Signed-off-by: NYaniv Rosner <yanivr@broadcom.com>
Signed-off-by: NEilon Greenstein <eilong@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch fixes a link problem on BCM57712 + BCM8727 designs in which the TX
laser is controller by GPIO, after 1.60.xx drivers were previously loaded.
On these designs the TX_LASER is enabled by logic AND between the PHY
(through MDIO), and the GPIO. When an old driver is used, it disables the
MDIO part, hence the GPIO control had no affect de facto.
Signed-off-by: NYaniv Rosner <yanivr@broadcom.com>
Signed-off-by: NEilon Greenstein <eilong@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Fix no-LED problem when link speed is 1G on BCM57712 + BCM8727 designs, by
removing a logic error checking for a different PHY.
Signed-off-by: NYaniv Rosner <yanivr@broadcom.com>
Signed-off-by: NEilon Greenstein <eilong@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Fix 578x0-SFI pre-emphasis settings per HW recommendations to achieve better
link strength.
Signed-off-by: NYaniv Rosner <yanivr@broadcom.com>
Signed-off-by: NEilon Greenstein <eilong@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

BCM57810-KR link may not come up in 1G after running loopback test, so set
the relevant registers to their default values before starting KR autoneg.
Signed-off-by: NYaniv Rosner <yanivr@broadcom.com>
Signed-off-by: NEilon Greenstein <eilong@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Fix 57810-KR flow-control handling link is achieved via CL37 AN.
Signed-off-by: NYaniv Rosner <yanivr@broadcom.com>
Signed-off-by: NEilon Greenstein <eilong@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Fix a problem in which PFC frames are not honored, due to incorrect link
attributes synchronization following PMF migration, and verify PFC XON is not
stuck from previous link change.
Signed-off-by: NYaniv Rosner <yanivr@broadcom.com>
Signed-off-by: NEilon Greenstein <eilong@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Modified from original patch from Chris.

The sky2 driver has to have 8 byte alignment of receive buffer
on some chip versions. On architectures which don't support efficient
unaligned access this doesn't work very well. The solution is to
just copy all received packets which is what the driver already
does for small packets.

This allows the driver to be used on the Tilera TILEmpower-Gx, since
the tile architecture doesn't currently handle kernel unaligned accesses,
just userspace.
Signed-off-by: NStephen Hemminger <shemminger@vyatta.com>
Acked-by: NChris Metcalf <cmetcalf@tilera.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The current implemenation was buggy for slaves who use ndo_neigh_setup,
since the networking stack invokes the bonding device ndo entry (from
neigh_params_alloc) before any devices are enslaved, and the bonding
driver can't further delegate the call at that point in time. As a
result when bonding IPoIB devices, the neigh_cleanup hasn't been called.

Fix that by deferring the actual call into the slave ndo_neigh_setup
from the time the bonding neigh_setup is called.
Signed-off-by: NShlomo Pongratz <shlomop@mellanox.com>
Signed-off-by: NJay Vosburgh <fubar@us.ibm.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

commit 7d26bb10 "bonding: emit event when bonding changes MAC" didn't
take care to emit the NETDEV_CHANGEADDR event in bond_release, where bonding
actually changes the mac address (to all zeroes). As a result the neighbours
aren't deleted by the core networking code (which does so upon getting that
event).
Signed-off-by: NShlomo Pongratz <shlomop@mellanox.com>
Signed-off-by: NJay Vosburgh <fubar@us.ibm.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

getsockopt(..., SCTP_EVENTS, ...) performs a length check and returns
an error if the user provides less bytes than the size of struct
sctp_event_subscribe.

Struct sctp_event_subscribe needs to be extended by an u8 for every
new event or notification type that is added.

This obviously makes getsockopt fail for binaries that are compiled
against an older versions of <net/sctp/user.h> which do not contain
all event types.

This patch changes getsockopt behaviour to no longer return an error
if not enough bytes are being provided by the user. Instead, it
returns as much of sctp_event_subscribe as fits into the provided buffer.

This leads to the new behavior that users see what they have been aware
of at compile time.

