Add a protocol argument to the VLAN packet tagging functions. In case of HW
tagging, we need that protocol available in the ndo_start_xmit functions,
so it is stored in a new field in the skb. The new field fits into a hole
(on 64 bit) and doesn't increase the sks's size.
Signed-off-by: NPatrick McHardy <kaber@trash.net>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Make the encapsulation protocol value a property of VLAN devices and change
the device lookup functions to take the protocol value into account.
Signed-off-by: NPatrick McHardy <kaber@trash.net>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Change the rx_{add,kill}_vid callbacks to take a protocol argument in
preparation of 802.1ad support. The protocol argument used so far is
always htons(ETH_P_8021Q).
Signed-off-by: NPatrick McHardy <kaber@trash.net>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Rename the hardware VLAN acceleration features to include "CTAG" to indicate
that they only support CTAGs. Follow up patches will introduce 802.1ad
server provider tagging (STAGs) and require the distinction for hardware not
supporting acclerating both.
Signed-off-by: NPatrick McHardy <kaber@trash.net>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch adds base support for new i354 devices.  Loopback test is
unsupported for this release.
Signed-off-by: NCarolyn Wyborny <carolyn.wyborny@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Add support for spoofchk configuration per VF via iproute2 tool.
Signed-off-by: NLior Levy <lior.levy@intel.com>
Tested-by: NSibai Li <sibai.li@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

On EEE-capable devices, query the PHY to determine what the link partner is
advertising.
Signed-off-by: NMatthew Vick <matthew.vick@intel.com>
Tested-by: NAaron Brown <aaron.f.brown@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Aligns the multi-line code comments with the desired style for the
networking tree.  Also cleaned up whitespace issues found during the
cleanup of code comments (i.e. remove unnecessary blank lines,
use tabs where possible, properly wrap lines and keep strings on a
single line)
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
Tested-by: NAaron Brown <aaron.f.brown@intel.com>

This patch fixes sparse warnings on function pointers that are not
defined as static.
Reported-by: NFengguang Wu <fengguang.wu@intel.com>
Signed-off-by: NAkeem G Abodunrin <akeem.g.abodunrin@intel.com>
Tested-by: NAaron Brown <aaron.f.brown@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

It turns out that the InterruptThrottleRate module parameter was only
having the effect of locking the ITR at the starting ITR value. This was
because the values stored in rx_itr_setting and tx_itr_setting were being
ignored when configuring the initial itr_val of the q_vector.
Signed-off-by: NAlexander Duyck <alexander.h.duyck@intel.com>
Tested-by: NAaron Brown <aaron.f.brown@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

We only need the adapter pointer in the case of ptp.  As such we can pull the
adapter out of the main path and place it inside the if statement to avoid
the temptation of accessing the adapter pointer in the fast path.
Signed-off-by: NAlexander Duyck <alexander.h.duyck@intel.com>
Tested-by: NAaron Brown <aaron.f.brown@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

We were incorrectly checking the entire frag_off field when we only wanted the
fragment offset.  As a result we were not pulling in TCP headers when the DNF
flag was set.

To correct that we will now check for frag off using the IP_OFFSET mask.
Signed-off-by: NAlexander Duyck <alexander.h.duyck@intel.com>
Tested-by: NAaron Brown <aaron.f.brown@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This patch fixes code and comments as identified in the driver.
Signed-off-by: NAkeem G Abodunrin <akeem.g.abodunrin@intel.com>
Tested-by: NAaron Brown <aaron.f.brown@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Based on original patch from Aurélien Guillaume <footplus@gmail.com>
This patch adds support to turn on I2C, with sfp cage powered.

