The hard-wired configuration of the top speed (until now S800) was
unnecessary, remove it.

If the local link layer controller supports S1600 or S3200, we now
assume this speed for all present 1394b PHYs (except if they are
behind 1394a repeaters) until nodemgr figured out the actual speed
while fetching the config ROM.
Signed-off-by: NStefan Richter <stefanr@s5r6.in-berlin.de>

This fixes a regression by "firewire: keep highlevel drivers attached
during brief connection loss":  There were 2 seconds unnecessary waiting
added to the shutdown procedure of each controller.

We use card->link as status flag to signal the device handler that there
is no use to wait for a come-back.
Signed-off-by: NStefan Richter <stefanr@s5r6.in-berlin.de>

Camcorders have a tendency to fail read requests to their config ROM and
write request to their FCP command register with ack_busy_X.  This has
become a problem with newer kernels and especially Panasonic camcorders,
causing AV/C in dvgrab and kino to fail.  Dvgrab for example frequently
logs "send oops"; kino reports loss of AV/C control.  I suspect that
lower CPU scheduling latencies in newer kernels made this issue more
prominent now.

According to
https://sourceforge.net/tracker/?func=detail&atid=114103&aid=2492640&group_id=14103
this can be fixed by configuring the FireWire controller for more
hardware retries for request transmission; these retries are evidently
more successful than libavc1394's own retry loop (typically 3 tries on
top of hardware retries).

Presumably the same issue has been reported at
https://bugzilla.redhat.com/show_bug.cgi?id=449252 and
https://bugzilla.redhat.com/show_bug.cgi?id=477279 .

Tested-by: Mathias Beilstein
Signed-off-by: NStefan Richter <stefanr@s5r6.in-berlin.de>

Camcorders have a tendency to fail read requests to their config ROM and
write request to their FCP command register with ack_busy_X.  This has
become a problem with newer kernels and especially Panasonic camcorders,
causing AV/C in dvgrab and kino to fail.  Dvgrab for example frequently
logs "send oops"; kino reports loss of AV/C control.  I suspect that
lower CPU scheduling latencies in newer kernels made this issue more
prominent now.

According to
https://sourceforge.net/tracker/?func=detail&atid=114103&aid=2492640&group_id=14103
this can be fixed by configuring the FireWire controller for more
hardware retries for request transmission; these retries are evidently
more successful than libavc1394's own retry loop (typically 3 tries on
top of hardware retries).

Presumably the same issue has been reported at
https://bugzilla.redhat.com/show_bug.cgi?id=449252 and
https://bugzilla.redhat.com/show_bug.cgi?id=477279 .

In a quick test with a JVC camcorder (which didn't malfunction like the
reported camcorders), this change decreased the number of ack_busy_X
from 16 in three runs of dvgrab to 4 in three runs of the same capture
duration.
Signed-off-by: NStefan Richter <stefanr@s5r6.in-berlin.de>

The present message is mostly just noise.  We only need to be notified
if the "active" flag does not go off before the retry loop terminates.
Signed-off-by: NStefan Richter <stefanr@s5r6.in-berlin.de>

There are situations when nodes vanish from the bus and come back
quickly thereafter:
  - When certain bus-powered hubs are plugged in,
  - when certain devices are plugged into 6-port hubs,
  - when certain disk enclosures are switched from self-power to bus
    power or vice versa and break the daisy chain during the transition,
  - when the user plugs a cable out and quickly plugs it back in, e.g.
    to reorder a daisy chain (works on Mac OS X if done quickly enough),
  - when certain hubs temporarily malfunction during high bus traffic.

Until now, firewire-core reported affected nodes as lost to the
highlevel drivers (firewire-sbp2 and userspace drivers).  We now delay
the destruction of device representations until after at least two
seconds after the last bus reset.  If a "new" device is detected in this
period whose bus information block and root directory header match that
of a device which is pending for deletion, we resurrect that device and
send update calls to highlevel drivers.
Signed-off-by: NStefan Richter <stefanr@s5r6.in-berlin.de>

Noticed by Jarod Wilson:  The bus manager work was unnecessarily delayed
each time the bus generation counter rolled over.
Signed-off-by: NStefan Richter <stefanr@s5r6.in-berlin.de>
Signed-off-by: NJarod Wilson <jwilson@redhat.com>

The whole topology code only works if the old and new topologies which
are compared come from immediately successive self ID complete events.

