By default, when uapsd is not used, the ucode uses
null data packet to exit power-save and get then
pending frames.

However, some tests require the explicit usage of ps-poll.
Allow setting use_ps_poll power option (through debugfs)
to configure the ucode to use ps-poll instead.

The ucode configuration is done by setting the advanced-pm
flag while setting all the ACs to non-upasd mode.
Signed-off-by: NEliad Peller <eliadx.peller@intel.com>
Reviewed-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

This allows to force the GO to use protection and enhances
the reliability of the link.
Reviewed-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

This allows to leave a frame in the Tx Fifo which allows
the firmware to try to enter burst mode.
The end result of this is a better latency since the
firmware utilises the TxOP better.

Also limit the AMPDU size to the limit set in the ADDBA
response. This doesn't change much since the AMPDU size
was limited by the configuration of the hardware scheduler,
but here we add a software limit by the mean of the link
quality command.
Reviewed-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

Add ability to set the NIC's temperature and ignore the actual temperature
that the FW supplies.
Signed-off-by: NMatti Gottlieb <matti.gottlieb@intel.com>
Reviewed-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

Pull networking fixes from David Miller:
 "Here are some bug fixes that have piled up during ksummit/linuxcon.

   1) Fix endian problems in ibmveth, from Anton Blanchard.

   2) IPV6 routing code does GFP_KERNEL allocation in atomic, fix from
      Benjamin Block.

   3) SCTP association fixes from Daniel Borkmann.

   4) When multiple VLAN headers are present we have to make sure the
      second and subsequent ones are pullable in the SKB otherwise we
      blindly dereference garbage.  From Jiri Benc.

   5) The argument adjustment of the signature of hlist_add_after*()
      introduced a regression in the batman-adv code, fix from Sven
      Eckelmann.

   6) Fix TX hang handling to avoid a panic in i40e, from Anjali Singhai
      Jain.

   7) PTP flag test is inverted in i40e driver, from Jesse Brandeburg.

   8) ATM LEC driver needs to hold RTNL mutex over MTU changes, from
      Chas Williams.

   9) Truncate packets larger then the TPACKET_V3 format configured
      buffers, otherwise we overwrite past the end of said buffers.
      From Eric Dumazet.

  10) Fix endianness bugs in qlcnic firmware handling, from Rajesh
      Borundia and Shahed Shaikh.

  11) CXGB4 sometimes doesn't get all of the TX completion events it
      should resulting in SKBs getting stuck in the TX queue, from
      Hariprasad Shenai.

  12) When the FEC chip's PTP clock is disabled, you can't access the
      register.  Add necessary checks to avoid the resulting hang, from
      Fugang Duan"

* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (37 commits)
  drivers: isdn: eicon: xdi_msg.h: Fix typo in #ifndef
  net: sctp: fix suboptimal edge-case on non-active active/retrans path selection
  net: sctp: spare unnecessary comparison in sctp_trans_elect_best
  net: ethernet: broadcom: bnx2x: Remove redundant #ifdef
  ibmveth: Fix endian issues with rx_no_buffer statistic
  net: xgene: fix possible NULL dereference in xgene_enet_free_desc_rings()
  openvswitch: fix panic with multiple vlan headers
  net: ipv6: fib: don't sleep inside atomic lock
  net: fec: ptp: avoid register access when ipg clock is disabled
  cxgb4: Free completed tx skbs promptly
  cxgb4: Fix race condition in cleanup
  sctp: not send SCTP_PEER_ADDR_CHANGE notifications with failed probe
  bnx2x: Revert UNDI flushing mechanism
  qlcnic: Fix endianess issue in firmware load from file operation
  qlcnic: Fix endianess issue in FW dump template header
  qlcnic: Fix flash access interface to application
  MAINTAINERS: Add section for MRF24J40 IEEE 802.15.4 radio driver
  macvlan: Allow setting multicast filter on all macvlan types
  packet: handle too big packets for PACKET_V3
  MAINTAINERS: add entry for ec_bhf driver
  ...

