If firmware did not have any feature flags set the
var would be left with values found on the stack
(i.e. garbage) yielding print string like this:

  (...) features \xffffffa6m:^R\xfffffffbԂ\xffffffc4^E

Fixes: b27bc5a4 ("ath10k: dump fw features during probing")
Signed-off-by: NMichal Kazior <michal.kazior@tieto.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

This patch enables MU-MIMO transmit beamforming support
for QCA99X0 chipsets.
Signed-off-by: NVivek Natarajan <nataraja@qti.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

qca61x4 uses the vdev param as a sole sufficient configuration
for txbf while qca99x0 enables txbf during peer assoc by
combining the vdev param value with peer assoc's vht capabilities

This patch gets the appropriate txbf configuration scheme
before passing the wmi command to enable the same in the firmware.
Signed-off-by: NVivek Natarajan <nataraja@qti.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

Even though there's a WMI enum for fragmentation
threshold no known firmware actually implements
it. Moreover it is not possible to rely frame
fragmentation to mac80211 because firmware clears
the "more fragments" bit in frame control making
it impossible for remote devices to reassemble
frames.

Hence implement a dummy callback just to say
fragmentation isn't supported. This effectively
prevents mac80211 from doing frame fragmentation
in software.

This fixes Tx becoming broken after setting
fragmentation threshold.

Fixes: 1010ba4c ("ath10k: unregister and remove frag_threshold callback")
Signed-off-by: NMichal Kazior <michal.kazior@tieto.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

Commit 1010ba4c ("ath10k: unregister and
remove frag_threshold callback") didn't remove all
instances of (futile) fragmentation threshold
configuration. No known firmware supports the
parameter so don't even bother setting it.
Signed-off-by: NMichal Kazior <michal.kazior@tieto.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

Boot loader versions as backward compatible,
starting from v1
Signed-off-by: NVladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

Boot loader reports error starting from the struct v2.

Print error info before reset (power up state) in debug mode,
and print same info as error if target reset timed out.
Signed-off-by: NVladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

Support for the system suspend/resume.
In preparation for the run-time PM, implementation made
run-time PM friendly: common for system and run-time PM
code factored out as generic functions, albeit is_runtime
parameter value is always false currently.

For debug purposes, "PM" debug category introduced.

Policy: AP-like interface can't be suspended; otherwise
suspend is allowed. Hardware brought down if interface
was up. Connection, if existed, get lost.
Interface will be brought up upon resume if it was up
before suspend.
Signed-off-by: NVladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

Allow network stack part of Rx processing to run on separate core,
relaxing CPU utilization on the core used for Rx NAPI.

If RXHASH feature is enabled, the driver sets rxhash of each skb to 1
to enable RPS. The core for processing the rx skb is determined by RPS
mechanism according to rx_cpus bit mask which is configured at user level.
For processing skbs on different core from the core which processes
the interrupts, it is recommended not to enable core 0 in rx_cpus bit mask.
Signed-off-by: NVladimir Shulman <QCA_shulmanv@QCA.qualcomm.com>
Signed-off-by: NVladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

Replace macros like "R", "W", "S", "C", defined multiple times,
with inline functions "wil_[rwsc]".

Use "readl" and "writel" instead of "ioread32" and "iowrite32"
since it is granted that memory transactions are used,
not port ones like IN/OUT
Signed-off-by: NVladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

In the recent kernel versions, multiple MSI is not well supported.
In particular, it is not supported on x86 and ARM architectures.
Also, internal interrupt handling logic is simpler and
more effective when using single interrupt.

