An integer overflow is possible in dev_map_bitmap_size() when
calculating the BITS_TO_LONG logic which becomes, after macro
replacement,

	(((n) + (d) - 1)/ (d))

where 'n' is a __u32 and 'd' is (8 * sizeof(long)). To avoid
overflow cast to u64 before arithmetic.
Reported-by: NRichard Weinberger <richard@nod.at>
Acked-by: NDaniel Borkmann <daniel@iogearbox.net>
Signed-off-by: NJohn Fastabend <john.fastabend@gmail.com>
Acked-by: NAlexei Starovoitov <ast@kernel.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Igor Russkikh says:

====================
net: aquantia: Atlantic driver 10/2017 updates

This patchset fixes various issues in driver,
improves parameters for better performance on 10Gbit link
====================
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Default Tx rates cause very long ISR delays on Tx.
0xff is 510us delay, giving only ~ 2000 interrupts per seconds for
Tx rings cleanup. With these settings udp tx rate was never higher than
~800Mbps on a single stream. Changing min delay to 0xF makes it
way better with ~6Gbps

TCP stream performance is almost unaffected by this change, since LSO
optimizations play important role.

CPU load is affected insignificantly by this change.
Signed-off-by: NPavel Belous <pavel.belous@aquantia.com>
Signed-off-by: NIgor Russkikh <igor.russkikh@aquantia.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Aquantia NIC allows both TX and RX interrupt throttle rate (ITR)
management, but this was used in a very limited way via predefined
values. This patch allows to setup ITR default values via module
command line arguments and via standard ethtool coalescing settings.
Signed-off-by: NPavel Belous <pavel.belous@aquantia.com>
Signed-off-by: NIgor Russkikh <igor.russkikh@aquantia.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

That may lead to mmio resource leakage.
Signed-off-by: NPavel Belous <pavel.belous@aquantia.com>
Signed-off-by: NIgor Russkikh <igor.russkikh@aquantia.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

There is no much practical use from having MSIX vectors more that number
of cpus, thus cap this first with preconfigured limit, then with number
of cpus online.
Signed-off-by: NPavel Belous <pavel.belous@aquantia.com>
Signed-off-by: NIgor Russkikh <igor.russkikh@aquantia.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When doing ifconfig down/up, driver did not reported carrier_off neither
in nic_stop nor in nic_start. That caused link to be visible as "up"
during couple of seconds immediately after "ifconfig up".
Signed-off-by: NPavel Belous <pavel.belous@aquantia.com>
Signed-off-by: NIgor Russkikh <igor.russkikh@aquantia.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Queue stat strings are cleaned up, duplicate stat name strings removed,
queue restarts counter added
Signed-off-by: NPavel Belous <pavel.belous@aquantia.com>
Signed-off-by: NIgor Russkikh <igor.russkikh@aquantia.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Internal statistics system on chip never gets reset until hardware
reboot. This is quite inconvenient in terms of ethtool statistics usage.

This patch implements incremental statistics update inside of
service callback.

Upon nic initialization, first request is done to fetch
initial stat data, current collected stat data gets cleared.
Internal statistics mailbox readout is improved to save space and
increase readability
Signed-off-by: NPavel Belous <pavel.belous@aquantia.com>
Signed-off-by: NIgor Russkikh <igor.russkikh@aquantia.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

In the UDP code there are two leftover error messages with very few meaning.
Replace them with a more descriptive error message as some users
reported them as "strange network error".
Signed-off-by: NMatteo Croce <mcroce@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

On big-endian machines, functions converting between tunnel ID
and VNI use the three LSBs of tunnel ID storage to map VNI.

The comparison function eq_tun_id_and_vni(), on the other hand,
attempted to map the VNI from the three MSBs. Fix it by using
the same check implemented on LE, which maps VNI from the three
LSBs of tunnel ID.

Fixes: 2e0b26e1 ("geneve: Optimize geneve device lookup.")
Signed-off-by: NStefano Brivio <sbrivio@redhat.com>
Reviewed-by: NJakub Sitnicki <jkbs@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Merge tag 'linux-can-fixes-for-4.14-20171019' of git://git.kernel.org/pub/scm/linux/kernel/git/mkl/linux-can

Marc Kleine-Budde says:

====================
pull-request: can 2017-10-19

this is a pull request of 11 patches for the upcoming 4.14 release.

There are 6 patches by ZHU Yi for the flexcan driver, that work around
the CAN error handling state transition problems found in various
incarnations of the flexcan IP core.

