On some codepaths the skb does not have a dst entry
when xfrm_decode_session() is called. So check for
a valid skb_dst() before dereferencing the device
interface index. We use 0 as the device index if
there is no valid skb_dst(), or at reverse decoding
we use skb_iif as device interface index.

Bug was introduced with git commit bafd4bd4
("xfrm: Decode sessions with output interface.").
Reported-by: NMeelis Roos <mroos@linux.ee>
Tested-by: NMeelis Roos <mroos@linux.ee>
Signed-off-by: NSteffen Klassert <steffen.klassert@secunet.com>

With the removal of the routing cache, we lost the
option to tweak the garbage collector threshold
along with the maximum routing cache size. So git
commit 703fb94e ("xfrm: Fix the gc threshold value
for ipv4") moved back to a static threshold.

It turned out that the current threshold before we
start garbage collecting is much to small for some
workloads, so increase it from 1024 to 32768. This
means that we start the garbage collector if we have
more than 32768 dst entries in the system and refuse
new allocations if we are above 65536.
Reported-by: NWolfgang Walter <linux@stwm.de>
Signed-off-by: NSteffen Klassert <steffen.klassert@secunet.com>

In ipcomp_compress(), sortirq is enabled too early, allowing the
per-cpu scratch buffer to be rewritten by ipcomp_decompress()
(called on the same CPU in softirq context) between populating
the buffer and copying the compressed data to the skb.

v2: as pointed out by Steffen Klassert, if we also move the
local_bh_disable() before reading the per-cpu pointers, we can
get rid of get_cpu()/put_cpu().

v3: removed ipcomp_decompress part (as explained by Herbert Xu,
it cannot be called from process context), get rid of cpu
variable (thanks to Eric Dumazet)
Signed-off-by: NMichal Kubecek <mkubecek@suse.cz>
Reviewed-by: NEric Dumazet <edumazet@google.com>
Acked-by: NHerbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: NSteffen Klassert <steffen.klassert@secunet.com>

SMC_outw invokes an endian-aware I/O accessor, which may change the data
endianness before writing to the device. This is not suitable for data
transfers where the memory buffer is simply a string of bytes that does
not require any byte-swapping.

This patches fixes the smc91x SMC_PUSH_DATA macro so that it uses the
string I/O accessor for outputting the leading or trailing halfwords on
halfword-aligned buffers.

Cc: <netdev@vger.kernel.org>
Cc: Nicolas Pitre <nico@fluxnic.net>
Cc: David S. Miller <davem@davemloft.net>
Signed-off-by: NWill Deacon <will.deacon@arm.com>
Acked-by: NNicolas Pitre <nico@linaro.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The fst_get_iface() code fails to initialize the two padding bytes of
struct sync_serial_settings after the ->loopback member. Add an explicit
memset(0) before filling the structure to avoid the info leak.
Signed-off-by: NDan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The ip6_tnl.hlen (gre and ipv6 headers length) is independent from the
outgoing interface, so it would be better to initialize it even when no
route is found, otherwise its value will be zero.
While I'm not sure if this could happen in real life, but doing that
will avoid to call the skb_push function with a zero in ip6gre_header
function.
Suggested-by: NHannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: NOussama Ghorbel <ou.ghorbel@gmail.com>
Acked-by: NHannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Netem can leak memory because packets get stored in red-black
tree and it is not cleared on reset.

Reported by: Сергеев Сергей <adron@yapic.net>
Signed-off-by: NStephen Hemminger <stephen@networkplumber.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When packet is dropped from rb-tree netem the backlog statistic should
also be updated.
Reported-by: NСергеев Сергей <adron@yapic.net>
Signed-off-by: NStephen Hemminger <stephen@networkplumber.org>
Acked-by: NEric Dumazet <edumazet@google.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

François Cachereul made a very nice bug report and suspected
the bh_lock_sock() / bh_unlok_sock() pair used in l2tp_xmit_skb() from
process context was not good.

This problem was added by commit 6af88da1
("l2tp: Fix locking in l2tp_core.c").

l2tp_eth_dev_xmit() runs from BH context, so we must disable BH
from other l2tp_xmit_skb() users.

