https://bugzilla.kernel.org/show_bug.cgi?id=86831

Markus reported that when shutting down mysqld (with AIO support,
on a ext3 formatted Harddrive) leads to a negative number of dirty pages
(underrun to the counter). The negative number results in a drastic reduction
of the write performance because the page cache is not used, because the kernel
thinks it is still 2 ^ 32 dirty pages open.

Add a warn trace in __dec_zone_state will catch this easily:

static inline void __dec_zone_state(struct zone *zone, enum
	zone_stat_item item)
{
     atomic_long_dec(&zone->vm_stat[item]);
+    WARN_ON_ONCE(item == NR_FILE_DIRTY &&
	atomic_long_read(&zone->vm_stat[item]) < 0);
     atomic_long_dec(&vm_stat[item]);
}

[   21.341632] ------------[ cut here ]------------
[   21.346294] WARNING: CPU: 0 PID: 309 at include/linux/vmstat.h:242
cancel_dirty_page+0x164/0x224()
[   21.355296] Modules linked in: wutbox_cp sata_mv
[   21.359968] CPU: 0 PID: 309 Comm: kworker/0:1 Not tainted 3.14.21-WuT #80
[   21.366793] Workqueue: events free_ioctx
[   21.370760] [<c0016a64>] (unwind_backtrace) from [<c0012f88>]
(show_stack+0x20/0x24)
[   21.378562] [<c0012f88>] (show_stack) from [<c03f8ccc>]
(dump_stack+0x24/0x28)
[   21.385840] [<c03f8ccc>] (dump_stack) from [<c0023ae4>]
(warn_slowpath_common+0x84/0x9c)
[   21.393976] [<c0023ae4>] (warn_slowpath_common) from [<c0023bb8>]
(warn_slowpath_null+0x2c/0x34)
[   21.402800] [<c0023bb8>] (warn_slowpath_null) from [<c00c0688>]
(cancel_dirty_page+0x164/0x224)
[   21.411524] [<c00c0688>] (cancel_dirty_page) from [<c00c080c>]
(truncate_inode_page+0x8c/0x158)
[   21.420272] [<c00c080c>] (truncate_inode_page) from [<c00c0a94>]
(truncate_inode_pages_range+0x11c/0x53c)
[   21.429890] [<c00c0a94>] (truncate_inode_pages_range) from
[<c00c0f6c>] (truncate_pagecache+0x88/0xac)
[   21.439252] [<c00c0f6c>] (truncate_pagecache) from [<c00c0fec>]
(truncate_setsize+0x5c/0x74)
[   21.447731] [<c00c0fec>] (truncate_setsize) from [<c013b3a8>]
(put_aio_ring_file.isra.14+0x34/0x90)
[   21.456826] [<c013b3a8>] (put_aio_ring_file.isra.14) from
[<c013b424>] (aio_free_ring+0x20/0xcc)
[   21.465660] [<c013b424>] (aio_free_ring) from [<c013b4f4>]
(free_ioctx+0x24/0x44)
[   21.473190] [<c013b4f4>] (free_ioctx) from [<c003d8d8>]
(process_one_work+0x134/0x47c)
[   21.481132] [<c003d8d8>] (process_one_work) from [<c003e988>]
(worker_thread+0x130/0x414)
[   21.489350] [<c003e988>] (worker_thread) from [<c00448ac>]
(kthread+0xd4/0xec)
[   21.496621] [<c00448ac>] (kthread) from [<c000ec18>]
(ret_from_fork+0x14/0x20)
[   21.503884] ---[ end trace 79c4bf42c038c9a1 ]---

The cause is that we set the aio ring file pages as *DIRTY* via SetPageDirty
(bypasses the VFS dirty pages increment) when init, and aio fs uses
*default_backing_dev_info* as the backing dev, which does not disable
the dirty pages accounting capability.
So truncating aio ring file will contribute to accounting dirty pages (VFS
dirty pages decrement), then error occurs.

The original goal is keeping these pages in memory (can not be reclaimed
or swapped) in life-time via marking it dirty. But thinking more, we have
already pinned pages via elevating the page's refcount, which can already
achieve the goal, so the SetPageDirty seems unnecessary.

In order to fix the issue, using the __set_page_dirty_no_writeback instead
of the nop .set_page_dirty, and dropped the SetPageDirty (don't manually
set the dirty flags, don't disable set_page_dirty(), rely on default behaviour).

