After connect command, send scan params WMI command to
set background scan period. If period value is zero
send 0xffff as bg scan period to disable bg scan.
Set default bg scan period to be 60 seconds if
not specified.

This patch depends on below patch
cfg80211: Add background scan period attribute.

kvalo: fix open parenthesis alignment
Signed-off-by: NBala Shanmugam <bkamatch@qca.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

In current code, Scan request info is recorded in vif->scan_req
after sending SCAN request to the firmware in ath6kl_cfg80211_scan().

In some corner cases, firmware sends SCAN_COMPLETE event immediately
when it receives SCAN request, which internally executes scan
complete event handler ath6kl_cfg80211_scan_complete_event() first.
So, Scan completion handler will a get a chance to executed even
before storing scan request info in ath6kl_cfg80211_scan().

Scan completion handler never report SCAN_COMPLETE event to
cfg80211 if scan request info(vif->scan_req) is NULL. This leads
to scan failure issue ("Device or resource busy error") during
next SCAN request from the user space. This patch ensures that scan
request info is stored before sending SCAN request.
Signed-off-by: NRaja Mani <rmani@qca.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

Configure the inactivity timeout passed in start_ap() to
firmware. This capability is advertised only when fw supports
it, there is a new bit (ATH6KL_FW_CAPABILITY_INACTIVITY_TIMEOUT)
in firmware capability ie for driver to learn fw's capability.
After the fw finds out the station is inactive, it will probe
the station with null func frames. By default, the timeout is
10 secs.
Signed-off-by: NVasanthakumar Thiagarajan <vthiagar@qca.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

Adding below steps helps to get good power numbers
in deep sleep suspend path,

    * Disable WOW mode.
    * Flush data packets and wait for all control packets.
      to be cleared in TX path before deep sleep suspend.
    * Set host sleep mode to SLEEP.

Below steps are added to perform the recovery action
while the system resume from deep sleep,

     * Set host sleep mode to AWAKE.
     * Reset scan parameters to default value.

In addition, Debug prints are added to track deep sleep
suspend/resume state.
Signed-off-by: NRaja Mani <rmani@qca.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

The piece of code used in ath6kk_wow_suspend function
to configure the host sleep mode is needed in deep sleep
case also.

Moving that portion to a separate function called
ath6kl_update_host_mode() would be helpful to avoid
the duplication of the same code in deep sleep path.

There is no functional change.

kvalo: move inline functions to cfg80211.c and fix a long line
Signed-off-by: NRaja Mani <rmani@qca.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

If the device disconnects from an AP when it is in suspending state. You will
get the following message from wpa_supplicant after waking the device up and
sending scan request:

"Scan trigger failed: ret=-16 (Device or resource busy)"

Fix the issue by sending a scan complete event before starting scheduled
scan.

kvalo: cosmetic changes to commit log
Signed-off-by: NIsaac.li <shonmou@gmail.com>
Tested-by: NRaja Mani <rmani@qca.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

When the device is in P2P GO mode and in listen state, the correct behavior is
to see two different probe response frames - one from P2P device and the other
from GO. wpa_supplicant uses the same mechanism to send the frame in both cases
(ath6kl_mgmt_tx). For GO probe response, ath6kl needs to call
ath6kl_send_go_probe_resp (this will add only WSC/P2P IEs and the rest of the
IEs are filled in by the firmware). That was done based on the nw_type ==
AP_NETWORK which would work if P2P Device role were in a separate netdev. When
P2P Device and GO use the same netdev, ath6kl needs to use the special GO probe
response case only if SSID is longer than P2P wildcard SSID.
Signed-off-by: NAarthi Thiruvengadam <athiruve@qca.qualcomm.com>
Reviewed-by: NJouni Malinen <jouni@qca.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

ath6kl/cfg80211.c:589: WARNING: max() should probably be
max_t(u16, vif->listen_intvl_t, ATH6KL_MAX_WOW_LISTEN_INTL)
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

Portion of the commit id 080eec4f ("ath6kl: Clear the IE in firmware
if not set") was overwritten by mistake due to a merge
conflict. This patch fixes the code back to how it should be.

