Allow configuring the default destination port on a per-device basis.
Adds new netlink paramater IFLA_VXLAN_PORT to allow setting destination
port when creating new vxlan.
Signed-off-by: NStephen Hemminger <stephen@networkplumber.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Rather than computing source port and returning it in host order
then swapping later, go ahead and compute it in network order to
start with. Cleaner and less error prone.
Signed-off-by: NStephen Hemminger <stephen@networkplumber.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Source compatiability for build iproute2 was broken by:
  commit c7995c43
  Author: Atzm Watanabe <atzm@stratosphere.co.jp>
    vxlan: Allow setting destination to unicast address.

Since this commit has not made it upstream (still net-next),
and better to avoid gratitious changes to exported API's;
go back to original definition, and add a comment.
Signed-off-by: NStephen Hemminger <stephen@networkplumber.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The NDA_PORT attribute was added, but the author wasn't careful
about width (port is 16 bits), or byte order.  The attribute was
being dumped as 16 bits, but only 32 bit value would be accepted
when setting up a device. Also, the remote port is in network
byte order and was being compared with default port in host byte
order.
Signed-off-by: NStephen Hemminger <stephen@networkplumber.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The default port for VXLAN is not same as IANA value.
Document this.
Signed-off-by: NStephen Hemminger <stephen@networkplumber.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NStephen Hemminger <stephen@networkplumber.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Current bridge fdb update code does not seem to update the port
during fdb update. This patch adds a check for fdb dst (port)
change during fdb update. Also rearranges the call to
fdb_notify to send only one notification for create and update.

Changelog:
v2 - Change notify flag to bool
Signed-off-by: NRoopa Prabhu <roopa@cumulusnetworks.com>
Signed-off-by: NStephen Hemminger <stephen@networkplumber.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Jeff Kirsher says:

====================
This series contains updates to e1000e, igb and ixgbe.

There are 2 patches in this series which could be applied to net,
but since Linus is so very close to releasing 3.9, I do not think
it prudent to try and push these into net at this time.  I have CC'd
stable on these patches so that they can queue them up as soon as
3.9 gets released.

The 2 patches are:
  e1000e: fix numeric overflow in phc settime method
  ixgbe: fix EICR write in ixgbe_msix_other

Richard provides a fix for e1000e by using a helper function from time.h
to resolve a unintended overflow in the PTP settime function.

Bruce provides a fix to wait for NAPI to be done with the current context
after disabling interrupts and then disable NAPI when the interface
is going down.  This fixes a possible "unable to handle kernel paging
request" panic in net-next.

Andi Kleen provides a patch for igb to use mdelay instead of udelay
when we needed 100000us.

Jacob provides a fix for ixgbe to simply mask the lower 16bits off so that
ixgbe_msix_other does not write them in the EICR, which causes them to
remain high and be properly handled by the clean_rings interrupt routine
as normal.

Emil cleans up the logic in ixgbe_setup_loopback_test() to only access
registers applicable to the MAC type.  In addition, removes majority
of the AUTOC register reads by using a cached value instead to avoid
writing corrupted values to AUTOC due to bad FW.  Emil also add support
for disabling link during boot time.  Lastly, he provides a patch which
adds the MAC type to the version in ethtool_regs which will make it
easier to check the MAC type when dumping registers with ethtool.

There is a separate ethtool tool patch which is dependent upon Emil's
last patch of the series to add the MAC type to the version in
ethtool_regs, which will be sent separately.
====================
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Or Gerlitz says:

====================
This series adds support for the SRIOV ndo_set_vf callbacks to the mlx4 driver.

Series done against the net-next tree as of commit 37fe0660 "net:
fix address check in rtnl_fdb_del"

We have successfully tested the series on net-next, except for getting
the VF link info issue I have reported earlier today on netdev, we
see the problem for both ixgbe and mlx4 VFs. Just to make sure get
VF config is working OK with patch #6 - we have run it over 3.8.8 too.