Test for definedness of the macro which is actually defined (the
change is hard to see: it is s/SSS/SSA/).
Signed-off-by: NRasmus Villemoes <linux@rasmusvillemoes.dk>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

In SCTP, selection of active (T.ACT) and retransmission (T.RET)
transports is being done whenever transport control operations
(UP, DOWN, PF, ...) are engaged through sctp_assoc_control_transport().

Commits 4c47af4d ("net: sctp: rework multihoming retransmission
path selection to rfc4960") and a7288c4d ("net: sctp: improve
sctp_select_active_and_retran_path selection") have both improved
it towards a more fine-grained and optimal path selection.

Currently, the selection algorithm for T.ACT and T.RET is as follows:

1) Elect the two most recently used ACTIVE transports T1, T2 for
   T.ACT, T.RET, where T.ACT<-T1 and T1 is most recently used
2) In case primary path T.PRI not in {T1, T2} but ACTIVE, set
   T.ACT<-T.PRI and T.RET<-T1
3) If only T1 is ACTIVE from the set, set T.ACT<-T1 and T.RET<-T1
4) If none is ACTIVE, set T.ACT<-best(T.PRI, T.RET, T3) where
   T3 is the most recently used (if avail) in PF, set T.RET<-T.PRI

Prior to above commits, 4) was simply a camp on T.ACT<-T.PRI and
T.RET<-T.PRI, ignoring possible paths in PF. Camping on T.PRI is
still slightly suboptimal as it can lead to the following scenario:

Setup:
        <A>                                <B>
    T1: p1p1 (10.0.10.10) <==>  .'`)  <==> p1p1 (10.0.10.12)  <= T.PRI
    T2: p1p2 (10.0.10.20) <==> (_ . ) <==> p1p2 (10.0.10.22)

    net.sctp.rto_min = 1000
    net.sctp.path_max_retrans = 2
    net.sctp.pf_retrans = 0
    net.sctp.hb_interval = 1000

T.PRI is permanently down, T2 is put briefly into PF state (e.g. due to
link flapping). Here, the first time transmission is sent over PF path
T2 as it's the only non-INACTIVE path, but the retransmitted data-chunks
are sent over the INACTIVE path T1 (T.PRI), which is not good.

After the patch, it's choosing better transports in both cases by
modifying step 4):

4) If none is ACTIVE, set T.ACT_new<-best(T.ACT_old, T3) where T3 is
   the most recently used (if avail) in PF, set T.RET<-T.ACT_new

This will still select a best possible path in PF if available (which
can also include T.PRI/T.RET), and set both T.ACT/T.RET to it.

In case sctp_assoc_control_transport() *just* put T.ACT_old into INACTIVE
as it transitioned from ACTIVE->PF->INACTIVE and stays in INACTIVE just
for a very short while before going back ACTIVE, it will guarantee that
this path will be reselected for T.ACT/T.RET since T3 (PF) is not
available.

Previously, this was not possible, as we would only select between T.PRI
and T.RET, and a possible T3 would be NULL due to the fact that we have
just transitioned T3 in sctp_assoc_control_transport() from PF->INACTIVE
and would select a suboptimal path when T.PRI/T.RET have worse properties.

In the case that T.ACT_old permanently went to INACTIVE during this
transition and there's no PF path available, plus T.PRI and T.RET are
INACTIVE as well, we would now camp on T.ACT_old, but if everything is
being INACTIVE there's really not much we can do except hoping for a
successful HB to bring one of the transports back up again and, thus
cause a new selection through sctp_assoc_control_transport().

