The hardware time stamping code is a compile time option for the blackfin.
When it is not enabled, the driver should fall back to the standard
ethtool reply to the get_ts_info query.

Compile tested only.
Signed-off-by: NRichard Cochran <richardcochran@gmail.com>
Tested-by: NBob Liu <lliubbo@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch adds an ioctl for PTP Hardware Clock (PHC) devices that allows
user space to measure the time offset between the PHC and the system
clock. Rather than hard coding any kind of estimation algorithm into the
kernel, this patch takes the more flexible approach of just delivering
an array of raw clock readings. In that way, the user space clock servo
may be adapted to new and different hardware clocks.
Signed-off-by: NRichard Cochran <richardcochran@gmail.com>
Acked-by: NJacob Keller <jacob.e.keller@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Where a PTP clock driver is associated with a net or PHY driver, it
should be enabled automatically whenever that driver is enabled.
Therefore:

- Make PTP clock drivers select rather than depending on PTP_1588_CLOCK
- Remove separate boolean options for PTP clock drivers that are built
  as part of net driver modules.  (This also fixes cases where the PTP
  subsystem is wrongly forced to be built-in.)
- Set 'default y' for PTP clock drivers that depend on specific net
  drivers but are built separately
Signed-off-by: NBen Hutchings <bhutchings@solarflare.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

PTP hardware clock drivers that select PTP_1588_CLOCK must currently
also select PPS.  For those drivers that don't, the user must enable
PPS, then enable PTP_1588_CLOCK, then the driver.  Simplify things for
developers and users by putting this selection in one place.
Signed-off-by: NBen Hutchings <bhutchings@solarflare.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

These are now established subsystems, and we want drivers to be able
to select PPS and PTP_1588_CLOCK without depending on EXPERIMENTAL.
Further, the use of EXPERIMENTAL is now deprecated in general.
Signed-off-by: NBen Hutchings <bhutchings@solarflare.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The SO_ATTACH_FILTER option is set only. I propose to add the get
ability by using SO_ATTACH_FILTER in getsockopt. To be less
irritating to eyes the SO_GET_FILTER alias to it is declared. This
ability is required by checkpoint-restore project to be able to
save full state of a socket.

There are two issues with getting filter back.

First, kernel modifies the sock_filter->code on filter load, thus in
order to return the filter element back to user we have to decode it
into user-visible constants. Fortunately the modification in question
is interconvertible.

Second, the BPF_S_ALU_DIV_K code modifies the command argument k to
speed up the run-time division by doing kernel_k = reciprocal(user_k).
Bad news is that different user_k may result in same kernel_k, so we
can't get the original user_k back. Good news is that we don't have
to do it. What we need to is calculate a user2_k so, that

  reciprocal(user2_k) == reciprocal(user_k) == kernel_k

i.e. if it's re-loaded back the compiled again value will be exactly
the same as it was. That said, the user2_k can be calculated like this

  user2_k = reciprocal(kernel_k)

with an exception, that if kernel_k == 0, then user2_k == 1.

The optlen argument is treated like this -- when zero, kernel returns
the amount of sock_fprog elements in filter, otherwise it should be
large enough for the sock_fprog array.

changes since v1:
* Declared SO_GET_FILTER in all arch headers
* Added decode of vlan-tag codes
Signed-off-by: NPavel Emelyanov <xemul@parallels.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch implements a simple multiqueue flow steering policy - tx follows rx
for tun/tap. The idea is simple, it just choose the txq based on which rxq it
comes. The flow were identified through the rxhash of a skb, and the hash to
queue mapping were recorded in a hlist with an ageing timer to retire the
mapping. The mapping were created when tun receives packet from userspace, and
was quired in .ndo_select_queue().

I run co-current TCP_CRR test and didn't see any mapping manipulation helpers in
perf top, so the overhead could be negelected.
Signed-off-by: NJason Wang <jasowang@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Sometimes usespace may need to active/deactive a queue, this could be done by
detaching and attaching a file from tuntap device.

This patch introduces a new ioctls - TUNSETQUEUE which could be used to do
this. Flag IFF_ATTACH_QUEUE were introduced to do attaching while
IFF_DETACH_QUEUE were introduced to do the detaching.
Signed-off-by: NJason Wang <jasowang@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch converts tun/tap to a multiqueue devices and expose the multiqueue
queues as multiple file descriptors to userspace. Internally, each tun_file were
abstracted as a queue, and an array of pointers to tun_file structurs were
stored in tun_structure device, so multiple tun_files were allowed to be
attached to the device as multiple queues.

When choosing txq, we first try to identify a flow through its rxhash, if it
does not have such one, we could try recorded rxq and then use them to choose
the transmit queue. This policy may be changed in the future.
Signed-off-by: NJason Wang <jasowang@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add flags to be used by creating multiqueue tuntap device.
Signed-off-by: NJason Wang <jasowang@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

RCU were introduced in this patch to synchronize the dereferences between
tun_struct and tun_file. All tun_{get|put} were replaced with RCU, the
dereference from one to other must be done under rtnl lock or rcu read critical
region.

