Among the many entries in the TSB12LV22 errata list (TI literature
number SLLS312) is the following:

  PCI Slave reads of the Cycle Timer register may occasionally get an
  incorrect value.
  Software may be able to validate value by reading the register
  multiple times rapidly and evaluating for a reasonable difference.

Signed-off-by: Clemens Ladisch <clemens@ladisch.de> (untested)
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de> (added #define)

If the bandwidth allocation fails, the error must be returned in
*channel regardless of whether the channel allocation succeeded.
Checking for c >= 0 is not correct if no channel allocation was
requested, in which case this part of the code is reached with
c == -EINVAL.
Signed-off-by: NClemens Ladisch <clemens@ladisch.de>
Signed-off-by: NStefan Richter <stefanr@s5r6.in-berlin.de>

by the number of available isochronous DMA contexts and active quirks
which is occasionally useful information.
Signed-off-by: NStefan Richter <stefanr@s5r6.in-berlin.de>

This bug was present in firewire-ohci since day one:  The number of
available isochronous receive DMA contexts was mixed up with that of
available isochronous transmit DMA contexts.

This is harmless on a few chips which offer the same number of contexts
in both directions, but most chips nowadays implement only the standard
minimum of 4 IR contexts, but 8 IT contexts.  If a user attempted to run
a lot of IR contexts at once, results with more than four were therefore
unpredictable.  I suppose the controller would simply refuse to start
DMA of any unimplemented context.
Signed-off-by: NStefan Richter <stefanr@s5r6.in-berlin.de>

This way, we can advise users of precompiled kernel packages to test
existing quirk fixes on chips which have not been listed yet, without
them having to build a kernel from source.

Note, to use this feature on a machine with more than one controller,
steps like these are necessary:
# lspci | grep 1394
# ls /sys/bus/pci/drivers/firewire_ohci/
# echo -n "0000:03:02.0" > /sys/bus/pci/drivers/firewire_ohci/unbind
# echo 2 > /sys/module/firewire_ohci/parameters/quirks
# echo -n "0000:03:02.0" > /sys/bus/pci/drivers/firewire_ohci/bind
# echo 0 > /sys/module/firewire_ohci/parameters/quirks

The parameter can also be used to switch off quirk flags that were
hardwired into firewire-ohci's quirks table.  Simply specify a non-zero
quirks value but without any known flags, e.g. 0x100.
Signed-off-by: NStefan Richter <stefanr@s5r6.in-berlin.de>

We don't have a lot of quirks to take into account (especially since
dual-buffer IR is out of the picture), but still, a table-based approach
is more organized than a series of if () clauses.
Signed-off-by: NStefan Richter <stefanr@s5r6.in-berlin.de>

The config_rom struct members are only accessed during relatively
infrequent self-ID-complete interrupts and only if the local config ROM
was changed, while the ar_, at_, ir_, it_ members are used very
frequently during I/O.  Hence move the config_rom members further down.

More importantly, make the huge self_id_buffer member the last one; this
is only accessed in self-ID-complete interrupts.
Signed-off-by: NStefan Richter <stefanr@s5r6.in-berlin.de>

This code was no longer used since 2.6.33, "firewire: ohci: always use
packet-per-buffer mode for isochronous reception" commit 090699c0.  If
anybody needs this code in the future for special purposes, it can be
brought back in.  But it must not be re-enabled by default; drivers
(kernelspace or userspace drivers) should only get this mode if they
explicitly request it.
Signed-off-by: NStefan Richter <stefanr@s5r6.in-berlin.de>

Signed-off-by: NStefan Richter <stefanr@s5r6.in-berlin.de>

from array of char to union of structs.  I already used a union to size
the buffer which holds ioctl arguments; more consequent is to define it
as an instance of this union in the first place.

Also rename several local variables from "request" to "a"(rgument) since
the term request can be mistaken to mean a transaction subaction, e.g.
an instance of struct fw_request.
Signed-off-by: NStefan Richter <stefanr@s5r6.in-berlin.de>

so that clients can detect whether the FW_CDEV_IOC_GET_CYCLE_TIMER ioctl
is reliable (on all tested controllers, especially the widely used VIA
controllers, also NEC controllers, see commits b677532b and 1c1517ef).

Also add a comment on the 2.6.32 iso xmit enhancement and on dual-buffer
IR having been disabled in 2.6.33.
Signed-off-by: NStefan Richter <stefanr@s5r6.in-berlin.de>

The system time from CLOCK_REALTIME is not monotonic, hence problematic
for the main user of the FW_CDEV_IOC_GET_CYCLE_TIMER ioctl.  This issue
exists in its successor ABI, i.e. raw1394, too.
http://subversion.ffado.org/ticket/242

We now offer an alternative ioctl which lets the caller choose between
CLOCK_REALTIME, CLOCK_MONOTONIC, and CLOCK_MONOTONIC_RAW as source of
the local time, very similar to the clock_gettime libc function.  The
format of the local time return value matches that of clock_gettime
(seconds and nanoseconds, instead of a single microseconds value from
the existing ioctl).
Signed-off-by: NStefan Richter <stefanr@s5r6.in-berlin.de>

according to what it really does.
Signed-off-by: NStefan Richter <stefanr@s5r6.in-berlin.de>

If a device exposes a sparsely populated configuration ROM,
firewire-core's sysfs interface and character device file interface
showed random data in the gaps between config ROM blocks.  Fix this by
zero-initialization of the config ROM reader's scratch buffer.
Signed-off-by: NStefan Richter <stefanr@s5r6.in-berlin.de>

The stack size of 16 was artificially chosen and may be too small in
extreme cases.  A device won't be accessible then.

