This patch adds a generic infrastructure for policy-based dequeueing of
TX packets and provides two policies:
 * a simple FIFO policy (which is the default) and
 * a priority based policy (set via socket options).
Both policies honour the tx_qlen sysctl for the maximum size of the write
queue (can be overridden via socket options).

The priority policy uses skb->priority internally to assign an u32 priority
identifier, using the same ranking as SO_PRIORITY. The skb->priority field
is set to 0 when the packet leaves DCCP. The priority is supplied as ancillary
data using cmsg(3), the patch also provides the requisite parsing routines.
Signed-off-by: NTomasz Grobelny <tomasz@grobelny.oswiecenia.net>
Signed-off-by: NGerrit Renker <gerrit@erg.abdn.ac.uk>

This completes the implementation of a circular buffer for Ack Vectors, by
extending the current (linear array-based) implementation.  The changes are:

 (a) An `overflow' flag to deal with the case of overflow. As before, dynamic
     growth of the buffer will not be supported; but code will be added to deal
     robustly with overflowing Ack Vector buffers.

 (b) A `tail_seqno' field. When naively implementing the algorithm of Appendix A
     in RFC 4340, problems arise whenever subsequent Ack Vector records overlap,
     which can bring the entire run length calculation completely out of synch.
     (This is documented on http://www.erg.abdn.ac.uk/users/gerrit/dccp/notes/\
                                             ack_vectors/tracking_tail_ackno/ .)
 (c) The buffer length is now computed dynamically (i.e. current fill level),
     as the span between head to tail.

As a result, dccp_ackvec_pending() is now simpler - the #ifdef is no longer
necessary since buf_empty is always true when IP_DCCP_ACKVEC is not configured.
Signed-off-by: NGerrit Renker <gerrit@erg.abdn.ac.uk>

This extends the existing wait-for-ccid routine so that it may be used with
different types of CCID, addressing the following problems:

 1) The queue-drain mechanism only works with rate-based CCIDs. If CCID-2 for
    example has a full TX queue and becomes network-limited just as the
    application wants to close, then waiting for CCID-2 to become unblocked
    could lead to an indefinite  delay (i.e., application "hangs").
 2) Since each TX CCID in turn uses a feedback mechanism, there may be changes
    in its sending policy while the queue is being drained. This can lead to
    further delays during which the application will not be able to terminate.
 3) The minimum wait time for CCID-3/4 can be expected to be the queue length
    times the current inter-packet delay. For example if tx_qlen=100 and a delay
    of 15 ms is used for each packet, then the application would have to wait
    for a minimum of 1.5 seconds before being allowed to exit.
 4) There is no way for the user/application to control this behaviour. It would
    be good to use the timeout argument of dccp_close() as an upper bound. Then
    the maximum time that an application is willing to wait for its CCIDs to can
    be set via the SO_LINGER option.

These problems are addressed by giving the CCID a grace period of up to the
`timeout' value.

The wait-for-ccid function is, as before, used when the application
 (a) has read all the data in its receive buffer and
 (b) if SO_LINGER was set with a non-zero linger time, or
 (c) the socket is either in the OPEN (active close) or in the PASSIVE_CLOSEREQ
     state (client application closes after receiving CloseReq).

In addition, there is a catch-all case of __skb_queue_purge() after waiting for
the CCID. This is necessary since the write queue may still have data when
 (a) the host has been passively-closed,
 (b) abnormal termination (unread data, zero linger time),
 (c) wait-for-ccid could not finish within the given time limit.
Signed-off-by: NGerrit Renker <gerrit@erg.abdn.ac.uk>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This schedules an Ack when receiving a timestamp, exploiting the
existing inet_csk_schedule_ack() function, saving one case in the
`dccp_ack_pending()' function.
Signed-off-by: NGerrit Renker <gerrit@erg.abdn.ac.uk>

This patch generalises the task of determining data loss from RFC 4340, 7.7.1.

Let S_A, S_B be sequence numbers such that S_B is "after" S_A, and let
N_B be the NDP count of packet S_B. Then, using modulo-2^48 arithmetic,
 D = S_B - S_A - 1  is an upper bound of the number of lost data packets,
 D - N_B            is an approximation of the number of lost data packets
                    (there are cases where this is not exact).

The patch implements this as
 dccp_loss_count(S_A, S_B, N_B) := max(S_B - S_A - 1 - N_B, 0)
Signed-off-by: NIvo Calado <ivocalado@embedded.ufcg.edu.br>
Signed-off-by: NErivaldo Xavier <desadoc@gmail.com>
Signed-off-by: NLeandro Sales <leandroal@gmail.com>
Signed-off-by: NGerrit Renker <gerrit@erg.abdn.ac.uk>

This fixes a problem and a potential loophole with regard to seqno/ackno
validity: currently the initial adjustments to AWL/SWL are only performed
once at the begin of the connection, during the handshake.