We added to the V1 series two patches that disable HW timestamping
when running over a VF, as this isn't supported yet.
====================
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Support getting VF config.
Signed-off-by: NRony Efraim <ronye@mellanox.com>
Signed-off-by: NOr Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add ndo_set_vf_spoofchk support
Signed-off-by: NRony Efraim <ronye@mellanox.com>
Signed-off-by: NOr Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add support to ndo_set_vf_vlan in the driver. Once this call is used the vport
is considered to be in VST mode. In this mode, the PPF driver configures
Ethernet QPs created by this VF to use this vlan id and priority. Currently
RoCE isn't supported on that mode.

The special values of VID=4095 or VID=0,UP=0 are considered as VGT.
Signed-off-by: NRony Efraim <ronye@mellanox.com>
Signed-off-by: NOr Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add ndo_set_vf_mac support which allows to set the MAC address
for mlx4 VF Ethernet NICs from the host.
Signed-off-by: NRony Efraim <ronye@mellanox.com>
Signed-off-by: NOr Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch add struct mlx4_vport_state where all the parameters related
to management of VFs port (virtual ports of the NIC eswitch) are kept.

The driver keeps an administrative and operational copy of the settings.
The current administrative copy becomes operational on the event of probing
a VF either on a VM or on the host.
Signed-off-by: NRony Efraim <ronye@mellanox.com>
Signed-off-by: NOr Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add reference counting to the driver MAC registeration code. This would
be needed for cases where a mac is registered from more than once, e.g
when both the host and the VM driver register the same mac, the host
for mac spoof protection purposes and the VM for its regular needs.
Signed-off-by: NRony Efraim <ronye@mellanox.com>
Signed-off-by: NOr Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Should not run HW clock overflow check if HW clock is not supported. Also, since
this watchdog is the only customer of service_task, no need to start it in that case.
Signed-off-by: NAmir Vadai <amirv@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Disable timestamp capability on virtual functions.
Signed-off-by: NAmir Vadai <amirv@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

'attrbuf' is malloced in genl_family_rcv_msg() when family->maxattr &&
family->parallel_ops, thus should be freed before leaving from the error
handling cases, otherwise it will cause memory leak.

Introduced by commit def31174
(genl: Allow concurrent genl callbacks.)
Signed-off-by: NWei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NSuresh Reddy <suresh.reddy@emulex.com>
Signed-off-by: NSarveshwar Bandi <sarveshwar.bandi@emulex.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NSuresh Reddy <suresh.reddy@emulex.com>
Signed-off-by: NSarveshwar Bandi <sarveshwar.bandi@emulex.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NSuresh Reddy <suresh.reddy@emulex.com>
Signed-off-by: NSarveshwar Bandi <sarveshwar.bandi@emulex.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch adds the mac type to the version in ethtool_regs.

This will make it easier to check the mac type when dumping registers with
ethtool. The drawback of this is that older versions of ethtool will only
be able to dump in hex format for 82599 and above  when used with the updated
driver.
Signed-off-by: NEmil Tantilov <emil.s.tantilov@intel.com>
Tested-by: NPhil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This patch adds support for disabling link during boot time. This
feature was requested by customers and is configurable through the EEPROM.
Signed-off-by: NEmil Tantilov <emil.s.tantilov@intel.com>
Tested-by: NPhil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This patch removes majority of the AUTOC register reads by using a cached
value instead.

The reason for this change is to avoid writing corrupted values to AUTOC
due to bad FW.
Signed-off-by: NEmil Tantilov <emil.s.tantilov@intel.com>
Tested-by: NPhil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This patch cleans up the logic in ixgbe_setup_loopback_test() to only access
registers applicable to the MAC type. AUTOC is only valid on MACs older than
X540. MACC is used for X540.