[  452.060011] BUG: soft lockup - CPU#1 stuck for 23s! [accel-pppd:6662]
[  452.061757] Modules linked in: l2tp_ppp l2tp_netlink l2tp_core pppoe pppox
ppp_generic slhc ipv6 ext3 mbcache jbd virtio_balloon xfs exportfs dm_mod
virtio_blk ata_generic virtio_net floppy ata_piix libata virtio_pci virtio_ring virtio [last unloaded: scsi_wait_scan]
[  452.064012] CPU 1
[  452.080015] BUG: soft lockup - CPU#2 stuck for 23s! [accel-pppd:6643]
[  452.080015] CPU 2
[  452.080015]
[  452.080015] Pid: 6643, comm: accel-pppd Not tainted 3.2.46.mini #1 Bochs Bochs
[  452.080015] RIP: 0010:[<ffffffff81059f6c>]  [<ffffffff81059f6c>] do_raw_spin_lock+0x17/0x1f
[  452.080015] RSP: 0018:ffff88007125fc18  EFLAGS: 00000293
[  452.080015] RAX: 000000000000aba9 RBX: ffffffff811d0703 RCX: 0000000000000000
[  452.080015] RDX: 00000000000000ab RSI: ffff8800711f6896 RDI: ffff8800745c8110
[  452.080015] RBP: ffff88007125fc18 R08: 0000000000000020 R09: 0000000000000000
[  452.080015] R10: 0000000000000000 R11: 0000000000000280 R12: 0000000000000286
[  452.080015] R13: 0000000000000020 R14: 0000000000000240 R15: 0000000000000000
[  452.080015] FS:  00007fdc0cc24700(0000) GS:ffff8800b6f00000(0000) knlGS:0000000000000000
[  452.080015] CS:  0010 DS: 0000 ES: 0000 CR0: 0000000080050033
[  452.080015] CR2: 00007fdb054899b8 CR3: 0000000074404000 CR4: 00000000000006a0
[  452.080015] DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
[  452.080015] DR3: 0000000000000000 DR6: 00000000ffff0ff0 DR7: 0000000000000400
[  452.080015] Process accel-pppd (pid: 6643, threadinfo ffff88007125e000, task ffff8800b27e6dd0)
[  452.080015] Stack:
[  452.080015]  ffff88007125fc28 ffffffff81256559 ffff88007125fc98 ffffffffa01b2bd1
[  452.080015]  ffff88007125fc58 000000000000000c 00000000029490d0 0000009c71dbe25e
[  452.080015]  000000000000005c 000000080000000e 0000000000000000 ffff880071170600
[  452.080015] Call Trace:
[  452.080015]  [<ffffffff81256559>] _raw_spin_lock+0xe/0x10
[  452.080015]  [<ffffffffa01b2bd1>] l2tp_xmit_skb+0x189/0x4ac [l2tp_core]
[  452.080015]  [<ffffffffa01c2d36>] pppol2tp_sendmsg+0x15e/0x19c [l2tp_ppp]
[  452.080015]  [<ffffffff811c7872>] __sock_sendmsg_nosec+0x22/0x24
[  452.080015]  [<ffffffff811c83bd>] sock_sendmsg+0xa1/0xb6
[  452.080015]  [<ffffffff81254e88>] ? __schedule+0x5c1/0x616
[  452.080015]  [<ffffffff8103c7c6>] ? __dequeue_signal+0xb7/0x10c
[  452.080015]  [<ffffffff810bbd21>] ? fget_light+0x75/0x89
[  452.080015]  [<ffffffff811c8444>] ? sockfd_lookup_light+0x20/0x56
[  452.080015]  [<ffffffff811c9b34>] sys_sendto+0x10c/0x13b
[  452.080015]  [<ffffffff8125cac2>] system_call_fastpath+0x16/0x1b
[  452.080015] Code: 81 48 89 e5 72 0c 31 c0 48 81 ff 45 66 25 81 0f 92 c0 5d c3 55 b8 00 01 00 00 48 89 e5 f0 66 0f c1 07 0f b6 d4 38 d0 74 06 f3 90 <8a> 07 eb f6 5d c3 90 90 55 48 89 e5 9c 58 0f 1f 44 00 00 5d c3
[  452.080015] Call Trace:
[  452.080015]  [<ffffffff81256559>] _raw_spin_lock+0xe/0x10
[  452.080015]  [<ffffffffa01b2bd1>] l2tp_xmit_skb+0x189/0x4ac [l2tp_core]
[  452.080015]  [<ffffffffa01c2d36>] pppol2tp_sendmsg+0x15e/0x19c [l2tp_ppp]
[  452.080015]  [<ffffffff811c7872>] __sock_sendmsg_nosec+0x22/0x24
[  452.080015]  [<ffffffff811c83bd>] sock_sendmsg+0xa1/0xb6
[  452.080015]  [<ffffffff81254e88>] ? __schedule+0x5c1/0x616
[  452.080015]  [<ffffffff8103c7c6>] ? __dequeue_signal+0xb7/0x10c
[  452.080015]  [<ffffffff810bbd21>] ? fget_light+0x75/0x89
[  452.080015]  [<ffffffff811c8444>] ? sockfd_lookup_light+0x20/0x56
[  452.080015]  [<ffffffff811c9b34>] sys_sendto+0x10c/0x13b