CC: Aurélien Guillaume <footplus@gmail.com>
Signed-off-by: NAkeem G Abodunrin <akeem.g.abodunrin@intel.com>
Tested-by: NAaron Brown <aaron.f.brown@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This patch adds support to read and export SFF-8472/8079 (SFP data)
over i2c, through Ethtool.

v2: Changed implementation to accommodate any offset within SFF module
    length boundary.
Reported-by: NAurélien Guillaume <footplus@gmail.com>
CC: Aurélien Guillaume <footplus@gmail.com>
CC: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: NAkeem G Abodunrin <akeem.g.abodunrin@intel.com>
Tested-by: NAaron Brown <aaron.f.brown@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This patch adds support for 100base-fx SFP and report proper link speed/duplex
via Ethtool.

v2: fix smatch warnings

CC: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: NAkeem G Abodunrin <akeem.g.abodunrin@intel.com>
Tested-by: NAaron Brown <aaron.f.brown@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Add some empty static inlines instead to make
the code more readable.
Signed-off-by: NJoe Perches <joe@perches.com>
Tested-by: NPhil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This patch adds software support for WoL for the 82599 SFP+ LOM device,
(ID 0x8976)
Signed-off-by: NJacob Keller <jacob.e.keller@intel.com>
Tested-by: NPhil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

During shutdown it's possible for __dev_close() (which holds
rtnl_lock) to clear the __LINK_STATE_START bit, and for ixgbe
to then read that bit (without holding rtnl_lock), and then
not fail to free irqs, etc. The result is a crash like this:

------------[ cut here ]------------
kernel BUG at drivers/pci/msi.c:313!
invalid opcode: 0000 [#1] SMP
last sysfs file: /sys/devices/system/cpu/cpu3/cache/index2/shared_cpu_map
CPU 1
Pid: 5910, comm: reboot Tainted: P           ----------------   2.6.32 #1 empty
RIP: 0010:[<ffffffff81305c2b>]  [<ffffffff81305c2b>] free_msi_irqs+0x11b/0x130
RSP: 0018:ffff880185c9bc88  EFLAGS: 00010282
RAX: ffff880219f58bc0 RBX: ffff88021ac53b00 RCX: 0000000000000000
RDX: 0000000000000001 RSI: 0000000000000246 RDI: 000000000000004a
RBP: ffff880185c9bcc8 R08: 0000000000000002 R09: 0000000000000106
R10: 0000000000000000 R11: 0000000000000006 R12: ffff88021e524778
R13: 0000000000000001 R14: ffff88021e524000 R15: 0000000000000000
FS:  00007f90821b7700(0000) GS:ffff880028220000(0000) knlGS:0000000000000000
CS:  0010 DS: 0000 ES: 0000 CR0: 000000008005003b
CR2: 00007f90818bd010 CR3: 0000000132c64000 CR4: 00000000000006e0
DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
DR3: 0000000000000000 DR6: 00000000ffff0ff0 DR7: 0000000000000400
Process reboot (pid: 5910, threadinfo ffff880185c9a000, task ffff88021bf04a80)
Stack:
 ffff880185c9bc98 000000018130529d ffff880185c9bcc8 ffff88021e524000
<0> 0000000000000004 ffff88021948c700 0000000000000000 ffff880185c9bda7
<0> ffff880185c9bce8 ffffffff81305cbd ffff880185c9bce8 ffff88021948c700
Call Trace:
 [<ffffffff81305cbd>] pci_disable_msix+0x3d/0x50
 [<ffffffffa00501d5>] ixgbe_reset_interrupt_capability+0x65/0x90 [ixgbe]
 [<ffffffffa00512f6>] ixgbe_clear_interrupt_scheme+0xb6/0xd0 [ixgbe]
 [<ffffffffa005330b>] __ixgbe_shutdown+0x5b/0x200 [ixgbe]
 [<ffffffffa00534ca>] ixgbe_shutdown+0x1a/0x60 [ixgbe]
 [<ffffffff812f6c7c>] pci_device_shutdown+0x2c/0x50
 [<ffffffff813727fb>] device_shutdown+0x4b/0x160
 [<ffffffff8107d98c>] kernel_restart_prepare+0x2c/0x40
 ehci timer_action, mod_timer io_watchdog
 [<ffffffff8107d9e6>] kernel_restart+0x16/0x60
 [<ffffffff8107dbfd>] sys_reboot+0x1ad/0x200
 [<ffffffff811676cf>] ? __d_free+0x3f/0x60
 [<ffffffff81167748>] ? d_free+0x58/0x60
 [<ffffffff8116f7c0>] ? mntput_no_expire+0x30/0x100
 [<ffffffff81152b11>] ? __fput+0x191/0x200
 [<ffffffff816565fe>] ? do_page_fault+0x3e/0xa0
 [<ffffffff8100b132>] system_call_fastpath+0x16/0x1b
Code: 4c 89 ef e8 98 8c e3 ff 4d 39 f4 48 8b 43 10 75 cf 48 83 c4 18 5b 41 5c
41 5d 41 5e 41 5f c9 c3 49 8b 7d 20 e8 07 5a d3 ff eb c9 <0f> 0b 0f 1f 00 eb fb
66 66 66 66 66 2e 0f 1f 84 00 00 00 00 00
 ehci timer_action, mod_timer io_watchdog
RIP  [<ffffffff81305c2b>] free_msi_irqs+0x11b/0x130
 RSP <ffff880185c9bc88>
---[ end trace 27de882a0fe75593 ]---

