Most of the sw resets in the code are done by one function,
which writes to the relevant CSR.

Use the common function to perform the only reset which was
done separately, redundant to the common code.
Signed-off-by: NGolan Ben Ami <golan.ben.ami@intel.com>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

Support internal debug data collection on 9000 and newer
devices.
The method for finding the base and end address has changed
on new HW's, so introduce a new version of debug destination
tlv.
Signed-off-by: NGolan Ben Ami <golan.ben.ami@intel.com>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

Generate rules for the NFP to encapsulate packets in Geneve tunnels. Move
the vxlan action code to generic udp tunnel actions and use core code for
both vxlan and Geneve.

Only support outputting to well known port 6081. Setting tunnel options
is not supported yet.

Only attempt to offload if the fw supports Geneve.
Signed-off-by: NJohn Hurley <john.hurley@netronome.com>
Reviewed-by: NJakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: NSimon Horman <simon.horman@netronome.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Compile Geneve match fields for offloading to the NFP. The addition of
Geneve overflows the 8 bit key_layer field, so apply extended metadata to
the match cmsg allowing up to 32 more key_layer fields.

Rather than adding new Geneve blocks, move the vxlan code to generic ipv4
udp tunnel structs and use these for both vxlan and Geneve.

Matches are only supported when specifically mentioning well known port
6081. Geneve tunnel options are not yet included in the match.

Only offload Geneve if the fw supports it - include check for this.
Signed-off-by: NJohn Hurley <john.hurley@netronome.com>
Reviewed-by: NJakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: NSimon Horman <simon.horman@netronome.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Extract the _abi_flower_extra_features symbol from the fw which gives a 64
bit bitmap of new features (on top of the flower base support) that the fw
can offload. Store this bitmap in the priv data associated with each app.
If the symbol does not exist, set the bitmap to 0.
Signed-off-by: NJohn Hurley <john.hurley@netronome.com>
Reviewed-by: NJakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: NSimon Horman <simon.horman@netronome.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The tunnel dest IP is required for separate offload to the NFP. It is
already verified that a dest IP must be present and must be an exact
match in the flower rule. Therefore, we can just extract the IP from the
generated offload rule and remove the unused mask variable. The function
is then no longer required to return the IP separately.

Because tun_dst is localised to tunnel matches, move the declaration to
the tunnel if branch.
Signed-off-by: NJohn Hurley <john.hurley@netronome.com>
Reviewed-by: NJakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: NSimon Horman <simon.horman@netronome.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

RSS table is 4k for T6 and later cards, add check for the
same.
Signed-off-by: NGanesh Goudar <ganeshgr@chelsio.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

In recent tests with new adapters, it was discovered that ARP
packets were not being properly processed. This patch adds
support for ARP packet headers to be passed to backing adapters,
if necessary.
Signed-off-by: NThomas Falcon <tlfalcon@linux.vnet.ibm.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Increase the number of queues allocated to accommodate recent
network adapter inclusions on the IBM vNIC platform.
Signed-off-by: NThomas Falcon <tlfalcon@linux.vnet.ibm.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This value denotes the maximum number of TX queues but is used
to allocate both RX and TX queues.
Signed-off-by: NThomas Falcon <tlfalcon@linux.vnet.ibm.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

For T6, tid start range should be read from
LE_DB_ACTIVE_TABLE_START_INDEX_A register.
Signed-off-by: NArjun Vynipadath <arjun@chelsio.com>
Signed-off-by: NGanesh Goudar <ganeshgr@chelsio.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Allow the boot loader to specify the MAC address in the device tree
to override the EEPROM, or in case no EEPROM is present.