Since it doesn't really matter to the slab allocator whether we ask for
1088 bytes or 2048 bytes of scratch memory, just allocate 2048 bytes for
the sum of temporary config ROM image and stack, and we will never ever
overflow the stack (because there simply can't be more stack items than
ROM entries).
Signed-off-by: NStefan Richter <stefanr@s5r6.in-berlin.de>

It never happened yet, but better safe than sorry:  If a device's config
ROM contains a block which overlaps the boundary at 0xfffff00007ff, just
ignore that one block instead of refusing to add the device
representation.  That way, upper layers (kernelspace or userspace
drivers) might still be able to use the device to some degree.

That's better than total inaccessibility of the device.  Worse, the core
would have logged only a generic "giving up on config rom" message which
could only be debugged by feeding a firewire-ohci debug logging session
through a config ROM interpreter, IOW would likely remain undiagnosed.
Signed-off-by: NStefan Richter <stefanr@s5r6.in-berlin.de>

The Panasonic AG-DV2500 tape deck contains an invalid entry in its
configuration ROM root directory:  A leaf pointer with the undefined key
ID 0 and an offset that points way out of the standard config ROM area.
This caused firewire-core to dismiss the device with the generic log
message "giving up on config rom for node id...", after which it was of
course impossible to access the tape deck with dvgrab or any other
program.  https://bugzilla.redhat.com/show_bug.cgi?id=449252#c29

The fix is to simply ignore this invalid ROM entry and proceed to read
the valid rest of the ROM.  There is a catch though:  When the kernel
later iterates over the ROM, it would be nasty having to check again for
such too large ROM offsets.  Therefore we manipulate the defective or
unsupported ROM entry to become a harmless immediate entry that won't
have any side effects later (an entry with the value 0x00000000).

Reported-by: George Chriss
Signed-off-by: NStefan Richter <stefanr@s5r6.in-berlin.de>

Signed-off-by: NStefan Richter <stefanr@s5r6.in-berlin.de>

* 'urgent' of git://git.kernel.org/pub/scm/linux/kernel/git/kyle/parisc-2.6:
  parisc: Set PCI CLS early in boot.

* 'release' of git://git.kernel.org/pub/scm/linux/kernel/git/aegl/linux-2.6:
  [IA64] Fix broken sn2 build

Set the PCI CLS early in the boot process to prevent
device failures. In pcibios_set_master use the new
pci_cache_line_size instead of a hard-coded value.
Signed-off-by: NCarlos O'Donell <carlos@codesourcery.com>
Reviewed-by: NGrant Grundler <grundler@google.com>
Signed-off-by: NKyle McMartin <kyle@redhat.com>

* 'for-linus' of git://git.monstr.eu/linux-2.6-microblaze:
  microblaze: Fix out_le32() macro
  microblaze: Fix cache loop function for cache range

* 'for-linus' of git://git.kernel.dk/linux-2.6-block:
  Revert "block: improve queue_should_plug() by looking at IO depths"

Trailing semicolon causes compilation involving out_le32() to fail.
Signed-off-by: NSteven J. Magnani <steve@digidescorp.com>
Signed-off-by: NMichal Simek <monstr@monstr.eu>

I create wrong asm code but none test shows that this part of code is wrong.
I am not convinces that were good idea to create asm optimized macros
for caches. The reason is that there is not optimization with previous code
that's why make sense to add old code and do some benchmarking which
functions are faster.
Signed-off-by: NMichal Simek <monstr@monstr.eu>

* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6:
  net: bug fix for vlan + gro issue
  tc35815: Remove a wrong netif_wake_queue() call which triggers BUG_ON
  cdc_ether: new PID for Ericsson C3607w to the whitelist (resubmit)
  IPv6: better document max_addresses parameter
  MAINTAINERS: update mv643xx_eth maintenance status
  e1000: Fix DMA mapping error handling on RX
  iwlwifi: sanity check before counting number of tfds can be free
  iwlwifi: error checking for number of tfds in queue
  iwlwifi: set HT flags after channel in rxon

Traffic (tcp) doesnot start on a vlan interface when gro is enabled.
Even the tcp handshake was not taking place.
This is because, the eth_type_trans call before the netif_receive_skb
in napi_gro_finish() resets the skb->dev to napi->dev from the previously
set vlan netdev interface. This causes the ip_route_input to drop the
incoming packet considering it as a packet coming from a martian source.

