The RTC is sitting on the I2C2 bus at address 0x68. RTC interrupt signal
is connected to the IPIC's EXT2 interrupt line, the line is shared with
Vitesse 8201 Ethernet PHY.
Signed-off-by: NAnton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: NKumar Gala <galak@kernel.crashing.org>

MCU is an external Freescale MC9S08QG8 microcontroller, mainly used to
provide soft power-off function, but also exports two GPIOs (wired to
the LEDs and also available from the external headers).

Added the MCU on mpc8349emitx, mpc837xrdb and mpc8315erdb boards.
Signed-off-by: NAnton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: NKumar Gala <galak@kernel.crashing.org>

Change the top-level #address-cells and #size-cells to <2> so the
mpc8572ds.dts is easier to deal with both a true 32-bit physical
or 36-bit physical address space.
Signed-off-by: NKumar Gala <galak@kernel.crashing.org>

We don't want to encourage the bogus device_type usage.

The device type isn't used in the code, so we can simply remove it from
the documentation and dts files.

Boards should specify proper compatible entries instead.
Signed-off-by: NAnton Vorontsov <avorontsov@ru.mvista.com>
Acked-by: NDavid Gibson <david@gibson.dropbear.id.au>
Signed-off-by: NKumar Gala <galak@kernel.crashing.org>

Signed-off-by: NEd Swarthout <Ed.Swarthout@freescale.com>
Signed-off-by: NKumar Gala <galak@kernel.crashing.org>

Signed-off-by: NJason Jin <Jason.jin@freescale.com>
Signed-off-by: NKumar Gala <galak@kernel.crashing.org>

These functions should have been static, and inspection shows they
are no longer used.   (We used to parse mem= but we now defer that
to early_param).
Signed-off-by: NMilton Miller <miltonm@bga.com>
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>

Commit 9b09c6d9 ("powerpc: Change the
default link address for pSeries zImage kernels") changed the
real-base value in the CHRP note added by addnote to the zImage from
12MB to 32MB.  It turns out that this causes unnecessary extra reboots
on old 32-bit CHRP machines.  This therefore adds a -r flag to addnote
to allow us to specify what real-base value it should put in the CHRP
note, and adjusts the wrapper script to pass -r c00000 to addnote when
making a zImage for a CHRP machine.  Also, CHRP machines ignore the
RPA note, so we don't need to arrange for it to be the same as the
kernel's.
Signed-off-by: NPaul Mackerras <paulus@samba.org>
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>

numa_enforce_memory_limit tried to be smart and only call lmb_end_of_DRAM
when a memory limit was set via mem= on the command line.  However,
the early boot code will also limit memory added to the lmb system
when iommu=off is specified.  When this happens, the page allocator
is given pages not in the linear mapping and this results in a fatal
data reference to the unmapped page.
Signed-off-by: NMilton Miller <miltonm@bga.com>
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>

We used to assume that even numbered threads were the primary
threads, ie those that would be listed and started as a cpu from
open firmware.  Replace a left over is even (% 2) check with a check
for it being a primary thread and update the comments.

Tested with a debug print on pseries, identical code found for cell.
Signed-off-by: NMilton Miller <miltonm@bga.com>
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>

64 bit powerpc requires the kexec user space tools avoid overwriting
the static kernel image and translation hash table when choosing
where to put memory image data because it copies the data into place
using the kernels virtual memory system.  Kexec userspace determines
these and other areas blocked by reading properties the kernel adds,
but does not filter these properties when creating the device tree
for the next kernel.

When the second kernel tries to add its values for these properties,
the export via /proc/device-tree is hidden by the pre-existing but
stale values from the flat tree.  Kexec userspace reads the old
property, allocates the new kernel at the old kernel's end, and
gets rejected by the overlap check.

Search and remove these stale properties before adding the new values.
Signed-off-by: NMilton Miller <miltonm@bga.com>
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>

There are no users of PPC_MERGE in tree so we can get rid of it.
It was a hold over from the arch/ppc days.
Signed-off-by: NKumar Gala <galak@kernel.crashing.org>
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>

There are two issues when we enable CONFIG_RELOCATABLE.  The first is due
to the fact that phys_addr_t is now defined in linux/types.h.  The second
is due to the fact that the DMA code changes expose memstart_addr to
prom_init.c
Signed-off-by: NKumar Gala <galak@kernel.crashing.org>
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>

This target is needed to build cuImages with an embedded ramdisk image.
Signed-off-by: NGrant Likely <grant.likely@secretlab.ca>
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>

I noticed, when trying to use, e.g.,
node = find_node_by_prop_value(prev, "booleanprop", "", 0))
to search for all nodes with a certain boolean property, that memcmp()
returns garbage when comparing zero bytes.  It should return zero.
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>

Adjust amount to reserve based on previous nodes for reserves spanning
multiple nodes. Check if the node active range is empty before attempting
to pass the reserve to bootmem.  In practice the range shouldn't be empty,
but to be sure we check.
Signed-off-by: NJon Tollefson <kniht@linux.vnet.ibm.com>
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>

The issue is the SPU code is not holding the kernel mutex lock while
adding samples to the kernel buffer.

