For completeness and correctness, the VF driver needs to reserve these
RSS and L2 contexts.
Signed-off-by: NMichael Chan <michael.chan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When rings are more limited and the PF has not provisioned minimum
guaranteed rings to the VF, do not reserve rings during driver probe.
Wait till device open before reserving rings when they will be used.
Device open will succeed if some minimum rings can be successfully
reserved and allocated.
Signed-off-by: NMichael Chan <michael.chan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The current code does not reserve rings during ethtool -L when the device
is down.  The rings will be reserved when the device is later opened.

Change it to reserve rings during ethtool -L when the device is down.
This provides a better guarantee that the device open will be successful
when the rings are reserved ahead of time.
Signed-off-by: NMichael Chan <michael.chan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This adds debugfs support for bnxt_en with the purpose of allowing users
to examine the current DIM profile in use for each receive queue.  This
was instrumental in debugging issues found with DIM and ensuring that
the profiles we expect to use are the profiles being used.
Signed-off-by: NAndy Gospodarek <gospo@broadcom.com>
Signed-off-by: NMichael Chan <michael.chan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Testing with DIM enabled on older kernels indicated that firmware calls
were slower than expected.  More detailed analysis indicated that the
default 25us delay was higher than necessary.  Reducing the time spend in
usleep_range() for the first several calls would reduce the overall
latency of firmware calls on newer Intel processors.
Signed-off-by: NAndy Gospodarek <gospo@broadcom.com>
Signed-off-by: NMichael Chan <michael.chan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This keeps the RING_IDLE flag set in hardware for higher coalesce
settings by default and improved latency.
Signed-off-by: NAndy Gospodarek <gospo@broadcom.com>
Signed-off-by: NMichael Chan <michael.chan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Firmware does not allow the operation and would return failure, causing
a warning in dmesg.  So check for VF and disallow it in the driver.
Signed-off-by: NMichael Chan <michael.chan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add counters to display sum of rx/tx_discard_pkts of all rings as
function level statistics via ethtool.
Signed-off-by: NVasundhara Volam <vasundhara-v.volam@broadcom.com>
Signed-off-by: NMichael Chan <michael.chan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Replace switch statements printing different messages for every ring type
with a common message.
Signed-off-by: NMichael Chan <michael.chan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Older firmware will reject this call and cause an error message to
be printed by the VF driver.
Signed-off-by: NMichael Chan <michael.chan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Firmware messages that are forwarded from PF to VFs are encapsulated.
The size of these encapsulated messages must not exceed the maximum
defined message size.  Add appropriate checks to avoid oversize
messages.  Firmware messages may be expanded in future specs and
this will provide some guardrails to avoid data corruption.
Signed-off-by: NMichael Chan <michael.chan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Initially, the MQPRIO TCs are mapped 1:1 directly to the hardware
queues.  Some of these hardware queues are configured to be lossless.
When PFC is enabled on one of more TCs, we now need to remap the
TCs that have PFC enabled to the lossless hardware queues.

After remapping, we need to close and open the NIC for the new
mapping to take effect.  We also need to reprogram all ETS parameters.
Signed-off-by: NMichael Chan <michael.chan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The current driver maps MQPRIO traffic classes directly 1:1 to the
internal hardware queues (TC0 maps to hardware queue 0, etc).  This
direct mapping requires the internal hardware queues to be reconfigured
from lossless to lossy and vice versa when necessary.  This
involves reconfiguring internal buffer thresholds which is
disruptive and not always reliable.

Implement a new scheme to map TCs to internal hardware queues by
matching up their PFC requirements.  This will eliminate the need
to reconfigure a hardware queue internal buffers at run time.  After
remapping, the NIC is closed and opened for the new TC to hardware
queues to take effect.

This patch only adds the basic mapping logic.
Signed-off-by: NMichael Chan <michael.chan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The calls up from the napi poll reading the receive ring had many
places where an argument was being recreated. I.e the caller already
had the value and wasn't passing it, then the callee would use
known relationship to determine the same value. Simpler and faster
to just pass arguments needed.

Also, add const in a couple places where message is being only read.
Signed-off-by: NStephen Hemminger <sthemmin@microsoft.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Marcelo Ricardo Leitner says:

====================
sctp: refactor MTU handling

Currently MTU handling is spread over SCTP stack. There are multiple
places doing same/similar calculations and updating them is error prone
as one spot can easily be left out.