If there happened bus resets without self ID complete events in the
meantime, or self ID complete events with invalid selfIDs, the topology
comparison could identify nodes wrongly, or more likely just corrupt
kernel memory or panic right away.

We now discard all nodes of the old topology and treat all current nodes
as new ones if the current self ID generation is not the previous one
plus 1.
Signed-off-by: NStefan Richter <stefanr@s5r6.in-berlin.de>
Signed-off-by: NJarod Wilson <jwilson@redhat.com>

ACPI hotplug panic with current git head
http://lkml.org/lkml/2009/1/10/136

Rather than reverting the entire commit that causes the crash:
e8c331e9
"PCI hotplug: introduce functions for ACPI slot detection"

simply harden against it while the changes to
the hotplug code on this particularl machine are understood.
Signed-off-by: NJames Bottomley <James.Bottomley@HansenPartnership.com>
Acked-by: NJesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: NLen Brown <len.brown@intel.com>

Signed-off-by: NLen Brown <len.brown@intel.com>

Signed-off-by: NLen Brown <len.brown@intel.com>

Although rfkill support for the EEE bluetooth device has been added to
2.6.28-rc the appropriate ACPI accessor definitions were not added, so
the support was non functional. The patch below adds the get and set
accessors and has been verified to work on an EEE 901.
Signed-off-by: NJonathan McDowell <noodles@earth.li>
Acked-by: NMatthew Garrett <mjg@redhat.com>
Acked-by: NCorentin Chary <corentincj@iksaif.net>
Signed-off-by: NLen Brown <len.brown@intel.com>

ACPI thermal driver only re-evaluate VALID trip points.

For the broken BIOS show in
http://bugzilla.kernel.org/show_bug.cgi?id=8544
the active[0] is set to invalid at boot time
and it will not be re-evaluated again.
We can still get a single warning message at boot time.

http://marc.info/?l=linux-kernel&m=120496222629983&w=2

http://bugzilla.kernel.org/show_bug.cgi?id=12203

Signed-off-by: Zhang Rui<rui.zhang@intel.com>
Tested-by: NMárton Németh <nm127@freemail.hu>
Signed-off-by: NLen Brown <len.brown@intel.com>

Fixes a build error in absence of CONFIG_IPV6:

drivers/net/netxen/netxen_nic_main.c:1189: error: implicit declaration of function 'ipv6_hdr'
drivers/net/netxen/netxen_nic_main.c:1189: error: invalid type argument of '->'
Reported-by: NIngo Molnar <mingo@elte.hu>
Signed-off-by: NDhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

http://bugzilla.kernel.org/show_bug.cgi?id=9399
http://bugzilla.kernel.org/show_bug.cgi?id=11880Signed-off-by: NAlexey Starikovskiy <astarikovskiy@suse.de>
Signed-off-by: NLen Brown <len.brown@intel.com>

For NX3031 only one I/O range is mapped, so unmapping other
two which are used by older chips, causes this warning on
ppc64.

"Attempt to iounmap early bolted mapping at 0x0000000000000000"
Signed-off-by: NDhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

References: http://bugzilla.kernel.org/show_bug.cgi?id=11884Signed-off-by: NAlexey Starikovskiy <astarikovskiy@suse.de>
Signed-off-by: NLen Brown <len.brown@intel.com>

This reverts commit 98e6e286, as Yinghai
Lu reports that it breaks kexec with at least the e1000 and e1000e
drivers.  The reason is that the shutdown sequence puts the hardware
into D3 sleep, and the commit causes us to claim that it then is in D0
(running) state just because we don't understand the PM capabilities.

Which then later makes "pci_set_power_state()" not do anything, and the
device never wakes up properly and just returns 0xff to everything.
Reported-by: NYinghai Lu <yinghai@kernel.org>
Acked-by: NFrom: Rafael J. Wysocki <rjw@sisk.pl>
Cc: Jesse Barnes <jesse.barnes@intel.com>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

while I was looking over kernel sources I've found this small bug.

Formerly, zero was returned even if an error happened.
Signed-off-by: NMichal Sojka <sojkam1@fel.cvut.cz>
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

drivers/ata/pata_ali.c:44: error: static declaration of 'isa_bridge' follows non-static declaration
arch/alpha/include/asm/pci.h:274: error: previous declaration of 'isa_bridge' was here

Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Cc: Jeff Garzik <jeff@garzik.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

Cavium OCTEON processor support was recently merged, so now we have
this CF driver for your consideration.