Remove support for 3 MSI, convert module parameter
"use_msi" from int with range [0,1,3] to boolean.
Signed-off-by: NVladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

Rx drops may be for 2 reasons: frame is old,
or it is duplicate. On the debugfs "stations" entry,
provide counters per reorder buffer for total
frames processed, drops for these 2 reasons.
Also add debug print for dropped frames.
Signed-off-by: NVladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

When printing error message, provide string describing IE kind.
Derive it from IE type
This allows removing of error messages printing
in callers
Signed-off-by: NVladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

sort overall IE's handling
prepare code (disabled for now) to add IEs for the beacon
Signed-off-by: NVladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

FW is allowed to generate WMI events that are not handled by this driver.
Treat such case as warning instead of error.
Signed-off-by: NDedy Lansky <qca_dlansky@qca.qualcomm.com>
Signed-off-by: NVladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

Check event length;
hex dump both Rx and Tx frames
Signed-off-by: NVladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

Driver report supported TSO (v4 & v6) and IP checksum offload
in addition to previously supported features. In data path
skbs are checked for non-zero gso_size, and when detected sent
to additional function for processing TSO SKBs. Since HW does not
fully support TSO, additional effort is required from the driver.
Driver partitions the data into mss sized descriptors which are
then DMAed to the HW.
Signed-off-by: NVladimir Shulman <QCA_shulmanv@QCA.qualcomm.com>
Signed-off-by: NVladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

When loading with debug_fw flag, do not bail out on
unknown chipId
Signed-off-by: NVladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

Use function wil_fw_error_recovery() instead of inline equivalent code
Signed-off-by: NVladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

Multiple del_station requests may be sent to the driver by the
supplicant when turning down AP. This may overflow mailbox
between the FW and ucode

Wait till disconnect of one STA completed before sending next command.
Signed-off-by: NVladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

linux/device.h should be included using <>, not ""
since it is not local include
Signed-off-by: NVladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

In the debugfs, there is "ulong" attribute printing.
It is used for bitmap printing, and more appropriate format
would be hexadecimal, not decimal.
Signed-off-by: NVladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

When performing Rx reordering, count skb's dropped
per reorder buffer; and print dropped packets count
on the "stations" debugfs entry
Signed-off-by: NVladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

There are 2 versions of boot loader struct: v0 and v1.
In the v1, boot loader build version added; as well as
RF status.

Support both versions.

Boot loader structure v1 has RF status; ignore RF error if firmware
not going to be loaded; driver can still be used to interact with the HW
Signed-off-by: NVladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

Initial QCA99X0 support has a known issue with TCP Tx throughput.
All other path such as UDP Tx/Rx and TCP Rx meet their expectation
(> 900Mbps), but TCP Tx marked as low as 5Mbps when single pair is
used on iperf.

The root cause is turned out because TSO flag is not initialized
properly so that firmware configures TSO in wrong way.
TSO flags in msdu extension descriptor is required to be reset
to indicate firmware there is no TSO is enabled, otherwise it
could act as TSO is enabled which causes huge throughput drop.

In fact, it's enough by resetting TSO flags only to prevent the
unexpected behavior, but initializing whole msdu ext. descriptor
will help to clear uncertainty of firmware could bring on as it
constantly updated.
Signed-off-by: NPeter Oh <poh@qca.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

Add vendor/device id of QCA99X0 V2.0 to pci id table and
QCA99X0_HW_2_0_CHIP_ID_REV to ath10k_pci_supp_chips[] for
QCA99X0 to get detected by the driver.

kvalo: now QCA99X0 family of chipsets is supported by ath10k.
Tested client, AP and monitor mode with QCA9990.
Signed-off-by: NVasanthakumar Thiagarajan <vthiagar@qti.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

When max client was set to 512 in qca99x0, there was host memory
alloc failure during wmi service ready event handling. This issue
got resolved now, increasing max client limit from 256 to 512.
Signed-off-by: NRaja Mani <rmani@qti.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

Host memory required for firmware is allocated while handling
wmi service ready event. Right now, wmi service ready is handled
in tasklet context and it calls dma_alloc_coherent() with atomic
flag (GFP_ATOMIC) to allocate memory in host needed for firmware.
The problem is, dma_alloc_coherent() with GFP_ATOMIC fails in
the platform (at least in AP platform) where it has less atomic
pool memory (< 2mb). QCA99X0 requires around 2 MB of host memory
for one card, having additional QCA99X0 card in the same platform
will require similarly amount of memory. So, it's not guaranteed that
all the platform will have enough atomic memory pool.

