As the kernel has no way to know whether a key was released
while the system was asleep, keys need to be reported released
as the system is resumed, lest autorepeat set in.
Signed-off-by: NOliver Neukum <oneukum@suse.de>
Signed-off-by: NDmitry Torokhov <dtor@mail.ru>

ADS7845 is a controller for 5-wire touch screens and somewhat
different from 7846. It requires three serial communications to
accomplish one complete conversion. Unlike 7846 it doesn't allow
Z1-/Z2- position measurement.

The patch extends the ads7846 driver to also support ads7845.
The packet struct is extended to contain needed command and
conversion buffers. ads7846_rx() and ads7846_rx_val() now
differentiate between 7845 and 7846 case. ads7846_probe() is
modified to setup ads7845 specific command and conversion
messages and to switch ads7845 into power-down mode, since
this is needed to be prepared to respond to pendown interrupts.
Signed-off-by: NAnatolij Gustschin <agust@denx.de>
Signed-off-by: NDmitry Torokhov <dtor@mail.ru>

Tested-by: NAnatolij Gustschin <agust@denx.de>
Signed-off-by: NDmitry Torokhov <dtor@mail.ru>

Suspending and resuming the device should be separate from enabling
and disabling it through sysfs attribute and thus should not alter
ac->disabled flag.

[michael.hennerich@analog.com: various fixups]
Tested-by: NMichael Hennerich <michael.hennerich@analog.com>
Signed-off-by: NDmitry Torokhov <dtor@mail.ru>

Some input events users such as Android require BTN_TOUCH events.
Implement EV_KEY/BTN_TOUCH and make sure that the release event
is not erroneous scheduled without a preceding valid touch.
Avoid duplicated BTN_TOUCH events, even though input core filters
them.
Signed-off-by: NMichael Hennerich <michael.hennerich@analog.com>
Signed-off-by: NDmitry Torokhov <dtor@mail.ru>

Signed-off-by: NMichael Hennerich <michael.hennerich@analog.com>
Signed-off-by: NDmitry Torokhov <dtor@mail.ru>

Avoid additional addressing overhead incurred by word_data transfers.
Signed-off-by: NMichael Hennerich <michael.hennerich@analog.com>
Signed-off-by: NMike Frysinger <vapier@gentoo.org>
Signed-off-by: NDmitry Torokhov <dtor@mail.ru>

Tested-by: NMichael Hennerich <michael.hennerich@analog.com>
Signed-off-by: NDmitry Torokhov <dtor@mail.ru>

The ad7879 driver is using the old bus method of only supporting one
at a time (I2C or SPI). So refactor it like the other input drivers
that support multiple busses simultaneously.
Signed-off-by: NMike Frysinger <vapier@gentoo.org>
Signed-off-by: NMichael Hennerich <michael.hennerich@analog.com>
Signed-off-by: NDmitry Torokhov <dtor@mail.ru>

Tested-by: NMichael Hennerich <michael.hennerich@analog.com>
Signed-off-by: NDmitry Torokhov <dtor@mail.ru>

We reuse the "i" variable later on so if we goto fail3 or fail4
then "i" will be set to the wrong thing and cause a crash.
Signed-off-by: NDan Carpenter <error27@gmail.com>
Signed-off-by: NDmitry Torokhov <dtor@mail.ru>

gpiolib now has debounce support added in .35, so let's make use of it.
This allows to use hardware GPIO debouncing on some platforms like OMAP.

In case gpiolib debounce setup fails for some GPIO, the driver will fall
back to timer based debouncing, which is what it used before.
Signed-off-by: NGrazvydas Ignotas <notasas@gmail.com>
Signed-off-by: NDmitry Torokhov <dtor@mail.ru>

This patch adds support for the ET&T TC4UM 4-wire USB touchscreen
controller and tries to reuse the bits for TC5UH controller in kernel
already. Data interface is same.
Tested-by: NRoger Pueyo Centelles <rogerpueyo@rogerpueyo.com>
Signed-off-by: NPetr Štetiar <ynezz@true.cz>
Signed-off-by: NDmitry Torokhov <dtor@mail.ru>

On some platforms, for example with GPIO interrupts on mpc5121,
it is not possible to configure falling edge interrupts.

Specifying irq trigger type in platform data structure
allows using ads7846 driver on such platforms.
Signed-off-by: NAnatolij Gustschin <agust@denx.de>
Signed-off-by: NDmitry Torokhov <dtor@mail.ru>

Add support for the two new devices: DTU2231 and DTU1631.
Signed-off-by: NPing Cheng <pingc@wacom.com>
Signed-off-by: NDmitry Torokhov <dtor@mail.ru>

select_keymap() calls copy_keymap() to allocate a memory for keymap.
This patch adds a missing kfree(keymap) in wb_module_init error path.
Signed-off-by: NAxel Lin <axel.lin@gmail.com>
Signed-off-by: NDmitry Torokhov <dtor@mail.ru>

