On runtime pm resume, we need to download the firmware, also on
suspend we need to ensure all the interrupts from controller and
DSP are disabled.

Also since we download the firmware on resume, we don't need to do
so on init, so remove that bit
Signed-off-by: NJeeja KP <jeeja.kp@intel.com>
Signed-off-by: NVinod Koul <vinod.koul@intel.com>
Signed-off-by: NMark Brown <broonie@kernel.org>

Like we have in legacy mode HDA driver, we need to check the
status bit and handle interrupt only when it is not zero or all
bits set.  We typically see the status as all 1's when controller
resumes from suspend, So add the check here as well and don't
handle for these cases.
Signed-off-by: NJeeja KP <jeeja.kp@intel.com>
Signed-off-by: NVinod Koul <vinod.koul@intel.com>
Signed-off-by: NMark Brown <broonie@kernel.org>

Skylake driver will set the SPA bit to 0 to turn off the DSP core.
Driver will poll the Current Power Active (CPA) bit to match the
Set Power Active (SPA) bit value. When CPA bit matches the value
of SPA bit, the achieved power state has reached.

In case of DSP power down, register that was polled is SPA
instead of CPA. This patch corrects the register to be polled
in case of DSP power down.
Signed-off-by: NJeeja KP <jeeja.kp@intel.com>
Signed-off-by: NVinod Koul <vinod.koul@intel.com>
Signed-off-by: NMark Brown <broonie@kernel.org>

dev_info is too noisy for tplg wiget loading, so move it to
debug level
Signed-off-by: NVinod Koul <vinod.koul@intel.com>
Signed-off-by: NMark Brown <broonie@kernel.org>

Load and Initialize Non HDA Link Table in Skylake driver
to get platform configuration.
Signed-off-by: NJeeja KP <jeeja.kp@intel.com>
Signed-off-by: NSubhransu S. Prusty <subhransu.s.prusty@intel.com>
Signed-off-by: NVinod Koul <vinod.koul@intel.com>
Signed-off-by: NMark Brown <broonie@kernel.org>

If processing pipe capability is supported, add DSP support.
Adds initialization/free/suspend/resume DSP functionality.
Signed-off-by: NJeeja KP <jeeja.kp@intel.com>
Signed-off-by: NSubhransu S. Prusty <subhransu.s.prusty@intel.com>
Signed-off-by: NVinod Koul <vinod.koul@intel.com>
Signed-off-by: NMark Brown <broonie@kernel.org>

Initialize and creates DSP controls if processing pipe capability
is supported by HW. Updates the dma_id, hw_params to module param
to be used when DSP module has to be configured.
Signed-off-by: NJeeja KP <jeeja.kp@intel.com>
Signed-off-by: NSubhransu S. Prusty <subhransu.s.prusty@intel.com>
Signed-off-by: NVinod Koul <vinod.koul@intel.com>
Signed-off-by: NMark Brown <broonie@kernel.org>

The SKL driver does not code DSP topology in driver. It uses the
newly added ASoC topology core to parse the topology information
(controls, widgets and map) from topology binary.
Each topology element passed private data which contains
information that driver used to identify the module instance
within firmware and send IPCs for that module to DSP firmware
along with parameters.
This patch adds init routine to invoke topology load and callback
for topology creation.
Signed-off-by: NJeeja KP <jeeja.kp@intel.com>
Signed-off-by: NSubhransu S. Prusty <subhransu.s.prusty@intel.com>
Signed-off-by: NVinod Koul <vinod.koul@intel.com>
Signed-off-by: NMark Brown <broonie@kernel.org>

For FE and BE, the PCM parameters come from FE and BE hw_params
values passed. For a FE we convert the FE params to DSP expected
module format and pass to DSP. For a BE we need to find the
gateway settings (i2s/PDM) to be applied. These are queried from
NHLT table and applied.

Further for BE based on direction the settings are applied as
either source or destination parameters.