The patch by Colin Ian King fixes a potential NULL pointer deref in the
CAN broad cast manager (bcm). One patch by me replaces a direct deref of a RCU
protected pointer by rcu_access_pointer. My second patch adds missing
OOM error handling in af_can. A patch by Stefan Mätje for the esd_usb2
driver fixes the dlc in received RTR frames. And the last patch is by
Wolfgang Grandegger, it fixes a busy loop in the gs_usb driver in case
it runs out of TX contexts.
====================
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Without the patch, when hvs_open_connection() hasn't completely established
a connection (e.g. it has changed sk->sk_state to SS_CONNECTED, but hasn't
inserted the sock into the connected queue), vsock_stream_connect() may see
the sk_state change and return the connection to the userspace, and next
when the userspace closes the connection quickly, hvs_release() may not see
the connection in the connected queue; finally hvs_open_connection()
inserts the connection into the queue, but we won't be able to purge the
connection for ever.
Signed-off-by: NDexuan Cui <decui@microsoft.com>
Cc: K. Y. Srinivasan <kys@microsoft.com>
Cc: Haiyang Zhang <haiyangz@microsoft.com>
Cc: Stephen Hemminger <sthemmin@microsoft.com>
Cc: Vitaly Kuznetsov <vkuznets@redhat.com>
Cc: Cathy Avery <cavery@redhat.com>
Cc: Rolf Neugebauer <rolf.neugebauer@docker.com>
Cc: Marcelo Cerri <marcelo.cerri@canonical.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The length of GVI (GetVersionInfo) response packet should be 40 instead
of 36. This issue was found from /sys/kernel/debug/ncsi/eth0/stats.

 # ethtool --ncsi eth0 swstats
     :
 RESPONSE     OK       TIMEOUT  ERROR
 =======================================
 GVI          0        0        2

With this applied, no error reported on GVI response packets:

 # ethtool --ncsi eth0 swstats
     :
 RESPONSE     OK       TIMEOUT  ERROR
 =======================================
 GVI          2        0        0
Signed-off-by: NGavin Shan <gwshan@linux.vnet.ibm.com>
Signed-off-by: NSamuel Mendoza-Jonas <sam@mendozajonas.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The NCSI channel has been configured to provide service if its link
monitor timer is enabled, regardless of its state (inactive or active).
So the timeout event on the link monitor indicates the out-of-service
on that channel, for which a failover is needed.

This sets NCSI_DEV_RESHUFFLE flag to enforce failover on link monitor
timeout, regardless the channel's original state (inactive or active).
Also, the link is put into "down" state to give the failing channel
lowest priority when selecting for the active channel. The state of
failing channel should be set to active in order for deinitialization
and failover to be done.
Signed-off-by: NGavin Shan <gwshan@linux.vnet.ibm.com>
Signed-off-by: NSamuel Mendoza-Jonas <sam@mendozajonas.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When there are no NCSI channels probed, HWA (Hardware Arbitration)
mode is enabled. It's not correct because HWA depends on the fact:
NCSI channels exist and all of them support HWA mode. This disables
HWA when no channels are probed.
Signed-off-by: NGavin Shan <gwshan@linux.vnet.ibm.com>
Signed-off-by: NSamuel Mendoza-Jonas <sam@mendozajonas.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

ncsi_channel_monitor() misses stopping the channel monitor in several
places that it should, causing a WARN_ON_ONCE() to trigger when the
monitor is re-started later, eg:

[  459.040000] WARNING: CPU: 0 PID: 1093 at net/ncsi/ncsi-manage.c:269 ncsi_start_channel_monitor+0x7c/0x90
[  459.040000] CPU: 0 PID: 1093 Comm: kworker/0:3 Not tainted 4.10.17-gaca2fdd #140
[  459.040000] Hardware name: ASpeed SoC
[  459.040000] Workqueue: events ncsi_dev_work
[  459.040000] [<80010094>] (unwind_backtrace) from [<8000d950>] (show_stack+0x20/0x24)
[  459.040000] [<8000d950>] (show_stack) from [<801dbf70>] (dump_stack+0x20/0x28)
[  459.040000] [<801dbf70>] (dump_stack) from [<80018d7c>] (__warn+0xe0/0x108)
[  459.040000] [<80018d7c>] (__warn) from [<80018e70>] (warn_slowpath_null+0x30/0x38)
[  459.040000] [<80018e70>] (warn_slowpath_null) from [<803f6a08>] (ncsi_start_channel_monitor+0x7c/0x90)
[  459.040000] [<803f6a08>] (ncsi_start_channel_monitor) from [<803f7664>] (ncsi_configure_channel+0xdc/0x5fc)
[  459.040000] [<803f7664>] (ncsi_configure_channel) from [<803f8160>] (ncsi_dev_work+0xac/0x474)
[  459.040000] [<803f8160>] (ncsi_dev_work) from [<8002d244>] (process_one_work+0x1e0/0x450)
[  459.040000] [<8002d244>] (process_one_work) from [<8002d510>] (worker_thread+0x5c/0x570)
[  459.040000] [<8002d510>] (worker_thread) from [<80033614>] (kthread+0x124/0x164)
[  459.040000] [<80033614>] (kthread) from [<8000a5e8>] (ret_from_fork+0x14/0x2c)