Fix this issue, by handling wmi service ready event in workqueue
context and calling dma_alloc_coherent() with GFP_KERNEL. mac80211 work
queue will not be ready at the time of handling wmi service ready.
So, it can't be used to handle wmi service ready. Also, register work
gets scheduled during insmod in existing ath10k_wq and waits for
wmi service ready to completed. Both workqueue can't be used for
this purpose. New auxiliary workqueue is added to handle wmi service
ready.
Signed-off-by: NRaja Mani <rmani@qti.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

This patch enables raw Rx/Tx encap mode to support software based
crypto engine. This patch introduces a new module param 'cryptmode'.

 cryptmode:

   0: Use hardware crypto engine globally with native Wi-Fi mode TX/RX
      encapsulation to the firmware. This is the default mode.
   1: Use sofware crypto engine globally with raw mode TX/RX
      encapsulation to the firmware.

Known limitation:
   A-MSDU must be disabled for RAW Tx encap mode to perform well when
   heavy traffic is applied.

Testing: (by Michal Kazior <michal.kazior@tieto.com>)

     a) Performance Testing

      cryptmode=1
       ap=qca988x sta=killer1525
        killer1525  ->  qca988x     194.496 mbps [tcp1 ip4]
        killer1525  ->  qca988x     238.309 mbps [tcp5 ip4]
        killer1525  ->  qca988x     266.958 mbps [udp1 ip4]
        killer1525  ->  qca988x     477.468 mbps [udp5 ip4]
        qca988x     ->  killer1525  301.378 mbps [tcp1 ip4]
        qca988x     ->  killer1525  297.949 mbps [tcp5 ip4]
        qca988x     ->  killer1525  331.351 mbps [udp1 ip4]
        qca988x     ->  killer1525  371.528 mbps [udp5 ip4]
       ap=killer1525 sta=qca988x
        qca988x     ->  killer1525  331.447 mbps [tcp1 ip4]
        qca988x     ->  killer1525  328.783 mbps [tcp5 ip4]
        qca988x     ->  killer1525  375.309 mbps [udp1 ip4]
        qca988x     ->  killer1525  403.379 mbps [udp5 ip4]
        killer1525  ->  qca988x     203.689 mbps [tcp1 ip4]
        killer1525  ->  qca988x     222.339 mbps [tcp5 ip4]
        killer1525  ->  qca988x     264.199 mbps [udp1 ip4]
        killer1525  ->  qca988x     479.371 mbps [udp5 ip4]

      Note:
       - only open network tested for RAW vs nwifi performance comparison
       - killer1525 (qca6174 hw2.2) is 2x2 device (hence max 866mbps)
       - used iperf
       - OTA, devices a few cm apart from each other, no shielding
       - tcpX/udpX, X - means number of threads used

      Overview:
       - relative Tx performance drop is seen but is within reasonable and
         expected threshold (A-MSDU must be disabled with RAW Tx)