This patchset converges it into a more concise and consistent code. In
general, it moves MTU handling from functions with bigger objectives,
such as sctp_assoc_add_peer(), to specific functions.

It's also a preparation for the next patchset, which removes the
duplication between sctp_make_op_error_space and
sctp_make_op_error_fixed and relies on sctp_mtu_payload introduced here.

More details on each patch.
====================
Reviewed-by: NXin Long <lucien.xin@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

RFC 6458 Section 8.1.16 says that setting MAXSEG as 0 means that the user
is not limiting it, and not that it should set to the *current* maximum,
as we are doing.

This patch thus allow setting it as 0, effectively removing the user
limit.
Signed-off-by: NMarcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When setting SCTP_MAXSEG sock option, it should consider which kind of
data chunk is being used if the asoc is already available, so that the
limit better reflect reality.
Signed-off-by: NMarcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

sctp_sendmsg() could trigger PMTU updates even when PMTU_DISABLED was
set, as pmtu_pending could be set unconditionally during icmp handling
if the socket was in use by the application.

This patch fixes it by checking for PMTU_DISABLED when handling such
deferred updates.
Signed-off-by: NMarcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

sctp_transport_route currently is very similar to sctp_transport_pmtu plus
a few other bits.

This patch reuses sctp_transport_pmtu in sctp_transport_route and removes
the duplicated code.

Also, as all calls to sctp_transport_route were forcing the dst release
before calling it, let's just include such release too.
Signed-off-by: NMarcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

We are now keeping the MTU information synced between asoc, transport
and dst, which makes the check at sctp_packet_config() not needed
anymore. As it was the sole caller to this function, lets remove it.
Signed-off-by: NMarcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Which makes sure that the MTU respects the minimum value of
SCTP_DEFAULT_MINSEGMENT and that it is correctly aligned.
Signed-off-by: NMarcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

No need for this helper.
Signed-off-by: NMarcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

and avoid the open-coded versions of it.

Now sctp_datamsg_from_user can just re-use asoc->frag_point as it will
always be updated.
Signed-off-by: NMarcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When given a MTU, this function calculates how much payload we can carry
on it. Without a MTU, it calculates the amount of header overhead we
have.

So that when we have extra overhead, like the one added for IP options
on SELinux patches, it is easier to handle it.
Signed-off-by: NMarcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

All changes to asoc PMTU should now go through this wrapper, making it
easier to track them and to do other actions upon it.
Signed-off-by: NMarcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

As noticed by Xin Long, the if() here is always true as PMTU can never
be 0.
Reported-by: NXin Long <lucien.xin@gmail.com>
Signed-off-by: NMarcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

There was only one case that sctp_assoc_add_peer couldn't handle, which
is when SPP_PMTUD_DISABLE is set and pathmtu not initialized.
So add this situation to sctp_transport_route and reuse what was
already in there.
Signed-off-by: NMarcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This value is not used anywhere in the code. In essence it is a
duplicate of SCTP_DEFAULT_MINSEGMENT, which is used by the stack.

SCTP_MIN_PMTU value makes more sense, but we should not change to it now
as it would risk breaking applications.

So this patch removes SCTP_MIN_PMTU and adjust the comment above it.
Signed-off-by: NMarcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

A vti6 interface can carry IPv4 packets too.
Signed-off-by: NStefano Brivio <sbrivio@redhat.com>
Reviewed-by: NXin Long <lucien.xin@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

In tcp_select_initial_window(), we only set rcv_wnd to
tcp_default_init_rwnd() if current mss > (1 << wscale). Otherwise,
rcv_wnd is kept at the full receive space of the socket which is a
value way larger than tcp_default_init_rwnd().
With larger initial rcv_wnd value, receive buffer autotuning logic
takes longer to kick in and increase the receive buffer.