These helpers here allow the format to be calculated and queried
as per firmware format.
Signed-off-by: NJeeja KP <jeeja.kp@intel.com>
Signed-off-by: NSubhransu S. Prusty <subhransu.s.prusty@intel.com>
Signed-off-by: NVinod Koul <vinod.koul@intel.com>
Signed-off-by: NMark Brown <broonie@kernel.org>

The Skylake driver topology model tries to model the firmware
rule for pipeline and module creation.
The creation rule is:
 - Create Pipe
 - Add modules to Pipe
 - Connect the modules (bind)
 - Start the pipes

Similarly destroy rule is:
 - Stop the pipe
 - Disconnect it (unbind)
 - Delete the pipe

In driver we use Mixer, as there will always be ONE mixer in a
pipeline to model a pipe. The modules in pipe are modelled as PGA
widgets.  The DAPM sequencing rules (mixer and then PGA) are used
to create the sequence DSP expects as depicted above, and then
widget handlers for PMU and PMD events help in that.

This patch adds widget event handlers for PRE/POST PMU and
PRE/POST PMD event for mixer and pga modules.  These event
handlers invoke pipeline creation, destroy, module creation,
module bind, unbind and pipeline bind unbind

Event handler sequencing is implement to target the DSP FW
sequence expectations to enable path from source to sink pipe for
Playback/Capture.
Signed-off-by: NJeeja KP <jeeja.kp@intel.com>
Signed-off-by: NHardik T Shah <hardik.t.shah@intel.com>
Signed-off-by: NSubhransu S. Prusty <subhransu.s.prusty@intel.com>
Signed-off-by: NVinod Koul <vinod.koul@intel.com>
Signed-off-by: NMark Brown <broonie@kernel.org>

To configure a module, driver needs to send input and output PCM
params for a module in DSP. The FE PCM params come from hw_params
ie from user, for a BE they also come from hw_params but from
BE-link fixups.
So based on PCM params required driver has to find a converter
module (src/updown/format) and then do the conversion and
calculate PCM params in these pipelines In this patch we add the
helper modules which allow driver to do these calculations.
Signed-off-by: NHardik T Shah <hardik.t.shah@intel.com>
Signed-off-by: NJeeja KP <jeeja.kp@intel.com>
Signed-off-by: NSubhransu S. Prusty <subhransu.s.prusty@intel.com>
Signed-off-by: NVinod Koul <vinod.koul@intel.com>
Signed-off-by: NMark Brown <broonie@kernel.org>

SKL driver needs to instantiate pipelines and modules in the DSP.
The topology in the DSP is modelled as DAPM graph with a PGA
representing a module instance and mixer representing a pipeline
for a group of modules along with the mixer itself.

Here we start adding building block for handling these. We add
resource checks (memory/compute) for pipelines, find the modules
in a pipeline, init modules in a pipe and lastly bind/unbind
modules in a pipe These will be used by pipe event handlers in
subsequent patches
Signed-off-by: NJeeja KP <jeeja.kp@intel.com>
Signed-off-by: NSubhransu S. Prusty <subhransu.s.prusty@intel.com>
Signed-off-by: NVinod Koul <vinod.koul@intel.com>
Signed-off-by: NMark Brown <broonie@kernel.org>

Instead of hardconding a platform data for dw_dmac let's use it's own
autoconfiguration feature. Thus, remove hardcoded values.
Acked-by: NLiam Girdwood <liam.r.girdwood@linux.intel.com>
Cc: Mark Brown <broonie@kernel.org>
Signed-off-by: NAndy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: NMark Brown <broonie@kernel.org>

We need to create CPU DAI for each endpoint instance. For this we
should have one DMIC DAI, one HDA DAI and SSP DAI.  Thus, DMIC23,
HDA-SPK/AMIC was not required so this patch removes them
Signed-off-by: NJeeja KP <jeeja.kp@intel.com>
Signed-off-by: NSubhransu S. Prusty <subhransu.s.prusty@intel.com>
Signed-off-by: NVinod Koul <vinod.koul@intel.com>
Signed-off-by: NMark Brown <broonie@kernel.org>

The function get_current_pipe_id() was not being used.
Signed-off-by: NSudip Mukherjee <sudip@vectorindia.org>
Signed-off-by: NMark Brown <broonie@kernel.org>

Signed-off-by: NAxel Lin <axel.lin@ingics.com>
Signed-off-by: NMark Brown <broonie@kernel.org>

Set the card owner field to prevent the module from being removed from
underneath its users.
Signed-off-by: NAxel Lin <axel.lin@ingics.com>
Signed-off-by: NMark Brown <broonie@kernel.org>

pm_runtime_get_sync() increments the runtime PM usage counter even the
call returns an error code. Thus a pairing decrement is needed on the
error handling path to keep the counter balanced.
Signed-off-by: NJunjie Mao <junjie.mao@enight.me>
Signed-off-by: NMark Brown <broonie@kernel.org>