Cc: Ben Dooks <ben@simtec.co.uk>
Cc: Tristram Ha <tristram.ha@micrel.com>
Cc: David J. Choi <david.choi@micrel.com>
Signed-off-by: NLukas Wunner <lukas@wunner.de>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Directly use the platform device for generating the miibus name. This
removes the last user of bcm_enet_priv::mac_id and we can remove the
field.
Signed-off-by: NJonas Gorski <jonas.gorski@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Enabling the ephy clock for mac 1 is harmless, and the actual usage of
the ephy is not restricted to mac 0, so we might as well remove the
check.
Signed-off-by: NJonas Gorski <jonas.gorski@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

To reduce the reliance on device ids, pass the dma channel numbers to
the enet devices as platform data.
Signed-off-by: NJonas Gorski <jonas.gorski@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Now that we have the individual clocks available as "enet" we
don't need to rely on the device id for them anymore.
Signed-off-by: NJonas Gorski <jonas.gorski@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Since we now hold RTNL lock in geneve_exit_net, it's better batch them
to speedup geneve tunnel dismantle.
Signed-off-by: NHaishuang Yan <yanhaishuang@cmss.chinamobile.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Since we now hold RTNL lock in vxlan_exit_net, it's better to batch them
to speedup vxlan tunnels dismantle.
Signed-off-by: NHaishuang Yan <yanhaishuang@cmss.chinamobile.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Since both first_tx_ctx and tx_skb are the head of tx ctx, it not
necessary to use two structure members to statically indicate
the head of tx ctx. So first_tx_ctx is removed.

CC: Srinivas Eeda <srinivas.eeda@oracle.com>
CC: Joe Jin <joe.jin@oracle.com>
CC: Junxiao Bi <junxiao.bi@oracle.com>
Signed-off-by: NZhu Yanjun <yanjun.zhu@oracle.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Advertise NETIF_F_GRO_HW and set edev->gro_disable according to the
feature flag.  Add qede_fix_features() to drop NETIF_F_GRO_HW if
XDP is running or MTU does not support GRO_HW or GRO is not set.
qede_change_mtu() also checks and disables GRO_HW if MTU is not
supported.

Cc: Ariel Elior <Ariel.Elior@cavium.com>
Cc: everest-linux-l2@cavium.com
Acked-by: NManish Chopra <manish.chopra@cavium.com>
Signed-off-by: NMichael Chan <michael.chan@broadcom.com>
Acked-by: NManish Chopra <manish.chopra@cavium.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Advertise NETIF_F_GRO_HW and turn on TPA_MODE_GRO when NETIF_F_GRO_HW
is set.  Disable NETIF_F_GRO_HW in bnx2x_fix_features() if the MTU
does not support TPA_MODE_GRO or GRO is not set.  bnx2x_change_mtu() also
needs to disable NETIF_F_GRO_HW if the MTU does not support it.

Original parameter disable_tpa will continue to disable LRO and GRO_HW.

Preserve the original behavior of enabling LRO by default.  User has
to run ethtool -K to explicitly enable GRO_HW.

Cc: Ariel Elior <Ariel.Elior@cavium.com>
Cc: everest-linux-l2@cavium.com
Signed-off-by: NMichael Chan <michael.chan@broadcom.com>
Acked-by: NManish Chopra <manish.chopra@cavium.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Advertise NETIF_F_GRO_HW in hw_features if hardware GRO is supported.
In bnxt_fix_features(), disable GRO_HW and LRO if current hardware
configuration does not allow it.  GRO_HW depends on GRO.  GRO_HW is
also mutually exclusive with LRO.  XDP setup will now rely on
bnxt_fix_features() to turn off aggregation.  During chip init, turn on
or off hardware GRO based on NETIF_F_GRO_HW in features flag.
Signed-off-by: NMichael Chan <michael.chan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Simplify PCIe Completion Timeout setting by using the
pcie_capability_clear_and_set_word() interface.  No functional change
intended.
Signed-off-by: NBjorn Helgaas <bhelgaas@google.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Use ASSERT_RTNL() rather than WARN_ON(!lockdep_rtnl_is_held()) which
stops working when lockdep fires, and we end up with lots of warnings.

Fixes: 9525ae83 ("phylink: add phylink infrastructure")
Signed-off-by: NRussell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The EEPROM reading was trying to read from the second EEPROM address
if we requested the last byte from the SFF8079 EEPROM, which caused a
failure when the second EEPROM is not present.  Discovered with a
S-RJ01 SFP module.  Fix this.