With the above change, the dirty pages accounting can work well. But as we
known, aio fs is an anonymous one, which should never cause any real write-back,
we can ignore the dirty pages (write back) accounting by disabling the dirty
pages (write back) accounting capability. So we introduce an aio private
backing dev info (disabled the ACCT_DIRTY/WRITEBACK/ACCT_WB capabilities) to
replace the default one.
Reported-by: NMarkus Königshaus <m.koenigshaus@wut.de>
Signed-off-by: NGu Zheng <guz.fnst@cn.fujitsu.com>
Cc: stable <stable@vger.kernel.org>
Acked-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NBenjamin LaHaise <bcrl@kvack.org>

It seems that exit_aio() also needs to wait for all iocbs to complete (like
io_destroy), but we missed the wait step in current implemention, so fix
it in the same way as we did in io_destroy.
Signed-off-by: NGu Zheng <guz.fnst@cn.fujitsu.com>
Signed-off-by: NBenjamin LaHaise <bcrl@kvack.org>
Cc: stable@vger.kernel.org

We ran into a case on ppc64 running mariadb where io_getevents would
return zeroed out I/O events.  After adding instrumentation, it became
clear that there was some missing synchronization between reading the
tail pointer and the events themselves.  This small patch fixes the
problem in testing.

Thanks to Zach for helping to look into this, and suggesting the fix.
Signed-off-by: NJeff Moyer <jmoyer@redhat.com>
Signed-off-by: NBenjamin LaHaise <bcrl@kvack.org>
Cc: stable@vger.kernel.org

Pull x86 fixes from Ingo Molnar:
 "A couple of EFI fixes, plus misc fixes all around the map"

* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  efi/arm64: Store Runtime Services revision
  firmware: Do not use WARN_ON(!spin_is_locked())
  x86_32, entry: Clean up sysenter_badsys declaration
  x86/doc: Fix the 'tlb_single_page_flush_ceiling' sysconfig path
  x86/mm: Fix sparse 'tlb_single_page_flush_ceiling' warning and make the variable read-mostly
  x86/mm: Fix RCU splat from new TLB tracepoints

Pull perf fixes from Ingo Molnar:
 "A kprobes and a perf compat ioctl fix"

* 'perf-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  perf: Handle compat ioctl
  kprobes: Skip kretprobe hit in NMI context to avoid deadlock

Pull ARM SoC fixes from Olof Johansson:
 "A collection of fixes from this week, it's been pretty quiet and
  nothing really stands out as particularly noteworthy here -- mostly
  minor fixes across the field:

   - ODROID booting was fixed due to PMIC interrupts missing in DT
   - a collection of i.MX fixes
   - minor Tegra fix for regulators
   - Rockchip fix and addition of SoC-specific mailing list to make it
     easier to find posted patches"

* tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
  bus: arm-ccn: Fix warning message
  ARM: shmobile: koelsch: Remove non-existent i2c6 pinmux
  ARM: tegra: apalis/colibri t30: fix on-module 5v0 supplies
  MAINTAINERS: add new Rockchip SoC list
  ARM: dts: rockchip: readd missing mmc0 pinctrl settings
  ARM: dts: ODROID i2c improvements
  ARM: dts: Enable PMIC interrupts on ODROID
  ARM: dts: imx6sx: fix the pad setting for uart CTS_B
  ARM: dts: i.MX53: fix apparent bug in VPU clks
  ARM: imx: correct gpu2d_axi and gpu3d_axi clock setting
  ARM: dts: imx6: edmqmx6: change enet reset pin
  ARM: dts: vf610-twr: Fix pinctrl_esdhc1 pin definitions.
  ARM: imx: remove unnecessary ARCH_HAS_OPP select
  ARM: imx: fix TLB missing of IOMUXC base address during suspend
  ARM: imx6: fix SMP compilation again
  ARM: dt: sun6i: Add #address-cells and #size-cells to i2c controller nodes

Pull gpio fixes from Linus Walleij:

 - a largeish fix for the IRQ handling in the new Zynq driver.  The
   quite verbose commit message gives the exact details.
 - move some defines for gpiod flags outside an ifdef to make stub
   functions work again.
 - various minor fixes that we can accept for -rc1.

* tag 'gpio-v3.17-2' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio:
  gpio-lynxpoint: enable input sensing in resume
  gpio: move GPIOD flags outside #ifdef
  gpio: delete unneeded test before of_node_put
  gpio: zynq: Fix IRQ handlers
  gpiolib: devres: use correct structure type name in sizeof
  MAINTAINERS: Change maintainer for gpio-bcm-kona.c

Pull drm fixes from Dave Airlie:
 "Intel and radeon fixes.