kvalo: more details to the commit log
Signed-off-by: NAarthi Thiruvengadam <athiruve@qca.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

ath6kl/cfg80211.c:462: CHECK: Alignment should match open parenthesis
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

Found by checkpatch:

drivers/net/wireless/ath/ath6kl/cfg80211.c:1295: CHECK: multiple assignments should be avoided
drivers/net/wireless/ath/ath6kl/cfg80211.c:3000: CHECK: multiple assignments should be avoided
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

All found by checkpatch:

ath6kl/wmi.c:1036: CHECK: Logical continuations should be on the previous line
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

Fix the issues which checkpatch found and were easy to fix. Especially
callers of ath6kl_bmi_write() are tricky and that needs to be fixed
separately.
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

* In order to save the target power in WOW suspend state,
  configure the best optimal values for the below parameters,
     - listen interval.
     - beacon miss interval.
     - scan parameters.

  Default values for above attributes are reverted in
  wow resume operation.

* The default listen interval is set before the host issue
  connect request.

* New function is added to configure beacon miss count.

kvalo: minor changes to fix open parenthesis alignment
Signed-off-by: NRaja Mani <rmani@qca.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

Firmware has the option to support the listen interval
per vif specific. Fix this.

Listen interval can be set by the TUs or by the number
of beacons. Current code enables the user to configure
the listen interval in the unit of 'number of beacons'
using debugfs entry "listen_interval". Going forward,
we need to alter the listen interval in the unit of TUs
to get good power numbers while going to WOW suspend/resume.

Allowing the user to change the listen interval in
the unit of "number of beacons"  in debugfs and changing
listen interval in wow suspend/resume in the unit of
time (TUs) would lead us to confuse.

This patch make sures the listen interval is changed only
in the unit of time (TUs).
Signed-off-by: NRaja Mani <rmani@qca.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

Below two scenarios are taken care in this patch which helped
to fix the firmware crash during wow suspend/resume.

* TX operation (ctrl tx and data tx) has to be controlled based
  on suspend state. i.e, with respect to WOW mode, control packets
  are allowed to send from the host until the suspend state goes
  ATH6KL_STATE_WOW and the data packets are allowed until WOW
  suspend operation starts.

* Similarly, wow resume is NOT allowed if WOW suspend is in progress.
Signed-off-by: NRaja Mani <rmani@qca.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

It gives flexibility to the user to define suspend policy
when the suspend mode is set to WOW and the device is in
disconnected state at the time of suspend.

New module parameter wow_mode is added to get the choice
from the user. This parameter is valid only if the module
parameter suspend_mode is set to WOW.

To force WOW in connected state and cut power
in disconnected state:
  suspend_mode=0x3 wow_mode=0x1

To force WOW in connected state and deep sleep
in disconnected state (this is also the default wow_mode):
   suspend_mode=0x3 wow_mode=0x2

If there is no value specified to wow_mode during insmod,
deep sleep mode will be tried in the disconnected state.

kvalo: clarified commit log
Signed-off-by: NRaja Mani <rmani@qca.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

The ath6kl FW does not distinguish between different types of hidden
SSIDs (empty or null), so treat all cfg80211 requests for hidden ssid
the same.
Signed-off-by: NThomas Pedersen <c_tpeder@qca.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

Remove check so that IE in firmware is cleared if not set. Without this fix, any
previously set IE will be used incorrectly in the next frame. For example,
consider the scenario where a P2P device scan is followed by a regular station
scan. The P2P IE set by the P2P scan needs to be cleared, otherwise the station
scan will contain the P2P IE.

kvalo: indentation fixes
Signed-off-by: NAarthi Thiruvengadam <athiruve@qca.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

As regulatory events are processed even before the wiphy is registered,
calling regulatory_hint() at early stage should be fixed.
Signed-off-by: NVasanthakumar Thiagarajan <vthiagar@qca.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