This is needed for the following patches since the one of the goal of multiqueue
tuntap is to allow adding or removing queues during workload. Without RCU,
control path would hold tx locks when adding or removing queues (which may cause
sme delay) and it's hard to change the number of queues without stopping the net
device. With the help of rcu, there's also no need for tun_file hold an refcnt
to tun_struct.
Signed-off-by: NJason Wang <jasowang@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Current tuntap makes use of the socket receive queue as its tx queue. To
implement multiple tx queues for tuntap and enable the ability of adding and
removing queues during workload, the first step is to move the socket related
structures to tun_file. Then we could let multiple fds/sockets to be attached to
the tuntap.

This patch removes tun_sock and moves socket related structures from tun_sock or
tun_struct to tun_file. Two exceptions are tap_filter and sock_fprog, they are
still kept in tun_structure since they are used to filter packets for the net
device instead of per transmit queue (at least I see no requirements for
them). After those changes, socket were created and destroyed during file open
and close (instead of device creation and destroy), the socket structures could
be dereferenced from tun_file instead of the file of tun_struct structure
itself.

For persisent device, since we purge during datching and wouldn't queue any
packets when no interface were attached, there's no behaviod changes before and
after this patch, so the changes were transparent to the userspace. To keep the
attributes such as sndbuf, socket filter and vnet header, those would be
re-initialize after a new interface were attached to an persist device.
Signed-off-by: NJason Wang <jasowang@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NJason Wang <jasowang@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Jeff Kirsher says:

====================
This series contains updates to ixgbe, ixgbevf, igbvf, igb and
networking core (bridge).  Most notably is the addition of support
for local link multicast addresses in SR-IOV mode to the networking
core.

Also note, the ixgbe patch "ixgbe: Add support for pipeline reset" and
"ixgbe: Fix return value from macvlan filter function" is revised based
on community feedback.
====================
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

dev_<level> calls take less code than dev_printk(KERN_<LEVEL>
and reducing object size is good.
Coalesce formats for easier grep.
Signed-off-by: NJoe Perches <joe@perches.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch is a follow-up for patch "net: filter: add vlan tag access"
to support the new VLAN_TAG/VLAN_TAG_PRESENT accessors in BPF JIT.
Signed-off-by: NEric Dumazet <edumazet@google.com>
Cc: Ani Sinha <ani@aristanetworks.com>
Cc: Daniel Borkmann <danborkmann@iogearbox.net>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

BPF filters lack ability to access skb->vlan_tci

This patch adds two new ancillary accessors :

SKF_AD_VLAN_TAG         (44) mapped to vlan_tx_tag_get(skb)

SKF_AD_VLAN_TAG_PRESENT (48) mapped to vlan_tx_tag_present(skb)

This allows libpcap/tcpdump to use a kernel filter instead of
having to fallback to accept all packets, then filter them in
user space.
Signed-off-by: NEric Dumazet <edumazet@google.com>
Suggested-by: NAni Sinha <ani@aristanetworks.com>
Suggested-by: NDaniel Borkmann <danborkmann@iogearbox.net>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Fixes the following build failure on S390:
  In file included from drivers/net/ethernet/cadence/at91_ether.c:35:0:
   drivers/net/ethernet/cadence/macb.h: In function 'macb_is_gem':
   drivers/net/ethernet/cadence/macb.h:563:2: error: implicit declaration of function '__raw_readl' [-Werror=implicit-function-declaration]
   drivers/net/ethernet/cadence/at91_ether.c: In function 'update_mac_address':
   drivers/net/ethernet/cadence/at91_ether.c:119:2: error: implicit declaration of function '__raw_writel' [-Werror=implicit-function-declaration]
   cc1: some warnings being treated as errors
Reported-by: NFengguang Wu <fengguang.wu@intel.com>
Signed-off-by: NJoachim Eastwood <manabian@gmail.com>
Acked-by: NNicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The hardware doesn't support controlling pause frames autoneg, so
report that back correctly to userspace.
Signed-off-by: NFlavio Leitner <fbl@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Trivial. Only used in one file.
Signed-off-by: NStephen Hemminger <shemminger@vyatta.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Network device drivers can communicate a Toeplitz hash in skb->rxhash,
but devices differ in their hashing capabilities. All compute a 5-tuple
hash for TCP over IPv4, but for other connection-oriented protocols,
they may compute only a 3-tuple. This breaks RPS load balancing, e.g.,
for TCP over IPv6 flows. Additionally, for GRE and other tunnels,
the kernel computes a 5-tuple hash over the inner packet if possible,
but devices do not.