[  452.080015]  [<ffffffff8125cac2>] system_call_fastpath+0x16/0x1b
[  452.064012]
[  452.064012] Pid: 6662, comm: accel-pppd Not tainted 3.2.46.mini #1 Bochs Bochs
[  452.064012] RIP: 0010:[<ffffffff81059f6e>]  [<ffffffff81059f6e>] do_raw_spin_lock+0x19/0x1f
[  452.064012] RSP: 0018:ffff8800b6e83ba0  EFLAGS: 00000297
[  452.064012] RAX: 000000000000aaa9 RBX: ffff8800b6e83b40 RCX: 0000000000000002
[  452.064012] RDX: 00000000000000aa RSI: 000000000000000a RDI: ffff8800745c8110
[  452.064012] RBP: ffff8800b6e83ba0 R08: 000000000000c802 R09: 000000000000001c
[  452.064012] R10: ffff880071096c4e R11: 0000000000000006 R12: ffff8800b6e83b18
[  452.064012] R13: ffffffff8125d51e R14: ffff8800b6e83ba0 R15: ffff880072a589c0
[  452.064012] FS:  00007fdc0b81e700(0000) GS:ffff8800b6e80000(0000) knlGS:0000000000000000
[  452.064012] CS:  0010 DS: 0000 ES: 0000 CR0: 0000000080050033
[  452.064012] CR2: 0000000000625208 CR3: 0000000074404000 CR4: 00000000000006a0
[  452.064012] DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
[  452.064012] DR3: 0000000000000000 DR6: 00000000ffff0ff0 DR7: 0000000000000400
[  452.064012] Process accel-pppd (pid: 6662, threadinfo ffff88007129a000, task ffff8800744f7410)
[  452.064012] Stack:
[  452.064012]  ffff8800b6e83bb0 ffffffff81256559 ffff8800b6e83bc0 ffffffff8121c64a
[  452.064012]  ffff8800b6e83bf0 ffffffff8121ec7a ffff880072a589c0 ffff880071096c62
[  452.064012]  0000000000000011 ffffffff81430024 ffff8800b6e83c80 ffffffff8121f276
[  452.064012] Call Trace:
[  452.064012]  <IRQ>
[  452.064012]  [<ffffffff81256559>] _raw_spin_lock+0xe/0x10
[  452.064012]  [<ffffffff8121c64a>] spin_lock+0x9/0xb
[  452.064012]  [<ffffffff8121ec7a>] udp_queue_rcv_skb+0x186/0x269
[  452.064012]  [<ffffffff8121f276>] __udp4_lib_rcv+0x297/0x4ae
[  452.064012]  [<ffffffff8121c178>] ? raw_rcv+0xe9/0xf0
[  452.064012]  [<ffffffff8121f4a7>] udp_rcv+0x1a/0x1c
[  452.064012]  [<ffffffff811fe385>] ip_local_deliver_finish+0x12b/0x1a5
[  452.064012]  [<ffffffff811fe54e>] ip_local_deliver+0x53/0x84
[  452.064012]  [<ffffffff811fe1d0>] ip_rcv_finish+0x2bc/0x2f3
[  452.064012]  [<ffffffff811fe78f>] ip_rcv+0x210/0x269
[  452.064012]  [<ffffffff8101911e>] ? kvm_clock_get_cycles+0x9/0xb
[  452.064012]  [<ffffffff811d88cd>] __netif_receive_skb+0x3a5/0x3f7
[  452.064012]  [<ffffffff811d8eba>] netif_receive_skb+0x57/0x5e
[  452.064012]  [<ffffffff811cf30f>] ? __netdev_alloc_skb+0x1f/0x3b
[  452.064012]  [<ffffffffa0049126>] virtnet_poll+0x4ba/0x5a4 [virtio_net]
[  452.064012]  [<ffffffff811d9417>] net_rx_action+0x73/0x184
[  452.064012]  [<ffffffffa01b2cc2>] ? l2tp_xmit_skb+0x27a/0x4ac [l2tp_core]
[  452.064012]  [<ffffffff810343b9>] __do_softirq+0xc3/0x1a8
[  452.064012]  [<ffffffff81013b56>] ? ack_APIC_irq+0x10/0x12
[  452.064012]  [<ffffffff81256559>] ? _raw_spin_lock+0xe/0x10
[  452.064012]  [<ffffffff8125e0ac>] call_softirq+0x1c/0x26
[  452.064012]  [<ffffffff81003587>] do_softirq+0x45/0x82
[  452.064012]  [<ffffffff81034667>] irq_exit+0x42/0x9c
[  452.064012]  [<ffffffff8125e146>] do_IRQ+0x8e/0xa5
[  452.064012]  [<ffffffff8125676e>] common_interrupt+0x6e/0x6e
[  452.064012]  <EOI>
[  452.064012]  [<ffffffff810b82a1>] ? kfree+0x8a/0xa3
[  452.064012]  [<ffffffffa01b2cc2>] ? l2tp_xmit_skb+0x27a/0x4ac [l2tp_core]
[  452.064012]  [<ffffffffa01b2c25>] ? l2tp_xmit_skb+0x1dd/0x4ac [l2tp_core]
[  452.064012]  [<ffffffffa01c2d36>] pppol2tp_sendmsg+0x15e/0x19c [l2tp_ppp]
[  452.064012]  [<ffffffff811c7872>] __sock_sendmsg_nosec+0x22/0x24
[  452.064012]  [<ffffffff811c83bd>] sock_sendmsg+0xa1/0xb6
[  452.064012]  [<ffffffff81254e88>] ? __schedule+0x5c1/0x616
