Fix AER settings for BCM57712 to allow accessing all device addresses range in CL45 MDC/MDIO
Signed-off-by: NYaniv Rosner <yanivr@broadcom.com>
Signed-off-by: NEilon Greenstein <eilong@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Fix BCM84823 LED behavior which may show on some systems
Signed-off-by: NYaniv Rosner <yanivr@broadcom.com>
Signed-off-by: NEilon Greenstein <eilong@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Device may show incorrect duplex mode for devices with external PHY
Signed-off-by: NYaniv Rosner <yanivr@broadcom.com>
Signed-off-by: NEilon Greenstein <eilong@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Improve microcode loading verification before proceeding to next stage
Signed-off-by: NYaniv Rosner <yanivr@broadcom.com>
Signed-off-by: NEilon Greenstein <eilong@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

LED on BCM57712+BCM8727 systems requires different settings
Signed-off-by: NYaniv Rosner <yanivr@broadcom.com>
Signed-off-by: NEilon Greenstein <eilong@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Common init used to be called by the driver when the first port comes up, mainly to reset and reload external PHY microcode.
However, in case management driver is active on the other port, traffic would halted. So limit the common init to be done only once after POR.
Signed-off-by: NYaniv Rosner <yanivr@broadcom.com>
Signed-off-by: NEilon Greenstein <eilong@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Enable controlling BCM8073 PN polarity swap through nvm configuration, which is required in certain systems
Signed-off-by: NYaniv Rosner <yanivr@broadcom.com>
Signed-off-by: NEilon Greenstein <eilong@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

We dereferenced params on the line before so it's too late to check if
params is NULL.  In fact, params can never be NULL and strict_cos is
either 0 or 1 so that part of the check is bogus too.  Let's remove it.
Signed-off-by: NDan Carpenter <error27@gmail.com>
Acked-by: NEilon Greenstein <eilong@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add appropriate HW DCB/PFC configuration
Signed-off-by: NDmitry Kravkov <dmitry@broadcom.com>
Signed-off-by: NEilon Greenstein <eilong@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NJoe Perches <joe@perches.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Resetting 8073 during common init is required on boards in which the
8073 reset pin is not asserted by default.
Signed-off-by: NYaniv Rosner <yanivr@broadcom.com>
Signed-off-by: NEilon Greenstein <eilong@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Enabling CL37 BAM on BCM8073 by default may lead to link issues since
not all switches support it. So enable CL37 BAM only if explicitly
selected.
Signed-off-by: NYaniv Rosner <yanivr@broadcom.com>
Signed-off-by: NEilon Greenstein <eilong@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

On BCM8726 based designs, the ports are swapped, hence the reset needs
to be asserted through port0 and not port1.
Signed-off-by: NYaniv Rosner <yanivr@broadcom.com>
Signed-off-by: NEilon Greenstein <eilong@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When using latch indication for link change notification, need to
clear it when port is unloaded, otherwise it might generate false
indication on next load.
Signed-off-by: NYaniv Rosner <yanivr@broadcom.com>
Signed-off-by: NEilon Greenstein <eilong@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

On E2 flavor, dual-port mode, the port argument used for some
functions is needed as the global port number rather than the port per
path.
Signed-off-by: NYaniv Rosner <yanivr@broadcom.com>
Signed-off-by: NEilon Greenstein <eilong@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

BCM848x3 requires additional of 50ms after reset done indication,
instead of fixed time of 200ms
Signed-off-by: NYaniv Rosner <yanivr@broadcom.com>
Signed-off-by: NEilon Greenstein <eilong@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Fix delay during BMAC reset from 10usec to 1ms.
Signed-off-by: NYaniv Rosner <yanivr@broadcom.com>
Signed-off-by: NEilon Greenstein <eilong@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Make many functions that are only used in one file static.
Remove dead code for override_led_value.
Signed-off-by: NStephen Hemminger <shemminger@vyatta.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

57712 HW supported with same set of features as for 57710/57711
Signed-off-by: NDmitry Kravkov <dmitry@broadcom.com>
Signed-off-by: NEilon Greenstein <eilong@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This is the new FW HSI blob and the relevant definitions without logic changes.
It also included code adaptation for new HSI. New features are not enabled.

New FW/HSI includes:
- Support for 57712 HW
- Future support for VF (not used)
- Improvements in FW interrupts scheme
- FW FCoE hooks (stubs for future usage)
Signed-off-by: NDmitry Kravkov <dmitry@broadcom.com>
Signed-off-by: NMichael Chan <mchan@broadcom.com>
Signed-off-by: NEilon Greenstein <eilong@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This is a partial revert of 0b1974de ("Fix typo: configuation
=> configuration") as this hunk is removed in net-next.
Reported-by: NStephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: NJiri Kosina <jkosina@suse.cz>

Signed-off-by: NThomas Weber <weber@corscience.de>
Acked-by: NDavid S. Miller <davem@davemloft.net>
Signed-off-by: NJiri Kosina <jkosina@suse.cz>

