In RS485 mode, we may want to set the delay_rts_after_send value to 0.
In the datasheet, the 0 value is said to "disable" the Transmitter Timeguard but
this is exactly the expected behavior if we want no delay...

Moreover, if the value was set to non-zero value by device-tree or earlier
ioctl command, it was impossible to change it back to zero.
Reported-by: NSami Pietikäinen <Sami.Pietikainen@wapice.com>
Signed-off-by: NNicolas Ferre <nicolas.ferre@atmel.com>
Cc: stable@vger.kernel.org  # 3.2+
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

In commit 02730d3c
(Merge 4.1-rc4 into tty-next), git mismerged some lines,
reintroducing a reference to the removed field
uart_amba_port.tx_irq_seen.  This causes a build failure.

This patch removes the mismerged lines, restoring the code to what
was in tty-next (which was the intention).
Signed-off-by: NDave Martin <Dave.Martin@arm.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

This code is no longer used now that mach-msm has been removed.
Delete it.

Cc: David Brown <davidb@codeaurora.org>
Cc: Bryan Huntsman <bryanh@codeaurora.org>
Cc: Daniel Walker <dwalker@fifo99.com>
Signed-off-by: NStephen Boyd <sboyd@codeaurora.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Function tegra_uart_dma_channel_allocate() does not check that
dma_map_single() mapped the DMA buffer correctly. Add a check for this
and appropriate error handling.

Furthermore, if dmaengine_slave_config() (called by
tegra_uart_dma_channel_allocate()) fails, then memory allocated/mapped
is not freed/unmapped. Therefore, call tegra_uart_dma_channel_free()
instead of just dma_release_channel() if  dmaengine_slave_config() fails.
Signed-off-by: NJon Hunter <jonathanh@nvidia.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

There are two issues in the shutdown path of the UARTs which are:
1. The function tegra_uart_shutdown() calls tegra_uart_flush_buffer()
   to stop DMA TX transfers. However, tegra_uart_flush_buffer() is
   called after the DMA channels have already been freed and so actually
   does nothing.
2. The function that frees the DMA channels
   (tegra_uart_dma_channel_free()), unmaps the dma buffer before
   freeing the DMA channel and does not ensure the DMA has been
   stopped.

Resolve this by fixing the code in tegra_uart_dma_channel_free() to
ensure the DMA is stopped, free the DMA channel and then unmap the DMA
buffer. Finally, remove the unnecessary call to tegra_uart_flush_buffer().
Signed-off-by: NJon Hunter <jonathanh@nvidia.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

The DMA cookie for the RX channel is being used by the TX channel.
Therefore, fix driver to use the correct DMA cookie for the TX channel.
Signed-off-by: NJon Hunter <jonathanh@nvidia.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

The function tty_insert_flip_string() takes an argument "size" which is
of type size_t. This is an unsigned type. Update the count,
rx_bytes_requested and tx_bytes_requested in the tegra serial driver to
be unsigned integers so that an unsigned type is passed to
tty_insert_flip_string().
Signed-off-by: NJon Hunter <jonathanh@nvidia.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

The tegra serial driver has two paths through which receive data is
copied up to the tty layer. These are:
1. DMA completion callback
2. UART RX interrupt

A UART RX interrupt occurs for either RX_TIMEOUT (data has been sitting
in the Rx FIFO for more than 4 character times without being read
because there is not enough data to reach the trigger level), End of
Receive Data event (receiver detects that data stops coming in for more
than 4 character times) or a receive error.

In the RX interrupt path, the following happens ...
- All RX DMA transfers are stopped
- Any data in the DMA buffer and RX FIFO are copied up to the tty layer.
- DMA is restarted/primed for the RX path

In the DMA completion callback, the DMA buffer is copied up to the tty
layer but there is no check to see if the RX interrupt could have
occurred between the DMA interrupt firing the the DMA callback running.
Hence, if a RX interrupt was to occur shortly after the DMA completion
interrupt, it is possible that the RX interrupt path has already copied
the DMA buffer before the DMA callback has been called. Therefore, when
the DMA callback is called, if the DMA is already in-progress, then this
indicates that the UART RX interrupt has already occurred and there is
nothing to do in the DMA callback. This race condition can cause
duplicated data to be received.
Signed-off-by: NShardar Shariff Md <smohammed@nvidia.com>
[jonathanh@nvidia.com: Moved async_tx_ack() call to after check to see
 if DMA has completed because if the DMA is in progress we do not need
 to ACK yet. Changed the print from dev_info to dev_debug. Updated
 changelog to add more commentary on the race condition based upon
 feedback from author.]
Signed-off-by: NJon Hunter <jonathanh@nvidia.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

It is only necessary to read data from the dma buffer when the count
value is non-zero and hence, tegra_uart_copy_rx_to_tty() so only be
called when this is the case.

