Previously, only basic rates were used for data transmission - resulting in
reduced transfer rates. This patch takes enables the firmware to take advantage
of the full set of data rates supported by the AP.
Signed-off-by: NJuuso Oikarinen <juuso.oikarinen@nokia.com>
Reviewed-by: NLuciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: NLuciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Previously a "firmware chooses" value was used for the rates of all control
message templates set to the firmware. This resulted in a too high rate to be
chosen to transmit those messages. Change this by configuring a fixed low rate
for the templates.
Signed-off-by: NJuuso Oikarinen <juuso.oikarinen@nokia.com>
Reviewed-by: NLuciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: NLuciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This patch adds rudimentary a-hoc support for the driver. It will allow
setting up ad-hoc, and for other devices to scan and join. The beacon and probe
response template setting is slightly dirty, and need to be properly
implemented with support from mac80211. Also, the SSID is not configured to the
firmware - the FW will not be able to respond to probe requests autonomously.
Signed-off-by: NJuuso Oikarinen <juuso.oikarinen@nokia.com>
Reviewed-by: NLuciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: NLuciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Remove the beacon-loss indication to stack from PSM entry failure handling -
this will cause more problems than it will solve due to the design of the
mac80211.
Signed-off-by: NJuuso Oikarinen <juuso.oikarinen@nokia.com>
Reviewed-by: NLuciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: NLuciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This patch adds a short delay before powering on the wl1271. Normally, it is
not needed, but if the wl1271 has been powered off shortly before, for reliable
firmware-booting this small stabilization delay is required.
Signed-off-by: NJuuso Oikarinen <juuso.oikarinen@nokia.com>
Reviewed-by: NLuciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: NLuciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The wl1271 has a hardware bug which causes it to randomly (very infrequently)
to fail powering up properly. This patch implements retry for the chipset boot
sequence, to work around the hardware problem.
Signed-off-by: NJuuso Oikarinen <juuso.oikarinen@nokia.com>
Reviewed-by: NLuciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: NLuciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The mac80211 sometimes requests power save entry while not associated - this
will cause problems, so prevent it if not associated. Go to powersave once
association is complete.
Signed-off-by: NJuuso Oikarinen <juuso.oikarinen@nokia.com>
Reviewed-by: NLuciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: NLuciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

In reference source, events are acknowledged separately - fix the driver to
do the same.
Signed-off-by: NJuuso Oikarinen <juuso.oikarinen@nokia.com>
Reviewed-by: NLuciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: NLuciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

While not associated, default the data rates to 1 and 2mbps, so that only
those rates will be used for association related message transfer. Once
associated, configure the full rate-set supported by the AP.
Signed-off-by: NJuuso Oikarinen <juuso.oikarinen@nokia.com>
Reviewed-by: NLuciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: NLuciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Remove the smart-reflex ACX - the associated parameters are now configured
in the radio parameters config.
Signed-off-by: NJuuso Oikarinen <juuso.oikarinen@nokia.com>
Reviewed-by: NLuciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: NLuciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Configure correct values to be used with the smart-reflex configuration of the
firmware.
Signed-off-by: NJuuso Oikarinen <juuso.oikarinen@nokia.com>
Reviewed-by: NLuciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: NLuciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

In the data path configuration, one of the parameters is the channel.  We
have been setting it to wl->channel, which is not correct in this case.  This
channel has nothing to do with the channel we're currently tuned to, since it
is only used for calibration during this phase.  Hardcoded the channel to 1,
according to the reference driver.
Signed-off-by: NLuciano Coelho <luciano.coelho@nokia.com>
Reviewed-by: NJuuso Oikarinen <juuso.oikarinen@nokia.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

In the new reference driver, some of the firmware configuration values have
been changed.  This patch changes them in the wl1271 driver accordingly.
Signed-off-by: NLuciano Coelho <luciano.coelho@nokia.com>
Reviewed-by: NJuuso Oikarinen <juuso.oikarinen@nokia.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

We were uploading the whole NVS file, but that is wrong, because the same
file also contains the initialization values.  For the latest firmwares, we
should upload only the initial 468 bytes from the file.
Signed-off-by: NLuciano Coelho <luciano.coelho@nokia.com>
Reviewed-by: NJuuso Oikarinen <juuso.oikarinen@nokia.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Some debugging tools require the chip to be powered on before they can work.
With these tools, we shouldn't upload the firmware nor boot the firmware
ourselves, so this debufs file is provided.  It always contains the gpio
power setting (0 = off, 1 = on).  To change the power setting, just write 0
or 1 to the file.
Signed-off-by: NLuciano Coelho <luciano.coelho@nokia.com>
Reviewed-by: NJuuso Oikarinen <juuso.oikarinen@nokia.com>
Reviewed-by: NKalle Valo <kalle.valo@nokia.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

There was a typo in one of the values in the rx_rssi_and_proc_compens elemt
of the Radio Parameters struct.
Signed-off-by: NLuciano Coelho <luciano.coelho@nokia.com>
Reviewed-by: NJuuso Oikarinen <juuso.oikarinen@nokia.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Newer firmwares require the dco itrim parameters to be set during
initialization.  This patch implements the new ACX function and calls it.
Signed-off-by: NLuciano Coelho <luciano.coelho@nokia.com>
Reviewed-by: NJuuso Oikarinen <juuso.oikarinen@nokia.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