This patch creates per SPU buffers to hold the data.  Data
is added to the buffers from in interrupt context.  The data
is periodically pushed to the kernel buffer via a new Oprofile
function oprofile_put_buff(). The oprofile_put_buff() function
is called via a work queue enabling the funtion to acquire the
mutex lock.

The existing user controls for adjusting the per CPU buffer
size is used to control the size of the per SPU buffers.
Similarly, overflows of the SPU buffers are reported by
incrementing the per CPU buffer stats.  This eliminates the
need to have architecture specific controls for the per SPU
buffers which is not acceptable to the OProfile user tool
maintainer.

The export of the oprofile add_event_entry() is removed as it
is no longer needed given this patch.

Note, this patch has not addressed the issue of indexing arrays
by the spu number.  This still needs to be fixed as the spu
numbering is not guarenteed to be 0 to max_num_spus-1.
Signed-off-by: NCarl Love <carll@us.ibm.com>
Signed-off-by: NMaynard Johnson <maynardj@us.ibm.com>
Signed-off-by: NArnd Bergmann <arnd@arndb.de>
Acked-by: NAcked-by: Robert Richter <robert.richter@amd.com>
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>

"unsigned int" speed cannot be negative, it's thus pointless
to test if it is.
Signed-off-by: NRoel Kluin <roel.kluin@gmail.com>
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>

The pfn of the memory to be removed should be validated prior to
attempting to remove the memory.  In cases where the probe of a
memory section fails during hotplug add, the pfn for the lmb may
not be valid.
Signed-off-by: NBadari Pulavarty <pbadari@us.ibm.com>
Signed-off-by: NNathan Fontenot <nfont@austin.ibm.com>
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>

If the vmlinux binary in memory is larger than 4 MiB than it collides
with the initial boot code which is linked at 4 MiB in case of cuBoot.
If the the uncompressed image size (on disk size) is less than 4 MiB
then it would fit. The difference between those two sizes is the bss
section. In cuBoot we have the dtb embedded right after the data
section so it is very likely that the reset of the bss section (in
kernel's start up code) will overwrite the dtb blob. Therefore we
reallocate the dtb. Something similar is allready done to the initrd.
Signed-off-by: NSebastian Andrzej Siewior <bigeasy@linutronix.de>
Acked-by: NDavid Gibson <david@gibson.dropbear.id.au>
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>

This patch adds a comment to clarify why atomic_dec_if_positive is being used
to decrement gang's aff_sched_count on SPU context unbind.
Signed-off-by: NAndre Detsch <adetsch@br.ibm.com>
Signed-off-by: NJeremy Kerr <jk@ozlabs.org>

This patch improves redability of the code responsible for trying to find
a node with enough SPUs not committed to other affinity gangs.

An additional check is also added, to avoid taking into account gangs that
have no SPU affinity.
Signed-off-by: NAndre Detsch <adetsch@br.ibm.com>
Signed-off-by: NJeremy Kerr <jk@ozlabs.org>

No need to zero the entire buffer, just the head and tail indices.
Signed-off-by: NJeremy Kerr <jk@ozlabs.org>

With most file readers (eg cat, dd), reading a context's regs file will
result in two reads: the first to read the data, and the second to
return EOF. Because each read performs a spu_acquire_saved, we end up
descheduling and re-scheduling the context twice.

This change does a simple check to see if we'd return EOF before
calling spu_acquire_saved(), saving the extra schedule operation.
Signed-off-by: NJeremy Kerr <jk@ozlabs.org>

Currently, read() on the sputrace log will block until the read buffer
is full. This makes it difficult to retrieve the end of the buffer, as
the user will need to read with the right-sized buffer.

