The check doesn't make much sense. If the address
were to be 0x0000 the check would fail. In this
case a 0 address isn't wrong.
Signed-off-by: NMichal Kazior <michal.kazior@tieto.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

What the function does is to actually wait for the
firmware indication bit to be set. Prerequisite
for this is having interrupts registered.
Signed-off-by: NMichal Kazior <michal.kazior@tieto.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

The function will soon be called from more than 1
place.
Signed-off-by: NMichal Kazior <michal.kazior@tieto.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

It was possible for FW error tasklet to be
executed during teardown. This could lead to
system crashes and/or memory corruption.
Signed-off-by: NMichal Kazior <michal.kazior@tieto.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

It wasn't really useful to have it to begin with.
This makes it a little simpler to re-arrange PCI
init code as some function depended on
ar_pci->ce_count being set.
Signed-off-by: NMichal Kazior <michal.kazior@tieto.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

memory is malloced in ath10k_pci_probe() and should be freed before
leaving from the error handling cases, otherwise it will cause
memory leak.
Signed-off-by: NWei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

ath10k_pci_wait() didn't notify any errors to callers, it
just printed a warning so add proper error handling. This fixes
a crash Ben reported:

ath10k: MSI-X interrupt handling (8 intrs)
ath10k: Unable to wakeup target
ath10k: target took longer 5000 us to wake up (awake count 1)
ath10k: Failed to get pcie state addr: -16
ath10k: early firmware event indicated
BUG: unable to handle kernel NULL pointer dereference at 0000000000000004
IP: [<ffffffffa06ae46c>] ath10k_ce_completed_send_next+0x47/0x122 [ath10k_pci]
Reported-by: NBen Greear <greearb@candelatech.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

To make it easier to access SOC registers. No functional
changes.
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

If firmware crashes during FW probing it would try
to perform FW recovery which uses mac80211
workqueue before registering to mac80211.

Using internal workqueue solves the problem.
Signed-off-by: NMichal Kazior <michal.kazior@tieto.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

The value provided by num_sends_allowed is now
derived from CE source ringbuffer state.
Signed-off-by: NMichal Kazior <michal.kazior@tieto.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

It is completely pointless to keep this function
around. It doesn't do anything different than
ce_send except it introduces more overhead.
Signed-off-by: NMichal Kazior <michal.kazior@tieto.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

The driver core clears the driver data to NULL after device_release
or on probe failure. Thus, it is not needed to manually clear the
device driver data to NULL.
Signed-off-by: NJingoo Han <jg1.han@samsung.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Commit e9bb0aa3 ("ath10k: delete struct ce_sendlist") broke
num_sends_allowed incrementing. num_sends_allowed
exceeded initial values and could overflow.

This code was supposed to replenish
num_sends_allowed for partial sendlist items (i.e.
before final sendlist item from a sendlist was
completed and could be processed by completion
handlers).

Fortunately it seems it did not cause any major breakage,
yet.
Signed-off-by: NMichal Kazior <michal.kazior@tieto.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

The driver core clears the driver data to NULL after device_release
or on probe failure. Thus, it is not needed to manually clear the
device driver data to NULL.
Signed-off-by: NJingoo Han <jg1.han@samsung.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

struct ce_sendlist is useless as we always add just one buffer onto it.
And most importantly, it's ugly as it doesn't use skb properly.
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

To unify all boot related debug messages into one debug
level.
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

The double while() could end up running forever.
Inner while() would complete very fast. However
the completion processing could take enough time
for more completions to flow in. In that case the
outer while() would not terminate and run again,
and again. This could happen especially on a slow
host system.

This could lead to a system freeze during heavy
traffic. Note: this doesn't solve all known
starvation issues yet.
Signed-off-by: NMichal Kazior <michal.kazior@tieto.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

The indentation here implies this was meant to be
a multi-statement if, but it lacks the braces.

kvalo: add "ath10k: " prefix
Signed-off-by: NDave Jones <davej@fedoraproject.org>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

ath10k doesn't support qca988x hw1.0 boards anymore. Unfortunately
the PCI id is the same in hw1.0 and hw2.0 so ath10k tries to use
hw1.0 boards anyway. But without hw1.0 workarounds in place
ath10k just crashes horribly.