Since the Sequence Window feature is always greater than Wmin=32 (7.5.2),
it is however necessary to perform these adjustments at least for the first
W/W' (variables as per 7.5.1) packets in the lifetime of a connection.

This requirement is complicated by the fact that W/W' can change at any time
during the lifetime of a connection.

Therefore it is better to perform that safety check each time SWL/AWL are
updated, as implemented by the patch.

A second problem solved by this patch is that the remote/local Sequence Window
feature values (which set the bounds for AWL/SWL/SWH) are undefined until the
feature negotiation has completed.

During the initial handshake we have more stringent sequence number protection;
the changes added by this patch effect that {A,S}W{L,H} are within the correct
bounds at the instant that feature negotiation completes (since the SeqWin
feature activation handlers call dccp_update_gsr/gss()).
Signed-off-by: NGerrit Renker <gerrit@erg.abdn.ac.uk>

Remove dead code and make some functions static.
Compile tested only.
Signed-off-by: NStephen Hemminger <shemminger@vyatta.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This removes an unused 'sk' argument from several option-inserting functions.
Signed-off-by: NGerrit Renker <gerrit@erg.abdn.ac.uk>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

inet: Remove unused send_check length argument

This patch removes the unused length argument from the send_check
function in struct inet_connection_sock_af_ops.
Signed-off-by: NHerbert Xu <herbert@gondor.apana.org.au>
Tested-by: NYinghai <yinghai.lu@oracle.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

There is no point to align or pad mibs to cache lines, they are per cpu
allocated with a 8 bytes alignment anyway.
This wastes space for no gain. This patch removes __SNMP_MIB_ALIGN__

Since SNMP mibs contain "unsigned long" fields only, we can relax the
allocation alignment from "unsigned long long" to "unsigned long"
Signed-off-by: NEric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This provides safety against negative optlen at the type
level instead of depending upon (sometimes non-trivial)
checks against this sprinkled all over the the place, in
each and every implementation.

Based upon work done by Arjan van de Ven and feedback
from Linus Torvalds.
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This fixes a problem caused by the overlap of the connection-setup and
established-state phases of DCCP connections.

During connection setup, the client retransmits Confirm Feature-Negotiation
options until a response from the server signals that it can move from the
half-established PARTOPEN into the OPEN state, whereupon the connection is
fully established on both ends (RFC 4340, 8.1.5).

However, since the client may already send data while it is in the PARTOPEN
state, consequences arise for the Maximum Packet Size: the problem is that the
initial option overhead is much higher than for the subsequent established
phase, as it involves potentially many variable-length list-type options
(server-priority options, RFC 4340, 6.4).

Applying the standard MPS is insufficient here: especially with larger
payloads this can lead to annoying, counter-intuitive EMSGSIZE errors.

On the other hand, reducing the MPS available for the established phase by
the added initial overhead is highly wasteful and inefficient.

The solution chosen therefore is a two-phase strategy:

   If the payload length of the DataAck in PARTOPEN is too large, an Ack is sent
   to carry the options, and the feature-negotiation list is then flushed.

   This means that the server gets two Acks for one Response. If both Acks get
   lost, it is probably better to restart the connection anyway and devising yet
   another special-case does not seem worth the extra complexity.

The result is a higher utilisation of the available packet space for the data
transmission phase (established state) of a connection.

The patch (over-)estimates the initial overhead to be 32*4 bytes -- commonly
seen values were around 90 bytes for initial feature-negotiation options.

It uses sizeof(u32) to mean "aligned units of 4 bytes".
For consistency, another use of 4-byte alignment is adapted.
Signed-off-by: NGerrit Renker <gerrit@erg.abdn.ac.uk>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Since all feature-negotiation processing now takes place in feat.c,
functions for producing verbose debugging output are concentrated
there.

New functions to print out values, entry records, and options are
provided, and also a macro is defined to not always have the function
name in the output line.

Thanks a lot to Wei Yongjun and Giuseppe Galeota for help and
discussion with an earlier revision of this patch.
Signed-off-by: NGerrit Renker <gerrit@erg.abdn.ac.uk>
Acked-by: NIan McDonald <ian.mcdonald@jandi.co.nz>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch takes care of initialising and type-checking sysctls
related to feature negotiation. Type checking is important since some
of the sysctls now directly impact the feature-negotiation process.

