- 04 4月, 2013 4 次提交
-
-
由 Alexander Bondar 提交于
Current available FW still doesn't support new PM API. Therefore, to enable basic power management with the existing firmware, change the API in the driver back to the API used in the current firmware. Signed-off-by: NAlexander Bondar <alexander.bondar@intel.com> Reviewed-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com> Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
-
由 Emmanuel Grumbach 提交于
When we roam to A band, we don't need to constraint WiFi any more since it is operating on a different band. Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com> Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
-
由 Emmanuel Grumbach 提交于
This allows to have better wifi TPT when BT is active under good RSSI conditions. Wifi will have better chance to send Acks and Cts even if BT is active. Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com> Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
-
由 Johannes Berg 提交于
Use the per-interface debugfs infrastructure to create a directory and symlink, and add a file containing debug data related to each virtual interface. Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
-
- 26 3月, 2013 12 次提交
-
-
由 Emmanuel Grumbach 提交于
This caused issues with tracing as it's longer than the buffer size used there. Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com> Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
-
由 Emmanuel Grumbach 提交于
This module parameter isn't and won't be used. So ignore its value and set BT_CH_ANNOUNCE unconditionally. Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com> Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
-
由 Hauke Mehrtens 提交于
The BCM5354 SoC has a build in ieee80211 core rev 13 with a LP-PHY on it. This devices has a sprom version 3 stored in the nvram. This patch removes the warning and uses the opo values from the sprom as mentioned in the specs. Signed-off-by: NHauke Mehrtens <hauke@hauke-m.de> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Hauke Mehrtens 提交于
These attributes should be in the sprom for rev 2 and 3, but they were not read out. Signed-off-by: NHauke Mehrtens <hauke@hauke-m.de> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Hauke Mehrtens 提交于
With this patch the same registers are written, but this access is now protected by a lock. Signed-off-by: NHauke Mehrtens <hauke@hauke-m.de> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Rafał Miłecki 提交于
Signed-off-by: NRafał Miłecki <zajec5@gmail.com> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Rafał Miłecki 提交于
Signed-off-by: NRafał Miłecki <zajec5@gmail.com> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Yogesh Ashok Powar 提交于
Currently, default VHT configuration from the firmware is used for the VHT operations. Adding vhtcfg command to configure the firmware based on input received from cfg. Enable VHT for AP mode only when cfg80211_ap_settings has a VHT IE i.e., when ieee80211ac is set to 1 in the hostapd.conf. Signed-off-by: NYogesh Ashok Powar <yogeshp@marvell.com> Signed-off-by: NAvinash Patil <patila@marvell.com> Signed-off-by: NBing Zhao <bzhao@marvell.com> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Jussi Kivilinna 提交于
Add proper alignment at first packet copy, to avoid extra copies made later in networking stack. Signed-off-by: NJussi Kivilinna <jussi.kivilinna@iki.fi> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Jussi Kivilinna 提交于
Move processing of received packets to tasklet from hard-irq context. Signed-off-by: NJussi Kivilinna <jussi.kivilinna@iki.fi> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Jussi Kivilinna 提交于
RX path has extra copying of packets, that can be avoided. Signed-off-by: NJussi Kivilinna <jussi.kivilinna@iki.fi> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Jussi Kivilinna 提交于
Use dedicated DMA coherent buffers for RX urbs, to avoid allocation of large skbuffs in hard-irq context and improve performance. Signed-off-by: NJussi Kivilinna <jussi.kivilinna@iki.fi> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
- 25 3月, 2013 15 次提交
-
-
由 Luciano Coelho 提交于
Spin locks and completions are expensive in hard IRQ context and cause problems with RT kernels. In RT kernels, both spin locks and completions can schedule(), so we can't use them in hard irq context. Move handling code into the irq thread function to avoid that. Reported-by: NGregoire Gentil <gregoire@alwaysinnovating.com> Signed-off-by: NLuciano Coelho <coelho@ti.com>
-
由 Luciano Coelho 提交于
We were printing out all the hex dumps regardless of whether dynamic debugging was enabled or not. Now that print_hex_dump_debug() has been implemented, we can use that instead. Reported-by: NArik Nemtsov <arik@wizery.com> Signed-off-by: NLuciano Coelho <coelho@ti.com>
-
由 Arik Nemtsov 提交于
Don't ignore dummy packets when our queues are empty. This causes dummy packets never to be sent when traffic is not suspended by FW thresholds, which happens only in high Tx throughput situations. This may hurt Rx performance. Signed-off-by: NArik Nemtsov <arik@wizery.com> Signed-off-by: NLuciano Coelho <coelho@ti.com>
-
由 Arik Nemtsov 提交于
The wlcore state was checked without the mutex being taken. This leads to WARN_ONs sometimes if a notification arrives when the driver is on, but the mutex is only taken after it is off. This usually happens if stopping the driver while connected to a network. Signed-off-by: NArik Nemtsov <arik@wizery.com> Signed-off-by: NLuciano Coelho <coelho@ti.com>
-
由 Arik Nemtsov 提交于
Save the sequence number of the broadcast AP link in the wlvif. For each connected station, save the sequence number in the drv_priv part of ieee80211_sta. Use the saved numbers on recovery/resume, with the obligatory increment on recovery. Signed-off-by: NArik Nemtsov <arik@wizery.com> Signed-off-by: NLuciano Coelho <coelho@ti.com>
-
由 Arik Nemtsov 提交于
