This allows saving a little of space when not using ssb on Broadcom SoC.
Signed-off-by: NRafał Miłecki <zajec5@gmail.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

This cleans main.c a bit and will allow us to compile SoC related code
conditionally in the future.
Signed-off-by: NRafał Miłecki <zajec5@gmail.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

ssb bus can be found on various "host" devices like PCI/PCMCIA/SDIO.
Every ssb bus contains cores AKA devices.
The main idea is to have ssb driver scan/initialize bus and register
ready-to-use cores. This way ssb drivers can operate on a single core
mostly ignoring underlaying details.

For some reason PCMCIA support was split between ssb and b43. We got
PCMCIA host device probing in b43, then bus scanning in ssb and then
wireless core probing back in b43. The truth is it's very unlikely we
will ever see PCMCIA ssb device with no 802.11 core but I still don't
see any advantage of the current architecture.

With proposed change we get the same functionality with a simpler
architecture, less Kconfig symbols, one killed EXPORT and hopefully
cleaner b43. Since b43 supports both: ssb & bcma I prefer to keep ssb
specific code in ssb driver.

This mostly moves code from b43's pcmcia.c to bridge_pcmcia_80211.c. We
already use similar solution with b43_pci_bridge.c. I didn't use "b43"
in name of this new file as in theory any driver can operate on wireless
core.
Signed-off-by: NRafał Miłecki <zajec5@gmail.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

In uap mode the carrier is not enabled until after the first STA joins.
The carrier triggers the bridge to start its state machine, and if STP
is enabled, it takes 4 seconds as it transitions from disabled to
forwarding. During this time the bridge drops all traffic, and the EAPOL
handshake times out after 3 seconds, preventing stations from joining.

Follow the logic used in mac80211 and start the carrier in start_ap
and disable it in stop_ap. This has a nice benefit of allowing the
first station connection time to be reduced by up to 75% when STP is
in use.
Signed-off-by: NMartin Faltesek <mfaltesek@google.com>
Signed-off-by: NAmitkumar Karwar <akarwar@marvell.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

arm64 has requirement that all the dma operations have actual device.
Otherwise, following warnning message shown and dma allocation fails:

WARNING: CPU: 0 PID: 954 at arch/arm64/mm/dma-mapping.c:106 __dma_alloc+0x24c/0x258()
Use an actual device structure for DMA allocation
Modules linked in: wcn36xx wcn36xx_platform
CPU: 0 PID: 954 Comm: ifconfig Not tainted 4.0.0+ #14
Hardware name: Qualcomm Technologies, Inc. MSM 8916 MTP (DT)
Call trace:
[<ffffffc000089904>] dump_backtrace+0x0/0x124
[<ffffffc000089a38>] show_stack+0x10/0x1c
[<ffffffc000627114>] dump_stack+0x80/0xc4
[<ffffffc0000b2e64>] warn_slowpath_common+0x98/0xd0
[<ffffffc0000b2ee8>] warn_slowpath_fmt+0x4c/0x58
[<ffffffc00009487c>] __dma_alloc+0x248/0x258
[<ffffffbffc009270>] wcn36xx_dxe_allocate_mem_pools+0xc4/0x108 [wcn36xx]
[<ffffffbffc0079c4>] wcn36xx_start+0x38/0x240 [wcn36xx]
[<ffffffc0005f161c>] ieee80211_do_open+0x1b0/0x9a4
[<ffffffc0005f1e68>] ieee80211_open+0x58/0x68
[<ffffffc00051693c>] __dev_open+0xb0/0x120
[<ffffffc000516c10>] __dev_change_flags+0x88/0x150
[<ffffffc000516cf4>] dev_change_flags+0x1c/0x5c
[<ffffffc000570950>] devinet_ioctl+0x644/0x6f0
Signed-off-by: NYin, Fengwei <fengwei.yin@linaro.org>
Acked-by: NBjorn Andersson <bjorn.andersson@sonymobile.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

wcn36xx implements a ring buffer for transmitted frames for each
(high and low priority) DMA channel.  The ring buffers are lockless:
new frames are inserted at the head of the queue, while finished
packets are reaped from the tail.