  Post KS/LC git requests from i915 and radeon stacked up.  They are all
  fixes along with some new pci ids for radeon, and one maintainers file
  entry.

   - i915: display fixes and irq fixes
   - radeon: pci ids, and misc gpuvm, dpm and hdp cache"

* 'drm-fixes' of git://people.freedesktop.org/~airlied/linux: (29 commits)
  MAINTAINERS: Add entry for Renesas DRM drivers
  drm/radeon: add additional SI pci ids
  drm/radeon: add new bonaire pci ids
  drm/radeon: add new KV pci id
  Revert "drm/radeon: Use write-combined CPU mappings of ring buffers with PCIe"
  drm/radeon: fix active_cu mask on SI and CIK after re-init (v3)
  drm/radeon: fix active cu count for SI and CIK
  drm/radeon: re-enable selective GPUVM flushing
  drm/radeon: Sync ME and PFP after CP semaphore waits v4
  drm/radeon: fix display handling in radeon_gpu_reset
  drm/radeon: fix pm handling in radeon_gpu_reset
  drm/radeon: Only flush HDP cache for indirect buffers from userspace
  drm/radeon: properly document reloc priority mask
  drm/i915: don't try to retrain a DP link on an inactive CRTC
  drm/i915: make sure VDD is turned off during system suspend
  drm/i915: cancel hotplug and dig_port work during suspend and unload
  drm/i915: fix HPD IRQ reenable work cancelation
  drm/i915: take display port power domain in DP HPD handler
  drm/i915: Don't try to enable cursor from setplane when crtc is disabled
  drm/i915: Skip load detect when intel_crtc->new_enable==true
  ...

As reported by Dan Aloni, commit f8567a38 ("aio: fix aio request
leak when events are reaped by userspace") introduces a regression when
user code attempts to perform io_submit() with more events than are
available in the ring buffer.  Reverting that commit would reintroduce a
regression when user space event reaping is used.

Fixing this bug is a bit more involved than the previous attempts to fix
this regression.  Since we do not have a single point at which we can
count events as being reaped by user space and io_getevents(), we have
to track event completion by looking at the number of events left in the
event ring.  So long as there are as many events in the ring buffer as
there have been completion events generate, we cannot call
put_reqs_available().  The code to check for this is now placed in
refill_reqs_available().

A test program from Dan and modified by me for verifying this bug is available
at http://www.kvack.org/~bcrl/20140824-aio_bug.c .
Reported-by: NDan Aloni <dan@kernelim.com>
Signed-off-by: NBenjamin LaHaise <bcrl@kvack.org>
Acked-by: NDan Aloni <dan@kernelim.com>
Cc: Kent Overstreet <kmo@daterainc.com>
Cc: Mateusz Guzik <mguzik@redhat.com>
Cc: Petr Matousek <pmatouse@redhat.com>
Cc: stable@vger.kernel.org      # v3.16 and anything that f8567a38 was backported to
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

A message warning a user about wrong vc value was printing
out port instead.
Reported-by: NDrew Richardson <drew.richardson@arm.com>
Signed-off-by: NPawel Moll <pawel.moll@arm.com>
Signed-off-by: NOlof Johansson <olof@lixom.net>

On r8a7791, i2c6 (aka iic3) doesn't need pinmux, but the koelsch dts
refers to non-existent pinmux configuration data:

pinmux core: sh-pfc does not support function i2c6
sh-pfc e6060000.pfc: invalid function i2c6 in map table

Remove it to fix this.

Fixes: commit 1d41f36a ("ARM: shmobile:
       koelsch dts: Add VDD MPU regulator for DVFS")
Signed-off-by: NGeert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: NSimon Horman <horms+renesas@verge.net.au>
Signed-off-by: NOlof Johansson <olof@lixom.net>

Working on Gigabit/PCIe support in U-Boot for Apalis T30 I realised
that the current device tree source includes for our modules only
happen to work due to referencing the on-carrier 5v0 supply from USB
which is not at all available on-module. The modules actually contain
TPS60150 charge pumps to generate the PMIC required 5 volts from the
one and only 3.3 volt module supply. This patch fixes this.

(Note: When back-porting this to v3.16 stable releases, simply drop the
change to tegra30-apalis.dtsi; that file was added in v3.17)

Cc: <stable@vger.kernel.org> #v3.16+
Signed-off-by: NMarcel Ziswiler <marcel@ziswiler.com>
Signed-off-by: NStephen Warren <swarren@nvidia.com>
Signed-off-by: NOlof Johansson <olof@lixom.net>

Merge tag 'v3.17-rockchip-fixes1' of git://git.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip into fixes

Merge "ARM: rockchip: fix for 3.17" from Heiko Stubner:

Pinctrl that got accidentially dropped when reorganizing the
dts files and addition of the new Rockchip list to MAINTAINERS.