[  452.064012]  [<ffffffff8103c7c6>] ? __dequeue_signal+0xb7/0x10c
[  452.064012]  [<ffffffff810bbd21>] ? fget_light+0x75/0x89
[  452.064012]  [<ffffffff811c8444>] ? sockfd_lookup_light+0x20/0x56
[  452.064012]  [<ffffffff811c9b34>] sys_sendto+0x10c/0x13b
[  452.064012]  [<ffffffff8125cac2>] system_call_fastpath+0x16/0x1b
[  452.064012] Code: 89 e5 72 0c 31 c0 48 81 ff 45 66 25 81 0f 92 c0 5d c3 55 b8 00 01 00 00 48 89 e5 f0 66 0f c1 07 0f b6 d4 38 d0 74 06 f3 90 8a 07 <eb> f6 5d c3 90 90 55 48 89 e5 9c 58 0f 1f 44 00 00 5d c3 55 48
[  452.064012] Call Trace:
[  452.064012]  <IRQ>  [<ffffffff81256559>] _raw_spin_lock+0xe/0x10
[  452.064012]  [<ffffffff8121c64a>] spin_lock+0x9/0xb
[  452.064012]  [<ffffffff8121ec7a>] udp_queue_rcv_skb+0x186/0x269
[  452.064012]  [<ffffffff8121f276>] __udp4_lib_rcv+0x297/0x4ae
[  452.064012]  [<ffffffff8121c178>] ? raw_rcv+0xe9/0xf0
[  452.064012]  [<ffffffff8121f4a7>] udp_rcv+0x1a/0x1c
[  452.064012]  [<ffffffff811fe385>] ip_local_deliver_finish+0x12b/0x1a5
[  452.064012]  [<ffffffff811fe54e>] ip_local_deliver+0x53/0x84
[  452.064012]  [<ffffffff811fe1d0>] ip_rcv_finish+0x2bc/0x2f3
[  452.064012]  [<ffffffff811fe78f>] ip_rcv+0x210/0x269
[  452.064012]  [<ffffffff8101911e>] ? kvm_clock_get_cycles+0x9/0xb
[  452.064012]  [<ffffffff811d88cd>] __netif_receive_skb+0x3a5/0x3f7
[  452.064012]  [<ffffffff811d8eba>] netif_receive_skb+0x57/0x5e
[  452.064012]  [<ffffffff811cf30f>] ? __netdev_alloc_skb+0x1f/0x3b
[  452.064012]  [<ffffffffa0049126>] virtnet_poll+0x4ba/0x5a4 [virtio_net]
[  452.064012]  [<ffffffff811d9417>] net_rx_action+0x73/0x184
[  452.064012]  [<ffffffffa01b2cc2>] ? l2tp_xmit_skb+0x27a/0x4ac [l2tp_core]
[  452.064012]  [<ffffffff810343b9>] __do_softirq+0xc3/0x1a8
[  452.064012]  [<ffffffff81013b56>] ? ack_APIC_irq+0x10/0x12
[  452.064012]  [<ffffffff81256559>] ? _raw_spin_lock+0xe/0x10
[  452.064012]  [<ffffffff8125e0ac>] call_softirq+0x1c/0x26
[  452.064012]  [<ffffffff81003587>] do_softirq+0x45/0x82
[  452.064012]  [<ffffffff81034667>] irq_exit+0x42/0x9c
[  452.064012]  [<ffffffff8125e146>] do_IRQ+0x8e/0xa5
[  452.064012]  [<ffffffff8125676e>] common_interrupt+0x6e/0x6e
[  452.064012]  <EOI>  [<ffffffff810b82a1>] ? kfree+0x8a/0xa3
[  452.064012]  [<ffffffffa01b2cc2>] ? l2tp_xmit_skb+0x27a/0x4ac [l2tp_core]
[  452.064012]  [<ffffffffa01b2c25>] ? l2tp_xmit_skb+0x1dd/0x4ac [l2tp_core]
[  452.064012]  [<ffffffffa01c2d36>] pppol2tp_sendmsg+0x15e/0x19c [l2tp_ppp]
[  452.064012]  [<ffffffff811c7872>] __sock_sendmsg_nosec+0x22/0x24
[  452.064012]  [<ffffffff811c83bd>] sock_sendmsg+0xa1/0xb6
[  452.064012]  [<ffffffff81254e88>] ? __schedule+0x5c1/0x616
[  452.064012]  [<ffffffff8103c7c6>] ? __dequeue_signal+0xb7/0x10c
[  452.064012]  [<ffffffff810bbd21>] ? fget_light+0x75/0x89
[  452.064012]  [<ffffffff811c8444>] ? sockfd_lookup_light+0x20/0x56
[  452.064012]  [<ffffffff811c9b34>] sys_sendto+0x10c/0x13b
[  452.064012]  [<ffffffff8125cac2>] system_call_fastpath+0x16/0x1b
Reported-by: NFrançois Cachereul <f.cachereul@alphalink.fr>
Tested-by: NFrançois Cachereul <f.cachereul@alphalink.fr>
Signed-off-by: NEric Dumazet <edumazet@google.com>
Cc: James Chapman <jchapman@katalix.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Nguyen Hong Ky posted a patch to correct RX packet errors on R8A7740 which
was applied as 2c6221e4 ("net: sh_eth: Fix RX packets errors on
R8A7740"). Unfortunately sh_eth.c contains many similar instances
of struct sh_eth_cpu_data and the patch was miss-applied, updating
sh7734_data instead of r8a7740_data.