Unfortunately, the list manipulations are missing any kind of barriers
so are susceptible to various races: for example, a TX completion
handler might read an updated desc->ctrl before the head has actually
advanced, and then null out the ctl->skb pointer while it is still
being used in the TX path.

Simplify things here by adding a spin lock when traversing the ring.
This change increased stability for me without adding any noticeable
overhead on my platform (xperia z).
Signed-off-by: NBob Copeland <me@bobcopeland.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

Some of the ath9k_phyerr enums were wrong from the
beginning (and even before). Most of the time the
codes were used for counters to be displayed over
debugfs, which made this a non-functional issue.

Some (e.g. ATH9K_PHYERR_FALSE_RADAR_EXT) are used
for radar detection and require the correct code
to work as intended.

This patch includes:
a) fixes
  ATH9K_PHYERR_FALSE_RADAR_EXT:    24 => 36
  ATH9K_PHYERR_CCK_LENGTH_ILLEGAL: 32 => 28
  ATH9K_PHYERR_CCK_POWER_DROP:     33 => 29
  ATH9K_PHYERR_HT_CRC_ERROR:       34 => 32
  ATH9K_PHYERR_HT_LENGTH_ILLEGAL:  35 => 33
  ATH9K_PHYERR_HT_RATE_ILLEGAL:    36 => 34

b) extensions
  ATH9K_PHYERR_CCK_BLOCKER = 24
  ATH9K_PHYERR_HT_ZLF      = 35
  ATH9K_PHYERR_GREEN_FIELD = 37

Aside from the correction and completion made in
the enum, the patch also extends the display of
the related counters in the debugfs.
Signed-off-by: NZefir Kurtisi <zefir.kurtisi@neratec.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

The current code exits after alloc_orinocodev, but fails to change the
return value to something that indicates the failure.  This patch
changes the return value to -ENOMEM.

https://bugzilla.kernel.org/show_bug.cgi?id=106181Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

SIOCSIWAP (airo_set_wap) affects scan: only the AP specified by
SIOCSIWAP is present in scan results.

This makes NetworkManager work for the first time but then unable to
find any other APs.

Clear APList before starting scan and set it back after scan completes
to work-around the problem.

To avoid losing packets during scan, modify disable_MAC() to omit
netif_carrier_off() call when lock == 2.
Signed-off-by: NOndrej Zary <linux@rainbow-software.org>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

Instead of dynamically allocating APList, make it a member of struct
airo_info to always track state of APList_rid.
This simplifies suspend/resume and allows removal of readAPListRid.
Signed-off-by: NOndrej Zary <linux@rainbow-software.org>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

delete action of ETHTOOL_ID_ON/ETHTOOL_ID_OFF in XGE ethtool -p,
so Hardware control the LED state instead of software.
Signed-off-by: NLi Peng <lipeng321@huawei.com>
Signed-off-by: NYisen Zhuang <yisen.zhuang@huawei.com>
Signed-off-by: Nyankejian <yankejian@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Increased TX_TIMEOUT to 5HZ to accommodate worst case situation
for traffic and CPU intensive use cases
Signed-off-by: NPriyanka Jain <Priyanka.Jain@freescale.com>
Signed-off-by: NAbhimanyu <abhimanyu@freescale.com>
Acked-by: NClaudiu Manoil <claudiu.manoil@freescale.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch reduces the overhead of locking for busy poll.
Previously the state was protected by a lock, whereas now
it's manipulated solely with atomic operations.
Signed-off-by: NShradha Shah <sshah@solarflare.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This adds basic ethtool operations to the qed driver, allowing support in:
 - Statistics gathering [ethtool -S]
 - Setting of debug level [ethtool -s <interface> msglvl]
 - Getting basic information [ethtool, ethtool -i]

In addition it adds the ability to change the MTU.
Signed-off-by: NSudarsana Kalluru <Sudarsana.Kalluru@qlogic.com>
Signed-off-by: NYuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: NAriel Elior <Ariel.Elior@qlogic.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Device statistics can be gathered on-demand. This adds the qed support for
reading the statistics [both function and port] from the device, and adds
to the public API a method for requesting the current statistics.
Signed-off-by: NManish Chopra <Manish.Chopra@qlogic.com>
Signed-off-by: NYuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: NAriel Elior <Ariel.Elior@qlogic.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This adds basic link functionality to qede - driver still doesn't provide
users with an API to change any link property, but it does request qed to
initialize the link using default configuration, and registers a callback
that allows it to get link notifications.