(This was seen on a pretty old kernel/driver, but looks like
the same bug is still possible.)

Signed-off-by: <akepner@riverbed.com>
Tested-by: NPhil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

There is nothing in the driver that requires <asm/coldfire.h> and
<asm/mcfsim.h>.
Signed-off-by: NFabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Bump the version number reflect the corresponding functionality in the
out of tree driver.
Signed-of-by: NDon Skidmore <donald.c.skidmore@intel.com>
Tested-by: NPhil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

We reset during the shutdown path which will reset AUTOC register.  This
would change LMS to 10G.  If we were currently linked at 1G we will lose
link, which is a bad thing if we wanted WoL to work.  For the fix I needed
to know if WoL is supported so I created a new bool in the ixgbe_hw struct.
If this is set we will not allow the reset to change the current LMS value
in AUTOC.
Signed-off-by: NDon Skidmore <donald.c.skidmore@intel.com>
Tested-by: NPhil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

We were only turning the laser on when the adapter was up.  This
causes issues for those who wanted to access the MNG FW while the
port was in a down state.  This patch makes sure the laser is turned
on in probe and remain up even after the port is brought down.
Signed-off-by: NDon Skidmore <donald.c.skidmore@intel.com>
Tested-by: NPhil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This patch modifies the driver to enable certain devices, which have an internal
switch, to read data from the physical slot rather than reading data from the
internal switch. The internal switch will always report the same PCI width and
speed, which is not useful compared to knowing the width and speed of the slot
the physical card is plugged into.
Signed-off-by: NJacob Keller <jacob.e.keller@intel.com>
Tested-by: NPhil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This patch cleans up ixgbe_get_bus_info_generic to call some conversion
functions, which are used also in a follow on patch that needs to convert
between the link_status PCIe config values into ixgbe's internal enum
representations.
Signed-off-by: NJacob Keller <jacob.e.keller@intel.com>
Tested-by: NPhil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This patch adds support for displaying PCIe Gen3 link speed, which was
previously missing from the driver.
Signed-off-by: NJacob Keller <jacob.e.keller@intel.com>
Tested-by: NPhil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

The check for PAGE_SIZE is pointless now that the default configuration is to
allocate 32K for all buffers.  Since the Tx descriptor limit is 16K we can
just drop the check and always compare the descriptors to the maximum size
supported.
Signed-off-by: NAlexander Duyck <alexander.h.duyck@intel.com>
Tested-by: NPhil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Make the calculation of eerd consistent between the read and write functions
by using | instead of + for IXGBE_EEPROM_RW_REG_START
Reported-by: NDan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: NEmil Tantilov <emil.s.tantilov@intel.com>
Tested-by: NPhil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

We were incorrectly checking the entire frag_off field when we only wanted the
fragment offset.  As a result we were not pulling in TCP headers when the DNF
flag was set.

To correct that we will now check for frag off using the IP_OFFSET mask.
Signed-off-by: NAlexander Duyck <alexander.h.duyck@intel.com>
Tested-by: NPhil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

commit 7b7a2bbb (atl1: Remove unneeded PM_OPS definitions) removed the
definition of atl1_suspend for the !CONFIG_PM_SLEEP case.