We were using CONF_TX_RATE_MASK_ALL when calling wl1271_acx_rate_policies()
during init.  We should use WL1271_DEFAULT_BASIC_RATE_SET instead.  The
values are the same, but the latter is just the correct macro to use.
Signed-off-by: NLuciano Coelho <luciano.coelho@nokia.com>
Reviewed-by: NJuuso Oikarinen <juuso.oikarinen@nokia.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The call to wl1271_cmd_build_null_data() was missing when we got associated,
this was causing PS to fail.  This patch adds the call and now PS seems to
work.
Signed-off-by: NLuciano Coelho <luciano.coelho@nokia.com>
Reviewed-by: NJuuso Oikarinen <juuso.oikarinen@nokia.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

We were not checking the return value from the call to wl1271_cmd_join().
Added a check to make things more reliable.
Signed-off-by: NLuciano Coelho <luciano.coelho@nokia.com>
Reviewed-by: NJuuso Oikarinen <juuso.oikarinen@nokia.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The wl1271 firmware supports maximun 25.5dBm, so the driver was returning
-EINVALID to anything above that.  This patch uses the channel max_power
option to limit the TX power to 25dBm.
Signed-off-by: NLuciano Coelho <luciano.coelho@nokia.com>
Reviewed-by: NJuuso Oikarinen <juuso.oikarinen@nokia.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Now we're using a the idle information coming from mac80211 to decide when to
disconnect.  If we have joined (ie. we're listening to a channel), whenever
the interface goes to idle, we will issue a disconnect command.  So the
workaround to send a disconnect command before joining is not needed anymore.
Signed-off-by: NLuciano Coelho <luciano.coelho@nokia.com>
Reviewed-by: NJuuso Oikarinen <juuso.oikarinen@nokia.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

When we need to change the channel before association, we have to send a join
command with a valid BSSID.  With this patch we use 0baddeadbeef as the
BSSID.  There are ongoing discussions with TI to get this done in a cleaner
way.

When we go back to idle, we issue a CMD_DISCONNECT to make sure the firmware
stops listening to the channel and cleans things up internally.
Signed-off-by: NLuciano Coelho <luciano.coelho@nokia.com>
Reviewed-by: NJuuso Oikarinen <juuso.oikarinen@nokia.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Add new radio parameters for new structures based on firmware revision
6.1.0.0.288.
Signed-off-by: NLuciano Coelho <luciano.coelho@nokia.com>
Reviewed-by: NJuuso Oikarinen <juuso.oikarinen@nokia.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

There were some changes in the values we have to use for these settings.  This
patches updates them.
Signed-off-by: NLuciano Coelho <luciano.coelho@nokia.com>
Reviewed-by: NJuuso Oikarinen <juuso.oikarinen@nokia.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

In revision 6.1.0.0.288 the general parameters structure has changed.  This
patch updates the driver code accordingly.
Signed-off-by: NLuciano Coelho <luciano.coelho@nokia.com>
Reviewed-by: NJuuso Oikarinen <juuso.oikarinen@nokia.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

In revision 6.1.0.0.288 the radio parameters structure has changed.  This
patch updates the driver code accordingly.
Signed-off-by: NLuciano Coelho <luciano.coelho@nokia.com>
Reviewed-by: NJuuso Oikarinen <juuso.oikarinen@nokia.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Everything is ready now and we can enable WMM in mac80211.
Signed-off-by: NKalle Valo <kalle.valo@nokia.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Before transmission when aligning the buffer to 4-byte bounday, tx_hdr
needs to be updated. Otherwise debug logs print false data.
Signed-off-by: NKalle Valo <kalle.valo@nokia.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Now that necessary commands for WMM are implemented, implement queue handling
for WMM. But WMM is not enabled yet, only one queue is used.
Signed-off-by: NKalle Valo <kalle.valo@nokia.com>
Reviewed-by: NJanne Ylalehto <janne.ylalehto@nokia.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Needed for WMM.
Signed-off-by: NKalle Valo <kalle.valo@nokia.com>
Reviewed-by: NJanne Ylalehto <janne.ylalehto@nokia.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Needed for WMM.
Signed-off-by: NKalle Valo <kalle.valo@nokia.com>
Reviewed-by: NJanne Ylalehto <janne.ylalehto@nokia.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

RX is handled in a workqueue therefore allocating for GFP_ATOMIC
is overkill and not required.

Based on a patch for wl1271 by Luis R. Rodriguez.
Signed-off-by: NKalle Valo <kalle.valo@nokia.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The wakeup time calculation was too complicated, simplify it.
Signed-off-by: NKalle Valo <kalle.valo@nokia.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The original TI driver uses 100 ms timeout ELP wakeup timeout, better
to use the same. Otherwise problems with wakeup might get unnoticed.
Signed-off-by: NKalle Valo <kalle.valo@nokia.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Not all return values were checked and one exit from function didn't put
firmware sleep after the error.
Signed-off-by: NKalle Valo <kalle.valo@nokia.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This debug message was missing and caused incomplete log messages.
Signed-off-by: NKalle Valo <kalle.valo@nokia.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Sometimes when debugging the state is good info.
Signed-off-by: NKalle Valo <kalle.valo@nokia.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The bssid can be zero when null data template is set in wl1251_op_config().
It's enough, and especially safe, to set it once after association.
Signed-off-by: NKalle Valo <kalle.valo@nokia.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

bssid needs to be copied first in wl1251_op_bss_info_changed(), otherwise
templates will have incorrect bssid and power save will not work
correctly.
Signed-off-by: NKalle Valo <kalle.valo@nokia.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>