This patch adds the ability of the driver to set the carrier as active and
to enable traffic as a result of async. link notifications.
Following this patch, driver should be capable of running traffic.
Signed-off-by: NSudarsana Kalluru <Sudarsana.Kalluru@qlogic.com>
Signed-off-by: NYuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: NAriel Elior <Ariel.Elior@qlogic.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Physical link is handled by the management Firmware.
This patch lays the infrastructure for attention handling in the driver,
as link change notifications arrive via async. attentions,
as well the handling of such notifications.

This patch also extends the API with the protocol drivers by adding
registered callbacks which the protocol driver passes to qed in order
to be notified of async. events originating from the FW/HW.
Signed-off-by: NYuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: NAriel Elior <Ariel.Elior@qlogic.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add the ability to configure basic classification in driver by
implementing ndo_set_mac_address() and ndo_set_rx_mode().
Signed-off-by: NSudarsana Kalluru <Sudarsana.Kalluru@qlogic.com>
Signed-off-by: NYuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: NAriel Elior <Ariel.Elior@qlogic.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch includes the basic Rx/Tx support for the driver [although
carrier will still never be turned on].
Following this patch the driver registers a network device, initializes
it and prepares it for traffic.
Signed-off-by: NSudarsana Kalluru <Sudarsana.Kalluru@qlogic.com>
Signed-off-by: NYuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: NAriel Elior <Ariel.Elior@qlogic.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch adds to the qed the support to configure various L2 elements,
such as channels and basic filtering conditions.
It also enhances its public API to allow qede to later utilize this
functionality.
Signed-off-by: NManish Chopra <Manish.Chopra@qlogic.com>
Signed-off-by: NYuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: NAriel Elior <Ariel.Elior@qlogic.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The Qlogic Everest Driver for Ethernet is the Ethernet specific module for
QL4xxx ethernet products by Qlogic.

This patch adds a very minimal PCI driver, one that doesn't yet register
a network device, but one that does interact with qed and does a basic
initialization of the HW.
Signed-off-by: NYuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: NAriel Elior <Ariel.Elior@qlogic.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch adds a public API for a network driver to work on top of QED.
The interface itself is very minimal - it's mostly infrastructure, as the
only content it has after this patch is a query for HW-based information
required for the creation of a network interface [I.e., no actual
protocol-specific configurations are supported].
Signed-off-by: NManish Chopra <Manish.Chopra@qlogic.com>
Signed-off-by: NYuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: NAriel Elior <Ariel.Elior@qlogic.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The Qlogic Everest Driver is the backend module for the QL4xxx ethernet
products by Qlogic.

This module serves two main purposes:
 1. It's responsible to contain all the common code that will be shared
    between the various drivers that would be used with said line of
    products. Flows such as chip initialization and de-initialization
    fall under this category.

 2. It would abstract the protocol-specific HW & FW components, allowing
    the protocol drivers to have a clean APIs which is detached in its
    slowpath configuration from the actual HSI.

This adds a very basic module without any protocol-specific bits.
I.e., this adds a basic implementation that almost entirely falls under
the first category.
Signed-off-by: NYuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: NAriel Elior <Ariel.Elior@qlogic.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

While the current driver mostly supports BCM7445 which has a hardcoded
location for its MoCA port on port 7 and port 0 for its internal PHY,
this is not necessarily true for all other chips out there such as
BCM3390 for instance.

Walk the list of ports from Device Tree, get their port number ("reg"
property), and then parse the "phy-mode" property and initialize two
internal variables: moca_port and a bitmask of internal PHYs. Since we
use interrupts for the MoCA port, we introduce two helper functions to
enable/disable interrupts and do this at the appropriate bank (INTRL2_0
or INTRL2_1).
Signed-off-by: NFlorian Fainelli <f.fainelli@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add support for the FDB add, delete, and dump operations. The add and
delete operations are implemented using directed ARL operations using
the specified MAC address and consist in a read operation, write and
readback operation.

