Signed-off-by: NNobuhiro Iwamatsu <iwamatsu@nigauri.org>
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

This kills off the ancient p3_ioremap(), converting over to the more
generic ioremap_prot() instead.
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

Presently 'flags' gets passed around a lot between the various ioremap
helpers and implementations, which is only 32-bits. In the X2TLB case
we use 64-bit pgprots which presently results in the upper 32bits being
chopped off (which handily include our read/write/exec permissions).

As such, we convert everything internally to using pgprot_t directly and
simply convert over with pgprot_val() where needed. With this in place,
transparent fixmap utilization for early ioremap works as expected.
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

This also fixes up a long-standing bug for this platform where the PIO
base was set to a register offset, rather than the actual PIO offset
itself.
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

This gets rid of the cf enabler use on mach-sh03 and switches to use
pata_platform with the proper address directly. cf_enabler is
subsequently disabled for mach-sh03.
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

This flattens out the board directories in to individual mach groups,
we will use this for getting rid of unneeded directories, simplifying
the build system, and becoming more coherent with the refactored
arch/sh/include topology.
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

This follows the sparc changes a439fe51.

Most of the moving about was done with Sam's directions at:

http://marc.info/?l=linux-sh&m=121724823706062&w=2

with subsequent hacking and fixups entirely my fault.
Signed-off-by: NSam Ravnborg <sam@ravnborg.org>
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

We were abusing the resource size for the number of bits, this
has been reworked using proper platform data, so this can be
tidied up now. Boards in general only have a 1-byte wide resource,
which the ioremap_nocache() case already handles.
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

This patch removes redundant board specific interrupt code for boards
using sh775x processors and 4 IRQ lines in "Individual Interrupt Mode"
aka IRLM.

Three boards are affected: sh03, snapgear and titan.

The right way to do this is to use cpu specific code provided by intc.
A nice side effect is that sh03 now compiles, board not BROKEN any more.
Signed-off-by: NMagnus Damm <damm@igel.co.jp>
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

This patch reworks the ipr code by grouping the offset array together
with the ipr_data structure in a new data structure called ipr_desc.
This new structure also contains the name of the controller in struct
irq_chip. The idea behind putting struct irq_chip in there is that we
can use offsetof() to locate the base addresses in the irq_chip
callbacks. This strategy has much in common with the recently merged
intc2 code.

One logic change has been made - the original ipr code enabled the
interrupts by default but with this patch they are all disabled by
default.
Signed-off-by: NMagnus Damm <damm@igel.co.jp>
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

We now throw all of the machvecs in to .machvec.init and either
select one on the command line, or copy out the first (and
usually only) one to sh_mv. The rest are freed as usual.

This gets rid of all of the silly sh_mv aliasing and makes the
selection explicit rather than link-order dependent.
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

This consolidates the various board heartbeat LED implementations,
used for strobing the load average across a LED bank. Those boards
not implementing a full bank can hook in via the LED class.

We leave the compat hook in the machvec for now until those non-banked
boards are able to migrate to the drivers/leds.
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

The conversion from IPR-IRQ to IRQ-chip resulted in the
ipr data being allocated in a local variable in
make_ipr_irq - breaking anything using IPR interrupts.

This changes all of the callers of make_ipr_irq to
allocate a static structure containing the IPR data which
is then passed to make_ipr_irq. This removes the need for
make_ipr_irq to allocate any additional space for the IPR
information.
Signed-off-by: NJamie Lenehan <lenehan@twibble.org>
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

Get all of the defconfigs building again.
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

Some more machvec overhauling and setup code cleanup. Kill off
get_system_type() and platform_setup(), we can do these both
through the machvec. While we're add it, kill off more useless
mach.c's and drop some legacy cruft from setup.c.
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

This cleans up quite a lot of the PCI mess that we
currently have, and attempts to consolidate the
duplication in the SH7780 and SH7751 PCI controllers.
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

This updates the various boards for some of the recent I/O routine
updates.
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

Signed-off-by: NJörn Engel <joern@wohnheim.fh-wedel.de>
Signed-off-by: NAdrian Bunk <bunk@stusta.de>

Initial git repository build. I'm not bothering with the full history,
even though we have it. We can create a separate "historical" git
archive of that later if we want to, and in the meantime it's about
3.2GB when imported into git - space that would just make the early
git days unnecessarily complicated, when we don't have a lot of good
infrastructure for it.

Let it rip!