Although, this was being tested for in two places, there is a third
place where this was not tested. However, instead of adding another
if-statement prior to calling tegra_uart_copy_rx_to_tty(), move the test
inside the function.
Signed-off-by: NShardar Shariff Md <smohammed@nvidia.com>
[jonathanh@nvidia.com: Re-worked patch to move the check for the count
 value inside the function tegra_uart_copy_rx_to_tty(). Updated
 changelog with more commentary.]
Signed-off-by: NJon Hunter <jonathanh@nvidia.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

For all tegra devices (up to t210), there is a hardware issue that
requires software to wait for 3 UART clock periods after enabling
the TX fifo, otherwise data could be lost.
Signed-off-by: NJon Hunter <jonathanh@nvidia.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

For all tegra devices (up to t210), there is a hardware issue that
requires software to wait for 32 UART clock periods for the flush
to propagate otherwise TX data could be post. Add a helper function
to wait for N UART clock periods and update delay following FIFO
flush to be 32 UART clock cycles.
Signed-off-by: NJon Hunter <jonathanh@nvidia.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

The port.type has already been set by of_platform_serial_setup()
called from a few lines above.
Setting it to the same value is redundant.
Signed-off-by: NMasahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

The port.fifosize member has already been copied at 8 lines above.
Maybe the compiler optimization can clean it away, but just in case.
Signed-off-by: NMasahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: NPeter Hurley <peter@hurleysoftware.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Early console functions are only used during the early boot stage.
This change just saves a small amount of memory footprint.
Signed-off-by: NMasahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

When nr_uarts was set to 0 (via config or 8250_core.nr_uarts), we crash
early on x86 because serial8250_isa_init_ports dereferences base_ops
which remains NULL. In fact, there is nothing to do for all the callers
of serial8250_isa_init_ports if there are no uarts.

Based on suggestions by Peter Hurley.
Signed-off-by: NJan Kiszka <jan.kiszka@siemens.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

The platform_device_id is not modified by the driver and core uses it as
const.
Signed-off-by: NKrzysztof Kozlowski <k.kozlowski.k@gmail.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Staticize symbols not exported and not used outside of file.
Signed-off-by: NKrzysztof Kozlowski <k.kozlowski.k@gmail.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

The platform_device_id is not modified by the driver and core uses it as
const.
Signed-off-by: NKrzysztof Kozlowski <k.kozlowski.k@gmail.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

The platform_device_id is not modified by the driver and core uses it as
const.
Signed-off-by: NKrzysztof Kozlowski <k.kozlowski.k@gmail.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

The code it refers to was removed in commit b545e4f4 ("serial:
sh-sci: Compute overrun_bit without using baud rate algo").
Signed-off-by: NGeert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

error_mask is the union of all error indicating bits in the SCxSR
register, while overrun_mask may apply to a different register (SCLSR),
depending on the SCI variant.

Hence overrun_mask should only be ORed into error_mask if it applies to
the SCxSR register.
Signed-off-by: NGeert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

The various SCI implementations use 3 different methods to signal
overrun errors:
  - Bit SCI_ORER in register SCxSR on SCI,
  - Bit SCIFA_ORER in register SCxSR on SCIFA and SCIFB, and SCIF on
    SH7705/SH7720/SH7721,
  - Bit SCLSR_ORER in (optional!) register SCLSR on (H)SCIF.

However:
  1. sci_handle_fifo_overrun()
       a. handles (H)SCIF and SCIFA/SCIFB only,
       b. treats SCIF on SH7705/SH7720/SH7721 incorrectly,
  2. sci_mpxed_interrupt()
       a. treats SCIF on SH7705/SH7720/SH7721 incorrectly,
       b. ignores that not all SCIFs have the SCLSR register, causing
	  "Invalid register access" WARN()ings.

To fix the above:
  1. Determine and store the correct register enum during
     initialization,
  2. Replace the duplicated buggy switch statements by using the stored
     register enum,
  3. Add the missing existence check to  sci_mpxed_interrupt().
Signed-off-by: NGeert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Add the missing overrun bit definition for (H)SCIF.
Replace overrun_bit by overrun_mask, so we can use the existing
defines instead of hardcoded values.
Signed-off-by: NGeert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Add the missing overrun error bit in SCxSR on SCIFA/SCIFB and SCIF on
SH7705/SH7720/SH7721.
Document what the corresponding bit(s) on plain SCIF are used for.
Sort the components of SCIF_DEFAULT_ERROR_MASK by reverse definition
order.

