The values in the advertising field are typically ADVERTISED_xxx, not
SUPPORTED_xxx.  Both SUPPORTED_10000baseT_Full and
ADVERTISED_1000baseT_Full have the same value.

The semantic match that finds this problem is as follows:
(http://www.emn.fr/x-info/coccinelle/)

// <smpl>
@@
struct ethtool_cmd E;
@@
*E.advertising = SUPPORTED_10000baseT_Full
// </smpl>
Signed-off-by: NJulia Lawall <julia@diku.dk>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The interrupt moderation should not depend on number of incoming
bytes, but on number of incoming packets.
The previous scheme caused very high interrupts rate for small
messages when big MTU was configured.
Signed-off-by: NYevgeny Petrilin <yevgenyp@mellanox.co.il>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NYevgeny Petrilin <yevgenyp@mellanox.co.il>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

en_params.c file now only handles Ethtool functionality
Signed-off-by: NYevgeny Petrilin <yevgenyp@mellanox.co.il>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

For each debug message, the message will show interface name in case
that the net device was registered, and PCI bus ID with port number
if we were not registered yet. Messages that are not port/netdev specific
stayed in the old format
Signed-off-by: NYevgeny Petrilin <yevgenyp@mellanox.co.il>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NYevgeny Petrilin <yevgenyp@mellanox.co.il>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Now using Ethtool to determine ring sizes, removed the module parameters
that controlled those values.
Modifying ring size requires restart of the interface.
Signed-off-by: NYevgeny Petrilin <yevgenyp@mellanox.co.il>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Removed module parameter specifying number of RX rings
Signed-off-by: NYevgeny Petrilin <yevgenyp@mellanox.co.il>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

They are controlled through Ethtool interface.
Signed-off-by: NYevgeny Petrilin <yevgenyp@mellanox.co.il>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

They are controlled through Ethtool interface, no need to have two
ways to modify them.
Signed-off-by: NYevgeny Petrilin <yevgenyp@mellanox.co.il>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Before the change the driver reported the same pause parameters
for all the ports, even only one of them was modified.
Signed-off-by: NYevgeny Petrilin <yevgenyp@mellanox.co.il>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The Mellanox ConnectX can operate as an InfiniBand adapter, as an
Ethernet NIC, or as a Fibre Channel (FC) HBA.  The kernel has a
low-level driver, mlx4_core, which handles multiplexing access to the
device, and there is also already an InfiniBad driver, mlx4_ib.

This patch adds a new driver, mlx4_en, which implements a standard
Ethernet NIC driver.
Signed-off-by: NLiran Liss <liranl@mellanox.co.il>
Signed-off-by: NYevgeny Petrilin <yevgenyp@mellanox.co.il>
Signed-off-by: NRoland Dreier <rolandd@cisco.com>