Most OCTEON variants have *no* DMA or interrupt support on the CF
interface so for these, only PIO is supported.  Although if DMA is
available, we do take advantage of it.
Signed-off-by: NDavid Daney <ddaney@caviumnetworks.com>
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

The forthcoming OCTEON SOC Compact Flash driver needs an additional
timing value that was not available in the ata_timing table.  I add a
new column for dmack_hold time.  The values were obtained from the
Compact Flash specification Rev 4.1.
Signed-off-by: NDavid Daney <ddaney@caviumnetworks.com>
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

Signed-off-by: NJoseph Chan <josephchan@via.com.tw>
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

Port enabledness test fits much better into init_one() instead of
pre_reset().  The reason why these tests are in pre_reset() is purely
historical at this point.  Move it to init_one().  This will help
further changes.
Signed-off-by: NTejun Heo <tj@kernel.org>
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

for SAS drivers.

Caught by Ke Wei (and team?) at Marvell.

Also, move the ata_scsi_ioctl export to libata-scsi.c, as that seems to be the
general trend.
Acked-by: NJames Bottomley <James.Bottomley@HansenPartnership.com>
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

This makes sure the mutex is held around the unreference.
Signed-off-by: NDave Airlie <airlied@redhat.com>

This is an initial patch to do support for objects which needs physical
contiguous main ram, cursors and overlay registers on older chipsets.

These objects are bound on cursor bin, like pinning, and we copy
the data to/from the backing store object into the real one on attach/detach.

notes:
possible over the top in attach/detach operations.
no overlay support yet.
Signed-off-by: NDave Airlie <airlied@redhat.com>

The detected fixed panel mode really is preferred, so mark it as such and
add it to the LVDS connector mode list.
Signed-off-by: NJesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: NEric Anholt <eric@anholt.net>
Signed-off-by: NDave Airlie <airlied@linux.ie>

Signed-off-by: NJesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: NEric Anholt <eric@anholt.net>
Signed-off-by: NDave Airlie <airlied@linux.ie>

When mode setting is first initialized, the driver will call into
drm_helper_initial_config() to set up an initial output and framebuffer
configuration.  This routine is responsible for probing the available
connectors, encoders, and crtcs, looking for modes and putting together
something reasonable (where reasonable is defined as "allows kernel
messages to be visible on as many displays as possible").

However, the code was a bit too aggressive in setting default modes when
none were found on a given connector.  Even if some connectors had modes,
any connectors found lacking modes would have the default 800x600 mode added
to their mode list, which in some cases could cause problems later down the
line.  In my case, the LVDS was perfectly available, but the initial config
code added 800x600 modes to both of the detected but unavailable HDMI
connectors (which are on my non-existent docking station).  This ended up
preventing later code from setting a mode on my LVDS, which is bad.

This patch fixes that behavior by making the initial config code walk
through the connectors first, counting the available modes, before it decides
to add any default modes to a possibly connected output.  It also fixes the
logic in drm_target_preferred() that was causing zeroed out modes to be set
as the preferred mode for a given connector, even if no modes were available.
Signed-off-by: NJesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: NEric Anholt <eric@anholt.net>
Signed-off-by: NDave Airlie <airlied@linux.ie>

This patch adds support for "ns16850" as supported value
of the compatible node in flat device tree uart descriptions.

This is needed for example when you have a XR16C2850 uart
connected to a PPC405's external bus controller.
Signed-off-by: NMatthias Fuchs <mfuchs@ma-fu.de>
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>

This patch removes the tty->low_latency setting.

For irq based hvc_console backends the tty->low_latency must be set to 0,
because the tty_flip_buffer_push() function must not be called from IRQ context
(see drivers/char/tty_buffer.c).

For polled backends, the low_latency setting causes the bug trace below, because
tty_flip_buffer_push() is called within an atomic context and subsequent calls
might sleep due to mutex_lock.