Replace the hardcoded values in the SCxSR_*_CLEAR macros by proper
defines. Use bit masks (negations of sets of bits) to make it more
obvious which bits are being cleared.

Assembler output (on sh) was compared before and after this commit:
  - For the first branch of the big "#if defined(...) || ..." construct,
    the code has changed slightly, as 32-bit bitmasks can be loaded in a
    single instruction, unlike the old large 16-bit constants (the SCxSR
    register is 16 bit, so we don't care about the top 16 bits),
  - For the second branch, the generated code is identical.
Signed-off-by: NGeert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Signed-off-by: NGeert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Signed-off-by: NGeert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Add the register definitions for the Serial Port Control and Data
Registers on SCIFA/SCIFB, which are needed for RTS/CTS pin control.

Extracted from patches by Magnus Damm <damm+renesas@opensource.se>.
Signed-off-by: NGeert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Add the missing register bit definitions to set the RTS pin and read the
CTS pin on (H)SCIF.

Extracted from patches by Magnus Damm <damm+renesas@opensource.se>.
Signed-off-by: NGeert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Move private register definitions and enums from the public
<linux/serial_sci.h> header file to the driver private "sh-sci.h" header
file.

The common Serial Control Register definitions are left in the public
header file, as they're needed to fill in plat_sci_port.scscr on legacy
systems not using DT.
Signed-off-by: NGeert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

We should not be doing assignments within an if () block
so fix up the code to not do this.

change was created using Coccinelle.

CC: Jiri Slaby <jslaby@suse.cz>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

We should not be doing assignments within an if () block
so fix up the code to not do this.

change was created using Coccinelle.

CC: Pat Gefre <pfg@sgi.com>
CC: Jiri Slaby <jslaby@suse.cz>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

We should not be doing assignments within an if () block
so fix up the code to not do this.

change was created using Coccinelle.

CC: Pat Gefre <pfg@sgi.com>
CC: Jiri Slaby <jslaby@suse.cz>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

We should not be doing assignments within an if () block
so fix up the code to not do this.

change was created using Coccinelle.

CC: Jiri Slaby <jslaby@suse.cz>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

We should not be doing assignments within an if () block
so fix up the code to not do this.

change was created using Coccinelle.

CC: Mikael Starvik <starvik@axis.com>
CC: Jiri Slaby <jslaby@suse.cz>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>
Acked-by: NJesper Nilsson <jesper.nilsson@axis.com>

We should not be doing assignments within an if () block
so fix up the code to not do this.

change was created using Coccinelle.

CC: Jiri Slaby <jslaby@suse.cz>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

In SiRF platform, there are different fifo size of uart and usp,
with the fifosize configuration changes in different chips, we
can not use port line to decide how to check FIFO full,empty and
level.

There is a direct mapping between FIFO HW register layout with
fifo size, so move to use fifosize as the input to check fifo
status.
Signed-off-by: NQipan Li <Qipan.Li@csr.com>
Signed-off-by: NBarry Song <Baohua.Song@csr.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

In different platform of SiRF SoCs, there is no same uart and usp-uart
numbers, it is not convenient to use hard-coded ports array and port
lines.

here we drop the hard-coded ports table , and drop "cell-index". then
move to use alias id to get line.

for example:
	aliases {
		serial0 = &uart0;
		serial1 = &uart1;
		serial2 = &uart2;
		serial3 = &uart3;
		serial4 = &uart4;
		serial5 = &uart5;
		serial6 = &uart6;
		serial9 = &usp2;
	};

at the same, enlarge the max port number according to the chip with the most
UART.
Signed-off-by: NQipan Li <Qipan.Li@csr.com>
Signed-off-by: NBarry Song <Baohua.Song@csr.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Add 8250 MTK UART driver to support earlycon device tree.
Earlycon take effect by
  add "earlycon" in kernel boot argument
  add "linux,sdtout-path" property in device tree file
Signed-off-by: NEddie Huang <eddie.huang@mediatek.com>
Tested-by: NSascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

8250-like uart driver may call early_serial8250_setup to
reuse 8250_early.c character output function.
Signed-off-by: NEddie Huang <eddie.huang@mediatek.com>
Tested-by: NSascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

This reverts commit f2ee6dfa.

Jakub Kiciński observed that this patch can cause the pl011
driver to hang if if the only process with a pl011 port open is
killed by a signal, pl011_shutdown() can get called with an
arbitrary amount of data still in the FIFO.

Calling _shutdown() with the TX FIFO non-empty is questionable
behaviour and my itself be a bug.

Since the affected patch was speculative anyway, and brings limited
benefit, the simplest course is to remove the assumption that TXIS
will always be left asserted after the port is shut down.
Signed-off-by: NDave Martin <Dave.Martin@arm.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>