The dump operation consists in using the ARL search and software
filtering entries which are not for the desired port.
Signed-off-by: NFlorian Fainelli <f.fainelli@gmail.com>
Reviewed-by: NVivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

kbuild reported:

rtl8xxxu.c:5786:32: warning: ‘rtl8192cu_fops’ defined but not used [-Wunused-variable]

Fix it by adding temporary ifdefs around the static functions.

Fixes: 033695bd ("rtl8xxxu: move devices supported by rtlwifi under UNTESTED config")
Reported-by: Nkbuild test robot <fengguang.wu@intel.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

The arcnet device has no interrupt to detect if the link has changed
from disconnected to connected. This patch adds an timer to toggle the
link detection. The timer will get retriggered as long as the
reconnection interrupts accure. If the recon interrupts hold off
for >1s we define the connection stable again.
Signed-off-by: NMichael Grzeschik <m.grzeschik@pengutronix.de>

The EAE PLX-PCI card has special leds on the the main io pci resource
bar. This patch adds support to trigger the conflict and data leds with
the packages.
Signed-off-by: NMichael Grzeschik <m.grzeschik@pengutronix.de>

The EAE PLX-PCI card has a special rotary encoder
to configure the address of every card individually.
We take this information for the initial setup of
the cards dev_id.
Signed-off-by: NMichael Grzeschik <m.grzeschik@pengutronix.de>

This patch sets the dev_port according to the index of
the card. This can be used by udev to name the ports
in userspace.
Signed-off-by: NMichael Grzeschik <m.grzeschik@pengutronix.de>

This patch changes the driver to properly work with the linux netif
interface. The controller gets enabled on open and disabled on close.
Therefor it removes every bogus start of the xceiver. It only gets
enabled on com20020_open and disabled on com20020_close.
Signed-off-by: NMichael Grzeschik <m.grzeschik@pengutronix.de>

The call for dev_free_skb is done only once. This patch
moves its call to its only user and removes the obsolete
condition variable.
Signed-off-by: NMichael Grzeschik <m.grzeschik@pengutronix.de>

bnxt_gro_skb() has unused variables when CONFIG_INET is not set.  We
really cannot support hardware GRO if CONFIG_INET is not set, so
compile out bnxt_gro_skb() completely and define BNXT_FLAG_GRO to be 0
if CONFIG_INET is not set.  This will effectively always disable
hardware GRO if CONFIG_INET is not set.
Signed-off-by: NMichael Chan <mchan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This fixes the mask used to update the LED configuration so that it clears
the necessary bits as well as setting the bits according to the mask.
Also reverse the LED configuration to show the Link state + collisions in
LEDA and the Link state + TX/RX events in LEDB.
Signed-off-by: NJon Ringle <jringle@gridpoint.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The existing function to clear the MIB statatistics was using the
wrong address for the registers. Also, the counters would of been
cleared when the interface was brought up, not during the
probe. Fix both of these.
Signed-off-by: NAndrew Lunn <andrew@lunn.ch>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add support for the ethtool statistic interface, returning the full set
of statistics which both Armada 370, 38x and Armada XP can support.
Tested-by: NAndrew Lunn <andrew@lunn.ch>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When reading external NVM file, if a section exists both in OTP
and in the external file, the memory that was allocated at OTP
reading is not freed.
This is possible only on systems that have an external NVM
file which is typically the case on embedded systems.
Signed-off-by: NMoshe Harel <moshe.harel@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

The iwl_mvm_disable_queue function requires the TID to be set to
IWL_MAX_TID_COUNT when disabling an AC queue. Call it correctly for TDLS
scenarios.

Fixes: 4ecafae9 ("iwlwifi: mvm: support using multiple ACs on single HW queue")
Signed-off-by: NArik Nemtsov <arikx.nemtsov@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

In some cases, scan reference was taken, but wasn't
released even though scan command wasn't actually issued.

Change the current code to simply take the reference
only on success.
Signed-off-by: NEliad Peller <eliadx.peller@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

As cfg80211 already enforces these limits, there's little point
in having them again here in our code.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>