There are some code which initializes various wiphy members
left outside ath6kl_cfg80211_init(), in ath6kl_core_init().
Move them into a single palce.
Signed-off-by: NVasanthakumar Thiagarajan <vthiagar@qca.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

Register driver's ht capabilities in wiphy to avoid failures
in setting ht channels from hostapd.
Signed-off-by: NVasanthakumar Thiagarajan <vthiagar@qca.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

This makes the device get into scan state as soon as a
scan request is received, instead of blocking the scan
request till the traffic comes down. It is  necessary
for the deterministic foreground scan particularly when
having multiple vif operating where, if the scan is non-
deterministic, scan on one interface will not start
as long as there are traffic on the other interface. This
change passes 50 msec as foreground scan interval to fix this.
Signed-off-by: NVasanthakumar Thiagarajan <vthiagar@qca.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

In ath6kl_cfg80211_add_key(), params is checked for non-NULL
but this pointer has been deferenced many times before this check. This
gives the following smatch warning. add_key() can never carry NULL as
params, remove this bogus check.

ath6kl_cfg80211_add_key(86) warn: variable dereferenced before check 'params'
Signed-off-by: NVasanthakumar Thiagarajan <vthiagar@qca.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

PS buffering of unicast Action frames that are sent in a context
of a BSS. In AP mode when the recepient station goes to powersave
and PS_POLL flag is not set, we would buffer the frames. Send out
unicast mgmt bufferred frame when PS_POLL is received.

This fixes a bug in P2P GO behavior when sending a GO Discoverability
Request to a client that is in sleep mode.

kvalo: indentation fixes
Signed-off-by: NThirumalai Pachamuthu <tpachamu@qca.qualcomm.com>
Signed-off-by: NNaveen Gangadharan <ngangadh@qca.qualcomm.com>
Signed-off-by: NAarthi Thiruvengadam <athiruve@qca.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

The AP/GO mode API isn't very clearly defined, it
has "set beacon" and "new beacon" etc.

Modify the API to the following:
 * start AP -- all settings
 * change beacon -- new beacon data
 * stop AP -- stop AP mode operation

This also reflects in the nl80211 API, rename
the commands there correspondingly (but keep
the old names for compatibility.)

Overall, this makes it much clearer what's going
on in the API.

Kalle developed the ath6kl changes, I created
the rest of the patch.
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Update license header with the copyright to Qualcomm Atheros, Inc.
for the year 2011-2012.
Signed-off-by: NVasanthakumar Thiagarajan <vthiagar@qca.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

Correct spelling "spported" to "supported" in
drivers/net/wireless/ath/ath6kl/cfg80211.c
Signed-off-by: NMasanari Iida <standby24x7@gmail.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

Error code ENOTCONN is more suitable than EINVAL to report
when the driver is not in connected state in ath6kl_wow_suspend().

I found this during code review.
Signed-off-by: NRaja Mani <rmani@qca.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

For every WMI_SET_HOST_SLEEP_MODE_CMDID command (send from the host),
the firmware sends WMI_SET_HOST_SLEEP_MODE_CMD_PROCESSED_EVENTID as
an acknowledgement to the host.

In order to being sync with the firmware, the host has to wait for
WMI_SET_HOST_SLEEP_MODE_CMD_PROCESSED_EVENT event before going to
the suspend state. This patch ensures ath6kl_wow_suspend() waits
until it gets this event after sending set host sleep mode command.

This patch adds,
 * New command WMI_SET_HOST_SLEEP_MODE_CMD_PROCESSED_EVENTID in
   WMI event table.
 * New WMI function ath6kl_wmi_host_sleep_mode_cmd_prcd_evt_rx()
   to process the event.
 * New flag HOST_SLEEP_MODE_CMD_PROCESSED in VIF flags to record
   the arrival of the event.
Signed-off-by: NRaja Mani <rmani@qca.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

First preference is given to the user configured WOW patterns.
If the user doesn't configure any patterns (for ex, via iw command),
the default patterns will be configured based on the current mode
(vif->nw_type) while going to WOW suspend.