The sysctls are initialised with the known default values for each
feature.  For the type-checking the value constraints from RFC 4340
are used:

 * Sequence Window uses the specified Wmin=32, the maximum is ulong (4 bytes),
   tested and confirmed that it works up to 4294967295 - for Gbps speed;
 * Ack Ratio is between 0 .. 0xffff (2-byte unsigned integer);
 * CCIDs are between 0 .. 255;
 * request_retries, retries1, retries2 also between 0..255 for good measure;
 * tx_qlen is checked to be non-negative;
 * sync_ratelimit remains as before.

Notes:
------
 1. Die s@sysctl_dccp_feat@sysctl_dccp@g since the sysctls are now in feat.c.
 2. As pointed out by Arnaldo, the pattern of type-checking repeats itself in
    other places, sometimes with exactly the same kind of definitions (e.g.
    "static int zero;"). It may be a good idea (kernel janitors?) to consolidate
    type checking. For the sake of keeping the changeset small and in order not
    to affect other subsystems, I have not strived to generalise here.
Signed-off-by: NGerrit Renker <gerrit@erg.abdn.ac.uk>
Acked-by: NIan McDonald <ian.mcdonald@jandi.co.nz>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This adds full support for local/remote Sequence Window feature, from which the
  * sequence-number-validity (W) and
  * acknowledgment-number-validity (W') windows
derive as specified in RFC 4340, 7.5.3.

Specifically, the following is contained in this patch:
  * integrated new socket fields into dccp_sk;
  * updated the update_gsr/gss routines with regard to these fields;
  * updated handler code: the Sequence Window feature is located at the TX side,
    so the local feature is meant if the handler-rx flag is false;
  * the initialisation of `rcv_wnd' in reqsk is removed, since
    - rcv_wnd is not used by the code anywhere;
    - sequence number checks are not done in the LISTEN state (cf. 7.5.3);
    - dccp_check_req checks the Ack number validity more rigorously;
  * the `struct dccp_minisock' became empty and is now removed.
Signed-off-by: NGerrit Renker <gerrit@erg.abdn.ac.uk>
Acked-by: NIan McDonald <ian.mcdonald@jandi.co.nz>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Based on Arnaldo's earlier patch, this patch integrates the standardised
CCID congestion control plugins (CCID-2 and CCID-3) of DCCP with dccp.ko:

 * enables a faster connection path by eliminating the need to always go 
   through the CCID registration lock;

 * updates the implementation to use only a single array whose size equals
   the number of configured CCIDs instead of the maximum (256);

 * since the CCIDs are now fixed array elements, synchronization is no
   longer needed, simplifying use and implementation.

CCID-2 is suggested as minimum for a basic DCCP implementation (RFC 4340, 10);
CCID-3 is a standards-track CCID supported by RFC 4342 and RFC 5348.
Signed-off-by: NGerrit Renker <gerrit@erg.abdn.ac.uk>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This removes the use of the sysctl and the minisock variable for the Send Ack
Vector feature, as it now is handled fully dynamically via feature negotiation
(i.e. when CCID-2 is enabled, Ack Vectors are automatically enabled as per
 RFC 4341, 4.).

Using a sysctl in parallel to this implementation would open the door to
crashes, since much of the code relies on tests of the boolean minisock /
sysctl variable. Thus, this patch replaces all tests of type

	if (dccp_msk(sk)->dccpms_send_ack_vector)
		/* ... */
with
	if (dp->dccps_hc_rx_ackvec != NULL)
		/* ... */

The dccps_hc_rx_ackvec is allocated by the dccp_hdlr_ackvec() when feature
negotiation concluded that Ack Vectors are to be used on the half-connection.
Otherwise, it is NULL (due to dccp_init_sock/dccp_create_openreq_child),
so that the test is a valid one.

The activation handler for Ack Vectors is called as soon as the feature
negotiation has concluded at the
 * server when the Ack marking the transition RESPOND => OPEN arrives;
 * client after it has sent its ACK, marking the transition REQUEST => PARTOPEN.

Adding the sequence number of the Response packet to the Ack Vector has been
removed, since
 (a) connection establishment implies that the Response has been received;
 (b) the CCIDs only look at packets received in the (PART)OPEN state, i.e.
     this entry will always be ignored;
 (c) it can not be used for anything useful - to detect loss for instance, only
     packets received after the loss can serve as pseudo-dupacks.

There was a FIXME to change the error code when dccp_ackvec_add() fails.
I removed this after finding out that:
 * the check whether ackno < ISN is already made earlier,
 * this Response is likely the 1st packet with an Ackno that the client gets,
 * so when dccp_ackvec_add() fails, the reason is likely not a packet error.
Signed-off-by: NGerrit Renker <gerrit@erg.abdn.ac.uk>
Acked-by: NIan McDonald <ian.mcdonald@jandi.co.nz>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Updating the NDP count feature is handled automatically now:
 * for CCID-2 it is disabled, since the code does not use NDP counts;
 * for CCID-3 it is enabled, as NDP counts are used to determine loss lengths.