To avoid using hw1.0 boards at all add a chip id detection
and fail the probe if hw1.0 is detected:

[ 5265.786408] ath10k: ERROR: qca988x hw1.0 is not supported
[ 5265.786497] ath10k: Unsupported chip id 0x043200ff
[ 5265.786574] ath10k: could not register driver core (-95)
[ 5265.793191] ath10k_pci: probe of 0000:02:00.0 failed with error -95

Also add a warning if there's an unknown chip id but continue
the boot process normally anyway.
Reported-by: NZaki Bakar <zaki.bm@gmail.com>
Tested-by: NChristian Lamparter <chunkeey@googlemail.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

We should not try to access hw if wakeup fails so add
proper error checking for that. Also add the timeout lenght
to the warning message.
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

This is consistent with all other functions.
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

Void pointers are bad, mmkay.

No functional changes.
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

It's easier to read t if the field names are visible.
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

It's much more readable if struct entries in host_ce_config_wlan
are explicitly set.
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

cacheline_sz is not used anywhere and can be removed.
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

The new naming makes more sense.
Signed-off-by: NMichal Kazior <michal.kazior@tieto.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

The new naming makes more sense.
Signed-off-by: NMichal Kazior <michal.kazior@tieto.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

Some parameters were unused and are not required.
They have no representation in firmware. Clean
them up.
Signed-off-by: NMichal Kazior <michal.kazior@tieto.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

Improve code readability by using enum and a
switch-case.
Signed-off-by: NMichal Kazior <michal.kazior@tieto.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

This fixes checkpatch warning from the latest
3.11-rc kernel tree.
Signed-off-by: NMichal Kazior <michal.kazior@tieto.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

Since the firmware support is no longer available for hw1.0,
drop all code (especially workarounds) for those units.
Signed-off-by: NBartosz Markowski <bartosz.markowski@tieto.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

Unify the PCI options location.

By default the SoC PS option is disabled to boost the
performance and due to poor stability on early HW revisions.
In future we can remove the module parameter and turn on/off
the PS for given hardware.

This change also makes the pci module parameter for SoC PS static.
Signed-off-by: NBartosz Markowski <bartosz.markowski@tieto.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

This fixes interrupt-related issue when no
interfaces were running thus the device was
considered powered down.

The power_down() function isn't really powering
down the device. It simply assumed it won't
interrupt. This wasn't true in some cases and
could lead to paging failures upon FW indication
interrupt (i.e. FW crash) because some structures
aren't allocated in that device state.

One reason for that was that ar_pci->started
wasn't reset. The other is interrupts should've
been masked when teardown starts.

The patch reorganized interrupt setup and makes
sure ar_pci->started is reset accordingly.
Reported-by: NBen Greear <greearb@candelatech.com>
Signed-off-by: NMichal Kazior <michal.kazior@tieto.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

pci_disable_msi() must be called if the initial
request_irq() fails.

Also add a warning message so it's possible to
distinguish request_irq() failure and
pci_enable_msi() failure.
Signed-off-by: NMichal Kazior <michal.kazior@tieto.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

Restart the hardware if FW crashes.

If FW crashes during recovery we leave the
hardware in a "wedged" state to avoid recursive
recoveries.

When in "wedged" state userspace may bring
interfaces down (to issue stop()) and then bring
one interface (to issue start()) to reload
hardware manually.
Signed-off-by: NMichal Kazior <michal.kazior@tieto.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

This fixes suspend-to-disk. The hardware is now
re-initialized upon freeze/thaw properly.

This also makes suspend/resume re-initialize the
hardware as WoWLAN support is not done yet.

With some little work it should be possible to
support hw reconfiguration for hw/fw recovery.

HW must be initialized once before registering to
mac80211 because FW determinates what hw
capabilities can be advertised.
Signed-off-by: NMichal Kazior <michal.kazior@tieto.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

Split up fw-related and hw-related suspension code.

Although we don't advertise WoW support to
mac80211 yet it's useful to keep the code in
suspend/resume hooks.

At this point there's no need to keep pci pm ops.
In case of WoW mac80211 calls ath10k_suspend()
which should take care of entering low-power mode.
In case WoW is not available mac80211 will go
through regular interface teradown and use start/stop.
Signed-off-by: NMichal Kazior <michal.kazior@tieto.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

Split logic that prepares the device for BMI
phase/cleans up related resources.

This is necessary for ath10k to be able to restart
hw on the fly without reloading the module.
Signed-off-by: NMichal Kazior <michal.kazior@tieto.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

The `set_callbacks` is a more appopriate name for
the function. Let's leave `init` for something
else.
Signed-off-by: NMichal Kazior <michal.kazior@tieto.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

This aligns it to the argument list of other
similar functions.
Signed-off-by: NMichal Kazior <michal.kazior@tieto.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>