Now both tests work fine:

Case 1:

 1. T1 S(ACTIVE) T.ACT
    T2 S(ACTIVE) T.RET

 2. T1 S(ACTIVE) T.ACT, T.RET
    T2 S(PF)

 3. T1 S(ACTIVE) T.ACT, T.RET
    T2 S(INACTIVE)

 5. T1 S(PF) T.ACT, T.RET
    T2 S(INACTIVE)

[ 5.1 T1 S(INACTIVE) T.ACT, T.RET
      T2 S(INACTIVE) ]

 6. T1 S(ACTIVE) T.ACT, T.RET
    T2 S(INACTIVE)

 7. T1 S(ACTIVE) T.ACT
    T2 S(ACTIVE) T.RET

Case 2:

 1. T1 S(ACTIVE) T.ACT
    T2 S(ACTIVE) T.RET

 2. T1 S(PF)
    T2 S(ACTIVE) T.ACT, T.RET

 3. T1 S(INACTIVE)
    T2 S(ACTIVE) T.ACT, T.RET

 5. T1 S(INACTIVE)
    T2 S(PF) T.ACT, T.RET

[ 5.1 T1 S(INACTIVE)
      T2 S(INACTIVE) T.ACT, T.RET ]

 6. T1 S(INACTIVE)
    T2 S(ACTIVE) T.ACT, T.RET

 7. T1 S(ACTIVE) T.ACT
    T2 S(ACTIVE) T.RET
Signed-off-by: NDaniel Borkmann <dborkman@redhat.com>
Acked-by: NNeil Horman <nhorman@tuxdriver.com>
Acked-by: NVlad Yasevich <vyasevich@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When both transports are the same, we don't have to go down that
road only to realize that we will return the very same transport.
We are guaranteed that curr is always non-NULL. Therefore, just
short-circuit this special case.
Signed-off-by: NDaniel Borkmann <dborkman@redhat.com>
Acked-by: NNeil Horman <nhorman@tuxdriver.com>
Acked-by: NVlad Yasevich <vyasevich@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Nothing defines _ASM_GENERIC_INT_L64_H, it is a weird way to check for
64 bit longs, and u64 should be printed using %llx anyway.
Signed-off-by: NRasmus Villemoes <linux@rasmusvillemoes.dk>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Hidden away in the last 8 bytes of the buffer_list page is a solitary
statistic. It needs to be byte swapped or else ethtool -S will
produce numbers that terrify the user.

Since we do this in multiple places, create a helper function with a
comment explaining what is going on.
Signed-off-by: NAnton Blanchard <anton@samba.org>
Cc: stable@vger.kernel.org
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

A NULL pointer dereference is possible for the argument ring->buf_pool
which is passed to xgene_enet_free_desc_ring(), as ring could be NULL.

And now since NULL pointers are being checked for before the calls to
xgene_enet_free_desc_ring(), might as well take advantage of them and
not call the function if the argument would be NULL.
Reported-by: NDan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: NIyappan Subramanian <isubramanian@apm.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When there are multiple vlan headers present in a received frame, the first
one is put into vlan_tci and protocol is set to ETH_P_8021Q. Anything in the
skb beyond the VLAN TPID may be still non-linear, including the inner TCI
and ethertype. While ovs_flow_extract takes care of IP and IPv6 headers, it
does nothing with ETH_P_8021Q. Later, if OVS_ACTION_ATTR_POP_VLAN is
executed, __pop_vlan_tci pulls the next vlan header into vlan_tci.

This leads to two things:

1. Part of the resulting ethernet header is in the non-linear part of the
   skb. When eth_type_trans is called later as the result of
   OVS_ACTION_ATTR_OUTPUT, kernel BUGs in __skb_pull. Also, __pop_vlan_tci
   is in fact accessing random data when it reads past the TPID.