Allowing the user to change NDP values leads to unpredictable and failing
behaviour, since it is then possible to disable NDP counts even when they
are needed (e.g. in CCID-3).

This means that only those user settings are sensible that agree with the
values for Send NDP Count implied by the choice of CCID. But those settings
are already activated by the feature negotiation (CCID dependency tracking),
hence this form of support is redundant.

At startup the initialisation of the NDP count feature uses the default
value of 0, which is done implicitly by the zeroing-out of the socket when
it is allocated. If the choice of CCID or feature negotiation enables NDP
count, this will then be updated via the NDP activation handler.
Signed-off-by: NGerrit Renker <gerrit@erg.abdn.ac.uk>
Acked-by: NIan McDonald <ian.mcdonald@jandi.co.nz>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch provides the post-processing of feature negotiation state, after
the negotiation has completed.

To this purpose, handlers are used and added to the dccp_feat_table. Each
handler is passed a boolean flag whether the RX or TX side of the feature
is meant.

Several handlers are provided already, new handlers can easily be added.

The initialisation is now fully dynamic, i.e. CCIDs are activated only
after the feature negotiation. The integration of this dynamic activation
is done in the subsequent patches.

Thanks to Wei Yongjun for pointing out the necessity of skipping over empty
Confirm options while copying the negotiated feature values.
Signed-off-by: NGerrit Renker <gerrit@erg.abdn.ac.uk>
Acked-by: NIan McDonald <ian.mcdonald@jandi.co.nz>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch replaces the earlier insertion routine from options.c, so that
code specific to feature negotiation can remain in feat.c. This is possible
by calling a function already existing in options.c.
Signed-off-by: NGerrit Renker <gerrit@erg.abdn.ac.uk>
Acked-by: NIan McDonald <ian.mcdonald@jandi.co.nz>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Instead of using one atomic_t per protocol, use a percpu_counter
for "orphan_count", to reduce cache line contention on
heavy duty network servers. 
Signed-off-by: NEric Dumazet <dada1@cosmosbay.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch deprecates the Ack Ratio sysctl, since
 * Ack Ratio is entirely ignored by CCID-3 and CCID-4,
 * Ack Ratio currently doesn't work in CCID-2 (i.e. is always set to 1);
 * even if it would work in CCID-2, there is no point for a user to change it:
   - Ack Ratio is constrained by cwnd (RFC 4341, 6.1.2),
   - if Ack Ratio > cwnd, the system resorts to spurious RTO timeouts
     (since waiting for Acks which will never arrive in this window),
   - cwnd is not a user-configurable value.

The only reasonable place for Ack Ratio is to print it for debugging. It is
planned to do this later on, as part of e.g. dccp_probe.

With this patch Ack Ratio is now under full control of feature negotiation:
 * Ack Ratio is resolved as a dependency of the selected CCID;
 * if the chosen CCID supports it (i.e. CCID == CCID-2), Ack Ratio is set to
   the default of 2, following RFC 4340, 11.3 - "New connections start with Ack
   Ratio 2 for both endpoints";
 * what happens then is part of another patch set, since it concerns the
   dynamic update of Ack Ratio while the connection is in full flight.

Thanks to Tomasz Grobelny for discussion leading up to this patch.
Signed-off-by: NGerrit Renker <gerrit@erg.abdn.ac.uk>
Acked-by: NArnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This adds a hook to resolve features whose value depends on the choice of
CCID. It is done at the server since it can only be done after the CCID
values have been negotiated; i.e. the client will add its CCID preference
list on the Change options sent in the Request, which will be reconciled
with the local preference list of the server.

The concept is documented on
http://www.erg.abdn.ac.uk/users/gerrit/dccp/notes/feature_negotiation/\
				implementation_notes.html#ccid_dependencies
Signed-off-by: NGerrit Renker <gerrit@erg.abdn.ac.uk>
Acked-by: NIan McDonald <ian.mcdonald@jandi.co.nz>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This provides a missing link in the code chain, as several features implicitly
depend and/or rely on the choice of CCID. Most notably, this is the Send Ack Vector
feature, but also Ack Ratio and Send Loss Event Rate (also taken care of).