To manage DSP we need to create processing pipeline and on cleanup destroy
them. So we add create and destroy routines for pipelines The pipelines need
to to be executed so we add pipeline run and stop routines
All these send required IPCs to DSP using IPC routines added earlier
Signed-off-by: NJeeja KP <jeeja.kp@intel.com>
Signed-off-by: NVinod Koul <vinod.koul@intel.com>
Signed-off-by: NMark Brown <broonie@kernel.org>

A module needs to be instantiated and then connected with other modules. On
cleanup we need to disconnect the module.
This is achieved by helpers module init, bind and unbind which are added
here
Signed-off-by: NJeeja KP <jeeja.kp@intel.com>
Signed-off-by: NVinod Koul <vinod.koul@intel.com>
Signed-off-by: NMark Brown <broonie@kernel.org>

SRC and converter modules are required to do frequency and channel
conversion in DSP. Both take base module configuration and additional SRC
and converter parameters. The helpers here are added to calculate the values
for these modules
Signed-off-by: NHardik T Shah <hardik.t.shah@intel.com>
Signed-off-by: NJeeja KP <jeeja.kp@intel.com>
Signed-off-by: NVinod Koul <vinod.koul@intel.com>
Signed-off-by: NMark Brown <broonie@kernel.org>

This adds helper functions to calculate parameters required for base module
format and copier module. A generic module is modelled by base module.
Copier module is responsible for getting/sending data to FE (host DMAs) and
BE (link HDA DMA, SSP, PDM)
This also ads module pin management helpers which help in finding pins to
use or freeing them up
Signed-off-by: NJeeja KP <jeeja.kp@intel.com>
Signed-off-by: NVinod Koul <vinod.koul@intel.com>
Signed-off-by: NMark Brown <broonie@kernel.org>

Instead of defining own acpi header, use the available acpi
header defined in acpi framework.
Signed-off-by: NJeeja KP <jeeja.kp@intel.com>
Signed-off-by: NVinod Koul <vinod.koul@intel.com>
Signed-off-by: NMark Brown <broonie@kernel.org>

Sampling rate type needs to be u32 instead of u8, nhlt wav format
description expected u32 for rate, passing u8 will fetch NULL
config in skl_get_ep_blob().
Signed-off-by: NJeeja KP <jeeja.kp@intel.com>
Signed-off-by: NVinod Koul <vinod.koul@intel.com>
Signed-off-by: NMark Brown <broonie@kernel.org>

The patch was generated using fixed coccinelle semantic patch
scripts/coccinelle/api/memdup.cocci [1].

[1]: http://permalink.gmane.org/gmane.linux.kernel/2014320Signed-off-by: NAndrzej Hajda <a.hajda@samsung.com>
Signed-off-by: NMark Brown <broonie@kernel.org>

Add initialization for sst_byt.dev at init stage, which fix the
'NULL device *' warning issues.
Signed-off-by: NJie Yang <yang.jie@intel.com>
Signed-off-by: NMark Brown <broonie@kernel.org>

Add initialization for sst_hsw.dev at init stage, which fix the
'NULL device *' warning issues.
Signed-off-by: NJie Yang <yang.jie@intel.com>
Signed-off-by: NMark Brown <broonie@kernel.org>

Add helper iterator macros for iterating over the source and sink paths of
widget. This will make it easier to change the implementation later on.
Signed-off-by: NLars-Peter Clausen <lars@metafoo.de>
Signed-off-by: NMark Brown <broonie@kernel.org>

This helper function will be used by the Skylake driver for dsp and
ipc initialization if processing pipe capability is supported.
Signed-off-by: NJeeja KP <jeeja.kp@intel.com>
Signed-off-by: NVinod Koul <vinod.koul@intel.com>
Signed-off-by: NMark Brown <broonie@kernel.org>

The Non-HD Audio Endpoint Description table contains the link
configuration information for the DSP. This is specific to Non HDA
links only, like I2s and PDM

Skylake driver will use NHLT table to retrieve the configuration based
on the link type, format, channel and rate. This configuration is
passed to DSP FW
Signed-off-by: NJeeja KP <jeeja.kp@intel.com>
Signed-off-by: NVinod Koul <vinod.koul@intel.com>
Signed-off-by: NMark Brown <broonie@kernel.org>