The setsockopt(..., SCTP_EVENTS, ...) API is already behaving like this.
Signed-off-by: NThomas Graf <tgraf@suug.ch>
Acked-by: NVlad Yasevich <vladislav.yasevich@hp.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

We have to decrement the conntrack counter if we fail to access the
zone extension.
Reported-by: NTetsuo Handa <penguin-kernel@I-love.SAKURA.ne.jp>
Signed-off-by: NPablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The error path misses putting the timeout object. This patch adds
new function xt_ct_tg_timeout_put() to put the timeout object.
Reported-by: NTetsuo Handa <penguin-kernel@I-love.SAKURA.ne.jp>
Signed-off-by: NPablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Reported-by: NTetsuo Handa <penguin-kernel@I-love.SAKURA.ne.jp>
Signed-off-by: NPablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

NAPI is disabled during suspend and needs to be enabled on resume. Without
this the driver locks up during resume in rtl_reset_work() trying to disable
NAPI again.
Signed-off-by: NArtem Savkov <artem.savkov@gmail.com>
Acked-by: NFrancois Romieu <romieu@fr.zoreil.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Commit 621b4d66 updated the bnx2x driver to a new FW version, but lacked
a commit to a header file with changes to the firmware's interface.
The missing interface change causes iscsi and fcoe to misbehave with the
updated firmware.
Signed-off-by: NYuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: NDmitry Kravkov <dmitry@broadcom.com>
Signed-off-by: NEilon Greenstein <eilong@broadcom.com>
CC: Michael Chan <mchan@broadcom.com>
CC: Bhanu Prakash Gollapudi <bprakash@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch fixes Auto Power Saving configuration in ip101a_config_init
which was broken as there is no phy register write followed after
setting IP101A_APS_ON flag.

This patch also fixes the return value of ip101a_config_init.

Without this patch ip101a_config_init returns 2 which is not an error
accroding to IS_ERR and the mac driver will continue accessing 2 as
valid pointer to phy_dev resulting in memory fault.
Signed-off-by: NSrinivas Kandagatla <srinivas.kandagatla@st.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

In rare circumstances, a descriptor writeback flush may not work if it
arrives on a specific clock cycle as a writeback request is going out.
Signed-off-by: NMatthew Vick <matthew.vick@intel.com>
Tested-by: NAaron Brown <aaron.f.brown@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

When the adapter is closed while it is simultaneously going through a
reset, it can cause a null-pointer dereference when the two different code
paths simultaneously cleanup up the Tx/Rx resources.
Signed-off-by: NBruce Allan <bruce.w.allan@intel.com>
Tested-by: NAaron Brown <aaron.f.brown@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Fix up code so that changes in DCB settings
are detected only when ixgbe_dcbnl_set_all is called.
Previously, a series of 'change' commands followed by
a call to ixgbe_dcbnl_set_all() would always be handled
as a HW change - even if the net change was zero.
This patch checks for this case of no actual change and
skips going through the HW set process.

Without this fix, the link could reset and result in
a link flap.

The core change in this patch is to check for changes
in the ixgbe_copy_dcb_cfg() routine - and return
a bitmask of detected changes.  The other
places where changes were detected previously can be removed.
Signed-off-by: NEric Multanen <eric.w.multanen@intel.com>
Tested-by: NRoss Brattain <ross.b.brattain@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Now the helper function from filter.c for negative offsets is exported,
it can be used it in the jit to handle negative offsets.

First modify the asm load helper functions to handle:
- know positive offsets
- know negative offsets
- any offset

then the compiler can be modified to explicitly use these helper
when appropriate.

This fixes the case of a negative X register and allows to lift
the restriction that bpf programs with negative offsets can't
be jited.
Signed-of-by: NJan Seiffert <kaffeemonster@googlemail.com>
Signed-off-by: NEric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The function is renamed to make it a little more clear what it does.
It is not added to any .h because it is not for general consumption, only for
bpf internal use (and so by the jits).
Signed-of-by: NJan Seiffert <kaffeemonster@googlemail.com>
Acked-by: NEric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The explanation of ip_local_port_range in
Documentation/networking/ip-sysctl.txt contains several factual
errors:

- The default value of ip_local_port_range does not depend on the
  amount of memory available in the system.
- tcp_tw_recycle is not enabled by default.
- 1024-4999 is not the default value.
- Etc.

Clean up the mess.
Signed-off-by: NFernando Luis Vazquez Cao <fernando@oss.ntt.co.jp>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

vmsplice()/splice(pipe, socket) call do_tcp_sendpages() one page at a
time, adding at most 4096 bytes to an skb. (assuming PAGE_SIZE=4096)

The call to tcp_push() at the end of do_tcp_sendpages() forces an
immediate xmit when pipe is not already filled, and tso_fragment() try
to split these skb to MSS multiples.