     b) Connectivity Testing

      cryptmode=1
       ap=iwl6205 sta1=qca988x crypto=open     topology-1ap1sta          OK
       ap=iwl6205 sta1=qca988x crypto=wep1     topology-1ap1sta          OK
       ap=iwl6205 sta1=qca988x crypto=wpa      topology-1ap1sta          OK
       ap=iwl6205 sta1=qca988x crypto=wpa-ccmp topology-1ap1sta          OK
       ap=qca988x sta1=iwl6205 crypto=open     topology-1ap1sta          OK
       ap=qca988x sta1=iwl6205 crypto=wep1     topology-1ap1sta          OK
       ap=qca988x sta1=iwl6205 crypto=wpa      topology-1ap1sta          OK
       ap=qca988x sta1=iwl6205 crypto=wpa-ccmp topology-1ap1sta          OK
       ap=iwl6205 sta1=qca988x crypto=open     topology-1ap1sta2br       OK
       ap=iwl6205 sta1=qca988x crypto=wep1     topology-1ap1sta2br       OK
       ap=iwl6205 sta1=qca988x crypto=wpa      topology-1ap1sta2br       OK
       ap=iwl6205 sta1=qca988x crypto=wpa-ccmp topology-1ap1sta2br       OK
       ap=qca988x sta1=iwl6205 crypto=open     topology-1ap1sta2br       OK
       ap=qca988x sta1=iwl6205 crypto=wep1     topology-1ap1sta2br       OK
       ap=qca988x sta1=iwl6205 crypto=wpa      topology-1ap1sta2br       OK
       ap=qca988x sta1=iwl6205 crypto=wpa-ccmp topology-1ap1sta2br       OK
       ap=iwl6205 sta1=qca988x crypto=open     topology-1ap1sta2br1vlan  OK
       ap=iwl6205 sta1=qca988x crypto=wep1     topology-1ap1sta2br1vlan  OK
       ap=iwl6205 sta1=qca988x crypto=wpa      topology-1ap1sta2br1vlan  OK
       ap=iwl6205 sta1=qca988x crypto=wpa-ccmp topology-1ap1sta2br1vlan  OK
       ap=qca988x sta1=iwl6205 crypto=open     topology-1ap1sta2br1vlan  OK
       ap=qca988x sta1=iwl6205 crypto=wep1     topology-1ap1sta2br1vlan  OK
       ap=qca988x sta1=iwl6205 crypto=wpa      topology-1ap1sta2br1vlan  OK
       ap=qca988x sta1=iwl6205 crypto=wpa-ccmp topology-1ap1sta2br1vlan  OK

      Note:
       - each test takes all possible endpoint pairs and pings
       - each pair-ping flushes arp table
       - ip6 is used

     c) Testbed Topology:

      1ap1sta:
        [ap] ---- [sta]

        endpoints: ap, sta

      1ap1sta2br:
        [veth0] [ap] ---- [sta] [veth2]
           |     |          |     |
        [veth1]  |          \   [veth3]
            \   /            \  /
            [br0]            [br1]

        endpoints: veth0, veth2, br0, br1
        note: STA works in 4addr mode, AP has wds_sta=1

      1ap1sta2br1vlan:
        [veth0] [ap] ---- [sta] [veth2]
           |     |          |     |
        [veth1]  |          \   [veth3]
            \   /            \  /
          [br0]              [br1]
            |                  |
          [vlan0_id2]        [vlan1_id2]

        endpoints: vlan0_id2, vlan1_id2
        note: STA works in 4addr mode, AP has wds_sta=1

Credits:

    Thanks to Michal Kazior <michal.kazior@tieto.com> who helped find the
    amsdu issue, contributed a workaround (already squashed into this
    patch), and contributed the throughput and connectivity tests results.
Signed-off-by: NDavid Liu <cfliu.tw@gmail.com>
Signed-off-by: NMichal Kazior <michal.kazior@tieto.com>
Tested-by: NMichal Kazior <michal.kazior@tieto.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

During tx completion, tx_lock is held for longer than required, preventing
efficient refill of htt->pending_tx. Refactor the code so that only MSDU
related operations are protected by the lock.

Improves downstream performance on a dual-core ARM Freescale LS1024A
(f.k.a. Mindspeed Comcerto 2000) AP with a 3x3 client from 495 to 580 Mbps.
Other CPU bound multicore systems may also benefit.
Signed-off-by: NDenton Gentry <dgentry@google.com>
Signed-off-by: NAvery Pennarun <apenwarr@google.com>
[mfaltesek@google.com: removed conflicting code for tracking msdu_ids.]
Signed-off-by: NMarty Faltesek <mfaltesek@google.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

When using DFS channels on Ath10k, kernel log has repeated warning message
'failed to process fft: -22' typically under medium/heavy traffic.