Dont use free_sta() on AP global links. It would fail an internal check within the function and various structures within the link struct would not be reset. Signed-off-by: NArik Nemtsov <arik@wizery.com> Signed-off-by: NLuciano Coelho <coelho@ti.com>
-
由 Victor Goldenshtein 提交于
Print board type, PG with metal and ROM versions. This might help debugging HW related issues. Signed-off-by: NVictor Goldenshtein <victorg@ti.com> Signed-off-by: NLuciano Coelho <coelho@ti.com>
-
由 Eyal Shapira 提交于
For STA we report beacon loss to higher levels so that wpa_s can attempt to roam without disconnecting. In case of P2P CLI we don't want to attempt roaming and instead disconnect immediately upon beacon loss. Signed-off-by: NEyal Shapira <eyal@wizery.com> Signed-off-by: NLuciano Coelho <coelho@ti.com>
-
由 Arik Nemtsov 提交于
On !CONFIG_SMP builds spin_is_locked always returns 0. Assert the locking using assert_spin_locked, which is written to behave correctly in all cases. Signed-off-by: NArik Nemtsov <arik@wizery.com> Signed-off-by: NLuciano Coelho <coelho@ti.com>
-
由 Nadim Zubidat 提交于
report the average beacon rssi which is calculated by firmware for roaming statistics instead of the last rx packet rssi. this results a more accurate rssi reporting Signed-off-by: NNadim Zubidat <nadimz@ti.com> Signed-off-by: NLuciano Coelho <coelho@ti.com>
-
由 Arik Nemtsov 提交于
Accumulate the total number of sent packets per-link to find out how far the encryption sequence number has progressed. Use this number as the initial security sequence number after recovery. This consolidates security sequence handling for both chip families, as we no longer have to rely on 12xx specific Tx completion. A fortunate side effect of this is correct management of seq numbers for AP roles and multi-role scenarios. When a link is removed we save the last seq number on a persistent part of the wlvif. This helps the data survive through recoveries/suspends, which also entail changes in the hlid of the link. This functionality is STA only currently. Signed-off-by: NArik Nemtsov <arik@wizery.com> Signed-off-by: NLuciano Coelho <coelho@ti.com>
-
由 Arik Nemtsov 提交于
The HLID of a STA can change, particularly during recovery. Don't cache the HLID before it was potentially allocated. Signed-off-by: NArik Nemtsov <arik@wizery.com> Signed-off-by: NLuciano Coelho <coelho@ti.com>
-
由 Arik Nemtsov 提交于
commit 144614f3eebd7d only allowed a single active link when turning on the optimization, ignoring the fact that an AP has two additional global links. Use 3 links as an indication for a single active link. Use the FW PSM bits to verify the extra active link belongs to the AP role. Signed-off-by: NArik Nemtsov <arik@wizery.com> Signed-off-by: NLuciano Coelho <coelho@ti.com>
-
由 Igal Chernobelsky 提交于
Maximum number of supported RX BA sessions depends on chip type. wl18xx supports 5 RX BA sessions while wl12xx supports 3. Signed-off-by: NIgal Chernobelsky <igalc@ti.com> Signed-off-by: NLuciano Coelho <coelho@ti.com>
-
由 Igal Chernobelsky 提交于
It is requiered to enter sleep mode with smaller delay in forced PS mode. This fixes issue of testing force PS mode during VoIP traffic where packets are sent every 20ms. Chip never enters ps mode with default 30 ms delay in such test. Signed-off-by: NIgal Chernobelsky <igalc@ti.com> Signed-off-by: NLuciano Coelho <coelho@ti.com>
-
- 20 3月, 2013 9 次提交
-
-
由 Ilan Peer 提交于
Schedule different time event based on the ROC type Signed-off-by: NIlan Peer <ilan.peer@intel.com> Reviewed-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com> Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
-
由 Ilan Peer 提交于
Increase the maximal remain on channel time as longer remain on channel requests are handled by the FW using fragmented time events. This reduces the number of user/kernel space iterations during flows such as p2p_listen. In addition it is currently required for flows which require longer duration such as p2p_sd. Signed-off-by: NIlan Peer <ilan.peer@intel.com> Reviewed-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com> Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
-
由 Johannes Berg 提交于
The RF-kill wakeup trigger flag is set in the wrong command, which means it won't work. Also fix the comment in the TCP wakeup trigger code -- the firmware was changed to look at all the different trigger flags. Reviewed-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com> Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
-
由 Emmanuel Grumbach 提交于
We should disable MIMO only if bt_traffic_load goes up to 3. Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com> Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
-
由 Emmanuel Grumbach 提交于
This is the right source of information for the valid Tx antennas, not the NVM. Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com> Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
-
由 Emmanuel Grumbach 提交于
This data should taken from TLVs and not from the NVM. This is true for the value written in CSR_HW_IF_CONFIG_REG too. Also, no need to set the CSR_HW_IF_CONFIG_REG_BIT_MAC_SI bit for 7000 devices which are the only devices currently supported. Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com> Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
-
由 Johannes Berg 提交于
In firmware "listener" (monitor) mode, we still need to open up the filters with the filter flags to receive all frames. Reviewed-by: NIlan Peer <ilan.peer@intel.com> Reviewed-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com> Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
-
由 Emmanuel Grumbach 提交于
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com> Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
-
由 Emmanuel Grumbach 提交于
This has valuable data about RFkill state seen from the fw side. Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com> Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
-