4096 bytes are usually split in a skb with 2 MSS, and a remaining
sub-mss skb (assuming MTU=1500)

This makes slow start suboptimal because many small frames are sent to
qdisc/driver layers instead of big ones (constrained by cwnd and packets
in flight of course)

In fact, applications using sendmsg() (adding an additional memory copy)
instead of vmsplice()/splice()/sendfile() are a bit faster because of
this anomaly, especially if serving small files in environments with
large initial [c]wnd.

Call tcp_push() only if MSG_MORE is not set in the flags parameter.

This bit is automatically provided by splice() internals but for the
last page, or on all pages if user specified SPLICE_F_MORE splice()
flag.

In some workloads, this can reduce number of sent logical packets by an
order of magnitude, making zero-copy TCP actually faster than
one-copy :)
Reported-by: NTom Herbert <therbert@google.com>
Cc: Nandita Dukkipati <nanditad@google.com>
Cc: Neal Cardwell <ncardwell@google.com>
Cc: Tom Herbert <therbert@google.com>
Cc: Yuchung Cheng <ycheng@google.com>
Cc: H.K. Jerry Chu <hkchu@google.com>
Cc: Maciej Żenczykowski <maze@google.com>
Cc: Mahesh Bandewar <maheshb@google.com>
Cc: Ilpo Järvinen <ilpo.jarvinen@helsinki.fi>
Signed-off-by: NEric Dumazet <eric.dumazet@gmail&gt;com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

For every transmitted packet, ppp_start_xmit() will stop the netdev
queue and then, if appropriate, restart it. This causes the TX softirq
to run, entirely gratuitously.

This is "only" a waste of CPU time in the normal case, but it's actively
harmful when the PPP device is a TEQL slave — the wakeup will cause the
offending device to receive the next TX packet from the TEQL queue, when
it *should* have gone to the next slave in the list. We end up seeing
large bursts of packets on just *one* slave device, rather than using
the full available bandwidth over all slaves.

This patch fixes the problem by *not* unconditionally stopping the queue
in ppp_start_xmit(). It adds a return value from ppp_xmit_process()
which indicates whether the queue should be stopped or not.

It *doesn't* remove the call to netif_wake_queue() from
ppp_xmit_process(), because other code paths (especially from
ppp_output_wakeup()) need it there and it's messy to push it out to the
other callers to do it based on the return value. So we leave it in
place — it's a no-op in the case where the queue wasn't stopped, so it's
harmless in the TX path.
Signed-off-by: NDavid Woodhouse <David.Woodhouse@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Commit f04565dd (dev: use name hash for dev_seq_ops) added a second
regression, as some devices are missing from /proc/net/dev if many
devices are defined.

When seq_file buffer is filled, the last ->next/show() method is
canceled (pos value is reverted to value prior ->next() call)

Problem is after above commit, we dont restart the lookup at right
position in ->start() method.

Fix this by removing the internal 'pos' pointer added in commit, since
we need to use the 'loff_t *pos' provided by seq_file layer.

This also reverts commit 5cac98dd (net: Fix corruption
in /proc/*/net/dev_mcast), since its not needed anymore.
Reported-by: NBen Greear <greearb@candelatech.com>
Signed-off-by: NEric Dumazet <eric.dumazet@gmail.com>
Cc: Mihai Maruseac <mmaruseac@ixiacom.com>
Tested-by: NBen Greear <greearb@candelatech.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Pull drm update from Dave Airlie:
 "This pull just contains a forward of the Intel fixes from Daniel.

  The only annoyance is the RC6 enable, which really should have made
  -next, but since Ubuntu are shipping it I reckon its getting a good
  testing now by the time 3.4 comes out.

  The pull from Daniel contains his pull message to me:

    "A few patches for 3.4, major part is 3 regression fixes:
     - ppgtt broke hibernate on snb/ivb.  Somehow our QA claims that it
       still works, which is why this has not been caught earlier.
     - ppgtt flails in combination with dmar.  I kinda expected this one :(
     - fence handling bugfix for gen2/3.  Iirc this one is about a year
       old, fix curtesy Chris Wilson.  I've created an shockingly simple
       i-g-t test to catch this in the future."

     Wrt regressions I've just got a report that gmbus (newly enabled
     again in 3.4) is a bit noisy.  I'm looking into this atm.

     Also included are the rc6 enable patches for snb from Eugeni.  I
     wanted to include these in the main 3.4 pull but screwed it up.
     Please hit me.  Imo these kind of patches really should go in
     before -rc1, but in thise case rc6 has brought us tons of press and
     guinea pigs^W^W testers and ubuntu is already running with it.  So
     I estimate a pretty small chance for this to blow up.