For Send Ack Vector, the situation is as follows:
 * since CCID2 mandates the use of Ack Vectors, there is no point in allowing 
   endpoints which use CCID2 to disable Ack Vector features such a connection;

 * a peer with a TX CCID of CCID2 will always expect Ack Vectors, and a peer
   with a RX CCID of CCID2 must always send Ack Vectors (RFC 4341, sec. 4);

 * for all other CCIDs, the use of (Send) Ack Vector is optional and thus
   negotiable. However, this implies that the code negotiating the use of Ack
   Vectors also supports it (i.e. is able to supply and to either parse or
   ignore received Ack Vectors). Since this is not the case (CCID-3 has no Ack
   Vector support), the use of Ack Vectors is here disabled, with a comment
   in the source code.

An analogous consideration arises for the Send Loss Event Rate feature,
since the CCID-3 implementation does not support the loss interval options
of RFC 4342. To make such use explicit, corresponding feature-negotiation
options are inserted which signal the use of the loss event rate option,
as it is used by the CCID3 code.

Lastly, the values of the Ack Ratio feature are matched to the choice of CCID.

The patch implements this as a function which is called after the user has
made all other registrations for changing default values of features.

The table is variable-length, the reserved (and hence for feature-negotiation
invalid, confirmed by considering section 19.4 of RFC 4340) feature number `0'
is used to mark the end of the table.
Signed-off-by: NGerrit Renker <gerrit@erg.abdn.ac.uk>
Acked-by: NIan McDonald <ian.mcdonald@jandi.co.nz>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This provides feature-negotiation initialisation for both DCCP sockets
and DCCP request_sockets, to support feature negotiation during
connection setup.

It also resolves a FIXME regarding the congestion control
initialisation.

Thanks to Wei Yongjun for help with the IPv6 side of this patch.
Signed-off-by: NGerrit Renker <gerrit@erg.abdn.ac.uk>
Acked-by: NIan McDonald <ian.mcdonald@jandi.co.nz>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This adds list initial fields and list management functions for the
new feature negotiation implementation.

Thanks to Arnaldo for suggestions and improvements.
Signed-off-by: NGerrit Renker <gerrit@erg.abdn.ac.uk>
Acked-by: NIan McDonald <ian.mcdonald@jandi.co.nz>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

as it accentally contained the wrong set of patches. These will be
submitted separately.
Signed-off-by: NGerrit Renker <gerrit@erg.abdn.ac.uk>

This extracts the clamping part of dccp_sample_rtt() and makes it available
to other parts of the code (as e.g. used in the next patch).

Note: The function dccp_sample_rtt() now reduces to subtracting the elapsed
time. This could be eliminated but would require shorter prefixes and thus
is not done by this patch - maybe an idea for later.
Signed-off-by: NGerrit Renker <gerrit@erg.abdn.ac.uk>

The DCCP base time resolution is 10 microseconds (RFC 4340, 13.1 ... 13.3).

Using a timer with a lower resolution was found to trigger the following
bug warnings/problems on high-speed networks (e.g. local loopback):
 * RTT samples are rounded down to 0 if below resolution;
 * in some cases, negative RTT samples were observed;
 * the CCID-3 feedback timer complains that the feedback interval is 0,
   since the feedback interval is in the order of 1 RTT or less and RTT
   measurement rounded this down to 0;
On an Intel computer this will for instance happen when using a
boot-time parameter of "clocksource=jiffies".

The following system log messages were observed:
  11:24:00 kernel: BUG: delta (0) <= 0 at ccid3_hc_rx_send_feedback()
  11:26:12 kernel: BUG: delta (0) <= 0 at ccid3_hc_rx_send_feedback()
  11:26:30 kernel: dccp_sample_rtt: unusable RTT sample 0, using min
  11:26:30 last message repeated 5 times

This patch defines a global constant for the time resolution, adds this in
timer.c, and checks the available clock resolution at CCID-3 module load time.

When the resolution is worse than 10 microseconds, module loading exits with
a message "socket type not supported".
Signed-off-by: NGerrit Renker <gerrit@erg.abdn.ac.uk>

Ensure that cmsg->cmsg_type value is valid for qpolicy 
that is currently in use.
Signed-off-by: NTomasz Grobelny <tomasz@grobelny.oswiecenia.net>
Signed-off-by: NGerrit Renker <gerrit@erg.abdn.ac.uk>

This patch adds a generic infrastructure for policy-based dequeueing of 
TX packets and provides two policies:
 * a simple FIFO policy (which is the default) and
 * a priority based policy (set via socket options).
Both policies honour the tx_qlen sysctl for the maximum size of the write
queue (can be overridden via socket options). 

The priority policy uses skb->priority internally to assign an u32 priority
identifier, using the same ranking as SO_PRIORITY. The skb->priority field
is set to 0 when the packet leaves DCCP. The priority is supplied as ancillary
data using cmsg(3), the patch also provides the requisite parsing routines.
Signed-off-by: NTomasz Grobelny <tomasz@grobelny.oswiecenia.net>
Signed-off-by: NGerrit Renker <gerrit@erg.abdn.ac.uk>

This extends the existing wait-for-ccid routine so that it may be used with
different types of CCID. It further addresses the problems listed below.