Fixes: 73970055 ("sfp: add SFP module support")
Signed-off-by: NRussell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The detection of a PHY changed in commit e98a3aab ("mdio_bus: don't
return NULL from mdiobus_scan()") which now causes sfp to print an
error message.  Update for this change.

Fixes: 73970055 ("sfp: add SFP module support")
Signed-off-by: NRussell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Following previous changes, join the other authors of this driver and
take the blame with them
Reviewed-by: NAndrew Lunn <andrew@lunn.ch>
Signed-off-by: NJerome Brunet <jbrunet@baylibre.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Enable interrupt support in meson-gxl PHY driver
Signed-off-by: NJerome Brunet <jbrunet@baylibre.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The PHY performs just as well when left in its default configuration and
it makes senses because this poke gets reset just after init.

According to the documentation, all registers in the Analog/DSP bank are
reset when there is a mode switch from 10BT to 100BT. The bank is also
reset on power down and soft reset, so we will never see the value which
may have been set by the bootloader.

In the end, we have used the default configuration so far and there is no
reason to change now. Remove CONFIG_A6 poke to make this clear.
Reviewed-by: NAndrew Lunn <andrew@lunn.ch>
Signed-off-by: NJerome Brunet <jbrunet@baylibre.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Use the generic init function to populate some of the phydev
structure fields
Reviewed-by: NAndrew Lunn <andrew@lunn.ch>
Signed-off-by: NJerome Brunet <jbrunet@baylibre.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add read and write helpers to manipulate banked registers on this PHY
This helps clarify the settings applied to these registers and what the
driver actually does
Signed-off-by: NNeil Armstrong <narmstrong@baylibre.com>
Signed-off-by: NJerome Brunet <jbrunet@baylibre.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Define registers and bits in meson-gxl PHY driver to make a bit
more human friendly. No functional change.
Signed-off-by: NNeil Armstrong <narmstrong@baylibre.com>
Signed-off-by: NJerome Brunet <jbrunet@baylibre.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Always check phy_write return values. Better to be safe than sorry
Reviewed-by: NAndrew Lunn <andrew@lunn.ch>
Signed-off-by: NJerome Brunet <jbrunet@baylibre.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The timer mode register now has a separate field for the reload value.
Since we always use this timer with the reload (for interrupt moderation)
we set this to the same as the initial value.

Previous hardware ignores this field, so we can safely set these bits
on all hardware that uses this register.
Signed-off-by: NEdward Cree <ecree@solarflare.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The RX_L4_CLASS field has shrunk from 3 bits to 2 bits. The upper
bit was never used in previous hardware, so we can use the new
definition throughout.

The TSO OUTER_IPID field was previously spelt differently from the
external definitions.
Signed-off-by: NEdward Cree <ecree@solarflare.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Log a message if PTP probing fails; if we then, unexpectedly, get PTP
 events, only log a message for the first one on each device.
Signed-off-by: NEdward Cree <ecree@solarflare.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NEdward Cree <ecree@solarflare.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Medford2 can also have 16k or 64k VI stride.  This is reported by MCDI in
 GET_CAPABILITIES, which fortunately is called before the driver does
 anything sensitive to the VI stride (such as accessing or even allocating
 VIs past the zeroth).
Signed-off-by: NEdward Cree <ecree@solarflare.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Support using BAR 0 on SFC9250, even though the driver doesn't bind to such
 devices yet.
Signed-off-by: NEdward Cree <ecree@solarflare.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

netdev_bpf.flags is the input member for installing the program.
netdev_bpf.prog_flags is the output member for querying.  Set
the correct one on query.

Fixes: 92f0292b ("net: xdp: report flags program was installed with on query")
Signed-off-by: NJakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: NQuentin Monnet <quentin.monnet@netronome.com>
Signed-off-by: NDaniel Borkmann <daniel@iogearbox.net>