This patch corrects this problem by.
1. Reverting the change to sh7734_data and;
2. Applying the change to r8a7740_data.
Signed-off-by: NSimon Horman <horms+renesas@verge.net.au>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch fixes and improves the use of vti interfaces (while
lightly changing the way of configuring them).

Currently:

- it is necessary to identify and mark inbound IPsec
  packets destined to each vti interface, via netfilter rules in
  the mangle table at prerouting hook.

- the vti module cannot retrieve the right tunnel in input since
  commit b9959fd3: vti tunnels all have an i_key, but the tunnel lookup
  is done with flag TUNNEL_NO_KEY, so there no chance to retrieve them.

- the i_key is used by the outbound processing as a mark to lookup
  for the right SP and SA bundle.

This patch uses the o_key to store the vti mark (instead of i_key) and
enables:

- to avoid the need for previously marking the inbound skbuffs via a
  netfilter rule.
- to properly retrieve the right tunnel in input, only based on the IPsec
  packet outer addresses.
- to properly perform an inbound policy check (using the tunnel o_key
  as a mark).
- to properly perform an outbound SPD and SAD lookup (using the tunnel
  o_key as a mark).
- to keep the current mark of the skbuff. The skbuff mark is neither
  used nor changed by the vti interface. Only the vti interface o_key
  is used.

SAs have a wildcard mark.
SPs have a mark equal to the vti interface o_key.

The vti interface must be created as follows (i_key = 0, o_key = mark):

   ip link add vti1 mode vti local 1.1.1.1 remote 2.2.2.2 okey 1

The SPs attached to vti1 must be created as follows (mark = vti1 o_key):

   ip xfrm policy add dir out mark 1 tmpl src 1.1.1.1 dst 2.2.2.2 \
      proto esp mode tunnel
   ip xfrm policy add dir in  mark 1 tmpl src 2.2.2.2 dst 1.1.1.1 \
      proto esp mode tunnel

The SAs are created with the default wildcard mark. There is no
distinction between global vs. vti SAs. Just their addresses will
possibly link them to a vti interface:

   ip xfrm state add src 1.1.1.1 dst 2.2.2.2 proto esp spi 1000 mode tunnel \
                 enc "cbc(aes)" "azertyuiopqsdfgh"

   ip xfrm state add src 2.2.2.2 dst 1.1.1.1 proto esp spi 2000 mode tunnel \
                 enc "cbc(aes)" "sqbdhgqsdjqjsdfh"

To avoid matching "global" (not vti) SPs in vti interfaces, global SPs
should no use the default wildcard mark, but explicitly match mark 0.