This also updates the monitor instead of just returning if
ncsi_xmit_cmd() fails to send the get-link-status command so that the
monitor properly times out.

Fixes: e6f44ed6 "net/ncsi: Package and channel management"
Signed-off-by: NSamuel Mendoza-Jonas <sam@mendozajonas.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Correct the value of the HNCDSC AEN packet.
Fixes: 7a82ecf4 "net/ncsi: NCSI AEN packet handler"
Signed-off-by: NSamuel Mendoza-Jonas <sam@mendozajonas.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

syzkaller got crashes in packet_getsockopt() processing
PACKET_ROLLOVER_STATS command while another thread was managing
to change po->rollover

Using RCU will fix this bug. We might later add proper RCU annotations
for sparse sake.

In v2: I replaced kfree(rollover) in fanout_add() to kfree_rcu()
variant, as spotted by John.

Fixes: a9b63918 ("packet: rollover statistics")
Signed-off-by: NEric Dumazet <edumazet@google.com>
Cc: Willem de Bruijn <willemb@google.com>
Cc: John Sperbeck <jsperbeck@google.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

syzkaller found another bug in DCCP/TCP stacks [1]

For the reasons explained in commit ce105008 ("tcp/dccp: fix
ireq->pktopts race"), we need to make sure we do not access
ireq->opt unless we own the request sock.

Note the opt field is renamed to ireq_opt to ease grep games.

[1]
BUG: KASAN: use-after-free in ip_queue_xmit+0x1687/0x18e0 net/ipv4/ip_output.c:474
Read of size 1 at addr ffff8801c951039c by task syz-executor5/3295

CPU: 1 PID: 3295 Comm: syz-executor5 Not tainted 4.14.0-rc4+ #80
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 01/01/2011
Call Trace:
 __dump_stack lib/dump_stack.c:16 [inline]
 dump_stack+0x194/0x257 lib/dump_stack.c:52
 print_address_description+0x73/0x250 mm/kasan/report.c:252
 kasan_report_error mm/kasan/report.c:351 [inline]
 kasan_report+0x25b/0x340 mm/kasan/report.c:409
 __asan_report_load1_noabort+0x14/0x20 mm/kasan/report.c:427
 ip_queue_xmit+0x1687/0x18e0 net/ipv4/ip_output.c:474
 tcp_transmit_skb+0x1ab7/0x3840 net/ipv4/tcp_output.c:1135
 tcp_send_ack.part.37+0x3bb/0x650 net/ipv4/tcp_output.c:3587
 tcp_send_ack+0x49/0x60 net/ipv4/tcp_output.c:3557
 __tcp_ack_snd_check+0x2c6/0x4b0 net/ipv4/tcp_input.c:5072
 tcp_ack_snd_check net/ipv4/tcp_input.c:5085 [inline]
 tcp_rcv_state_process+0x2eff/0x4850 net/ipv4/tcp_input.c:6071
 tcp_child_process+0x342/0x990 net/ipv4/tcp_minisocks.c:816
 tcp_v4_rcv+0x1827/0x2f80 net/ipv4/tcp_ipv4.c:1682
 ip_local_deliver_finish+0x2e2/0xba0 net/ipv4/ip_input.c:216
 NF_HOOK include/linux/netfilter.h:249 [inline]
 ip_local_deliver+0x1ce/0x6e0 net/ipv4/ip_input.c:257
 dst_input include/net/dst.h:464 [inline]
 ip_rcv_finish+0x887/0x19a0 net/ipv4/ip_input.c:397
 NF_HOOK include/linux/netfilter.h:249 [inline]
 ip_rcv+0xc3f/0x1820 net/ipv4/ip_input.c:493
 __netif_receive_skb_core+0x1a3e/0x34b0 net/core/dev.c:4476
 __netif_receive_skb+0x2c/0x1b0 net/core/dev.c:4514
 netif_receive_skb_internal+0x10b/0x670 net/core/dev.c:4587
 netif_receive_skb+0xae/0x390 net/core/dev.c:4611
 tun_rx_batched.isra.50+0x5ed/0x860 drivers/net/tun.c:1372
 tun_get_user+0x249c/0x36d0 drivers/net/tun.c:1766
 tun_chr_write_iter+0xbf/0x160 drivers/net/tun.c:1792
 call_write_iter include/linux/fs.h:1770 [inline]
 new_sync_write fs/read_write.c:468 [inline]
 __vfs_write+0x68a/0x970 fs/read_write.c:481
 vfs_write+0x18f/0x510 fs/read_write.c:543
 SYSC_write fs/read_write.c:588 [inline]
 SyS_write+0xef/0x220 fs/read_write.c:580
 entry_SYSCALL_64_fastpath+0x1f/0xbe
RIP: 0033:0x40c341
RSP: 002b:00007f469523ec10 EFLAGS: 00000293 ORIG_RAX: 0000000000000001
RAX: ffffffffffffffda RBX: 0000000000718000 RCX: 000000000040c341
RDX: 0000000000000037 RSI: 0000000020004000 RDI: 0000000000000015
RBP: 0000000000000086 R08: 0000000000000000 R09: 0000000000000000
R10: 00000000000f4240 R11: 0000000000000293 R12: 00000000004b7fd1
R13: 00000000ffffffff R14: 0000000020000000 R15: 0000000000025000