2. network_header points into the ethernet header instead of behind it.
   mac_len is set to a wrong value (10), too.
Reported-by: NYulong Pei <ypei@redhat.com>
Signed-off-by: NJiri Benc <jbenc@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The function fib6_commit_metrics() allocates a piece of memory in mode
GFP_KERNEL while holding an atomic lock from higher up in the stack, in
the function __ip6_ins_rt(). This produces the following BUG:

> BUG: sleeping function called from invalid context at mm/slub.c:1250
> in_atomic(): 1, irqs_disabled(): 0, pid: 2909, name: dhcpcd
> 2 locks held by dhcpcd/2909:
>  #0:  (rtnl_mutex){+.+.+.}, at: [<ffffffff81978e67>] rtnl_lock+0x17/0x20
>  #1:  (&tb->tb6_lock){++--+.}, at: [<ffffffff81a6951a>] ip6_route_add+0x65a/0x800
> CPU: 1 PID: 2909 Comm: dhcpcd Not tainted 3.17.0-rc1 #1
> Hardware name: ASUS All Series/Q87T, BIOS 0216 10/16/2013
>  0000000000000008 ffff8800c8f13858 ffffffff81af135a 0000000000000000
>  ffff880212202430 ffff8800c8f13878 ffffffff810f8d3a ffff880212202c98
>  0000000000000010 ffff8800c8f138c8 ffffffff8121ad0e 0000000000000001
> Call Trace:
>  [<ffffffff81af135a>] dump_stack+0x4e/0x68
>  [<ffffffff810f8d3a>] __might_sleep+0x10a/0x120
>  [<ffffffff8121ad0e>] kmem_cache_alloc_trace+0x4e/0x190
>  [<ffffffff81a6bcd6>] ? fib6_commit_metrics+0x66/0x110
>  [<ffffffff81a6bcd6>] fib6_commit_metrics+0x66/0x110
>  [<ffffffff81a6cbf3>] fib6_add+0x883/0xa80
>  [<ffffffff81a6951a>] ? ip6_route_add+0x65a/0x800
>  [<ffffffff81a69535>] ip6_route_add+0x675/0x800
>  [<ffffffff81a68f2a>] ? ip6_route_add+0x6a/0x800
>  [<ffffffff81a6990c>] inet6_rtm_newroute+0x5c/0x80
>  [<ffffffff8197cf01>] rtnetlink_rcv_msg+0x211/0x260
>  [<ffffffff81978e67>] ? rtnl_lock+0x17/0x20
>  [<ffffffff81119708>] ? lock_release_holdtime+0x28/0x180
>  [<ffffffff81978e67>] ? rtnl_lock+0x17/0x20
>  [<ffffffff8197ccf0>] ? __rtnl_unlock+0x20/0x20
>  [<ffffffff819a989e>] netlink_rcv_skb+0x6e/0xd0
>  [<ffffffff81978ee5>] rtnetlink_rcv+0x25/0x40
>  [<ffffffff819a8e59>] netlink_unicast+0xd9/0x180
>  [<ffffffff819a9600>] netlink_sendmsg+0x700/0x770
>  [<ffffffff81103735>] ? local_clock+0x25/0x30
>  [<ffffffff8194e83c>] sock_sendmsg+0x6c/0x90
>  [<ffffffff811f98e3>] ? might_fault+0xa3/0xb0
>  [<ffffffff8195ca6d>] ? verify_iovec+0x7d/0xf0
>  [<ffffffff8194ec3e>] ___sys_sendmsg+0x37e/0x3b0
>  [<ffffffff8111ef15>] ? trace_hardirqs_on_caller+0x185/0x220
>  [<ffffffff81af979e>] ? mutex_unlock+0xe/0x10
>  [<ffffffff819a55ec>] ? netlink_insert+0xbc/0xe0
>  [<ffffffff819a65e5>] ? netlink_autobind.isra.30+0x125/0x150
>  [<ffffffff819a6520>] ? netlink_autobind.isra.30+0x60/0x150
>  [<ffffffff819a84f9>] ? netlink_bind+0x159/0x230
>  [<ffffffff811f989a>] ? might_fault+0x5a/0xb0
>  [<ffffffff8194f25e>] ? SYSC_bind+0x7e/0xd0
>  [<ffffffff8194f8cd>] __sys_sendmsg+0x4d/0x80
>  [<ffffffff8194f912>] SyS_sendmsg+0x12/0x20
>  [<ffffffff81afc692>] system_call_fastpath+0x16/0x1b