In addition it removes a read of AUTOC and uses the stored value to force the
link up.
Signed-off-by: NEmil Tantilov <emil.s.tantilov@intel.com>
Tested-by: NPhil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Previously, the ixgbe_msix_other was writing the full 32bits of the set
interrupts, instead of only the ones which the ixgbe_msix_other is
handling. This resulted in a loss of performance when the X540's PPS feature is
enabled due to sometimes clearing queue interrupts which resulted in the driver
not getting the interrupt for cleaning the q_vector rings often enough. The fix
is to simply mask the lower 16bits off so that this handler does not write them
in the EICR, which causes them to remain high and be properly handled by the
clean_rings interrupt routine as normal.
Signed-off-by: NJacob Keller <jacob.e.keller@intel.com>
Cc: stable <stable@vger.kernel.org>
Tested-by: NPhil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

If you really want 100000us you should really use mdelay or so.

Found by the LTO kernel build
Signed-off-by: NAndi Kleen <ak@linux.intel.com>
Tested-by: NAaron Brown <aaron.f.brown@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

An "unable to handle kernel paging request" panic can occur when receiving
traffic while the interface is going down.  Wait for NAPI to be done with
current context after disabling interrupts and then disable NAPI.

See https://bugzilla.vyatta.com/show_bug.cgi?id=8837.
Reported-by: NStephen Hemminger <stephen@networkplumber.org>
Signed-off-by: NBruce Allan <bruce.w.allan@intel.com>
Tested-by: NAaron Brown <aaron.f.brown@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

The PTP Hardware Clock settime function in the e1000e driver
computes nanoseconds from a struct timespec. The code converts the
seconds field .tv_sec by multiplying it with NSEC_PER_SEC. However,
both operands are of type long, resulting in an unintended overflow.
The patch fixes the issue by using the helper function from time.h.

CC: stable <stable@vger.kernel.org>
Signed-off-by: NRichard Cochran <richardcochran@gmail.com>
Tested-by: NAaron Brown <aaron.f.brown@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Commit 6681712d
	vxlan: generalize forwarding tables

relaxed the address checks in rtnl_fdb_del() to use is_zero_ether_addr().
This allows users to add multicast addresses using the fdb API.  However,
the check in rtnl_fdb_del() still uses a more strict
is_valid_ether_addr() which rejects multicast addresses.  Thus it
is possible to add an fdb that can not be later removed.
Relax the check in rtnl_fdb_del() as well.
Signed-off-by: NVlad Yasevich <vyasevic@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

During high throughput it is likely that we receive both: an RX and TX
interrupt. The normal behaviour is that once we enter the ISR the
interrupts are disabled in the IRQ chip and so the ISR is invoked only
once and the interrupt line is disabled once. It will be re-enabled
after napi completes.
With threaded interrupts on the other hand the interrupt the interrupt
is disabled immediately and the ISR is marked for "later". By having TX
and RX interrupt marked pending we invoke them both and disable the
interrupt line twice. The napi callback is still executed once and so
after it completes we remain with interrupts disabled.

The initial patch simply removed the cpsw_{enable|disable}_irq() calls
and it worked well on my AM335X ES1.0 (beagle bone). On ES2.0 (beagle
bone black) it caused an never ending interrupt (even after the mask via
cpsw_intr_disable()) according to Mugunthan V N. Since I don't have the
ES2.0 and no idea what is going on this patch tracks the state of the
irq_disable() call and execute it only when not yet done.
The book keeping is done on the first struct since with dual_emac we can
have two of those and only one interrupt line.
Signed-off-by: NSebastian Andrzej Siewior <bigeasy@linutronix.de>
Acked-by: NMugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

text    data     bss     dec     hex filename
15530      92       4   15626    3d0a cpsw.o.before
15478      92       4   15574    3cd6 cpsw.o.after

52 bytes smaller, 13 for each invocation.
Signed-off-by: NSebastian Andrzej Siewior <bigeasy@linutronix.de>
Acked-by: NMugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This driver does not clean up properly after leaving. Here is a list:
- Use unregister_netdev(). free_netdev() is good but not enough
- Use the above also on the other ndev in case of dual mac
- Free data.slave_data. The name of the strucre makes it look like
  it is platform_data but it is not. It is just a trick!
- Free all irqs. Again: freeing one irq is good start, but freeing all
  of them is better.