Allocated by task 3295:
 save_stack_trace+0x16/0x20 arch/x86/kernel/stacktrace.c:59
 save_stack+0x43/0xd0 mm/kasan/kasan.c:447
 set_track mm/kasan/kasan.c:459 [inline]
 kasan_kmalloc+0xad/0xe0 mm/kasan/kasan.c:551
 __do_kmalloc mm/slab.c:3725 [inline]
 __kmalloc+0x162/0x760 mm/slab.c:3734
 kmalloc include/linux/slab.h:498 [inline]
 tcp_v4_save_options include/net/tcp.h:1962 [inline]
 tcp_v4_init_req+0x2d3/0x3e0 net/ipv4/tcp_ipv4.c:1271
 tcp_conn_request+0xf6d/0x3410 net/ipv4/tcp_input.c:6283
 tcp_v4_conn_request+0x157/0x210 net/ipv4/tcp_ipv4.c:1313
 tcp_rcv_state_process+0x8ea/0x4850 net/ipv4/tcp_input.c:5857
 tcp_v4_do_rcv+0x55c/0x7d0 net/ipv4/tcp_ipv4.c:1482
 tcp_v4_rcv+0x2d10/0x2f80 net/ipv4/tcp_ipv4.c:1711
 ip_local_deliver_finish+0x2e2/0xba0 net/ipv4/ip_input.c:216
 NF_HOOK include/linux/netfilter.h:249 [inline]
 ip_local_deliver+0x1ce/0x6e0 net/ipv4/ip_input.c:257
 dst_input include/net/dst.h:464 [inline]
 ip_rcv_finish+0x887/0x19a0 net/ipv4/ip_input.c:397
 NF_HOOK include/linux/netfilter.h:249 [inline]
 ip_rcv+0xc3f/0x1820 net/ipv4/ip_input.c:493
 __netif_receive_skb_core+0x1a3e/0x34b0 net/core/dev.c:4476
 __netif_receive_skb+0x2c/0x1b0 net/core/dev.c:4514
 netif_receive_skb_internal+0x10b/0x670 net/core/dev.c:4587
 netif_receive_skb+0xae/0x390 net/core/dev.c:4611
 tun_rx_batched.isra.50+0x5ed/0x860 drivers/net/tun.c:1372
 tun_get_user+0x249c/0x36d0 drivers/net/tun.c:1766
 tun_chr_write_iter+0xbf/0x160 drivers/net/tun.c:1792
 call_write_iter include/linux/fs.h:1770 [inline]
 new_sync_write fs/read_write.c:468 [inline]
 __vfs_write+0x68a/0x970 fs/read_write.c:481
 vfs_write+0x18f/0x510 fs/read_write.c:543
 SYSC_write fs/read_write.c:588 [inline]
 SyS_write+0xef/0x220 fs/read_write.c:580
 entry_SYSCALL_64_fastpath+0x1f/0xbe