Fixing this by replacing the mode GFP_KERNEL with GFP_ATOMIC.
Signed-off-by: NBenjamin Block <bebl@mageta.org>
Acked-by: NDavid Rientjes <rientjes@google.com>
Acked-by: NHannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The current kernel hang on i.MX6SX with rootfs mount from MMC.
The root cause is that ptp uses a periodic timer to access enet register
even if ipg clock is disabled.

FEC ptp driver start one period timer to read 1588 counter register in the
ptp init function that is called after FEC driver is probed.

To save power, after FEC probe finish, FEC driver disable all clocks including
ipg clock that is needed for register access.

i.MX5x, i.MX6q/dl/sl FEC register access don't cause system hang when ipg clock
is disabled, just return zero value. But for i.MX6sx SOC, it cause system hang.

To avoid the issue, we need to check ptp clock status before ptp timer count access.
Signed-off-by: NFugang Duan <B38611@freescale.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Pull arm64 fixes from Will Deacon:
 "This small set of fixes addresses a few issues introduced during the
  merge window, including:

   - fix typo in I-cache detection that was causing us to treat all
     I-caches as aliasing
   - hook up memfd_create and getrandom syscalls for native and compat
   - revert a temporary hack for defconfig builds in -next (the audit
     tree changes didn't make it in this merge window)
   - a couple of UEFI fixes for TEXT_OFFSET fuzzing and /memreserve/
   - a simple sparsemem fix for 48-bit physical addressing
   - small defconfig updates to get autotesters working with X-gene"

* tag 'arm64-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux:
  Revert "arm64: Do not invoke audit_syscall_* functions if !CONFIG_AUDIT_SYSCALL"
  arm64: mm: update max pa bits to 48
  arm64: ignore DT memreserve entries when booting in UEFI mode
  arm64: configs: Enable X-Gene SATA and ethernet in defconfig
  arm64: align randomized TEXT_OFFSET on 4 kB boundary
  asm-generic: add memfd_create system call to unistd.h
  arm64: compat: wire up memfd_create and getrandom syscalls for aarch32
  arm64: fix typo in I-cache policy detection

Pull IOMMU fixes from Joerg Roedel:
 "The fixes include:

   - fix a crash in the VT-d driver when devices with a driver attached
     are hot-unplugged

   - fix a AMD IOMMU driver crash with device assignment of 32 bit PCI
     devices to KVM guests

   - fix for a copy&paste error in generic IOMMU code.  Now the right
     function pointer is checked before calling"

* tag 'iommu-fixes-v3.17-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/joro/iommu:
  iommu/core: Check for the right function pointer in iommu_map()
  iommu/amd: Fix cleanup_domain for mass device removal
  iommu/vt-d: Defer domain removal if device is assigned to a driver

Description of problem:
The NIC card is not reporting back to the driver the transmitted skbs,
so they get stuck in the TX ring causing issues with reference
counters in other kernel components.

Developed a new Automatic Egress Queue Update firmware facility to slowly tick
through Egress Queues and send back any outstanding CIDX Updates which are
laying around.