Signed-off-by: NMichael Hennerich <michael.hennerich@analog.com>
Signed-off-by: NMike Frysinger <vapier@gentoo.org>
Signed-off-by: NDmitry Torokhov <dtor@mail.ru>

This is a driver for the ADXL345/346 Three-Axis Digital Accelerometers.
Signed-off-by: NMichael Hennerich <michael.hennerich@analog.com>
Signed-off-by: NChris Verges <chrisv@cyberswitching.com>
Signed-off-by: NLuotao Fu <l.fu@pengutronix.de>
Signed-off-by: NBarry Song <barry.song@analog.com>
Signed-off-by: NMike Frysinger <vapier@gentoo.org>
Signed-off-by: NDmitry Torokhov <dtor@mail.ru>

A column or row configured as a GPI can be programmed to be part
of the key event table and therefore also capable of generating a
key event interrupt. A key event interrupt caused by a GPI follows
the same process flow as a key event interrupt caused by a key
press. GPIs configured as part of the key event table allow single
key switches and other GPI interrupts to be monitored. As part of
the event table, GPIs are represented by the decimal value 97 (0x61
or 1100001) through the decimal value 114 (0x72 or 1110010). See
table below for GPI event number assignments for rows and columns.

GPI Event Number Assignments for Rows
Row0 Row1 Row2 Row3 Row4 Row5 Row6 Row7
97   98   99   100  101  102  103  104

GPI Event Number Assignments for Cols
Col0 Col1 Col2 Col3 Col4 Col5 Col6 Col7 Col8 Col9
105  106  107  108  109  110  111  112  113  114
Signed-off-by: NXiaolong Chen <xiao-long.chen@motorola.com>
Signed-off-by: NYuanbo Ye <yuan-bo.ye@motorola.com>
Signed-off-by: NTao Hu <taohu@motorola.com>
Acked-by: NMichael Hennerich <michael.hennerich@analog.com>
Signed-off-by: NDmitry Torokhov <dtor@mail.ru>

When the client buffer is very small and wraps around a lot, it may
well be that a write increases the head such that head == tail. If
this happens between the point where a poll is triggered and the
actual data is being read, there will be no data to read. This is
confusing to applications, which might end up closing the file.

This patch solves the problem by making sure the client buffer is
never empty after writing to it.
Signed-off-by: NHenrik Rydberg <rydberg@euromail.se>
Signed-off-by: NDmitry Torokhov <dtor@mail.ru>

The MT devices produce a lot of data. Tell the underlying input device
approximately how many events will be sent per synchronization, to allow
for better buffering. The number is a template based on continuously
reporting details for each finger on a single hand.
Signed-off-by: NHenrik Rydberg <rydberg@euromail.se>
Signed-off-by: NDmitry Torokhov <dtor@mail.ru>

Some devices, in particular MT devices, produce a lot of data.  This
may lead to overflowing of the event queues in evdev driver, which
by default are fairly small. Let the drivers hint the average number
of events per packet generated by the device, and use that information
when computing the buffer size evdev should use for the device.
Signed-off-by: NHenrik Rydberg <rydberg@euromail.se>
Acked-by: NChase Douglas <chase.douglas@canonical.com>
Signed-off-by: NDmitry Torokhov <dtor@mail.ru>

Allocate the event buffer dynamically, and prepare to compute the
buffer size in a separate function. This patch defines the size
computation to be identical to the current code, and does not contain
any logical changes.
Signed-off-by: NHenrik Rydberg <rydberg@euromail.se>
Signed-off-by: NDmitry Torokhov <dtor@mail.ru>

Stanse found that tsc is dereferenced earlier than checked for being
NULL in tps6507x_ts_remove. Remove the test because there is no way
for tsc to be NULL there.
Signed-off-by: NJiri Slaby <jslaby@suse.cz>
Signed-off-by: NDmitry Torokhov <dtor@mail.ru>

This one adds support of a combined irq source for the whole matrix keypad.
This can be useful if all rows and columns of the keypad are e.g. connected
to a GPIO expander, which only has one interrupt line for all events on
every single GPIO.
Signed-off-by: NLuotao Fu <l.fu@pengutronix.de>
Acked-by: NEric Miao <eric.y.miao@gmail.com>
Signed-off-by: NDmitry Torokhov <dtor@mail.ru>

Commit 55929332 "drivers: Push down BKL into various drivers"
introduced a regression in hp_sdc_rtc, caused by a missing
change of the .unlocked_ioctl pointer to the newly introduced
function.