* tag 'v3.17-rockchip-fixes1' of git://git.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip:
  MAINTAINERS: add new Rockchip SoC list
  ARM: dts: rockchip: readd missing mmc0 pinctrl settings
Signed-off-by: NOlof Johansson <olof@lixom.net>

Signed-off-by: NLaurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: NDave Airlie <airlied@gmail.com>

This pull just contains some new pci ids.

* 'drm-fixes-3.17' of git://people.freedesktop.org/~agd5f/linux:
  drm/radeon: add additional SI pci ids
  drm/radeon: add new bonaire pci ids
  drm/radeon: add new KV pci id

Add the new list that Rockchip-specific patches should also be directed to.
Signed-off-by: NHeiko Stuebner <heiko@sntech.de>

During the restructuring of the Rockchip Cortex-A9 dtsi files it seems
like the pinctrl settings vanished at some point from the mmc0 support.

This of course renders them unusable, so readd the necessary pinctrl
properties.
Signed-off-by: NHeiko Stuebner <heiko@sntech.de>

Merge tag 'sunxi-dt-for-3.17-2' of git://git.kernel.org/pub/scm/linux/kernel/git/mripard/linux into fixes

Merge "Allwinner DT changes, take 2" from Maxime Ripard:

Only a single patch in here that fixes a DTC warning.

* tag 'sunxi-dt-for-3.17-2' of git://git.kernel.org/pub/scm/linux/kernel/git/mripard/linux:
  ARM: dt: sun6i: Add #address-cells and #size-cells to i2c controller nodes
Signed-off-by: NOlof Johansson <olof@lixom.net>

Merge tag 'pwm/for-3.17-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/thierry.reding/linux-pwm

Pull pwm fix from Thierry Reding:
 "Just one bugfix for the PWM lookup table code that would cause a PWM
  channel to be set to the wrong period and polarity for non-perfect
  matches"

* tag 'pwm/for-3.17-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/thierry.reding/linux-pwm:
  pwm: Fix period and polarity in pwm_get() for non-perfect matches

The new_ctx pointer is set only for non-chanctx drivers.  This yielded a
crash for chanctx-based drivers during channel switch finalization:

  BUG: unable to handle kernel NULL pointer dereference at 0000000000000020
  IP: ieee80211_vif_use_reserved_switch+0x71c/0xb00 [mac80211]

Use an adequate chanctx pointer to fix this.
Reported-by: NLinus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: NMichal Kazior <michal.kazior@tieto.com>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Pull networking fixes from David Miller:
 "Here are some bug fixes that have piled up during ksummit/linuxcon.

   1) Fix endian problems in ibmveth, from Anton Blanchard.

   2) IPV6 routing code does GFP_KERNEL allocation in atomic, fix from
      Benjamin Block.

   3) SCTP association fixes from Daniel Borkmann.

   4) When multiple VLAN headers are present we have to make sure the
      second and subsequent ones are pullable in the SKB otherwise we
      blindly dereference garbage.  From Jiri Benc.

   5) The argument adjustment of the signature of hlist_add_after*()
      introduced a regression in the batman-adv code, fix from Sven
      Eckelmann.

   6) Fix TX hang handling to avoid a panic in i40e, from Anjali Singhai
      Jain.

   7) PTP flag test is inverted in i40e driver, from Jesse Brandeburg.

   8) ATM LEC driver needs to hold RTNL mutex over MTU changes, from
      Chas Williams.

   9) Truncate packets larger then the TPACKET_V3 format configured
      buffers, otherwise we overwrite past the end of said buffers.
      From Eric Dumazet.

  10) Fix endianness bugs in qlcnic firmware handling, from Rajesh
      Borundia and Shahed Shaikh.

  11) CXGB4 sometimes doesn't get all of the TX completion events it
      should resulting in SKBs getting stuck in the TX queue, from
      Hariprasad Shenai.