The code looks if the write queue is non-empty and grants the TX CCID up to
`timeout' jiffies to drain the queue. It will instead purge that queue if
 * the delay suggested by the CCID exceeds the time budget;
 * a socket error occurred while waiting for the CCID;
 * there is a signal pending (eg. annoyed user pressed Control-C);
 * the CCID does not support delays (we don't know how long it will take).


                 D e t a i l s  [can be removed]
                 -------------------------------
DCCP's sending mechanism functions a bit like non-blocking I/O: dccp_sendmsg()
will enqueue up to net.dccp.default.tx_qlen packets (default=5), without waiting
for them to be released to the network.

Rate-based CCIDs, such as CCID3/4, can impose sending delays of up to maximally
64 seconds (t_mbi in RFC 3448). Hence the write queue may still contain packets
when the application closes. Since the write queue is congestion-controlled by
the CCID, draining the queue is also under control of the CCID.

There are several problems that needed to be addressed:
 1) The queue-drain mechanism only works with rate-based CCIDs. If CCID2 for
    example has a full TX queue and becomes network-limited just as the
    application wants to close, then waiting for CCID2 to become unblocked could
    lead to an indefinite  delay (i.e., application "hangs").
 2) Since each TX CCID in turn uses a feedback mechanism, there may be changes
    in its sending policy while the queue is being drained. This can lead to
    further delays during which the application will not be able to terminate.
 3) The minimum wait time for CCID3/4 can be expected to be the queue length
    times the current inter-packet delay. For example if tx_qlen=100 and a delay
    of 15 ms is used for each packet, then the application would have to wait
    for a minimum of 1.5 seconds before being allowed to exit.
 4) There is no way for the user/application to control this behaviour. It would
    be good to use the timeout argument of dccp_close() as an upper bound. Then
    the maximum time that an application is willing to wait for its CCIDs to can
    be set via the SO_LINGER option.

These problems are addressed by giving the CCID a grace period of up to the
`timeout' value.

The wait-for-ccid function is, as before, used when the application 
 (a) has read all the data in its receive buffer and
 (b) if SO_LINGER was set with a non-zero linger time, or
 (c) the socket is either in the OPEN (active close) or in the PASSIVE_CLOSEREQ
     state (client application closes after receiving CloseReq).

In addition, there is a catch-all case by calling __skb_queue_purge() after 
waiting for the CCID. This is necessary since the write queue may still have
data when
 (a) the host has been passively-closed,
 (b) abnormal termination (unread data, zero linger time),
 (c) wait-for-ccid could not finish within the given time limit.
Signed-off-by: NGerrit Renker <gerrit@erg.abdn.ac.uk>

This completes the implementation of a circular buffer for Ack Vectors, by 
extending the current (linear array-based) implementation.  The changes are:

 (a) An `overflow' flag to deal with the case of overflow. As before, dynamic
     growth of the buffer will not be supported; but code will be added to deal
     robustly with overflowing Ack Vector buffers.

 (b) A `tail_seqno' field. When naively implementing the algorithm of Appendix A
     in RFC 4340, problems arise whenever subsequent Ack Vector records overlap,
     which can bring the entire run length calculation completely out of synch.
     (This is documented on http://www.erg.abdn.ac.uk/users/gerrit/dccp/notes/\
                                             ack_vectors/tracking_tail_ackno/ .)
 (c) The buffer lengthi is now computed dynamically (i.e. current fill level),
     as the span between head to tail.

As a result, dccp_ackvec_pending() is now simpler - the #ifdef is no longer 
necessary since buf_empty is always true when IP_DCCP_ACKVEC is not configured.

Note on overflow handling: 
-------------------------
 The Ack Vector code previously simply started to drop packets when the
 Ack Vector buffer overflowed. This means that the userspace application
 will not be able to receive, only because of an Ack Vector storage problem.
 
 Furthermore, overflow may be transient, so that applications may later
 recover from the overflow. Recovering from dropped packets is more difficult
 (e.g. video key frames).
 
 Hence the patch uses a different policy: when the buffer overflows, the oldest
 entries are subsequently overwritten. This has a higher chance of recovery.
 Details are on http://www.erg.abdn.ac.uk/users/gerrit/dccp/notes/ack_vectors/Signed-off-by: NGerrit Renker <gerrit@erg.abdn.ac.uk>

This fixes a problem and a potential loophole with regard to seqno/ackno
validity: the problem is that the initial adjustments to AWL/SWL were
only performed at the begin of the connection, during the handshake.