This patch switches the warnings to driver debug (WMI events) mode only
thus reducing log file noise.

DFS and spectral scan share underlying HW mechanisms and enabling one
(DFS) enables the other (spectral scan) as far as event reporting from
firmware to driver is concerned. Spectral scan events take no part in
processing of DFS radar pulses which are delivered as distinct events,
so the fft (spectral event) warning is harmless and DFS interference
detection/protection still occurs.

Symptoms seen & fix tested in both debug & non-debug modes on TP-Link
Archer C7 v2 platform.
Signed-off-by: NKevin Darbyshire-Bryant <kevin@darbyshire-bryant.me.uk>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

This fixes two misspellings of "distribution" in a comment.
Signed-off-by: NNik Nyby <nikolas@gnu.org>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

HTT_H2T_MSG_TYPE_MGMT_TX msg in 10.4 firmware carries additional
4 byte in htt_mgmt_tx_desc where it tells to firmware that at what
rate mgmt frame has to go out in the air. It's an optional parameter,
setting this field to zero will force firmware to choose auto rate
and send the frame out.

Those 4 byte info is missed out in the current code and 10.4 firmware
ended up reading some junk in those 4 byte and sometime malfunctioning.

Fix it by adding 4 byte in struct htt_mgmt_tx_desc. Non 10.4 firmware
will not process those four byte. So, adding 4 byte at the end of
struct htt_mgmt_tx_desc will not create any impact on other chipset.
Signed-off-by: NRaja Mani <rmani@qti.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

The patch adds support to offload TCP/UDP checksum
calculations for QCA99x0.
Signed-off-by: NManikanta Pubbisetty <c_mpubbi@qti.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

chandef is initialized with NULL and on the very next line, we are using it to
get channel, which is not correct. Channel should be initialized after
obtaining chandef.

Found by cppcheck:

ath/ath10k/mac.c:839]: (error) Possible null pointer dereference: chandef
Signed-off-by: NManinder Singh <maninder1.s@samsung.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

QCA99X0 chip has an extra 4 bytes in rx_msdu_start,
20 bytes in rx_msdu_end and 20 bytes in rx_ppdu_end structure
which are used in htt_rx_desc and HTT Rx ring offset setup.
This is necessary for correct Rx for QCA99X0 or Rx descriptors
will be overwritten and corrupted.

With this patch QCA988X and QCA6174 will have extra 44 bytes
padding in Rx descriptor layout which is harmless.
Signed-off-by: NPeter Oh <poh@qca.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

rx_ppdu_end_common structure is valid for both of qca998x and
qca6174, but not for qca99x0 since it has new additional members.
Hence update the common structure to cover qca99x0 as well.
Signed-off-by: NPeter Oh <poh@qca.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

Since QCA99X0 uses fragmentation descriptor differently from
other ones on tx path, we need to handle it separately.

QCA99X0 is using 48 bits for address and 16 bits for length
out of 2 dword and each values have to be programmed by frag
desc base addr + msdu id, so that hardware can retrieve
corresponding frag data.
Signed-off-by: NPeter Oh <poh@qca.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

It is observed that during cold reset pcie access right
after a write operation to SOC_GLOBAL_RESET_ADDRESS causes
Data Bus Error and system hard lockup. The reason
for bus error is that pcie needs some time to get
back to stable state for any transaction during cold reset. Add
delay of 20 msecs after write of SOC_GLOBAL_RESET_ADDRESS
to fix this issue. This patch is tested on QCA988X. This is
also tested on QCA99X0 which is WIP.
Signed-off-by: NVasanthakumar Thiagarajan <vthiagar@qti.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

Major changes in ath10k:

* enable VHT for IBSS
* initial work to support qca99x0 and the corresponding 10.4 firmware branch