I could repro this on 2.6.32.7 (stable) and 2.6.33-rc7.
With this fix, the traffic starts and the test runs fine on both vlan
and non-vlan interfaces.

CC: Herbert Xu <herbert@gondor.apana.org.au>
CC: Patrick McHardy <kaber@trash.net>
Signed-off-by: NAjit Khaparde <ajitk@serverengines.com>
Signed-off-by: NHerbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

* 'release' of git://git.kernel.org/pub/scm/linux/kernel/git/lenb/linux-acpi-2.6:
  ACPI: Be in TS_POLLING state during mwait based C-state entry
  ACPI: Fix regression where _PPC is not read at boot even when ignore_ppc=0
  acer-wmi: Respect current backlight level when loading

* 'drm-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/airlied/drm-2.6:
  drm/vmwgfx: Fix queries if no dma buffer thrashing is occuring.
  drm/nv50: fix vram ptes on IGPs to point at stolen system memory
  drm/nv50: fix instmem binding on IGPs to point at stolen system memory
  drm/nv50: improve vram page table construction
  drm/nv50: more efficient clearing of gpu page table entries
  drm/nv50: make nv50_mem_vm_{bind,unbind} operate only on vram
  drm/nouveau: Fix up pre-nv17 analog load detection.

Revert the change made to arch/ia64/sn/kernel/setup.c by commit
204fba4a as it breaks the build.

Fixing the build the b94b0808 way
breaks xpc because genksyms then fails to generate an CRC for
per_cpu____sn_cnodeid_to_nasid because of limitations in the
generic genksyms code.
Signed-off-by: NHedi Berriche <hedi@sgi.com>
Signed-off-by: NTony Luck <tony.luck@intel.com>

The netif_wake_queue() is called correctly (i.e. only on !txfull
condition) from txdone routine.  So Unconditional call to the
netif_wake_queue() here is wrong.  This might cause calling of
start_xmit routine on txfull state and trigger BUG_ON.

This bug does not happen when NAPI disabled.  After txdone there
must be at least one free tx slot.  But with NAPI, this is not
true anymore and the BUG_ON can hits on heavy load.

In this driver NAPI was enabled on 2.6.33-rc1 so this is
regression from 2.6.32 kernel.
Reported-by: NRalf Roesch <ralf.roesch@rw-gmbh.de>
Signed-off-by: NAtsushi Nemoto <anemo@mba.ocn.ne.jp>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch adds a new vid/pid to the cdc_ether whitelist.

Device added:
- Ericsson Mobile Broadband variant C3607w
Signed-off-by: NTorgny Johansson <torgny.johansson@gmail.com>

--
To unsubscribe from this list: send the line "unsubscribe netdev" in
the body of a message to majordomo@vger.kernel.org
More majordomo info at  http://vger.kernel.org/majordomo-info.htmlSigned-off-by: NDavid S. Miller <davem@davemloft.net>

Andrew Morton wrote:
>> >From ip-sysctl.txt file in kernel documentation I can see following description
>> for max_addresses:
>> max_addresses - INTEGER
>>         Number of maximum addresses per interface.  0 disables limitation.
>>         It is recommended not set too large value (or 0) because it would
>>         be too easy way to crash kernel to allow to create too much of
>>         autoconfigured addresses.
           ^^^^^^^^^^^^^^

>> If this parameter applies only for auto-configured IP addressed, please state
>> it more clearly in docs or rename the parameter to show that it refers to
>> auto-configuration.

It did mention autoconfigured in the text, but the below makes it more obvious.

More clearly document IPv6 max_addresses parameter.
Signed-off-by: NBrian Haley <brian.haley@hp.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

I am no longer with Marvell.
Signed-off-by: NLennert Buytenhek <buytenh@wantstofly.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Check for error return from pci_map_single/pci_map_page and clean up.

With this and the previous patch the driver was able to handle a significant
percentage of errors (I set the fault injection rate to 10% and could still
download large files at a reasonable speed).
Signed-off-by: NAnton Blanchard <anton@samba.org>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This reverts commit fb1e7538.

"Benjamin S." <sbenni@gmx.de> reports that the patch in question
causes a big drop in sequential throughput for him, dropping from
200MB/sec down to only 70MB/sec.

Needs to be investigated more fully, for now lets just revert the
offending commit.

Conflicts:

	include/linux/blkdev.h
Signed-off-by: NJens Axboe <jens.axboe@oracle.com>

Intercept query commands and apply relocations to their guest pointers.
Signed-off-by: NThomas Hellstrom <thellstrom@vmware.com>
Signed-off-by: NDave Airlie <airlied@redhat.com>

* 'nouveau/for-airlied' of ../drm-nouveau-next:
  drm/nv50: fix vram ptes on IGPs to point at stolen system memory
  drm/nv50: fix instmem binding on IGPs to point at stolen system memory
  drm/nv50: improve vram page table construction
  drm/nv50: more efficient clearing of gpu page table entries
  drm/nv50: make nv50_mem_vm_{bind,unbind} operate only on vram
  drm/nouveau: Fix up pre-nv17 analog load detection.