Since the Sequence Window feature is always greater than Wmin=32 (7.5.2), 
it is however necessary to perform these adjustments at least for the first
W/W' (variables as per 7.5.1) packets in the lifetime of a connection.

This requirement is complicated by the fact that W/W' can change at any time
during the lifetime of a connection.

Therefore the consequence is to perform this safety check each time SWL/AWL
are updated.

A second problem solved by this patch is that the remote/local Sequence Window
feature values (which set the bounds for AWL/SWL/SWH) are undefined until the
feature negotiation has completed.

During the initial handshake we have more stringent sequence number protection,
the changes added by this patch effect that {A,S}W{L,H} are within the correct
bounds at the instant that feature negotiation completes (since the SeqWin
feature activation handlers call dccp_update_gsr/gss()). 

A detailed rationale is below -- can be removed from the commit message.


1. Server sequence number checks during initial handshake
---------------------------------------------------------
The server can not use the fields of the listening socket for seqno/ackno checks
and thus needs to store all relevant information on a per-connection basis on
the dccp_request socket. This is a size-constrained structure and has currently
only ISS (dreq_iss) and ISR (dreq_isr) defined.
Adding further fields (SW{L,H}, AW{L,H}) would increase the size of the struct
and it is questionable whether this will have any practical gain. The currently
implemented solution is as follows.
 * receiving first Request: dccp_v{4,6}_conn_request sets 
                            ISR := P.seqno, ISS := dccp_v{4,6}_init_sequence()

 * sending first Response:  dccp_v{4,6}_send_response via dccp_make_response()	
                            sets P.seqno := ISS, sets P.ackno := ISR

 * receiving retransmitted Request: dccp_check_req() overrides ISR := P.seqno

 * answering retransmitted Request: dccp_make_response() sets ISS += 1,
                                    otherwise as per first Response

 * completing the handshake: succeeds in dccp_check_req() for the first Ack
                             where P.ackno == ISS (P.seqno is not tested)

 * creating child socket: ISS, ISR are copied from the request_sock

This solution will succeed whenever the server can receive the Request and the
subsequent Ack in succession, without retransmissions. If there is packet loss,
the client needs to retransmit until this condition succeeds; it will otherwise
eventually give up. Adding further fields to the request_sock could increase
the robustness a bit, in that it would make possible to let a reordered Ack
(from a retransmitted Response) pass. The argument against such a solution is
that if the packet loss is not persistent and an Ack gets through, why not
wait for the one answering the original response: if the loss is persistent, it
is probably better to not start the connection in the first place.

Long story short: the present design (by Arnaldo) is simple and will likely work
just as well as a more complicated solution. As a consequence, {A,S}W{L,H} are
not needed until the moment the request_sock is cloned into the accept queue.

At that stage feature negotiation has completed, so that the values for the local
and remote Sequence Window feature (7.5.2) are known, i.e. we are now in a better
position to compute {A,S}W{L,H}.


2. Client sequence number checks during initial handshake
---------------------------------------------------------
Until entering PARTOPEN the client does not need the adjustments, since it 
constrains the Ack window to the packet it sent.

 * sending first Request: dccp_v{4,6}_connect() choose ISS, 
                          dccp_connect() then sets GAR := ISS (as per 8.5),
			  dccp_transmit_skb() (with the previous bug fix) sets
			         GSS := ISS, AWL := ISS, AWH := GSS
 * n-th retransmitted Request (with previous patch):
	                  dccp_retransmit_skb() via timer calls
			  dccp_transmit_skb(), which sets GSS := ISS+n
                          and then AWL := ISS, AWH := ISS+n
	                  
 * receiving any Response: dccp_rcv_request_sent_state_process() 
	                   -- accepts packet if AWL <= P.ackno <= AWH;
			   -- sets GSR = ISR = P.seqno

 * sending the Ack completing the handshake: dccp_send_ack() calls 
                           dccp_transmit_skb(), which sets GSS += 1
			   and AWL := ISS, AWH := GSS
Signed-off-by: NGerrit Renker <gerrit@erg.abdn.ac.uk>

This schedules an Ack when receiving a timestamp, exploiting the
existing inet_csk_schedule_ack() function, saving one case in the
`dccp_ack_pending()' function.
Signed-off-by: NGerrit Renker <gerrit@erg.abdn.ac.uk>

To increase robustness, it is necessary to resend Confirm feature-negotiation
options, even though the RFC does not mandate it. But feature negotiation
options can take (much) more room than the options on common DataAck packets.

Instead of reducing the MPS always for a case which only applies to the three
messages send during initial handshake, this patch devises a special case:

   if the payload length of the DataAck in PARTOPEN is too large, an Ack is sent
   to carry the options, and the feature-negotiation list is then flushed.