In a TCP throughput test where receiver has rmem[2] set to 125MB
(wscale is 11), we see the connection gets recvbuf limited at the
beginning of the connection and gets less throughput overall.
Signed-off-by: NWei Wang <weiwan@google.com>
Acked-by: NEric Dumazet <edumazet@google.com>
Acked-by: NSoheil Hassas Yeganeh <soheil@google.com>
Acked-by: NYuchung Cheng <ycheng@google.com>
Acked-by: NNeal Cardwell <ncardwell@google.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Ursula Braun says:

====================
smc fixes from 2018-04-17 - v3

in the mean time we challenged the benefit of these CLC handshake
optimizations for the sockopts TCP_NODELAY and TCP_CORK.
We decided to give up on them for now, since SMC still works
properly without.
There is now version 3 of the patch series with patches 2-4 implementing
sockopts that require special handling in SMC.

Version 3 changes
   * no deferring of setsockopts TCP_NODELAY and TCP_CORK anymore
   * allow fallback for some sockopts eliminating SMC usage
   * when setting TCP_NODELAY always enforce data transmission
     (not only together with corked data)

Version 2 changes of Patch 2/4 (and 3/4):
   * return error -EOPNOTSUPP for TCP_FASTOPEN sockopts
   * fix a kernel_setsockopt() usage bug by switching parameter
     variable from type "u8" to "int"
   * add return code validation when calling kernel_setsockopt()
   * propagate a setsockopt error on the internal CLC socket
     to the SMC socket.
====================
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

If sockopt TCP_DEFER_ACCEPT is set, the accept is delayed till
data is available.
Signed-off-by: NUrsula Braun <ubraun@linux.ibm.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Setting sockopt TCP_NODELAY or resetting sockopt TCP_CORK
triggers data transfer.

For a corked SMC socket RDMA writes are deferred, if there is
still sufficient send buffer space available.
Signed-off-by: NUrsula Braun <ubraun@linux.ibm.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Several TCP sockopts do not work for SMC. One example are the
TCP_FASTOPEN sockopts, since SMC-connection setup is based on the TCP
three-way-handshake.
If the SMC socket is still in state SMC_INIT, such sockopts trigger
fallback to TCP. Otherwise an error is returned.
Signed-off-by: NUrsula Braun <ubraun@linux.ibm.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The struct smc_cdc_msg must be defined as packed so the
size is 44 bytes.
And change the structure size check so sizeof is checked.
Signed-off-by: NKarsten Graul <kgraul@linux.ibm.com>
Signed-off-by: NUrsula Braun <ubraun@linux.ibm.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

After many years of having a ~30 line copyright and license header to our
source files, we are finally able to reduce that to one line with the
advent of the SPDX identifier.

Also caught a few files missing the SPDX license identifier, so fixed
them up.
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
Acked-by: NShannon Nelson <shannon.nelson@oracle.com>
Acked-by: NRichard Cochran <richardcochran@gmail.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

kbuild test robot says:

  >coccinelle warnings: (new ones prefixed by >>)
  >>> net/core/dev.c:1588:2-3: Unneeded semicolon

So, let's remove it.
Reported-by: Nkbuild test robot <lkp@intel.com>
Signed-off-by: NKirill Tkhai <ktkhai@virtuozzo.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Commit c40e89fd ("geneve: configure MTU based on a lower device") added
an IS_ENABLED(CONFIG_IPV6) to geneve, leading to the following link error
with CONFIG_GENEVE=y and CONFIG_IPV6=m:

drivers/net/geneve.o: In function `geneve_link_config':
geneve.c:(.text+0x14c): undefined reference to `rt6_lookup'

Fix this by adding a Kconfig dependency and forcing GENEVE to be a module
when IPV6 is a module.

Fixes: c40e89fd ("geneve: configure MTU based on a lower device")
Signed-off-by: NTobias Regnery <tobias.regnery@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Julian Wiedmann says:

====================
s390/net: updates 2018-04-26

please apply the following patches to net-next. There's the usual
cleanups & small improvements, and Kittipon adds HW offload support
for IPv6 checksumming.
====================
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

If READ MAC fails to fetch a valid MAC address, allow some more device
types (IQD and z/VM OSD) to fall back to a random address.
Also use eth_hw_addr_random(), for indicating to userspace that the
address type is NET_ADDR_RANDOM.

Note that while z/VM has various protection schemes to prohibit
custom addresses on its NICs, they are all optional. So we should at
least give it a try.
Signed-off-by: NJulian Wiedmann <jwi@linux.vnet.ibm.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>