So only call atl1_suspend() when CONFIG_PM_SLEEP is defined and fix the
following build error from randconfig:

drivers/net/ethernet/atheros/atlx/atl1.c: In function 'atl1_shutdown':
drivers/net/ethernet/atheros/atlx/atl1.c:2888:2: error: implicit declaration of function 'atl1_suspend' [-Werror=implicit-function-declaration]
Reported-by: Nkbuild test robot <fengguang.wu@intel.com>
Signed-off-by: NFabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Using SIMPLE_DEV_PM_OPS can make the code smaller and simpler.

Also change CONFIG_PM to CONFIG_PM_SLEEP.
Signed-off-by: NFabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

If we can't _up() after changing the MTU, report the actual error instead
of -ENOMEM. It can be really misleading cause pch_gbe is usually used in
scenarios where the memory amount is really small, and thus hiding the
real cause.
Signed-off-by: NVeaceslav Falico <vfalico@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

the work has been scheduled from interrupt, and not been
cancelled when the driver is unloaded, which doesn't remove
the work item from the global workqueue. call the
cancel_work_sync when the driver is removed (rmmod'ed).

Cc: Sriram <srk@ti.com>
Cc: Cyril Chemparathy <cyril@ti.com>
Cc: Vinay Hegde <vinay.hegde@ti.com>
Signed-off-by: NDevendra Naga <devendra.aaru@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

SIMPLE_DEV_PM_OPS macro can handle !CONFIG_PM_SLEEP case nicely, so there is no
need to define PM_OPS for both CONFIG_PM_SLEEP and !CONFIG_PM_SLEEP cases.

Remove the unneeded definitions.

Cc: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: NFabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

SIMPLE_DEV_PM_OPS macro can handle !CONFIG_PM_SLEEP case nicely, so there is no
need to define PM_OPS for both CONFIG_PM_SLEEP and !CONFIG_PM_SLEEP cases.

Remove the unneeded definitions.
Signed-off-by: NFabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

SIMPLE_DEV_PM_OPS macro can handle !CONFIG_PM_SLEEP case nicely, so there is no
need to define PM_OPS for both CONFIG_PM_SLEEP and !CONFIG_PM_SLEEP cases.

Remove the unneeded definitions.

Cc: Nithin Nayak Sujir <nsujir@broadcom.com>
Signed-off-by: NFabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

SIMPLE_DEV_PM_OPS macro can handle !CONFIG_PM_SLEEP case nicely, so there is no
need to define PM_OPS for both CONFIG_PM_SLEEP and !CONFIG_PM_SLEEP cases.

Remove the unneeded definitions.

Cc: Jay Cliburn <jcliburn@gmail.com>
Signed-off-by: NFabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The first backtrace appears on tx path with DMA mapping operations debug
enabled.