Freed by task 3306:
 save_stack_trace+0x16/0x20 arch/x86/kernel/stacktrace.c:59
 save_stack+0x43/0xd0 mm/kasan/kasan.c:447
 set_track mm/kasan/kasan.c:459 [inline]
 kasan_slab_free+0x71/0xc0 mm/kasan/kasan.c:524
 __cache_free mm/slab.c:3503 [inline]
 kfree+0xca/0x250 mm/slab.c:3820
 inet_sock_destruct+0x59d/0x950 net/ipv4/af_inet.c:157
 __sk_destruct+0xfd/0x910 net/core/sock.c:1560
 sk_destruct+0x47/0x80 net/core/sock.c:1595
 __sk_free+0x57/0x230 net/core/sock.c:1603
 sk_free+0x2a/0x40 net/core/sock.c:1614
 sock_put include/net/sock.h:1652 [inline]
 inet_csk_complete_hashdance+0xd5/0xf0 net/ipv4/inet_connection_sock.c:959
 tcp_check_req+0xf4d/0x1620 net/ipv4/tcp_minisocks.c:765
 tcp_v4_rcv+0x17f6/0x2f80 net/ipv4/tcp_ipv4.c:1675
 ip_local_deliver_finish+0x2e2/0xba0 net/ipv4/ip_input.c:216
 NF_HOOK include/linux/netfilter.h:249 [inline]
 ip_local_deliver+0x1ce/0x6e0 net/ipv4/ip_input.c:257
 dst_input include/net/dst.h:464 [inline]
 ip_rcv_finish+0x887/0x19a0 net/ipv4/ip_input.c:397
 NF_HOOK include/linux/netfilter.h:249 [inline]
 ip_rcv+0xc3f/0x1820 net/ipv4/ip_input.c:493
 __netif_receive_skb_core+0x1a3e/0x34b0 net/core/dev.c:4476
 __netif_receive_skb+0x2c/0x1b0 net/core/dev.c:4514
 netif_receive_skb_internal+0x10b/0x670 net/core/dev.c:4587
 netif_receive_skb+0xae/0x390 net/core/dev.c:4611
 tun_rx_batched.isra.50+0x5ed/0x860 drivers/net/tun.c:1372
 tun_get_user+0x249c/0x36d0 drivers/net/tun.c:1766
 tun_chr_write_iter+0xbf/0x160 drivers/net/tun.c:1792
 call_write_iter include/linux/fs.h:1770 [inline]
 new_sync_write fs/read_write.c:468 [inline]
 __vfs_write+0x68a/0x970 fs/read_write.c:481
 vfs_write+0x18f/0x510 fs/read_write.c:543
 SYSC_write fs/read_write.c:588 [inline]
 SyS_write+0xef/0x220 fs/read_write.c:580
 entry_SYSCALL_64_fastpath+0x1f/0xbe

Fixes: e994b2f0 ("tcp: do not lock listener to process SYN packets")
Fixes: 079096f1 ("tcp/dccp: install syn_recv requests into ehash table")
Signed-off-by: NEric Dumazet <edumazet@google.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

John Fastabend says:

====================
sockmap fixes for net

The following implements a set of fixes for sockmap and changes the
API slightly in a few places to reduce preempt_disable/enable scope.
We do this here in net because it requires an API change and this
avoids getting stuck with legacy API going forward.

The short description:

Access to skb mark is removed, it is problematic when we add
features in the future because mark is a union and used by the
TCP/socket code internally. We don't want to expose this to the
BPF programs or let programs change the values.

The other change is caching metadata in the skb itself between
when the BPF program returns a redirect code and the core code
implements the redirect. This avoids having per cpu metadata.

Finally, tighten restriction on using sockmap to CAP_NET_ADMIN and
only SOCK_STREAM sockets.
====================
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Devmap is used with XDP which requires CAP_NET_ADMIN so lets also
make CAP_NET_ADMIN required to use the map.
Signed-off-by: NJohn Fastabend <john.fastabend@gmail.com>
Acked-by: NDaniel Borkmann <daniel@iogearbox.net>
Acked-by: NAlexei Starovoitov <ast@kernel.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Restrict sockmap to CAP_NET_ADMIN.
Signed-off-by: NJohn Fastabend <john.fastabend@gmail.com>
Acked-by: NDaniel Borkmann <daniel@iogearbox.net>
Acked-by: NAlexei Starovoitov <ast@kernel.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The skb->mark field is a union with reserved_tailroom which is used
in the TCP code paths from stream memory allocation. Allowing SK_SKB
programs to set this field creates a conflict with future code
optimizations, such as "gifting" the skb to the egress path instead
of creating a new skb and doing a memcpy.

