch needs to place a
read only copy of xtime_lock into vsyscall page.  This read only copy is
named __xtime_lock, and xtime_lock is defined in
arch/x86_64/kernel/vmlinux.lds.S as an alias.  So the declaration of
xtime_lock in kernel/timer.c was guarded by ARCH_HAVE_XTIME_LOCK define,
defined to true on x86_64.

We can get same result with _attribute__((weak)) in the declaration. linker
should do the job.
Signed-off-by: NEric Dumazet <dada1@cosmosbay.com>
Signed-off-by: NAndi Kleen <ak@suse.de>
Cc: Andi Kleen <ak@suse.de>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
      5809f9d4
  61. 12 2月, 2007 1 次提交
  63. 15 7月, 2006 1 次提交
  65. 27 6月, 2006 1 次提交