To avoid a double SPD lookup in input and output (in global and vti SPDs),
the NOPOLICY and NOXFRM options should be set on the vti interfaces:

   echo 1 > /proc/sys/net/ipv4/conf/vti1/disable_policy
   echo 1 > /proc/sys/net/ipv4/conf/vti1/disable_xfrm

The outgoing traffic is steered to vti1 by a route via the vti interface:

   ip route add 192.168.0.0/16 dev vti1

The incoming IPsec traffic is steered to vti1 because its outer addresses
match the vti1 tunnel configuration.
Signed-off-by: NChristophe Gouault <christophe.gouault@6wind.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

commit 9f00b2e7
	bridge: only expire the mdb entry when query is received
changed the mdb expiration timer to be armed only when QUERY is
received.  Howerver, this causes issues in an environment where
the multicast server socket comes and goes very fast while a client
is trying to send traffic to it.

The root cause is a race where a sequence of LEAVE followed by REPORT
messages can race against QUERY messages generated in response to LEAVE.
The QUERY ends up starting the expiration timer, and that timer can
potentially expire after the new REPORT message has been received signaling
the new join operation.  This leads to a significant drop in multicast
traffic and possible complete stall.

The solution is to have REPORT messages update the expiration timer
on entries that already exist.

CC: Cong Wang <xiyou.wangcong@gmail.com>
CC: Herbert Xu <herbert@gondor.apana.org.au>
CC: Stephen Hemminger <stephen@networkplumber.org>
Signed-off-by: NVlad Yasevich <vyasevic@redhat.com>
Acked-by: NHerbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

In commit:

    3078cde7 can: at91_can: add dt support

device tree support was added to the at91_can driver. In this commit the
mapping of device to driver data was mixed up. This results in the sam9x5
parameters being used for the sam9263 and the workaround for the broken mailbox
0 on the sam9263 not being activated.

This patch fixes the broken platform_device_id table.

Cc: linux-stable <stable@vger.kernel.org>
Cc: Ludovic Desroches <ludovic.desroches@atmel.com>
Signed-off-by: NMarc Kleine-Budde <mkl@pengutronix.de>

The current implemetation of of_match_device() relies that the of_device_id
table in the driver is sorted from most specific to least specific compatible.

Without this patch the mx28 is detected as the less specific p1010. This leads
to a p1010 specific workaround is activated on the mx28, which is not needed.

Cc: linux-stable <stable@vger.kernel.org>
Signed-off-by: NMarc Kleine-Budde <mkl@pengutronix.de>

In patch

    0d1862ea can: flexcan: fix flexcan_chip_start() on imx6

the loop in flexcan_chip_start() that iterates over all mailboxes after the
soft reset of the CAN core was removed. This loop put all mailboxes (even the
ones marked as reserved 1...7) into EMPTY/INACTIVE mode. On mailboxes 8...63,
this aborts any pending TX messages.

After a cold boot there is random garbage in the mailboxes, which leads to
spontaneous transmit of CAN frames during first activation. Further if the
interface was disabled with a pending message (usually due to an error
condition on the CAN bus), this message is retransmitted after enabling the
interface again.

This patch fixes the regression by:
1) Limiting the maximum number of used mailboxes to 8, 0...7 are used by the RX
FIFO, 8 is used by TX.
2) Marking the TX mailbox as EMPTY/INACTIVE, so that any pending TX of that
mailbox is aborted.

Cc: linux-stable <stable@vger.kernel.org>
Cc: Lothar Waßmann <LW@KARO-electronics.de>
Signed-off-by: NMarc Kleine-Budde <mkl@pengutronix.de>

John W. Linville says:

===================
Please pull this batch of fixes intended for 3.12...

Most of the bits are for iwlwifi -- Johannes says:

"I have a fix for WoWLAN/D3, a PCIe device fix, we're removing a
warning, there's a fix for RF-kill while scanning (which goes together
with a mac80211 fix) and last but not least we have many new PCI IDs."

Also for iwlwifi is a patch from Johannes to correct some merge damage
that crept into the tree before the last merge window.

On top of that, Felix Fietkau sends an ath9k patch to avoid a Tx
scheduling hang when changing channels to do a scan.
====================
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Merge in gianfar driver bug fixes from Claudiu Manoil.
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Enable workaround for P2020/P2010 erratum eTSEC 20,
"Excess delays when transmitting TOE=1 large frames".
The impact is that frames lager than 2500-bytes for which
TOE (i.e. TCP/IP hw accelerations like Tx csum) is enabled
may see excess delay before start of transmission.
This erratum was fixed in Rev 2.0.
Signed-off-by: NClaudiu Manoil <claudiu.manoil@freescale.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Use the macros and defines from mpc85xx.h to simplify
and prevent errors in identifying a mpc85xx based SoC
for errata detection.
This should help enabling (and identifying) workarounds
for various mpc85xx based chips and revisions.
For instance, express MPC8548 Rev.2 as:
(SVR_SOC_VER(svr) == SVR_8548) && (SVR_REV(svr) == 0x20)
instead of:
(pvr == 0x80210020 && mod == 0x8030 && rev == 0x0020)
Signed-off-by: NClaudiu Manoil <claudiu.manoil@freescale.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