Because we do not have a released version of SK_SKB yet lets just
remove it for now. A more appropriate scratch pad to use at the
socket layer is dev_scratch, but lets add that in future kernels
when needed.
Signed-off-by: NJohn Fastabend <john.fastabend@gmail.com>
Acked-by: NDaniel Borkmann <daniel@iogearbox.net>
Acked-by: NAlexei Starovoitov <ast@kernel.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

SK_SKB BPF programs are run from the socket/tcp context but early in
the stack before much of the TCP metadata is needed in tcp_skb_cb. So
we can use some unused fields to place BPF metadata needed for SK_SKB
programs when implementing the redirect function.

This allows us to drop the preempt disable logic. It does however
require an API change so sk_redirect_map() has been updated to
additionally provide ctx_ptr to skb. Note, we do however continue to
disable/enable preemption around actual BPF program running to account
for map updates.
Signed-off-by: NJohn Fastabend <john.fastabend@gmail.com>
Acked-by: NDaniel Borkmann <daniel@iogearbox.net>
Acked-by: NAlexei Starovoitov <ast@kernel.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Only TCP sockets have been tested and at the moment the state change
callback only handles TCP sockets. This adds a check to ensure that
sockets actually being added are TCP sockets.

For net-next we can consider UDP support.
Signed-off-by: NJohn Fastabend <john.fastabend@gmail.com>
Acked-by: NDaniel Borkmann <daniel@iogearbox.net>
Acked-by: NAlexei Starovoitov <ast@kernel.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Now sctp processes icmp redirect packet in sctp_icmp_redirect where
it calls sctp_transport_dst_check in which tp->dst can be released.

The problem is before calling sctp_transport_dst_check, it doesn't
check sock_owned_by_user, which means tp->dst could be freed while
a process is accessing it with owning the socket.

An use-after-free issue could be triggered by this.

This patch is to fix it by checking sock_owned_by_user before calling
sctp_transport_dst_check in sctp_icmp_redirect, so that it would not
release tp->dst if users still hold sock lock.

Besides, the same issue fixed in commit 45caeaa5 ("dccp/tcp: fix
routing redirect race") on sctp also needs this check.

Fixes: 55be7a9c ("ipv4: Add redirect support to all protocol icmp error handlers")
Reported-by: NEric Dumazet <edumazet@google.com>
Signed-off-by: NXin Long <lucien.xin@gmail.com>
Acked-by: NMarcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Acked-by: NNeil Horman <nhorman@tuxdriver.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Now when peeling off an association to the sock in another netns, all
transports in this assoc are not to be rehashed and keep use the old
key in hashtable.

As a transport uses sk->net as the hash key to insert into hashtable,
it would miss removing these transports from hashtable due to the new
netns when closing the sock and all transports are being freeed, then
later an use-after-free issue could be caused when looking up an asoc
and dereferencing those transports.

This is a very old issue since very beginning, ChunYu found it with
syzkaller fuzz testing with this series:

  socket$inet6_sctp()
  bind$inet6()
  sendto$inet6()
  unshare(0x40000000)
  getsockopt$inet_sctp6_SCTP_GET_ASSOC_ID_LIST()
  getsockopt$inet_sctp6_SCTP_SOCKOPT_PEELOFF()

This patch is to block this call when peeling one assoc off from one
netns to another one, so that the netns of all transport would not
go out-sync with the key in hashtable.

Note that this patch didn't fix it by rehashing transports, as it's
difficult to handle the situation when the tuple is already in use
in the new netns. Besides, no one would like to peel off one assoc
to another netns, considering ipaddrs, ifaces, etc. are usually
different.
Reported-by: NChunYu Wang <chunwang@redhat.com>
Signed-off-by: NXin Long <lucien.xin@gmail.com>
Acked-by: NMarcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Acked-by: NNeil Horman <nhorman@tuxdriver.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Daniel Borkmann says:

====================
bpf: Fix for BPF devmap percpu allocation splat

The set fixes a splat in devmap percpu allocation when we alloc
the flush bitmap. Patch 1 is a prerequisite for the fix in patch 2,
patch 1 is rather small, so if this could be routed via -net, for
example, with Tejun's Ack that would be good. Patch 3 gets rid of
remaining PCPU_MIN_UNIT_SIZE checks, which are percpu allocator
internals and should not be used.
====================
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

PCPU_MIN_UNIT_SIZE is an implementation detail of the percpu
allocator. Given we support __GFP_NOWARN now, lets just let
the allocation request fail naturally instead. The two call
sites from BPF mistakenly assumed __GFP_NOWARN would work, so
no changes needed to their actual __alloc_percpu_gfp() calls
which use the flag already.
Signed-off-by: NDaniel Borkmann <daniel@iogearbox.net>
Acked-by: NAlexei Starovoitov <ast@kernel.org>
Acked-by: NJohn Fastabend <john.fastabend@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