   This means that the server gets two Acks for one Response. If both Acks get
   lost, it is probably better to restart the connection anyway and devising yet
   another special-case does not seem worth the extra complexity.

The patch (over-)estimates the expected overhead to be 32*4 bytes -- commonly
seen values were 20-90 bytes for initial feature-negotiation options. 

It uses sizeof(u32) to mean "aligned units of 4 bytes". For consistency,
another use of sizeof is modified.
Signed-off-by: NGerrit Renker <gerrit@erg.abdn.ac.uk>

In contrast to static feature negotiation at the begin of a connection, which
establishes the capabilities of both endpoints, this patch introduces support
for dynamic exchange of feature negotiation options.

Such a dynamic exchange is necessary in at least two cases:
 * CCID-2's Ack Ratio (RFC 4341, 6.1.2) which changes during the connection;
 * Sequence Window values that, as per RFC 4340, 7.5.2, should be sent "as
   as the connection progresses".

Both are NN (non-negotiable) features. Hence dynamic feature "negotiation" is
distinguished from static/pre-connection negotiation by the following:
 * no new capabilities are negotiated (those that matter for the connection
   are negotiated prior to setting up the connection, comparable to SIP);
 * features must be understood by each endpoint: as per RFC 4340, 6.4, 
   Sequence Window is "Req'd" and Ack Ratio must be understood when CCID-2
   is used as per the note underneath Table 4.

These characteristics are reflected in the implementation:
 * only NN options can be exchanged after connection setup;
 * NN options are activated directly after validating them. The rationale is
   that a peer must accept every valid NN value (RFC 4340, 6.3.2), hence it
   will either accept the value and send a "Confirm R", or it will send an
   empty Confirm (which will reset the connection according to FN rules). 
 * An Ack is scheduled directly after activation to accelerate communicating
   the update to the peer.
Signed-off-by: NGerrit Renker <gerrit@erg.abdn.ac.uk>
Acked-by: NIan McDonald <ian.mcdonald@jandi.co.nz>

Since all feature-negotiation processing now takes place in feat.c, functions
for producing verbose debugging output are concentrated there.

New functions to print out values, entry records, and options are provided,
and also a macro is defined to not always have the function name in the
output line.

Thanks a lot to Wei Yongjun and Giuseppe Galeota for help with errors in an
earlier revision of this patch.
Signed-off-by: NGerrit Renker <gerrit@erg.abdn.ac.uk>
Acked-by: NIan McDonald <ian.mcdonald@jandi.co.nz>

This patch takes care of initialising and type-checking sysctls related to
feature negotiation. Type checking is important since some of the sysctls
now directly act on the feature-negotiation process.

The sysctls are initialised with the known default values for each feature.
For the type-checking the value constraints from RFC 4340 are used:

 * Sequence Window uses the specified Wmin=32, the maximum is ulong (4 bytes),
   tested and confirmed that it works up to 4294967295 - for Gbps speed;
 * Ack Ratio is between 0 .. 0xffff (2-byte unsigned integer);
 * CCIDs are between 0 .. 255;
 * request_retries, retries1, retries2 also between 0..255 for good measure;
 * tx_qlen is checked to be non-negative;
 * sync_ratelimit remains as before.

Further changes:
----------------
Performed s@sysctl_dccp_feat@sysctl_dccp@g since the sysctls are now in feat.c.
Signed-off-by: NGerrit Renker <gerrit@erg.abdn.ac.uk>
Acked-by: NIan McDonald <ian.mcdonald@jandi.co.nz>

This adds full support for local/remote Sequence Window feature, from which the 
  * sequence-number-validity (W) and 
  * acknowledgment-number-validity (W') windows 
derive as specified in RFC 4340, 7.5.3. 

Specifically, the following changes are introduced:
  * integrated new socket fields into dccp_sk;
  * updated the update_gsr/gss routines with regard to these fields;
  * updated handler code: the Sequence Window feature is located at the TX side,
    so the local feature is meant if the handler-rx flag is false;
  * the initialisation of `rcv_wnd' in reqsk is removed, since
    - rcv_wnd is not used by the code anywhere;
    - sequence number checks are not done in the LISTEN state (cf. 7.5.3);
    - dccp_check_req checks the Ack number validity more rigorously;
  * the `struct dccp_minisock' became empty and is now removed.

Until the handshake completes with activating negotiated values, the local/remote
Sequence-Window values are undefined and thus can not reliably be estimated.
This issue is addressed in a separate patch.
Signed-off-by: NGerrit Renker <gerrit@erg.abdn.ac.uk>
Acked-by: NIan McDonald <ian.mcdonald@jandi.co.nz>