  12) When the FEC chip's PTP clock is disabled, you can't access the
      register.  Add necessary checks to avoid the resulting hang, from
      Fugang Duan"

* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (37 commits)
  drivers: isdn: eicon: xdi_msg.h: Fix typo in #ifndef
  net: sctp: fix suboptimal edge-case on non-active active/retrans path selection
  net: sctp: spare unnecessary comparison in sctp_trans_elect_best
  net: ethernet: broadcom: bnx2x: Remove redundant #ifdef
  ibmveth: Fix endian issues with rx_no_buffer statistic
  net: xgene: fix possible NULL dereference in xgene_enet_free_desc_rings()
  openvswitch: fix panic with multiple vlan headers
  net: ipv6: fib: don't sleep inside atomic lock
  net: fec: ptp: avoid register access when ipg clock is disabled
  cxgb4: Free completed tx skbs promptly
  cxgb4: Fix race condition in cleanup
  sctp: not send SCTP_PEER_ADDR_CHANGE notifications with failed probe
  bnx2x: Revert UNDI flushing mechanism
  qlcnic: Fix endianess issue in firmware load from file operation
  qlcnic: Fix endianess issue in FW dump template header
  qlcnic: Fix flash access interface to application
  MAINTAINERS: Add section for MRF24J40 IEEE 802.15.4 radio driver
  macvlan: Allow setting multicast filter on all macvlan types
  packet: handle too big packets for PACKET_V3
  MAINTAINERS: add entry for ec_bhf driver
  ...

Test for definedness of the macro which is actually defined (the
change is hard to see: it is s/SSS/SSA/).
Signed-off-by: NRasmus Villemoes <linux@rasmusvillemoes.dk>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

In SCTP, selection of active (T.ACT) and retransmission (T.RET)
transports is being done whenever transport control operations
(UP, DOWN, PF, ...) are engaged through sctp_assoc_control_transport().

Commits 4c47af4d ("net: sctp: rework multihoming retransmission
path selection to rfc4960") and a7288c4d ("net: sctp: improve
sctp_select_active_and_retran_path selection") have both improved
it towards a more fine-grained and optimal path selection.

Currently, the selection algorithm for T.ACT and T.RET is as follows:

1) Elect the two most recently used ACTIVE transports T1, T2 for
   T.ACT, T.RET, where T.ACT<-T1 and T1 is most recently used
2) In case primary path T.PRI not in {T1, T2} but ACTIVE, set
   T.ACT<-T.PRI and T.RET<-T1
3) If only T1 is ACTIVE from the set, set T.ACT<-T1 and T.RET<-T1
4) If none is ACTIVE, set T.ACT<-best(T.PRI, T.RET, T3) where
   T3 is the most recently used (if avail) in PF, set T.RET<-T.PRI

Prior to above commits, 4) was simply a camp on T.ACT<-T.PRI and
T.RET<-T.PRI, ignoring possible paths in PF. Camping on T.PRI is
still slightly suboptimal as it can lead to the following scenario:

Setup:
        <A>                                <B>
    T1: p1p1 (10.0.10.10) <==>  .'`)  <==> p1p1 (10.0.10.12)  <= T.PRI
    T2: p1p2 (10.0.10.20) <==> (_ . ) <==> p1p2 (10.0.10.22)

    net.sctp.rto_min = 1000
    net.sctp.path_max_retrans = 2
    net.sctp.pf_retrans = 0
    net.sctp.hb_interval = 1000

T.PRI is permanently down, T2 is put briefly into PF state (e.g. due to
link flapping). Here, the first time transmission is sent over PF path
T2 as it's the only non-INACTIVE path, but the retransmitted data-chunks
are sent over the INACTIVE path T1 (T.PRI), which is not good.

After the patch, it's choosing better transports in both cases by
modifying step 4):

4) If none is ACTIVE, set T.ACT_new<-best(T.ACT_old, T3) where T3 is
   the most recently used (if avail) in PF, set T.RET<-T.ACT_new

This will still select a best possible path in PF if available (which
can also include T.PRI/T.RET), and set both T.ACT/T.RET to it.

In case sctp_assoc_control_transport() *just* put T.ACT_old into INACTIVE
as it transitioned from ACTIVE->PF->INACTIVE and stays in INACTIVE just
for a very short while before going back ACTIVE, it will guarantee that
this path will be reselected for T.ACT/T.RET since T3 (PF) is not
available.

Previously, this was not possible, as we would only select between T.PRI
and T.RET, and a possible T3 would be NULL due to the fact that we have
just transitioned T3 in sctp_assoc_control_transport() from PF->INACTIVE
and would select a suboptimal path when T.PRI/T.RET have worse properties.

In the case that T.ACT_old permanently went to INACTIVE during this
transition and there's no PF path available, plus T.PRI and T.RET are
INACTIVE as well, we would now camp on T.ACT_old, but if everything is
being INACTIVE there's really not much we can do except hoping for a
successful HB to bring one of the transports back up again and, thus
cause a new selection through sctp_assoc_control_transport().