Change LED scheme for dual-media
Signed-off-by: NYaniv Rosner <yanivr@broadcom.com>
Signed-off-by: NEilon Greenstein <eilong@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add required changes in order to support dual-media boards.
Signed-off-by: NYaniv Rosner <yanivr@broadcom.com>
Signed-off-by: NEilon Greenstein <eilong@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Group all PHY specific functions together to have an organized code
Signed-off-by: NYaniv Rosner <yanivr@broadcom.com>
Signed-off-by: NEilon Greenstein <eilong@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Make the needed changes for the new scheme especially around PHY
initialization, and link detection.
- The get_emac_base function was changed to enable setting different MAC
access setting for each PHY based of external configuration.
- As a part of the dual-media preparation, the save_spirom_version was
modified to accept a PHY specific version address to be saved in the
shmem. This will enable to save more than single spirom version in

different locations.
- The test_link function was changed also as a preparation for the
dual-media upcoming changes
- Duplicate initialization logic was removed from the
link_setting_status and link_initialize functions
Signed-off-by: NYaniv Rosner <yanivr@broadcom.com>
Signed-off-by: NEilon Greenstein <eilong@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Move all PHY specific logic from bnx2x_main into bnx2x_link.
Signed-off-by: NYaniv Rosner <yanivr@broadcom.com>
Signed-off-by: NEilon Greenstein <eilong@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Flow control implementation is split to be done in each PHY function.
Signed-off-by: NYaniv Rosner <yanivr@broadcom.com>
Signed-off-by: NEilon Greenstein <eilong@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

In previous patch, common PHY functions were split in simple way to
allow easy diff. This patch comes to align code in the new functions.
In addition, the non-production BCM8072 PHY was removed.
Signed-off-by: NYaniv Rosner <yanivr@broadcom.com>
Signed-off-by: NEilon Greenstein <eilong@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Move the code into PHY oriented functions, and for that a new structure
is defines for each PHY which contain PHY properties and its own
functions. This also enables to encapsulate all PHY specific operations
into the PHY functions. During initialization, the PHYs will be probed
by the "bnx2x_phy_probe" function to detect which PHYs exist on-board,
and configure them accordingly. Note that the ext_phy_reset
implementation was incorporated in the ext_phy_init since it is actually
part of the PHY initialization procedure.
Signed-off-by: NYaniv Rosner <yanivr@broadcom.com>
Signed-off-by: NEilon Greenstein <eilong@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Start building the infrastructure for dual media by adding new component
of PHY which will be used all along the function. Modify function to
work with this component instead of the link_params.
Signed-off-by: NYaniv Rosner <yanivr@broadcom.com>
Signed-off-by: NEilon Greenstein <eilong@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Change 848xx LED configuration according to the new microcode (Boards
were shipped with only with the new microcode)
Signed-off-by: NYaniv Rosner <yanivr@broadcom.com>
Signed-off-by: NEilon Greenstein <eilong@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Remove unneeded setting of XAUI low power to BCM8727. This was required
only in older microcode which is not in the field.
Signed-off-by: NYaniv Rosner <yanivr@broadcom.com>
Signed-off-by: NEilon Greenstein <eilong@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Change BCM848xx behavior to fit IEEE such that setting 10Mb/100Mb will
use force speed, and setting 1Gb/10Gb will use auto-negotiation with the
specific speed advertised
Signed-off-by: NYaniv Rosner <yanivr@broadcom.com>
Signed-off-by: NEilon Greenstein <eilong@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

In BCM8727 based boards, setting default 10G link speed after link was
set to 1G may lead to link down issue. The problem was setting the right
value, but to the wrong registers
Signed-off-by: NYaniv Rosner <yanivr@broadcom.com>
Signed-off-by: NEilon Greenstein <eilong@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Fix potential link issue caused by insufficient delay time during SPIROM
load of BCM8073/BCM8727
Signed-off-by: NYaniv Rosner <yanivr@broadcom.com>
Signed-off-by: NEilon Greenstein <eilong@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Outdent the code following the if.

The semantic match that finds this problem is as follows:
(http://coccinelle.lip6.fr/)

// <smpl>
@r disable braces4@
position p1,p2;
statement S1,S2;
@@

(
if (...) { ... }
|
if (...) S1@p1 S2@p2
)

@script:python@
p1 << r.p1;
p2 << r.p2;
@@

if (p1[0].column == p2[0].column):
  cocci.print_main("branch",p1)
  cocci.print_secs("after",p2)
// </smpl>
Signed-off-by: NJulia Lawall <julia@diku.dk>
Acked-by: NEilon Greenstein <eilong@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This commit includes files movement to newly created folder
using git-mv command and fixes references in cnic and bnx2x code
to each other.

files moved using following:
#!/bin/bash
mkdir drivers/net/bnx2x/
list=$(cd drivers/net/ && ls bnx2x*.[ch])
for f in $list; do
        git mv -f drivers/net/$f drivers/net/bnx2x/$f
done
Signed-off-by: NDmitry Kravkov <dmitry@broadcom.com>
Signed-off-by: NEilon Greenstein <eilong@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Change 2wire transfer rate of SFP+ module EEPROM from 400Khz to 100Khz
since some DACs(direct attached cables) do not work at 400Khz.
Reported-by: NKrzysztof Oldzki <ole@ans.pl>
Signed-off-by: NYaniv Rosner <yanivr@broadcom.com>
Signed-off-by: NEilon Greenstein <eilong@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NFrans Pop <elendil@planet.nl>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>