     And some smaller things:
      - two minor locking snafus
      - server gt2 ivb pciid
      - 2 patches to sanitize the register state left behind by the bios
        some more
      - 2 new quirk entries
      - cs readback trick against missed IRQs from ivb also enabled on snb
      - sprite fix from Jesse"

Let's see if the "enable RC6 on sandybridge" finally works and sticks.
I've been enabling it by hand (i915.i915_enable_rc6=1) for several
months on my Macbook Air, and it definitely makes a difference (and has
worked for me).  But every time we enabled it before it showed some odd
hw buglet for *somebody*.

This time it's all good, I'm sure.

* 'drm-fixes-intel' of git://people.freedesktop.org/~airlied/linux:
  drm/i915: treat src w & h as fixed point in sprite handling code
  drm/i915: no-lvds quirk on MSI DC500
  drm/i915: Add lock on drm_helper_resume_force_mode
  drm/i915: don't leak struct_mutex lock on ppgtt init failures
  drm/i915: disable ppgtt on snb when dmar is enabled
  drm/i915: add Ivy Bridge GT2 Server entries
  drm/i915: properly clear SSC1 bit in the pch refclock init code
  drm/i915: apply CS reg readback trick against missed IRQ on snb
  drm/i915: quirk away broken OpRegion VBT
  drm/i915: enable plain RC6 on Sandy Bridge by default
  drm/i915: allow to select rc6 modes via kernel parameter
  drm/i915: Mark untiled BLT commands as fenced on gen2/3
  drm/i915: properly restore the ppgtt page directory on resume
  drm/i915: Sanitize BIOS debugging bits from PIPECONF

Pull drm fixes from Dave Airlie:
 "Mainly nouveau fixes, one for a regressions in -rc1, fixes for booting
  on a ppc G5, and a Kconfig fix.  Two radeon fixes, one oops, one s/r
  fix.  One udl mmap fix.  And one core drm fix to stop bad fbdev apps
  overwriting bits of ram."

* 'drm-fixes' of git://people.freedesktop.org/~airlied/linux:
  drm: Validate requested virtual size against allocated fb size
  drm/radeon: Don't dereference possibly-NULL pointer.
  mm, drm/udl: fixup vma flags on mmap
  drm/radeon/kms: fix fans after resume
  nouveau/bios: Fix tracking of BIOS image data
  nouveau: Fix crash when pci_ram_rom() returns a size of 0
  drm/nouveau: select POWER_SUPPLY
  drm/nouveau: inform userspace of relaxed kernel subchannel requirements
  Revert "drm/nouveau: inform userspace of new kernel subchannel requirements"
  drm/nouveau: oops, create m2mf for nvd9 too

Pull arch/microblaze fixes from Michal Simek.

* 'next' of git://git.monstr.eu/linux-2.6-microblaze:
  microblaze: Fix ret_from_fork declaration
  microblaze: Do not use tlb_skip in early_printk
  microblaze: Add missing headers caused by disintegration asm/system.h
  microblaze: Fix stack usage in PAGE_SIZE copy_tofrom_user
  microblaze: Fix tlb_skip variable on noMMU system
  microblaze: Fix __futex_atomic_op macro register usage

Pull m68k fixes from Geert Uytterhoeven:
 "Here are a few fixes for the m68k architecture.  Nothing fancy this
  time, just a build fix for the asm/system.h disintegration, and two
  fixes for missing platform checks (one got in during last merge
  window), which can cause crashes in multi-platform kernels."

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/geert/linux-m68k:
  m68k/q40: Add missing platform check before registering platform devices
  m68k/mac: Add missing platform check before registering platform devices
  m68k: include asm/cmpxchg.h in our m68k atomic.h

Merge branch 'drm-intel-fixes' of git://people.freedesktop.org/~danvet/drm-intel into drm-intel-fixes

From Daniel Vetter:

"A few patches for 3.4, major part is 3 regression fixes:
- ppgtt broke hibernate on snb/ivb. Somehow our QA claims that it still
 works, which is why this has not been caught earlier.
- ppgtt flails in combination with dmar. I kinda expected this one :(
- fence handling bugfix for gen2/3. Iirc this one is about a year old, fix
 curtesy Chris Wilson. I've created an shockingly simple i-g-t test to
 catch this in the future.

Wrt regressions I've just got a report that gmbus (newly enabled again in
3.4) is a bit noisy. I'm looking into this atm.