In a similar method as 91553a1b5e0df006a3573a88d98ee7cd48a3818a, this
change makes the switch_log return if there has already been data
read.
Signed-off-by: NJeremy Kerr <jk@ozlabs.org>

Currently, we use ctx->mapping_lock and ctx->switch_log->lock for the
context switch log. The mapping lock only prevents concurrent open()s,
so we require the switch_lock->lock for reads.

Since writes to the switch log buffer occur on context switches, we're
better off synchronising with the state_mutex, which is held during a
switch. Since we're serialised througout the buffer reads and writes,
we can use the state mutex to protect open and release too, and
can now kfree() the log buffer on release. This allows us to perform
the switch log notify without taking any extra locks.

Because the buffer is only present while the file is open, we can use
it to prevent multiple simultaneous openers.
Signed-off-by: NJeremy Kerr <jk@ozlabs.org>

Currently, read() on the sputrace buffer will only return data when
the user buffer is exhausted. This may mean that we never see the
end of the event log, unless we read() with exactly the right-sized
buffer.

This change makes sputrace_read not block if we have data ready to
return.
Signed-off-by: NJeremy Kerr <jk@ozlabs.org>

Currently, sputrace will start logging to the event buffer before the
log buffer has been open()ed. This results in a heap of "lost samples"
warnings if the sputrace file hasn't yet been opened.

Since the buffer is reset on open() anyway, there's no need to enable
logging when no-one has opened the log.

Because open clears the log, make it return EBUSY for mutliple open
calls.
Signed-off-by: NJeremy Kerr <jk@ozlabs.org>

This patch adds support for the GPIO functions of PPC40x and PPC44x
SOCs.
Signed-off-by: NSteve Falco <sfalco@harris.com>
Acked-by: NStefan Roese <sr@denx.de>
Acked-by: NSean MacLennan <smaclennan@pikatech.com>
Signed-off-by: NJosh Boyer <jwboyer@linux.vnet.ibm.com>

Adds support for a HCU4 PPC405GPr based board from Netstal Maschinen AG.
Signed-off-by: NNiklaus Giger <niklaus.giger@member.fsf.org>
Signed-off-by: NJosh Boyer <jwboyer@linux.vnet.ibm.com>

Add simple defconfig for the AMCC PowerPC 405EZ Acadia evaluation board
Signed-off-by: NJosh Boyer <jwboyer@linux.vnet.ibm.com>

This adds a cuboot wrapper for the AMCC PowerPC 405EZ Acadia board.  The
clocking code is derived from U-Boot, originally written by Stefan Roese.
Signed-off-by: NJosh Boyer <jwboyer@linux.ibm.com>

This adds a common board file for almost all of the "simple" PowerPC 40x
boards that exist today.  This is intended to be a single place to add
support for boards that do not differ in platform support from most of the
evaluation boards that are used as reference platforms.  Boards that have
specific requirements or custom hardware setup should still have their own
board.c file.

The first board ported to this is the AMCC PowerPC 405EZ Acadia board.
Signed-off-by: NJosh Boyer <jwboyer@linux.vnet.ibm.com>

This adds the AMCC PowerPC 405EZ chip to the cputable
Signed-off-by: NJosh Boyer <jwboyer@linux.vnet.ibm.com>

Add the base DTS for the AMCC PowerPC 405EZ Acadia evalution board.
In addition to some of the normal PPC 40x peripherals, the Acadia
board has:
- 64 MiB PSRAM
- NOR and NAND flash
- Two USB 1.1 host ports
- Two CAN 2.0 ports
- ADC and DAC connectors
- LCD display

This adds the basic platform support to build from.
Signed-off-by: NJosh Boyer <jwboyer@linux.vnet.ibm.com>

MPC5200 needs to have pipelining disabled for ATA to work. MPC5200B does not.
So, for the latter, don't touch the original setting from the bootloader.
Signed-off-by: NWolfram Sang <w.sang@pengutronix.de>
Signed-off-by: NGrant Likely <grant.likely@secretlab.ca>

Current device trees do not have the device_type = soc property set
anymore.  Fix up the cuImage bootwrapper fragment to still find the IMMR
nodes.
Signed-off-by: NGrant Likely <grant.likely@secretlab.ca>

Signed-off-by: NShinya Kuribayashi <skuribay@ruby.dti.ne.jp>
Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

Signed-off-by: NThomas Bogendoerfer <tsbogend@alpha.franken.de>
Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

This patchset removes some dead code and creates a platform device
for the RTC class driver.
Signed-off-by: NThomas Bogendoerfer <tsbogend@alpha.franken.de>
Signed-off-by: NRalf Baechle <ralf@linux-mips.org>