A002 is still in "no plans to fix" state, and applies to all
the current P1/P2 parts as well, so it's resonable to enable
its workaround by default, for all the soc's with etsec.
The impact of not enabling this workaround for affected parts
is that under certain conditons (runt frames or even frames
with RX error detected at PHY level) during controller reset,
the controller might fail to indicate Rx reset (GRS) completion.
Signed-off-by: NClaudiu Manoil <claudiu.manoil@freescale.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Steffen Klassert says:

====================
1) We used the wrong netlink attribute to verify the
   lenght of the replay window on async events. Fix this by
   using the right netlink attribute.

2) Policy lookups can not match the output interface on forwarding.
   Add the needed informations to the flow informations.

3) We update the pmtu when we receive a ICMPV6_DEST_UNREACH message
   on IPsec with ipv6. This is wrong and leads to strange fragmented
   packets, only ICMPV6_PKT_TOOBIG messages should update the pmtu.
   Fix this by removing the ICMPV6_DEST_UNREACH check from the IPsec
   protocol error handlers.

4) The legacy IPsec anti replay mechanism supports anti replay
   windows up to 32 packets. If a user requests for a bigger
   anti replay window, we use 32 packets but pretend that we use
   the requested window size. Fix from Fan Du.

5) If asynchronous events are enabled and replay_maxdiff is set to
   zero, we generate an async event for every received packet instead
   of checking whether a timeout occurred. Fix from Thomas Egerer.

6) Policies need a refcount when the state resolution timer is armed.
   Otherwise the timer can fire after the policy is deleted.

7) We might dreference a NULL pointer if the hold_queue is empty,
   add a check to avoid this.
====================
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

net_secret() is only used when CONFIG_IPV6 or CONFIG_INET are selected.

Building a defconfig with both of these symbols unselected (Using the ARM
at91sam9rl_defconfig, for example) leads to the following build warning:

$ make at91sam9rl_defconfig
#
# configuration written to .config
#

$ make net/core/secure_seq.o
scripts/kconfig/conf --silentoldconfig Kconfig
  CHK     include/config/kernel.release
  CHK     include/generated/uapi/linux/version.h
  CHK     include/generated/utsrelease.h
make[1]: `include/generated/mach-types.h' is up to date.
  CALL    scripts/checksyscalls.sh
  CC      net/core/secure_seq.o
net/core/secure_seq.c:17:13: warning: 'net_secret_init' defined but not used [-Wunused-function]

Fix this warning by protecting the definition of net_secret() with these
symbols.
Reported-by: NOlof Johansson <olof@lixom.net>
Signed-off-by: NFabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Merge branch 'master' of git://git.kernel.org/pub/scm/linux/kernel/git/linville/wireless into for-davem

Ben Hutchings says:

====================
Some more fixes for EF10 support; hopefully the last lot:

1. Fixes for reading statistics, from Edward Cree and Jon Cooper.
2. Addition of ethtool statistics for packets dropped by the hardware
before they were associated with a specific function, from Edward Cree.
3. Only bind to functions that are in control of their associated port,
as the driver currently assumes this is the case.
====================
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Steinar reported FQ pacing was not working for UDP flows.

It looks like the initial sk->sk_pacing_rate value of 0 was
a wrong choice. We should init it to ~0U (unlimited)

Then, TCA_FQ_FLOW_DEFAULT_RATE should be removed because it makes
no real sense. The default rate is really unlimited, and we
need to avoid a zero divide.
Reported-by: NSteinar H. Gunderson <sesse@google.com>
Signed-off-by: NEric Dumazet <edumazet@google.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add the missing destroy_workqueue() before return from
qlcnic_probe() in the error handling case.
Signed-off-by: NWei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch fix the error handling in moxart_mac_probe():
 - return -ENOMEM in some memory alloc fail cases
 - add missing free_netdev() in the error handling case
Signed-off-by: NWei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch fixes the calculation of the nlmsg size, by adding the missing
nla_total_size().

Cc: Patrick McHardy <kaber@trash.net>
Signed-off-by: NMarc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

TCA_FQ_INITIAL_QUANTUM should set q->initial_quantum
Signed-off-by: NEric Dumazet <edumazet@google.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Unlike ipv4, the struct member hlen holds the length of the GRE and ipv6
headers. This length is also counted in dev->hard_header_len.
Perhaps, it's more clean to modify the hlen to count only the GRE header
without ipv6 header as the variable name suggest, but the simple way to fix
this without regression risk is simply modify the calculation of the limit
in ip6gre_tunnel_change_mtu function.
Verified in kernel version v3.11.
Signed-off-by: NOussama Ghorbel <ou.ghorbel@gmail.com>
Acked-by: NHannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

If a guest is destroyed without transitioning its frontend to CLOSED,
the domain becomes a zombie as netback was not grant unmapping the
shared rings.