Also included are the rc6 enable patches for snb from Eugeni. I wanted to
include these in the main 3.4 pull but screwed it up. Please hit me. Imo
these kind of patches really should go in before -rc1, but in thise case
rc6 has brought us tons of press and guinea pigs^W^W testers and ubuntu is
already running with it. So I estimate a pretty small chance for this to
blow up.

And some smaller things:
- two minor locking snafus
- server gt2 ivb pciid
- 2 patches to sanitize the register state left behind by the bios some
 more
- 2 new quirk entries
- cs readback trick against missed IRQs from ivb also enabled on snb
- sprite fix from Jesse"

* 'drm-intel-fixes' of git://people.freedesktop.org/~danvet/drm-intel:
  drm/i915: treat src w & h as fixed point in sprite handling code
  drm/i915: no-lvds quirk on MSI DC500
  drm/i915: Add lock on drm_helper_resume_force_mode
  drm/i915: don't leak struct_mutex lock on ppgtt init failures
  drm/i915: disable ppgtt on snb when dmar is enabled
  drm/i915: add Ivy Bridge GT2 Server entries
  drm/i915: properly clear SSC1 bit in the pch refclock init code
  drm/i915: apply CS reg readback trick against missed IRQ on snb
  drm/i915: quirk away broken OpRegion VBT
  drm/i915: enable plain RC6 on Sandy Bridge by default
  drm/i915: allow to select rc6 modes via kernel parameter
  drm/i915: Mark untiled BLT commands as fenced on gen2/3
  drm/i915: properly restore the ppgtt page directory on resume
  drm/i915: Sanitize BIOS debugging bits from PIPECONF

mplayer -vo fbdev tries to create a screen that is twice as tall as the
allocated framebuffer for "doublebuffering". By default, and all in-tree
users, only sufficient memory is allocated and mapped to satisfy the
smallest framebuffer and the virtual size is no larger than the actual.
For these users, we should therefore reject any userspace request to
create a screen that requires a buffer larger than the framebuffer
originally allocated.

References: https://bugs.freedesktop.org/show_bug.cgi?id=38138Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: NDaniel Vetter <daniel.vetter@ffwll.ch>
Cc: stable@kernel.org
Signed-off-by: NDave Airlie <airlied@redhat.com>

This was missed when we converted the source values to 16.16 fixed point.

Cc: stable@vger.kernel.org
Signed-off-by: NJesse Barnes <jbarnes@virtuousgeek.org>
Tested-by: NChris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

This hardware doesn't have an LVDS, it's a desktop box. Fix incorrect
LVDS detection.

Cc: stable@kernel.org
Signed-off-by: NAnisse Astier <anisse@astier.eu>
Acked-by: NChris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

i915_drm_thaw was not locking the mode_config lock when calling
drm_helper_resume_force_mode. When there were multiple wake sources,
this caused FDI training failure on SNB which in turn corrupted the
display.
Signed-off-by: NSean Paul <seanpaul@chromium.org>
Reviewed-by: NChris Wilson <chris@chris-wilson.co.uk>
Cc: stable@kernel.org
Signed-Off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Reported-by: NKonstantin Belousov <kostikbel@gmail.com>
Reviewed-by: NChris Wilson <chris@chris-wilson.co.uk>
Signed-Off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

If CONFIG_NF_CONNTRACK_TIMEOUT=n we have following warning :

  CC [M]  net/netfilter/xt_CT.o
net/netfilter/xt_CT.c: In function ‘xt_ct_tg_check_v1’:
net/netfilter/xt_CT.c:284: warning: label ‘err4’ defined but not used
Reported-by: NEric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: NPablo Neira Ayuso <pablo@netfilter.org>

Pull dma-buf prime support from Dave Airlie:
 "This isn't a majorly urgent thing to have, but we'd like to set the
  stage for working on dma-buf support in the drm drivers for the next
  merge window, so I'd like to push in the initial submission now so
  people have something that we can build on top of.  The code just
  introduces the user interface and internal helper functions for
  drivers to use.

  We have driver support under development for i915, nouveau, udl on x86
  and exynos, omapdrm on arm, which we would be aiming for the next
  merge window."

In the -rc1 announcement I asked for people who would use this to
comment on it, and got severa "Yes please" from people for this and for
HSI (that I merged earlier).

So far crickets on pohmelfs and the DMA-mapping infrastructure.

* 'drm-prime-dmabuf-initial' of git://people.freedesktop.org/~airlied/linux:
  drm: base prime/dma-buf support (v5)