Summary of changes:

  * ath6kl_wow_ap() is added to configure the below default
    patterns when the system enters into WOW suspend in AP mode.
      + Unicast IP, EAPOL-like and ARP packet pattern
      + ARP packet pattern
      + mDNS/SSDP/LLMNR pattern
      + DHCP broadcast pattern

 * ath6kl_wow_sta() is added to configure the below default
   patterns when the system enters into WOW suspend in STA mode.
      + Unicast packet pattern
      + mDNS/SSDP/LLMNR pattern

  * Move the user provided WOW patterns configuration code
    from ath6kl_wow_suspend() to a separate function called
    ath6kl_wow_usr().

  * Two argument variable's ('filter' and 'mask) data type in
    ath6kl_wmi_add_wow_pattern_cmd() are changed from 'u8 *' to
    'const u8 *'. This is needed to make all pattern and mask
    arrays to be 'static const u8' in the caller function.

  * New conditional check is added to make sure user
    configured pattern count is within the limit (WOW_MAX_FILTERS_PER_LIST).
Signed-off-by: NRaja Mani <rmani@qca.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

Currently rx aggregation related states are maintained per
vif, but this will not properly work when operating in AP mode.
Aggregation is completely broken when more than one
11n stations are connected to AP mode vif. Fix this issue
by keeping station specific aggregation state in sta_list.
Signed-off-by: NVasanthakumar Thiagarajan <vthiagar@qca.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

This patch just groups connection specific aggregation information
from struct aggr_info into a new structure (struct aggr_info_conn)
so that, in softAP mode, this can be used when each connected station
is made to have it's own aggregation state.
Signed-off-by: NVasanthakumar Thiagarajan <vthiagar@qca.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

Now ath6kl is ready for splitting core code to ath6kl_core.ko module.
This also makes it possible to link both sdio and usb code to kernel
at the same time, which earlier failed miserably.
Reported-by: NStephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

Currently core functions are spread between various files, group all
the functions into file and rename the functions to follow the style
used elsewhere in the driver. This will make it easier to a separate core
module.

Also fix a bug where wiphy is freed too early.
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

Group them together and change the naming to follow the common style in
ath6kl. No functional changes.
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

ath6kl_cfg80211_vif_init/cleanup() follow more closely the style used
elsewhere in ath6kl.
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

* A new APSD power save queue is added in the station structure.
* When a station has APSD capability and goes to power save, the frame
  designated to the station will be buffered in APSD queue.
* When the host receives a frame which the firmware marked as trigger,
  host delivers the buffered frame from the APSD power save queue.
  Number of frames to deliver is decided by MAX SP length.
* When a station moves from sleep to awake state, all frames buffered
  in APSD power save queue are sent to the firmware.
* When a station is disconnected, all frames bufferes in APSD power save
  queue are dropped.
* When the host queues the first frame to the APSD queue or removes the
  last frame from the APSD queue, it is indicated to the firmware using
  WMI_AP_APSD_BUFFERED_TRAFFIC_CMD.

kvalo: fix buggy handling of sks queues, made it more obvious
the user priority when wmm is disabled, remove unneed else block and
combined some variable declarations
Signed-off-by: NThirumalai Pachamuthu <tpachamu@qca.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

This patch addresses a few problems with the commit:

"ath6kl: Implement support for listen interval from userspace"

* The debugfs file required for reading/writing the listen interval
  wasn't created. Fix this.

* The interface index was being hardcoded to zero. Fix this.

* Two separate parameters, "listen_interval_time and listen_interval_beacons"
  were being used. This fails to work as expected because the FW assigns
  higher precedence to "listen_interval_beacons" and "listen_interval_time"
  ends up being never used at all.

  To handle this, fix the host driver to exclusively use listen interval
  based on units of beacon intervals.

To set the listen interval, a user would now do something like this:

echo "10" > /sys/kernel/debug/ieee80211/*/ath6kl/listen_interval

kvalo: fix two checkpatch warnings
Signed-off-by: NSujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

'params' is already used earlier and there is no point
in checking for a NULL condition again.
Signed-off-by: NSujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>