Signed-off-by: NOmair M Abdullah <omair.m.abdullah@intel.com>
Signed-off-by: NSubhransu S. Prusty <subhransu.s.prusty@intel.com>
Signed-off-by: NVinod Koul <vinod.koul@intel.com>
Signed-off-by: NMark Brown <broonie@kernel.org>

This adds the dsp and ipc initialization for the Skylake platform.
It also requests firmware and uses code loader dma to load it.
Signed-off-by: NSubhransu S. Prusty <subhransu.s.prusty@intel.com>
Signed-off-by: NJeeja KP <jeeja.kp@intel.com>
Signed-off-by: NVinod Koul <vinod.koul@intel.com>
Signed-off-by: NMark Brown <broonie@kernel.org>

The code loader DMA interrupt is received by main interrupt handler which
dispatches it to cldma routines
Signed-off-by: NSubhransu S. Prusty <subhransu.s.prusty@intel.com>
Signed-off-by: NVinod Koul <vinod.koul@intel.com>
Signed-off-by: NMark Brown <broonie@kernel.org>

This patch adds the last piece of code loader DMA APIs by adding the code
loader DMA APIs for the driver to use
Signed-off-by: NSubhransu S. Prusty <subhransu.s.prusty@intel.com>
Signed-off-by: NJeeja KP <jeeja.kp@intel.com>
Signed-off-by: NVinod Koul <vinod.koul@intel.com>
Signed-off-by: NMark Brown <broonie@kernel.org>

This patch starts adding code loader DMA handling internal operations for
setting up bdle, controller, spb, cleanup routines and buffer filling
Signed-off-by: NSubhransu S. Prusty <subhransu.s.prusty@intel.com>
Signed-off-by: NJeeja KP <jeeja.kp@intel.com>
Signed-off-by: NVinod Koul <vinod.koul@intel.com>
Signed-off-by: NMark Brown <broonie@kernel.org>

Skylake has a DMA controller for loading DSP code and modules to memory.
Add the register defines for this DMA
Signed-off-by: NSubhransu S. Prusty <subhransu.s.prusty@intel.com>
Signed-off-by: NJeeja KP <jeeja.kp@intel.com>
Signed-off-by: NVinod Koul <vinod.koul@intel.com>
Signed-off-by: NMark Brown <broonie@kernel.org>

The ops is initialized during the dsp registration and used for the
allocating dma buffers.
Signed-off-by: NSubhransu S. Prusty <subhransu.s.prusty@intel.com>
Signed-off-by: NJeeja KP <jeeja.kp@intel.com>
Signed-off-by: NVinod Koul <vinod.koul@intel.com>
Signed-off-by: NMark Brown <broonie@kernel.org>

The usage_count variable was read before it was set to the correct
value, due to which the firmware load was failing. Because of this
IPC messages sent to the firmware were timing out causing a delay
of about 1 second while playing audio from the internal speakers.

With this patch the usage_count is read after the function call
pm_runtime_get_sync which will increment the usage_count variable
and the firmware load is successful and all the IPC messages are
processed correctly.
Signed-off-by: NShilpa Sreeramalu <shilpa.sreeramalu@intel.com>
Signed-off-by: NFang, Yang A <yang.a.fang@intel.com>
Signed-off-by: NMark Brown <broonie@kernel.org>
Cc: stable@vger.kernel.org

This patch adds code to enable, disable and boot DSP core.
Also provide some helpers to reset and power up/down the core.
Signed-off-by: NSubhransu S. Prusty <subhransu.s.prusty@intel.com>
Signed-off-by: NJeeja KP <jeeja.kp@intel.com>
Signed-off-by: NVinod Koul <vinod.koul@intel.com>
Signed-off-by: NMark Brown <broonie@kernel.org>

This adds base SKL IPC library which uses common SST IPC lib.
Here we add definition for IPC types, sending and receiving IPC messages
from aDSP, handling interrupt, sending different types of messages etc
Signed-off-by: NSubhransu S. Prusty <subhransu.s.prusty@intel.com>
Signed-off-by: NJeeja KP <jeeja.kp@intel.com>
Signed-off-by: NVinod Koul <vinod.koul@intel.com>
Signed-off-by: NMark Brown <broonie@kernel.org>