It was reported that syzkaller was able to trigger a splat on
devmap percpu allocation due to illegal/unsupported allocation
request size passed to __alloc_percpu():

  [   70.094249] illegal size (32776) or align (8) for percpu allocation
  [   70.094256] ------------[ cut here ]------------
  [   70.094259] WARNING: CPU: 3 PID: 3451 at mm/percpu.c:1365 pcpu_alloc+0x96/0x630
  [...]
  [   70.094325] Call Trace:
  [   70.094328]  __alloc_percpu_gfp+0x12/0x20
  [   70.094330]  dev_map_alloc+0x134/0x1e0
  [   70.094331]  SyS_bpf+0x9bc/0x1610
  [   70.094333]  ? selinux_task_setrlimit+0x5a/0x60
  [   70.094334]  ? security_task_setrlimit+0x43/0x60
  [   70.094336]  entry_SYSCALL_64_fastpath+0x1a/0xa5

This was due to too large max_entries for the map such that we
surpassed the upper limit of PCPU_MIN_UNIT_SIZE. It's fine to
fail naturally here, so switch to __alloc_percpu_gfp() and pass
__GFP_NOWARN instead.

Fixes: 11393cc9 ("xdp: Add batching support to redirect map")
Reported-by: NMark Rutland <mark.rutland@arm.com>
Reported-by: NShankara Pailoor <sp3485@columbia.edu>
Reported-by: NRichard Weinberger <richard@nod.at>
Signed-off-by: NDaniel Borkmann <daniel@iogearbox.net>
Cc: John Fastabend <john.fastabend@gmail.com>
Acked-by: NAlexei Starovoitov <ast@kernel.org>
Acked-by: NJohn Fastabend <john.fastabend@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add an option for pcpu_alloc() to support __GFP_NOWARN flag.
Currently, we always throw a warning when size or alignment
is unsupported (and also dump stack on failed allocation
requests). The warning itself is harmless since we return
NULL anyway for any failed request, which callers are
required to handle anyway. However, it becomes harmful when
panic_on_warn is set.

The rationale for the WARN() in pcpu_alloc() is that it can
be tracked when larger than supported allocation requests are
made such that allocations limits can be tweaked if warranted.
This makes sense for in-kernel users, however, there are users
of pcpu allocator where allocation size is derived from user
space requests, e.g. when creating BPF maps. In these cases,
the requests should fail gracefully without throwing a splat.

The current work-around was to check allocation size against
the upper limit of PCPU_MIN_UNIT_SIZE from call-sites for
bailing out prior to a call to pcpu_alloc() in order to
avoid throwing the WARN(). This is bad in multiple ways since
PCPU_MIN_UNIT_SIZE is an implementation detail, and having
the checks on call-sites only complicates the code for no
good reason. Thus, lets fix it generically by supporting the
__GFP_NOWARN flag that users can then use with calling the
__alloc_percpu_gfp() helper instead.
Signed-off-by: NDaniel Borkmann <daniel@iogearbox.net>
Cc: Tejun Heo <tj@kernel.org>
Cc: Mark Rutland <mark.rutland@arm.com>
Acked-by: NAlexei Starovoitov <ast@kernel.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Netanel Belgazal says:

====================
ENA ethernet driver bug fixes

Some fixes for ENA ethernet driver
====================
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

ethtool ena_get_channels() expose the max number of queues as the max
number of queues ENA supports (128 queues) and not the actual number
of created queues.
Signed-off-by: NNetanel Belgazal <netanel@amazon.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This failure is rare and only found on testing where deliberately fail
devm_ioremap()