Now both tests work fine:

Case 1:

 1. T1 S(ACTIVE) T.ACT
    T2 S(ACTIVE) T.RET

 2. T1 S(ACTIVE) T.ACT, T.RET
    T2 S(PF)

 3. T1 S(ACTIVE) T.ACT, T.RET
    T2 S(INACTIVE)

 5. T1 S(PF) T.ACT, T.RET
    T2 S(INACTIVE)

[ 5.1 T1 S(INACTIVE) T.ACT, T.RET
      T2 S(INACTIVE) ]

 6. T1 S(ACTIVE) T.ACT, T.RET
    T2 S(INACTIVE)

 7. T1 S(ACTIVE) T.ACT
    T2 S(ACTIVE) T.RET

Case 2:

 1. T1 S(ACTIVE) T.ACT
    T2 S(ACTIVE) T.RET

 2. T1 S(PF)
    T2 S(ACTIVE) T.ACT, T.RET

 3. T1 S(INACTIVE)
    T2 S(ACTIVE) T.ACT, T.RET

 5. T1 S(INACTIVE)
    T2 S(PF) T.ACT, T.RET

[ 5.1 T1 S(INACTIVE)
      T2 S(INACTIVE) T.ACT, T.RET ]

 6. T1 S(INACTIVE)
    T2 S(ACTIVE) T.ACT, T.RET

 7. T1 S(ACTIVE) T.ACT
    T2 S(ACTIVE) T.RET
Signed-off-by: NDaniel Borkmann <dborkman@redhat.com>
Acked-by: NNeil Horman <nhorman@tuxdriver.com>
Acked-by: NVlad Yasevich <vyasevich@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When both transports are the same, we don't have to go down that
road only to realize that we will return the very same transport.
We are guaranteed that curr is always non-NULL. Therefore, just
short-circuit this special case.
Signed-off-by: NDaniel Borkmann <dborkman@redhat.com>
Acked-by: NNeil Horman <nhorman@tuxdriver.com>
Acked-by: NVlad Yasevich <vyasevich@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Nothing defines _ASM_GENERIC_INT_L64_H, it is a weird way to check for
64 bit longs, and u64 should be printed using %llx anyway.
Signed-off-by: NRasmus Villemoes <linux@rasmusvillemoes.dk>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Hidden away in the last 8 bytes of the buffer_list page is a solitary
statistic. It needs to be byte swapped or else ethtool -S will
produce numbers that terrify the user.

Since we do this in multiple places, create a helper function with a
comment explaining what is going on.
Signed-off-by: NAnton Blanchard <anton@samba.org>
Cc: stable@vger.kernel.org
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

A NULL pointer dereference is possible for the argument ring->buf_pool
which is passed to xgene_enet_free_desc_ring(), as ring could be NULL.

And now since NULL pointers are being checked for before the calls to
xgene_enet_free_desc_ring(), might as well take advantage of them and
not call the function if the argument would be NULL.
Reported-by: NDan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: NIyappan Subramanian <isubramanian@apm.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When there are multiple vlan headers present in a received frame, the first
one is put into vlan_tci and protocol is set to ETH_P_8021Q. Anything in the
skb beyond the VLAN TPID may be still non-linear, including the inner TCI
and ethertype. While ovs_flow_extract takes care of IP and IPv6 headers, it
does nothing with ETH_P_8021Q. Later, if OVS_ACTION_ATTR_POP_VLAN is
executed, __pop_vlan_tci pulls the next vlan header into vlan_tci.

This leads to two things:

1. Part of the resulting ethernet header is in the non-linear part of the
   skb. When eth_type_trans is called later as the result of
   OVS_ACTION_ATTR_OUTPUT, kernel BUGs in __skb_pull. Also, __pop_vlan_tci
   is in fact accessing random data when it reads past the TPID.

2. network_header points into the ethernet header instead of behind it.
   mac_len is set to a wrong value (10), too.
Reported-by: NYulong Pei <ypei@redhat.com>
Signed-off-by: NJiri Benc <jbenc@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The function fib6_commit_metrics() allocates a piece of memory in mode
GFP_KERNEL while holding an atomic lock from higher up in the stack, in
the function __ip6_ins_rt(). This produces the following BUG:

> BUG: sleeping function called from invalid context at mm/slub.c:1250
> in_atomic(): 1, irqs_disabled(): 0, pid: 2909, name: dhcpcd
> 2 locks held by dhcpcd/2909:
>  #0:  (rtnl_mutex){+.+.+.}, at: [<ffffffff81978e67>] rtnl_lock+0x17/0x20
>  #1:  (&tb->tb6_lock){++--+.}, at: [<ffffffff81a6951a>] ip6_route_add+0x65a/0x800
> CPU: 1 PID: 2909 Comm: dhcpcd Not tainted 3.17.0-rc1 #1
> Hardware name: ASUS All Series/Q87T, BIOS 0216 10/16/2013
>  0000000000000008 ffff8800c8f13858 ffffffff81af135a 0000000000000000
>  ffff880212202430 ffff8800c8f13878 ffffffff810f8d3a ffff880212202c98
>  0000000000000010 ffff8800c8f138c8 ffffffff8121ad0e 0000000000000001
> Call Trace:
>  [<ffffffff81af135a>] dump_stack+0x4e/0x68
>  [<ffffffff810f8d3a>] __might_sleep+0x10a/0x120
>  [<ffffffff8121ad0e>] kmem_cache_alloc_trace+0x4e/0x190
>  [<ffffffff81a6bcd6>] ? fib6_commit_metrics+0x66/0x110
>  [<ffffffff81a6bcd6>] fib6_commit_metrics+0x66/0x110
>  [<ffffffff81a6cbf3>] fib6_add+0x883/0xa80
>  [<ffffffff81a6951a>] ? ip6_route_add+0x65a/0x800
>  [<ffffffff81a69535>] ip6_route_add+0x675/0x800
>  [<ffffffff81a68f2a>] ? ip6_route_add+0x6a/0x800
>  [<ffffffff81a6990c>] inet6_rtm_newroute+0x5c/0x80
>  [<ffffffff8197cf01>] rtnetlink_rcv_msg+0x211/0x260
>  [<ffffffff81978e67>] ? rtnl_lock+0x17/0x20
>  [<ffffffff81119708>] ? lock_release_holdtime+0x28/0x180
>  [<ffffffff81978e67>] ? rtnl_lock+0x17/0x20
>  [<ffffffff8197ccf0>] ? __rtnl_unlock+0x20/0x20
>  [<ffffffff819a989e>] netlink_rcv_skb+0x6e/0xd0
>  [<ffffffff81978ee5>] rtnetlink_rcv+0x25/0x40
>  [<ffffffff819a8e59>] netlink_unicast+0xd9/0x180
>  [<ffffffff819a9600>] netlink_sendmsg+0x700/0x770
>  [<ffffffff81103735>] ? local_clock+0x25/0x30
>  [<ffffffff8194e83c>] sock_sendmsg+0x6c/0x90
>  [<ffffffff811f98e3>] ? might_fault+0xa3/0xb0
>  [<ffffffff8195ca6d>] ? verify_iovec+0x7d/0xf0
>  [<ffffffff8194ec3e>] ___sys_sendmsg+0x37e/0x3b0
>  [<ffffffff8111ef15>] ? trace_hardirqs_on_caller+0x185/0x220
>  [<ffffffff81af979e>] ? mutex_unlock+0xe/0x10
>  [<ffffffff819a55ec>] ? netlink_insert+0xbc/0xe0
>  [<ffffffff819a65e5>] ? netlink_autobind.isra.30+0x125/0x150
>  [<ffffffff819a6520>] ? netlink_autobind.isra.30+0x60/0x150
>  [<ffffffff819a84f9>] ? netlink_bind+0x159/0x230
>  [<ffffffff811f989a>] ? might_fault+0x5a/0xb0
>  [<ffffffff8194f25e>] ? SYSC_bind+0x7e/0xd0
>  [<ffffffff8194f8cd>] __sys_sendmsg+0x4d/0x80
>  [<ffffffff8194f912>] SyS_sendmsg+0x12/0x20
>  [<ffffffff81afc692>] system_call_fastpath+0x16/0x1b

Fixing this by replacing the mode GFP_KERNEL with GFP_ATOMIC.
Signed-off-by: NBenjamin Block <bebl@mageta.org>
Acked-by: NDavid Rientjes <rientjes@google.com>
Acked-by: NHannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The current kernel hang on i.MX6SX with rootfs mount from MMC.
The root cause is that ptp uses a periodic timer to access enet register
even if ipg clock is disabled.

FEC ptp driver start one period timer to read 1588 counter register in the
ptp init function that is called after FEC driver is probed.

To save power, after FEC probe finish, FEC driver disable all clocks including
ipg clock that is needed for register access.

i.MX5x, i.MX6q/dl/sl FEC register access don't cause system hang when ipg clock
is disabled, just return zero value. But for i.MX6sx SOC, it cause system hang.