This patch recomputes the rxhash in software in all cases where it
cannot be certain that a 5-tuple was computed. Device drivers can avoid
recomputation by setting the skb->l4_rxhash flag.

Recomputing adds cycles to each packet when RPS is enabled or the
packet arrives over a tunnel. A comparison of 200x TCP_STREAM between
two servers running unmodified netnext with rxhash computation
in hardware vs software (using ethtool -K eth0 rxhash [on|off]) shows
how much time is spent in __skb_get_rxhash in this worst case:

     0.03%          swapper  [kernel.kallsyms]     [k] __skb_get_rxhash
     0.03%          swapper  [kernel.kallsyms]     [k] __skb_get_rxhash
     0.05%          swapper  [kernel.kallsyms]     [k] __skb_get_rxhash

With 200x TCP_RR it increases to

     0.10%          netperf  [kernel.kallsyms]     [k] __skb_get_rxhash
     0.10%          netperf  [kernel.kallsyms]     [k] __skb_get_rxhash
     0.10%          netperf  [kernel.kallsyms]     [k] __skb_get_rxhash

I considered having the patch explicitly skips recomputation when it knows
that it will not improve the hash (TCP over IPv4), but that conditional
complicates code without saving many cycles in practice, because it has
to take place after flow dissector.
Signed-off-by: NWillem de Bruijn <willemb@google.com>
Acked-by: NEric Dumazet <edumazet@google.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

use the module_pci_driver macro to make the code simpler
by eliminating module_init and module_exit calls.
Signed-off-by: NDevendra Naga <devendra.aaru@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

use the module_pci_driver macro to make the code simpler
by eliminating the module_init and module_exit calls
Signed-off-by: NDevendra Naga <devendra.aaru@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

included changes:
- some code cleanups and minor fixes (3 of them were reported by Coverity)
- 'struct hard_iface' re-shaping to improve multi-protocol support
- ECTP packets silent drop
- transfer the WIFI flag on clients in case of roaming

The variable retval is initialized but never used
otherwise, so remove the unused variable.

dpatch engine is used to auto generate this patch.
(https://github.com/weiyj/dpatch)
Signed-off-by: NWei Yongjun <yongjun_wei@trendmicro.com.cn>
Acked-by: NJitendra Kalsaria <jitendra.kalsaria@qlogic.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Use the module_pci_driver() macro to make the code simpler
by eliminating module_init and module_exit calls.

dpatch engine is used to auto generate this patch.
(https://github.com/weiyj/dpatch)
Signed-off-by: NWei Yongjun <yongjun_wei@trendmicro.com.cn>
Acked-by: NJitendra Kalsaria <jitendra.kalsaria@qlogic.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch adds support for wol wakeup on unicast, broadcast,
multicast and arp frames.

The wakeup filter code isn't pretty, but it works.
Signed-off-by: NSteve Glendinning <steve.glendinning@shawell.net>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

adds a "hwaddr" to the "IP-Config: Complete" KERN_INFO message
with the dev_addr of the device selected for auto configuration.
Signed-off-by: NClaudio Fontana <claudio.fontana@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This adds support for the net device ops to manage the embedded
hardware bridge on ixgbe devices. With this patch the bridge
mode can be toggled between VEB and VEPA to support stacking
macvlan devices or using the embedded switch without any SW
component in 802.1Qbg/br environments.

Additionally, this adds source address pruning to the ixgbevf
driver to prune any frames sent back from a reflective relay on
the switch. This is required because the existing hardware does
not support this. Without it frames get pushed into the stack
with its own src mac which is invalid per 802.1Qbg VEPA
definition.
Signed-off-by: NJohn Fastabend <john.r.fastabend@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Hardware switches may support enabling and disabling the
loopback switch which puts the device in a VEPA mode defined
in the IEEE 802.1Qbg specification. In this mode frames are
not switched in the hardware but sent directly to the switch.
SR-IOV capable NICs will likely support this mode I am
aware of at least two such devices. Also I am told (but don't
have any of this hardware available) that there are devices
that only support VEPA modes. In these cases it is important
at a minimum to be able to query these attributes.

This patch adds an additional IFLA_BRIDGE_MODE attribute that can be
set and dumped via the PF_BRIDGE:{SET|GET}LINK operations. Also
anticipating bridge attributes that may be common for both embedded
bridges and software bridges this adds a flags attribute
IFLA_BRIDGE_FLAGS currently used to determine if the command or event
is being generated to/from an embedded bridge or software bridge.
Finally, the event generation is pulled out of the bridge module and
into rtnetlink proper.

For example using the macvlan driver in VEPA mode on top of
an embedded switch requires putting the embedded switch into
a VEPA mode to get the expected results.