Based on original work by Casey Leedom <leedom@chelsio.com>
Signed-off-by: NHariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Marc Kleine-Budde says:

====================
pull-request: can 2014-08-21

The first patch is from Mirza Krak, it fixes the initialization of the hardware
in the sja1000 driver. The next patch is contributed by Dan Carpenter, it fixes
the error handling in the c_can's probe function. Then there are two patches
for the flexcan driver, one by Alexander Stein, which fixes the resetting of
the bus error interrupt mask, the other one by Sebastian Andrzej Siewior which
adds an additional error state transition message.
====================
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

There is a possible race condition when we unregister the PCI Driver and then
flush/destroy the global "workq". This could lead to situations where there
are tasks on the Work Queue with references to now deleted adapter data
structures. Instead, have per-adapter Work Queues which were instantiated and
torn down in init_one() and remove_one(), respectively.

v2: Remove unnecessary call to flush_workqueue() before destroy_workqueue()
Signed-off-by: NAnish Bhatt <anish@chelsio.com>
Signed-off-by: NCasey Leedom <leedom@chelsio.com>
Acked-by: NNeil Horman <nhorman@tuxdriver.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Since the transport has always been in state SCTP_UNCONFIRMED, it
therefore wasn't active before and hasn't been used before, and it
always has been, so it is unnecessary to bug the user with a
notification.
Reported-by: NDeepak Khandelwal <khandelwal.deepak.1987@gmail.com>
Suggested-by: NVlad Yasevich <vyasevich@gmail.com>
Suggested-by: NMichael Tuexen <tuexen@fh-muenster.de>
Suggested-by: NDaniel Borkmann <dborkman@redhat.com>
Signed-off-by: NZhu Yanjun <Yanjun.Zhu@windriver.com>
Acked-by: NVlad Yasevich <vyasevich@gmail.com>
Acked-by: NDaniel Borkmann <dborkman@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Commit 91ebb929 ("bnx2x: Add support for Multi-Function UNDI") [which was
later supposedly fixed by de682941 ("bnx2x: Fix UNDI driver unload")]
introduced a bug in which in some [yet-to-be-determined] scenarios the
alternative flushing mechanism which was to guarantee the Rx buffers are
empty before resetting them during device probe will fail.
If this happens, when device will be loaded once more a fatal attention will
occur; Since this most likely happens in boot from SAN scenarios, the machine
will fail to load.

Notice this may occur not only in the 'Multi-Function' scenario but in the
regular scenario as well, i.e., this introduced a regression in the driver's
ability to perform boot from SAN.

The patch reverts the mechanism and applies the old scheme to multi-function
devices as well as to single-function devices.
Signed-off-by: NYuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: NAriel Elior <Ariel.Elior@qlogic.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Shahed Shaikh says:

====================
qlcnic: Bug fixes

This series fixes some bugs related to endianess.

Please apply this series to net.
====================
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Firmware binary file is in little endian. On big-endian architecture, while
writing this binary FW file to adapters memory, writel() swaps the data resulting into
corruption of FW image. So, swap the data before writing into adapters memory.
Signed-off-by: NShahed Shaikh <shahed.shaikh@qlogic.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Firmware dump template header is read from adapter using
readl() which swaps the data. So, adjust structure
element on the boundary of 32bit dword.
Signed-off-by: NRajesh Borundia <rajesh.borundia@qlogic.com>
Signed-off-by: NShahed Shaikh <shahed.shaikh@qlogic.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Application expects flash data in little endian, but driver reads/writes
flash data using readl()/writel() APIs which swaps data on big endian machine.
So, swap the data after reading from and before writing to flash memory.
Signed-off-by: NJitendra Kalsaria <jitendra.kalsaria@qlogic.com>
Signed-off-by: NShahed Shaikh <shahed.shaikh@qlogic.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Alan is the original author of the driver. This change was discussed
with the 802.15.4 subsystem maintainer, Alexander Aring.
Signed-off-by: NAlan Ott <alan@signal11.us>
Acked-by: NAlexander Aring <alex.aring@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Currently, macvlan code restricts multicast and unicast
filter setting only to passthru devices.  As a result,
if a guest using macvtap wants to receive multicast
traffic, it has to set IFF_ALLMULTI or IFF_PROMISC.

This patch makes it possible to use the fdb interface
to add multicast addresses to the filter thus allowing
a guest to receive only targeted multicast traffic.