To avoid the issue, we need to check ptp clock status before ptp timer count access.
Signed-off-by: NFugang Duan <B38611@freescale.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Pull arm64 fixes from Will Deacon:
 "This small set of fixes addresses a few issues introduced during the
  merge window, including:

   - fix typo in I-cache detection that was causing us to treat all
     I-caches as aliasing
   - hook up memfd_create and getrandom syscalls for native and compat
   - revert a temporary hack for defconfig builds in -next (the audit
     tree changes didn't make it in this merge window)
   - a couple of UEFI fixes for TEXT_OFFSET fuzzing and /memreserve/
   - a simple sparsemem fix for 48-bit physical addressing
   - small defconfig updates to get autotesters working with X-gene"

* tag 'arm64-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux:
  Revert "arm64: Do not invoke audit_syscall_* functions if !CONFIG_AUDIT_SYSCALL"
  arm64: mm: update max pa bits to 48
  arm64: ignore DT memreserve entries when booting in UEFI mode
  arm64: configs: Enable X-Gene SATA and ethernet in defconfig
  arm64: align randomized TEXT_OFFSET on 4 kB boundary
  asm-generic: add memfd_create system call to unistd.h
  arm64: compat: wire up memfd_create and getrandom syscalls for aarch32
  arm64: fix typo in I-cache policy detection

Pull IOMMU fixes from Joerg Roedel:
 "The fixes include:

   - fix a crash in the VT-d driver when devices with a driver attached
     are hot-unplugged

   - fix a AMD IOMMU driver crash with device assignment of 32 bit PCI
     devices to KVM guests

   - fix for a copy&paste error in generic IOMMU code.  Now the right
     function pointer is checked before calling"

* tag 'iommu-fixes-v3.17-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/joro/iommu:
  iommu/core: Check for the right function pointer in iommu_map()
  iommu/amd: Fix cleanup_domain for mass device removal
  iommu/vt-d: Defer domain removal if device is assigned to a driver

Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org

Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org

bug:
https://bugs.freedesktop.org/show_bug.cgi?id=82912Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org

Merge tag 'efi-urgent' of git://git.kernel.org/pub/scm/linux/kernel/git/mfleming/efi into x86/urgent

Pull EFI fixes from Matt Fleming:

 * WARN_ON(!spin_is_locked()) always triggers on non-SMP machines.
   Swap it for the more canonical lockdep_assert_held() which always
   does the right thing - Guenter Roeck

 * Assign the correct value to efi.runtime_version on arm64 so that all
   the runtime services can be invoked - Semen Protsenko
Signed-off-by: NIngo Molnar <mingo@kernel.org>

"efi" global data structure contains "runtime_version" field which must
be assigned in order to use it later in Runtime Services virtual calls
(virt_efi_* functions).

Before this patch "runtime_version" was unassigned (0), so each
Runtime Service virtual call that checks revision would fail.
Signed-off-by: NSemen Protsenko <semen.protsenko@linaro.org>
Acked-by: NArd Biesheuvel <ard.biesheuvel@linaro.org>
Cc: <stable@vger.kernel.org>
Signed-off-by: NMatt Fleming <matt.fleming@intel.com>

spin_is_locked() always returns false for uniprocessor configurations
in several architectures, so do not use WARN_ON with it.
Use lockdep_assert_held() instead to also reduce overhead in
non-debug kernels.
Signed-off-by: NGuenter Roeck <linux@roeck-us.net>
Cc: <stable@vger.kernel.org>
Signed-off-by: NMatt Fleming <matt.fleming@intel.com>

Description of problem:
The NIC card is not reporting back to the driver the transmitted skbs,
so they get stuck in the TX ring causing issues with reference
counters in other kernel components.

Developed a new Automatic Egress Queue Update firmware facility to slowly tick
through Egress Queues and send back any outstanding CIDX Updates which are
laying around.

Based on original work by Casey Leedom <leedom@chelsio.com>
Signed-off-by: NHariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Marc Kleine-Budde says:

====================
pull-request: can 2014-08-21

The first patch is from Mirza Krak, it fixes the initialization of the hardware
in the sja1000 driver. The next patch is contributed by Dan Carpenter, it fixes
the error handling in the c_can's probe function. Then there are two patches
for the flexcan driver, one by Alexander Stein, which fixes the resetting of
the bus error interrupt mask, the other one by Sebastian Andrzej Siewior which
adds an additional error state transition message.
====================
Signed-off-by: NDavid S. Miller <davem@davemloft.net>