Fixes:

	drivers/input/misc/hp_sdc_rtc.c:681: warning: initialization from
	incompatible pointer type
	drivers/input/misc/hp_sdc_rtc.c:665: warning:
	‘hp_sdc_rtc_unlocked_ioctl’ defined but not used
Reported-by: NGeert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: NArnd Bergmann <arnd@arndb.de>
Acked-by: NGeert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: NFrederic Weisbecker <fweisbec@gmail.com>

If we fail to submit URBs we should take touchpad out of wellsping
mode.
Signed-off-by: NLuo Jinghua <sunmoon1997@gmail.com>
Signed-off-by: NDmitry Torokhov <dtor@mail.ru>

Let's perform be16_to_cpu() conversions once for each received packet,
and then use cached values. Makes code a little bit easier to follow.
Tested-by: NOndrej Zary <linux@rainbow-software.org>
Signed-off-by: NDmitry Torokhov <dtor@mail.ru>

CONFIG_SPRUCE was removed from kernel around 2.6.26; let's remove the
last remaining piece.
Signed-off-by: NChristoph Egger <siccegge@cs.fau.de>
Signed-off-by: NDmitry Torokhov <dtor@mail.ru>

Signed-off-by: NPing Cheng <pingc@wacom.com>
Signed-off-by: NDmitry Torokhov <dtor@mail.ru>

I2C drivers can use the clientdata-pointer to point to private data. As I2C
devices are not really unregistered, but merely detached from their driver, it
used to be the drivers obligation to clear this pointer during remove() or a
failed probe(). As a couple of drivers forgot to do this, it was agreed that it
was cleaner if the i2c-core does this clearance when appropriate, as there is
no guarantee for the lifetime of the clientdata-pointer after remove() anyhow.
This feature was added to the core with commit
e4a7b9b0 to fix the faulty drivers.

As there is no need anymore to clear the clientdata-pointer, remove all current
occurrences in the drivers to simplify the code and prevent confusion.
Signed-off-by: NWolfram Sang <w.sang@pengutronix.de>
Acked-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: NGreg Kroah-Hartman <gregkh@suse.de>
Acked-by: NRichard Purdie <rpurdie@linux.intel.com>
Acked-by: NDmitry Torokhov <dtor@mail.ru>
Signed-off-by: NJean Delvare <khali@linux-fr.org>

This patch fixes the follwing warning introduced by commit
067fb2f6 ("Input: ads7846 - return error on
regulator_get() failure"):

drivers/input/touchscreen/ads7846.c: In function 'ads7846_probe':
drivers/input/touchscreen/ads7846.c:1167: warning: format '%ld' expects
type 'long int', but argument 4 has type 'int'
Signed-off-by: NDmitry Torokhov <dtor@mail.ru>

1) Use msecs_to_jiffies() instead of calculating by hand.
2) Call cancel_delayed_work_sync() instead of cancel_delayed_work()
   followed by a separate flush_workqueue().
3) Remove the "tsc->wq = 0;"  Sparse complains about that because
   tsc->wq is a pointer, not an int.  It's not needed because we just
   free the pointer anyway.
Signed-off-by: NDan Carpenter <error27@gmail.com>
Signed-off-by: NDmitry Torokhov <dtor@mail.ru>

The S3C touchscreen driver is logging at LOG_INFO on every stylus up
event which spams the console needlessly.  Reduce the priority of the
message to debug level for some peace and quiet.
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: NDmitry Torokhov <dtor@mail.ru>

The name of the Kconfig symbol for the ADC has changed as a result of
application to more SoCs but the select statement has not been updated,
causing linker failures as the ADC core has not been built.
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: NDmitry Torokhov <dtor@mail.ru>

Add touch screen input driver for TPS6507x family of multi-function
chips.  Uses the TPS6507x MFD driver.  No interrupt support due to
testing limitations of current hardware.
Signed-off-by: NTodd Fischer <todd.fischer@ridgerun.com>
Signed-off-by: NSamuel Ortiz <sameo@linux.intel.com>

Without s3c24xx ids driver doesn't attach on s3c2410 and s3c244x
Signed-off-by: NVasily Khoruzhick <anarsoul@gmail.com>
Acked-by: NBen Dooks <ben-linux@fluff.org>
Signed-off-by: NDmitry Torokhov <dtor@mail.ru>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Bigger Nexio touchscreens not only send more data but also the header
values are modified somewhat.  Fix the header (it's a guesswork but
it works at least on one 46" touchscreen with 2.00SMS firmware) and
also increase rept_size.
Signed-off-by: NOndrej Zary <linux@rainbow-software.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NDmitry Torokhov <dtor@mail.ru>

In probe(), if regulator_get() failed, an error code was not being
returned causing the driver to be successfully bound, even though
probe failed.  This in turn caused the suspend, resume and remove
methods to be registered and accessed via the SPI core.  Since these
functions all access private driver data using pointers that had been
freed during the failed probe, this would lead to unpredictable
behavior.

This patch ensures that probe() returns an error code in this failure
case so the driver is not bound.

Found using lockdep and noticing the lock used in the suspend/resum
path pointed to a bogus lock due to the freed memory.
Signed-off-by: NKevin Hilman <khilman@deeprootsystems.com>
Acked-by: NMike Frysinger <vapier@gentoo.org>
Signed-off-by: NDmitry Torokhov <dtor@mail.ru>

Signed-off-by: NGeert Uytterhoeven <geert@linux-m68k.org>