[  345.637919] ------------[ cut here ]------------
[  345.637971] WARNING: at lib/dma-debug.c:937 check_unmap+0x4df/0x910()
[  345.637977] Hardware name: System Name
[  345.637987] sis900 0000:00:01.1: DMA-API: device driver failed to check map error[device address=0x000000000d4aed02] [si
ze=60 bytes] [mapped as single]
[  345.637993] Modules linked in: bridge stp llc dmfe sundance 3c59x sis900
[  345.638022] Pid: 0, comm: swapper Not tainted 3.9.0-rc6+ #4
[  345.638028] Call Trace:
[  345.638042]  [<c122097f>] ? check_unmap+0x4df/0x910
[  345.638059]  [<c102b19c>] warn_slowpath_common+0x7c/0xa0
[  345.638070]  [<c122097f>] ? check_unmap+0x4df/0x910
[  345.638081]  [<c102b23e>] warn_slowpath_fmt+0x2e/0x30
[  345.638092]  [<c122097f>] check_unmap+0x4df/0x910
[  345.638107]  [<c100bfeb>] ? save_stack_trace+0x2b/0x50
[  345.638120]  [<c107238e>] ? mark_lock+0x31e/0x5d0
[  345.638132]  [<c1072b2c>] ? __lock_acquire+0x4ec/0x7d0
[  345.638143]  [<c1220f6d>] debug_dma_unmap_page+0x6d/0x80
[  345.638166]  [<cf834dec>] sis900_interrupt+0x49c/0x860 [sis900]
[  345.638195]  [<c1094b73>] handle_irq_event_percpu+0x43/0x1c0
[  345.638206]  [<c1094d1e>] ? handle_irq_event+0x2e/0x60
[  345.638217]  [<c1094d27>] handle_irq_event+0x37/0x60
[  345.638235]  [<c10973f0>] ? irq_set_chip_data+0x40/0x40
[  345.638246]  [<c1097442>] handle_level_irq+0x52/0xa0
[  345.638251]  <IRQ>  [<c1003629>] ? do_IRQ+0x39/0xa0
[  345.638293]  [<c1484631>] ? common_interrupt+0x31/0x36
[  345.638347]  [<d08c2c52>] ? br_flood_forward+0x12/0x20 [bridge]
[  345.638364]  [<d08c2d40>] ? br_dev_queue_push_xmit+0x60/0x60 [bridge]
[  345.638381]  [<d08c3b2b>] ? br_handle_frame_finish+0x25b/0x280 [bridge]
[  345.638399]  [<d08c3ce3>] ? br_handle_frame+0x193/0x290 [bridge]
[  345.638416]  [<d08c3b50>] ? br_handle_frame_finish+0x280/0x280 [bridge]
[  345.638431]  [<c13b3c87>] ? __netif_receive_skb_core+0x1d7/0x710
[  345.638442]  [<c13b3b19>] ? __netif_receive_skb_core+0x69/0x710
[  345.638454]  [<c13b41e1>] ? __netif_receive_skb+0x21/0x70
[  345.638464]  [<c13b42b5>] ? process_backlog+0x85/0x130
[  345.638476]  [<c13b4bbb>] ? net_rx_action+0xfb/0x1d0
[  345.638497]  [<c1032768>] ? __do_softirq+0xa8/0x1f0
[  345.638527]  [<c147daad>] ? _raw_spin_unlock+0x1d/0x20
[  345.638538]  [<c10038c0>] ? handle_irq+0x20/0xd0
[  345.638550]  [<c1032f27>] ? irq_exit+0x97/0xa0
[  345.638560]  [<c1003632>] ? do_IRQ+0x42/0xa0
[  345.638580]  [<c104d003>] ? hrtimer_start+0x23/0x30
[  345.638580]  [<c1484631>] ? common_interrupt+0x31/0x36
[  345.638580]  [<c1008703>] ? default_idle+0x33/0xc0
[  345.638580]  [<c10086ac>] ? cpu_idle+0x4c/0x70
[  345.638580]  [<c14787e0>] ? rest_init+0xa0/0xb0
[  345.638580]  [<c1478740>] ? reciprocal_value+0x50/0x50
[  345.638580]  [<c16b5bcf>] ? start_kernel+0x28f/0x320
[  345.638580]  [<c16b54e0>] ? repair_env_string+0x60/0x60
[  345.638580]  [<c16b5269>] ? i386_start_kernel+0x39/0xa0
[  345.638580] ---[ end trace a244264b69b8a7ae ]---
[  345.638580] Mapped at:
[  345.638580]  [<c1221c65>] debug_dma_map_page+0x65/0x110
[  345.638580]  [<cf8355a9>] sis900_start_xmit+0x129/0x210 [sis900]
[  345.638580]  [<c13b2527>] dev_hard_start_xmit+0x1b7/0x530
[  345.638580]  [<c13cc32e>] sch_direct_xmit+0x8e/0x280
[  345.638580]  [<c13b4e39>] dev_queue_xmit+0x1a9/0x5b0
Signed-off-by: NDenis Kirjanov <kda@linux-powerpc.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Fix to return a negative error code from the error handling
case instead of 0, as returned elsewhere in this function.

Original-idea-by: <yongjun_wei@trendmicro.com.cn>
Signed-off-by: NNicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Remove unnecessary macros that duplicate generic
kernel functions.

When a struct net_device is available:

Convert printks to netdev_<level>
Convert netif_msg_<foo> and ugeth_<level> to netif_<level>

Add pr_fmt.  Standardize on newlines at end of format.
Remove some duplicated newlines from output.
Coalesce formats.
Signed-off-by: NJoe Perches <joe@perches.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>