[  451.170464] ena 0000:04:00.0: failed to remap regs bar
451.170549] Workqueue: pciehp-1 pciehp_power_thread
[  451.170551] task: ffff88085a5f2d00 task.stack: ffffc9000756c000
[  451.170552] RIP: 0010:devm_iounmap+0x2d/0x40
[  451.170553] RSP: 0018:ffffc9000756fac0 EFLAGS: 00010282
[  451.170554] RAX: 00000000fffffffe RBX: 0000000000000000 RCX:
0000000000000000
[  451.170555] RDX: ffffffff813a7e00 RSI: 0000000000000282 RDI:
0000000000000282
[  451.170556] RBP: ffffc9000756fac8 R08: 00000000fffffffe R09:
00000000000009b7
[  451.170557] R10: 0000000000000005 R11: 00000000000009b6 R12:
ffff880856c9d0a0
[  451.170558] R13: ffffc9000f5c90c0 R14: ffff880856c9d0a0 R15:
0000000000000028
[  451.170559] FS:  0000000000000000(0000) GS:ffff88085f400000(0000)
knlGS:0000000000000000
[  451.170560] CS:  0010 DS: 0000 ES: 0000 CR0: 0000000080050033
[  451.170561] CR2: 00007f169038b000 CR3: 0000000001c09000 CR4:
00000000003406f0
[  451.170562] DR0: 0000000000000000 DR1: 0000000000000000 DR2:
0000000000000000
[  451.170562] DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7:
0000000000000400
[  451.170563] Call Trace:
[  451.170572]  ena_release_bars.isra.48+0x34/0x60 [ena]
[  451.170574]  ena_probe+0x144/0xd90 [ena]
[  451.170579]  ? ida_simple_get+0x98/0x100
[  451.170585]  ? kernfs_next_descendant_post+0x40/0x50
[  451.170591]  local_pci_probe+0x45/0xa0
[  451.170592]  pci_device_probe+0x157/0x180
[  451.170599]  driver_probe_device+0x2a8/0x460
[  451.170600]  __device_attach_driver+0x7e/0xe0
[  451.170602]  ? driver_allows_async_probing+0x30/0x30
[  451.170603]  bus_for_each_drv+0x68/0xb0
[  451.170605]  __device_attach+0xdd/0x160
[  451.170607]  device_attach+0x10/0x20
[  451.170610]  pci_bus_add_device+0x4f/0xa0
[  451.170611]  pci_bus_add_devices+0x39/0x70
[  451.170613]  pciehp_configure_device+0x96/0x120
[  451.170614]  pciehp_enable_slot+0x1b3/0x290
[  451.170616]  pciehp_power_thread+0x3b/0xb0
[  451.170622]  process_one_work+0x149/0x360
[  451.170623]  worker_thread+0x4d/0x3c0
[  451.170626]  kthread+0x109/0x140
[  451.170627]  ? rescuer_thread+0x380/0x380
[  451.170628]  ? kthread_park+0x60/0x60
[  451.170632]  ret_from_fork+0x25/0x30
Signed-off-by: NNetanel Belgazal <netanel@amazon.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Decrease log level of checksum errors as these messages can be
triggered remotely by bad packets.
Signed-off-by: NNetanel Belgazal <netanel@amazon.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

If sending messages with no cable connected, it quickly happens that
there is no more TX context available. Then "gs_can_start_xmit()"
returns with "NETDEV_TX_BUSY" and the upper layer does retry
immediately keeping the CPU busy. To fix that issue, I moved
"atomic_dec(&dev->active_tx_urbs)" from "gs_usb_xmit_callback()" to
the TX done handling in "gs_usb_receive_bulk_callback()". Renaming
"active_tx_urbs" to "active_tx_contexts" and moving it into
"gs_[alloc|free]_tx_context()" would also make sense.
Signed-off-by: NWolfgang Grandegger <wg@grandegger.com>
Cc: linux-stable <stable@vger.kernel.org>
Signed-off-by: NMarc Kleine-Budde <mkl@pengutronix.de>

The dlc member of the struct rx_msg contains also the ESD_RTR flag to
mark received RTR frames. Without the fix the can_dlc value for received
RTR frames would always be set to 8 by get_can_dlc() instead of the
received value.

Fixes: 96d8e903 ("can: Add driver for esd CAN-USB/2 device")
Signed-off-by: NStefan Mätje <stefan.maetje@esd.eu>
Cc: linux-stable <stable@vger.kernel.org>
Signed-off-by: NMarc Kleine-Budde <mkl@pengutronix.de>

This patch adds the missing check and error handling for out-of-memory
situations, when kzalloc cannot allocate memory.

Fixes: cb5635a3 ("can: complete initial namespace support")
Acked-by: NOliver Hartkopp <socketcan@hartkopp.net>
Cc: linux-stable <stable@vger.kernel.org>
Signed-off-by: NMarc Kleine-Budde <mkl@pengutronix.de>

"proto_tab" is a RCU protected array, when directly accessing the array,
sparse throws these warnings:

  CHECK   /srv/work/frogger/socketcan/linux/net/can/af_can.c
net/can/af_can.c:115:14: error: incompatible types in comparison expression (different address spaces)
net/can/af_can.c:795:17: error: incompatible types in comparison expression (different address spaces)
net/can/af_can.c:816:9: error: incompatible types in comparison expression (different address spaces)

This patch fixes the problem by using rcu_access_pointer() and
annotating "proto_tab" array as __rcu.
Signed-off-by: NMarc Kleine-Budde <mkl@pengutronix.de>