	--------  --------
        | VEPA |  | VEPA |       <-- macvlan vepa edge relays
        --------  --------
           |        |
           |        |
        ------------------
        |      VEPA      |       <-- embedded switch in NIC
        ------------------
                |
                |
        -------------------
        | external switch |      <-- shiny new physical
	-------------------          switch with VEPA support

A packet sent from the macvlan VEPA at the top could be
loopbacked on the embedded switch and never seen by the
external switch. So in order for this to work the embedded
switch needs to be set in the VEPA state via the above
described commands.

By making these attributes nested in IFLA_AF_SPEC we allow
future extensions to be made as needed.

CC: Lennert Buytenhek <buytenh@wantstofly.org>
CC: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: NJohn Fastabend <john.r.fastabend@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The PF_BRIDGE:RTM_{GET|SET}LINK nlmsg family and type are
currently embedded in the ./net/bridge module. This prohibits
them from being used by other bridging devices. One example
of this being hardware that has embedded bridging components.

In order to use these nlmsg types more generically this patch
adds two net_device_ops hooks. One to set link bridge attributes
and another to dump the current bride attributes.

	ndo_bridge_setlink()
	ndo_bridge_getlink()

CC: Lennert Buytenhek <buytenh@wantstofly.org>
CC: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: NJohn Fastabend <john.r.fastabend@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This change fixes a sparse warning triggered by us casting the timestamp in
the packet as a u64 instead of as a __le64.  This change corrects that in
order to resolve the sparse warning.
Signed-off-by: NAlexander Duyck <alexander.h.duyck@intel.com>
Tested-by: NAaron Brown <aaron.f.brown@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

There are multiple places in our device nvm where the version is stored.
This update fixes some output errors with some types of images and
refactors the way the version data is gathered and stored for ethtool output.
Signed-off-by: NCarolyn Wyborny <carolyn.wyborny@intel.com>
Tested-by: NAaron Brown <aaron.f.brown@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Newer devices supported by igb can support auto-crossover detection in
forced operation modes. Enable this in the driver, rather than clobbering
this functionality in forced operation.
Signed-off-by: NMatthew Vick <matthew.vick@intel.com>
Tested-by: NAaron Brown <aaron.f.brown@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Ignoring the return value from a call to the kernel dma_map API functions
can cause data corruption and system instability.  Check the return value
and take appropriate action.
Signed-off-by: NGreg Rose <gregory.v.rose@intel.com>
Tested-by: NSibai Li <sibai.li@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

The driver should not forward LLDP type frames.  Inspect the ether type and
do not send if it is an LLDP ethertype frame.
Signed-off-by: NGreg Rose <gregory.v.rose@intel.com>
Tested-by: NSibai Li <sibai.li@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Hw timestamping code caused performance regression in ixgbe driver when the
timestamping is not enabled. The culprit is IXGBE_READ_REG call in the Rx
path which is executed for every received skb. This call is not needed when
the timestamping is disabled or for non-ptp packets.

netperf results:

The ixgbe side of the connection was acting as a server, the netperf command
line on the other side was:
netperf -H 192.168.1.23 -T0,0 -t UDP_STREAM -l 20

The values below mean throughput as reported by netperf (local/remote), for
3 runs, with timestamping not enabled.

3.7.0-rc1+ with CONFIG_IXGBE_PTP off:
5373.83 / 3329.32
5721.88 / 3033.89
5653.42 / 3112.38

3.7.0-rc1+ with CONFIG_IXGBE_PTP on:
5233.64 / 1226.85
5448.67 / 1039.32
5421.36 / 1095.66

Patched 3.7.0-rc1+ with CONFIG_IXGBE_PTP on:
5594.72 / 2942.53
5428.95 / 3110.16
5343.56 / 3200.48
Reported-by: NJesper Brouer <jbrouer@redhat.com>
Signed-off-by: NJiri Benc <jbenc@redhat.com>
Signed-off-by: NAndy Gospodarek <gospo@redhat.com>
Tested-by: NPhil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Adds/updates ASCII descriptor maps for 82598 and 82599 Tx/Rx descriptors.
Current descriptor maps were out of date for 82598 and incorrect for
82599.
Signed-off-by: NJosh Hay <joshua.a.hay@intel.com>
Tested-by: NPhil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This change makes it so that compare the total_rx_packets cleaned to budget
instead of decrementing budget.  The advantage to this approach is that budget
can now be const and we only end up modifying total_rx_packets instead of
modifying both it and budget.
Signed-off-by: NAlexander Duyck <alexander.h.duyck@intel.com>
Tested-by: NPhil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

When setting a MAC filter for the VF the function should return a success
or failure code, not the index of the new filter.  It causes spurious NACK
returns to the VF driver.
Signed-off-by: NGreg Rose <gregory.v.rose@intel.com>
Tested-by: NPhil Schmitt <phillip.j.schmitt@intel.com>
Tested-by: NSibai Li <sibai.li@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>