BUG: sleeping function called from invalid context at /root/cvs/linux-2.6.git/kernel/mutex.c:207
in_atomic(): 1, irqs_disabled(): 0, pid: 748, name: khvcd
1 lock held by khvcd/748:
 #0:  (hvc_structs_lock){--..}, at: [<00000000002ceb50>] khvcd+0x58/0x12c
CPU: 0 Not tainted 2.6.29-rc1git #29
Process khvcd (pid: 748, task: 000000002fb9a480, ksp: 000000002f66bd78)
070000000000000a 000000002f66ba00 0000000000000002 (null)
       000000002f66baa0 000000002f66ba18 000000002f66ba18 0000000000104f08
       ffffffffffffc000 000000002f66bd78 (null) (null)
       000000002f66ba00 000000000000000c 000000002f66ba00 000000002f66ba70
       0000000000466af8 0000000000104f08 000000002f66ba00 000000002f66ba50
Call Trace:
([<0000000000104e7c>] show_trace+0x138/0x158)
 [<0000000000104f62>] show_stack+0xc6/0xf8
 [<0000000000105740>] dump_stack+0xb0/0xc0
 [<000000000013144a>] __might_sleep+0x14e/0x17c
 [<000000000045e226>] mutex_lock_nested+0x42/0x3b4
 [<00000000002c443e>] echo_char_raw+0x3a/0x9c
 [<00000000002c688c>] n_tty_receive_buf+0x1154/0x1208
 [<00000000002ca0a2>] flush_to_ldisc+0x152/0x220
 [<00000000002ca1da>] tty_flip_buffer_push+0x6a/0x90
 [<00000000002cea74>] hvc_poll+0x244/0x2c8
 [<00000000002ceb68>] khvcd+0x70/0x12c
 [<000000000015bbd0>] kthread+0x68/0xa0
 [<0000000000109d5a>] kernel_thread_starter+0x6/0xc
 [<0000000000109d54>] kernel_thread_starter+0x0/0xc
1 lock held by khvcd/748:
 #0:  (hvc_structs_lock){--..}, at: [<00000000002ceb50>] khvcd+0x58/0x12c
Signed-off-by: NHendrik Brueckner <brueckner@linux.vnet.ibm.com>
Acked-by: NChristian Borntraeger <borntraeger@de.ibm.com>
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>

Signed-off-by: NStephen Rothwell <sfr@canb.auug.org.au>
Acked-by: NGeoff Levand <geoffrey.levand@am.sony.com>
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>

Signed-off-by: NStephen Rothwell <sfr@canb.auug.org.au>
Acked-by: NGeoff Levand <geoffrey.levand@am.sony.com>
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>

Also some min -> mint_t conversion.
Signed-off-by: NStephen Rothwell <sfr@canb.auug.org.au>
Acked-by: NGeoff Levand <geoffrey.levand@am.sony.com>
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>

Also a couple of min -> min_t changes.
Signed-off-by: NStephen Rothwell <sfr@canb.auug.org.au>
Acked-by: NGeoff Levand <geoffrey.levand@am.sony.com>
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>

Signed-off-by: NStephen Rothwell <sfr@canb.auug.org.au>
Acked-by: NGeoff Levand <geoffrey.levand@am.sony.com>
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>

We just fix up the reference parameters as the others are dealt with by
arithmetic promotion rules and don't cause warnings.

This removes warnings like this:

arch/powerpc/platforms/ps3/interrupt.c:327: warning: passing argument 1 of 'lv1_construct_event_receive_port' from incompatible pointer type

Also, these:

drivers/ps3/ps3-vuart.c:462: warning: passing argument 4 of 'ps3_vuart_raw_read' from incompatible pointer type
drivers/ps3/ps3-vuart.c:592: warning: passing argument 4 of 'ps3_vuart_raw_read' from incompatible pointer type
Signed-off-by: NStephen Rothwell <sfr@canb.auug.org.au>
Acked-by: NGeoff Levand <geoffrey.levand@am.sony.com>
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>

This is a powerpc specific driver.
Signed-off-by: NStephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>

Carry out the PM-routine interface change in the USB OTG pathway.  This
was omitted from the earlier interface-change patch by mistake.
Signed-off-by: NAlan Stern <stern@rowland.harvard.edu>
Cc: Greg KH <greg@kroah.com>
Cc: Russell King <rmk@arm.linux.org.uk>
Cc: Felipe Balbi <felipe.balbi@nokia.com>
Cc: Tony Lindgren <tony@atomide.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>