When removing a VIF, transition the backend to CLOSED so the VIF is
disconnected if necessary (which will unmap the shared rings etc).

This fixes a regression introduced by
279f438e (xen-netback: Don't destroy
the netdev until the vif is shut down).
Signed-off-by: NDavid Vrabel <david.vrabel@citrix.com>
Cc: Ian Campbell <ian.campbell@citrix.com>
Cc: Wei Liu <wei.liu2@citrix.com>
Cc: Paul Durrant <Paul.Durrant@citrix.com>
Acked-by: NWei Liu <wei.liu2@citrix.com>
Reviewed-by: NPaul Durrant <paul.durrant@citrix.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Amir Vadai says:

====================
net/mlx4_en: Fix pages never dma unmapped on rx

This patchset fixes a bug introduced by commit 51151a16 (mlx4: allow order-0
memory allocations in RX path). Where dma_unmap_page wasn't called.

Changes from V0:
- Added "Rename name of mlx4_en_rx_alloc members". Old names were confusing.
- Last frag in page calculation was wrong. Since all frags in page are of the
  same size, need to add this frag_stride to end of frag offset, and not the
  size of next frag in skb.
====================
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch fixes a bug introduced by commit 51151a16 (mlx4: allow
order-0 memory allocations in RX path).

dma_unmap_page never reached because condition to detect last fragment
in page is wrong. offset+frag_stride can't be greater than size, need to
make sure no additional frag will fit in page => compare offset +
frag_stride + next_frag_size instead.
next_frag_size is the same as the current one, since page is shared only
with frags of the same size.

CC: Eric Dumazet <edumazet@google.com>
Signed-off-by: NAmir Vadai <amirv@mellanox.com>
Acked-by: NEric Dumazet <edumazet@google.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add page prefix to page related members: @size and @offset into
@page_size and @page_offset

CC: Eric Dumazet <edumazet@google.com>
Signed-off-by: NAmir Vadai <amirv@mellanox.com>
Acked-by: NEric Dumazet <edumazet@google.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch will fix RX packets errors when receiving big size
of data by set bit RNC = 1.

RNC - Receive Enable Control

0: Upon completion of reception of one frame, the E-DMAC writes
the receive status to the descriptor and clears the RR bit in
EDRRR to 0.

1: Upon completion of reception of one frame, the E-DMAC writes
(writes back) the receive status to the descriptor. In addition,
the E-DMAC reads the next descriptor and prepares for reception
of the next frame.

In addition, for get more stable when receiving packets, I set
maximum size for the transmit/receive FIFO and inserts padding
in receive data.
Signed-off-by: NNguyen Hong Ky <nh-ky@jinso.co.jp>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

net/l2tp/l2tp_core.c: In function ‘l2tp_verify_udp_checksum’:
net/l2tp/l2tp_core.c:499:22: warning: unused variable ‘tunnel’ [-Wunused-variable]

Create a helper "l2tp_tunnel()" to facilitate this, and as a side
effect get rid of a bunch of unnecessary void pointer casts.
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

We play with a wait queue even if socket is
non blocking. This is an obvious waste.
Besides, it will prevent calling the non blocking
variant when current is not valid.
Signed-off-by: NMichael S. Tsirkin <mst@redhat.com>
Acked-by: NJason Wang <jasowang@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Alan Ott says:

====================
Fix race conditions in mrf24j40 interrupts

After testing with the betas of this patchset, it's been rebased and is
ready for inclusion.

David Hauweele noticed that the mrf24j40 would hang arbitrarily after some
period of heavy traffic.  Two race conditions were discovered, and the
driver was changed to use threaded interrupts, since the enable/disable of
interrupts in the driver has recently been a lighning rod whenever issues
arise related to interrupts (costing engineering time), and since threaded
interrupts are the right way to do it.
====================
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The mrf24j40 generates level interrupts. There are rare cases where it
appears that the interrupt line never gets de-asserted between interrupts,
causing interrupts to be lost, and causing a hung device from the driver's
perspective.  Switching the driver to interpret these interrupts as
level-triggered fixes this issue.
Signed-off-by: NAlan Ott <alan@signal11.us>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Eliminate all the workqueue and interrupt enable/disable.
Signed-off-by: NAlan Ott <alan@signal11.us>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>