CC: John Fastabend <john.r.fastabend@intel.com>
CC: Michael S. Tsirkin <mst@redhat.com>
CC: Jason Wang <jasowang@redhat.com>
Signed-off-by: NVladislav Yasevich <vyasevic@redhat.com>
Acked-by: NJohn Fastabend <john.r.fastabend@intel.com>
Acked-by: NMichael S. Tsirkin <mst@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

af_packet can currently overwrite kernel memory by out of bound
accesses, because it assumed a [new] block can always hold one frame.

This is not generally the case, even if most existing tools do it right.

This patch clamps too long frames as API permits, and issue a one time
error on syslog.

[  394.357639] tpacket_rcv: packet too big, clamped from 5042 to 3966. macoff=82

In this example, packet header tp_snaplen was set to 3966,
and tp_len was set to 5042 (skb->len)
Signed-off-by: NEric Dumazet <edumazet@google.com>
Fixes: f6fb8f10 ("af-packet: TPACKET_V3 flexible buffer implementation.")
Acked-by: NDaniel Borkmann <dborkman@redhat.com>
Acked-by: NNeil Horman <nhorman@tuxdriver.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Added entry for ec_bhf driver.
Signed-off-by: NDariusz Marcinkiewicz <reksio@newterm.pl>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The LECS response contains the MTU that should be used.  Correctly
synchronize with other layers when updating.
Signed-off-by: NChas Williams - CONTRACTOR <chas@cmf.nrl.navy.mil>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Pull libata fixes from Tejun Heo:
 "Nothing drastic but pushing out early due to build breakage in the new
  tegra platform.

  Additionally:

   - M550 tagged trim blacklist pattern is widened so that it matches
     the new 1TB model

   - three controller specific fixes"

* 'for-3.17-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/libata:
  libata: widen Crucial M550 blacklist matching
  pata_scc: propagate return value of scc_wait_after_reset
  ata: ahci_tegra: Change include to fix compilation
  pata_samsung_cf: change ret type to signed
  ahci_xgene: Removing NCQ support from the APM X-Gene SoC AHCI SATA Host Controller driver.

Pull HID fixes from Jiri Kosina:

 - fixes for a couple potential memory corruption problems (the HW would
   have to be manufactured to be deliberately evil to trigger those)
   found by Ben Hawkes
 - fix for potential infinite loop when using sysfs interface of
   logitech driver, from Simon Wood
 - a couple more simple driver fixes

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/hid:
  HID: fix a couple of off-by-ones
  HID: logitech: perform bounds checking on device_id early enough
  HID: logitech: fix bounds checking on LED report size
  HID: logitech: Prevent possibility of infinite loop when using /sys interface
  HID: rmi: print an error if F11 is not found instead of stopping the device
  HID: hid-sensor-hub: use devm_ functions consistently
  HID: huion: Use allocated buffer for DMA
  HID: huion: Fail on parameter retrieval errors

Pull sound fixes from Takashi Iwai:
 "A bunch of ASoC fixes with a few HD-audio fixes in this pull request.

  All fairly small, boring and device-specific fixes, in addition to
  MAINTAINERS update for better reviewing"

* tag 'sound-3.17-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound:
  ALSA: hda/hdmi - apply Valleyview fix-ups to Cherryview display codec
  ALSA: hda/hdmi - set depop_delay for haswell plus
  ALSA: hda - restore the gpio led after resume
  ALSA: hda/realtek - Avoid setting wrong COEF on ALC269 & co
  ASoC: pxa-ssp: drop SNDRV_PCM_FMTBIT_S24_LE
  ASoC: fsl-esai: Revert .xlate_tdm_slot_mask() support
  ASoC: mcasp: Fix implicit BLCK divider setting
  ASoC: arizona: Fix TDM slot length handling in arizona_hw_params
  ASoC: pcm512x: Correct Digital Playback control names
  ASoC: dapm: Fix uninitialized variable in snd_soc_dapm_get_enum_double()
  ASoC: Intel: Restore Baytrail ADSP streams only when ADSP was in reset
  ASoC: Intel: Wait Baytrail ADSP boot at resume_early stage
  ASoC: Intel: Merge Baytrail ADSP suspend_noirq into suspend_late
  MAINTAINERS: Add i.MX maintainers and paths to Freescale ASoC entry
  ASoC: Intel: Update Baytrail ADSP firmware name