With this rmmod & modprobe of cpsw seems to work. The remaining issue
is:
|WARNING: at fs/sysfs/dir.c:536 sysfs_add_one+0x9c/0xd4()
|sysfs: cannot create duplicate filename '/devices/ocp.2/4a100000.ethernet/4a101000.mdio'
|WARNING: at lib/kobject.c:196 kobject_add_internal+0x1a4/0x1c8()

comming from of_platform_populate() and I am not sure that this belongs
here.
Signed-off-by: NSebastian Andrzej Siewior <bigeasy@linutronix.de>
Acked-by: NMugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

If compiled as modules each one of these modules is missing something.
With this patch the modules are loaded on demand and don't taint the
kernel due to license issues.
Signed-off-by: NSebastian Andrzej Siewior <bigeasy@linutronix.de>
Acked-by: NMugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

In case that we run into OOM during the allocation of the new rx-skb we
don't get one and we have one skb less than we used to have. If this
continues to happen then we end up with no rx-skbs at all.
This patch changes the following:
- if we fail to allocate the new skb, then we treat the currently
  completed skb as the new one and so drop the currently received data.
- instead of testing multiple times if the device is gone we rely one
  the status field which is set to -ENOSYS in case the channel is going
  down and incomplete requests are purged.
  cpdma_chan_stop() removes most of the packages with -ENOSYS. The
  currently active packet which is removed has the "tear down" bit set.
  So if that bit is set, we send ENOSYS as well otherwise we pass the
  status bits which are required to figure out which of the two possible
  just finished.
Acked-by: NMugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: NSebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The gfp_mask argument is not used in cpdma_chan_submit() and always set
to GFP_KERNEL even in atomic sections. This patch drops it since it is
unused.
Acked-by: NMugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: NSebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

netif_running() reports false before the ->ndo_stop() callback is
called. That means if one executes "ifconfig down" and the system
receives an interrupt before the interrupt source has been disabled we
hang for always for two reasons:
- we never disable the interrupt source because devices claim to be
  already inactive and don't feel responsible.
- since the ISR always reports IRQ_HANDLED the line is never deactivated
  because it looks like the ISR feels responsible.

This patch changes the logic in the ISR a little:
- If none of the status registers reports an active source (RX or TX,
  misc is ignored because it is not actived) we leave with IRQ_NONE.
- the interrupt is deactivated
- The first active network device is taken and napi is scheduled. If
  none are active (a small race window between ndo_down() and the
  interrupt the) then we leave and should not come back because the
  source is off.
  There is no need to schedule the second NAPI because both share the
  same dma queue.
Signed-off-by: NSebastian Andrzej Siewior <bigeasy@linutronix.de>
Acked-by: NMugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

if during "ifconfig up" we run out of mem we continue regardless how
many skbs we got. In worst case we have zero RX skbs and can't ever
receive further packets since the RX skbs are never reallocated. If
cpdma_chan_submit() fails we even leak the skb.
This patch changes the behavior here:
If we fail to allocate an skb during bring up we don't continue and
report that error. Same goes for errors from cpdma_chan_submit().
While here I changed to __netdev_alloc_skb_ip_align() so GFP_KERNEL can
be used.
Signed-off-by: NSebastian Andrzej Siewior <bigeasy@linutronix.de>
Acked-by: NMugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

__cpdma_chan_process() holds the lock with interrupts off (and its
caller as well), same goes for cpdma_ctlr_start(). With interrupts off,
jiffies will not make any progress and if the wait condition never gets
true we wait for ever.
Tgis patch adds a a simple udelay and counting down attempt.
Acked-by: NMugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: NSebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Need remove erroneous semicolon, which is found by EXTRA_CFLAGS=-W,
the related commit number: c5441932
("GRE: Refactor GRE tunneling code")
Signed-off-by: NChen Gang <gang.chen@asianux.com>
Acked-by: NPravin B Shelar <pshelar@nicira.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>