Pull i2c fixes from Wolfram Sang:
 "Here is the fixup for the 'lowlight' of my last pull request.  I2C is
  not selected anymore by I2C_ACPI.  Instead, the code in question now
  depends on I2C=y.

  Also, Mika has agreed to support me and be the maintainer for I2C-ACPI
  related patches.  Finally, a new-ID-patch came along last week"

* 'i2c/for-next' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux:
  MAINTAINERS: add maintainer for ACPI parts of I2C
  i2c: i801: Add PCI ID for Intel Braswell
  i2c: rework kernel config I2C_ACPI

Pull ia64 update from Tony Luck:
 "Add memfd_create syscall to ia64"

* tag 'please-pull-memfd_create' of git://git.kernel.org/pub/scm/linux/kernel/git/aegl/linux:
  [IA64] Wire up memfd_create() system call

Pull microblaze update from Michal Simek:
 "Wire-up seccomp/getrandom/memfd_create syscalls"

* tag 'microblaze-3.17-rc2' of git://git.monstr.eu/linux-2.6-microblaze:
  microblaze: Wire-up memfd_create syscall
  microblaze: Wire-up getrandom syscall
  microblaze: Wire-up seccomp syscall

There are a few very theoretical off-by-one bugs in report descriptor size
checking when performing a pre-parsing fixup. Fix those.

Cc: stable@vger.kernel.org
Reported-by: NBen Hawkes <hawkes@google.com>
Reviewed-by: NBenjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: NJiri Kosina <jkosina@suse.cz>

device_index is a char type and the size of paired_dj_deivces is 7
elements, therefore proper bounds checking has to be applied to
device_index before it is used.

We are currently performing the bounds checking in
logi_dj_recv_add_djhid_device(), which is too late, as malicious device
could send REPORT_TYPE_NOTIF_DEVICE_UNPAIRED early enough and trigger the
problem in one of the report forwarding functions called from
logi_dj_raw_event().

Fix this by performing the check at the earliest possible ocasion in
logi_dj_raw_event().

Cc: stable@vger.kernel.org
Reported-by: NBen Hawkes <hawkes@google.com>
Reviewed-by: NBenjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: NJiri Kosina <jkosina@suse.cz>

The check on report size for REPORT_TYPE_LEDS in logi_dj_ll_raw_request()
is wrong; the current check doesn't make any sense -- the report allocated
by HID core in hid_hw_raw_request() can be much larger than
DJREPORT_SHORT_LENGTH, and currently logi_dj_ll_raw_request() doesn't
handle this properly at all.

Fix the check by actually trimming down the report size properly if it is
too large.

Cc: stable@vger.kernel.org
Reported-by: NBen Hawkes <hawkes@google.com>
Reviewed-by: NBenjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: NJiri Kosina <jkosina@suse.cz>

Once the CAN-bus is open and a packet is sent, the controller switches
into the PASSIVE state. Once the BUS is closed again it goes the back
err-warning. The TX error counter goes 0 -> 0x80 -> 0x7f.
This patch makes sure that the user learns about this state chang
(CAN_STATE_ERROR_WARNING => CAN_STATE_ERROR_PASSIVE)
Signed-off-by: NSebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: NMatthias Klein <matthias.klein@optimeas.de>
Signed-off-by: NMarc Kleine-Budde <mkl@pengutronix.de>